Search Documents

By Charles A. Morgan

The proms of mire drawing depends upon the property which certain metals possess, termed ductility, which is defined in Brande's Dictionary of Science as a property inconhequcnce of which metals may be drawn out at length wilhotit interrupting the continuity of their constituent parts. As ticfincd thy M. Tresca, it is the property of flowing when subjected to pressure, and ie termed by him the "flow of solids," in his paper, read before the AcaiXemy of Sciences in Paris, November, 1866 * In the simple language of the wire shop, it is that quality in certain metals that thcm to be drawn (or etretched) out througl~ a tapering hole in a metal block or die, the die being more dense and harder than the metal to be redud. It is a fact well known to tllose slrillet1 in the ai*, that to eu~xeed in drawing iron or steel wire, it is of' the utmost, importance to have tborough lubritatiun, as a lack of it woullii udu-se abrasion of the wire, or of the walls of the tapering hole in the dia or plate, and quickly put an end to the operation. In drawing coarse or large sizes of pire, say & inoh diameter, the pressure upon the sides of the tay~dng hole, where the wire comes i.u contact with the die, so great that an ordina,y labricaot is equeezed out when the nsoal rc~luctions iu size are matie, and abrasion takea place. In order to meet this diffic:ulty, and emure proper lubrication, it has been a ccmmon prtictice for yazrs to apply a paste made of rye or wheaten flour, or lime, to the surface of the wire to be drawn, and when the pnstc is dry, to smwr tl~e wire with tallow or grease; the wire is then ready to be draw, the dried pa serving fo prevent the lubricant from being presetf out in the prows. Some years since, when Bessemer metal came iargely into use material for wire, 'the writer fourid that its dmwing requid so much more power than iron wire, that he was led to institute a. series of trials to ascertain the difference in power required. It was fotind that Bessemer wire requircd from 100 to 200 per cent. more power to makc the same reduction in sizes than soft iron wire, the difference depending npou the amount of carbon and other chemical constitu-

Jan 1, 1881

By I. Serepa, N. C. Steenkamp

Investigations were conducted to determine the condition and stability of the existing decline at amine in the Kalahari Manganese Field, Northern Cape Province, South Africa. During the inspection of the decline, voids were identified behind the concrete lining on the hangingwall and sidewalls over a total linear distance of 230 m. The voids did not provide confinement and, as a result, self-mining was occurring behind the lining. Water was flowing into the decline, over a total linear distance of 100 m, at areas where the decline intersected incompetent rock units, causing softening of the concrete lining and deterioration of the surrounding rock mass. Further damage to the concrete lining was caused by expansion and contraction of the wet red clay unit. Remedial work comprised void filling and water sealing to prevent further deterioration of the decline and ensure that it remained operable for the remainder of the life of mine. Void filling was accomplished by drilling rows of holes along the decline to access the voids and filling the voids with foam. This was followed by the sealing with polymer fluids. Telescopic pipes were also installed to allow water to drain off. A visual inspection was conducted and check-holes were drilled to assess the quality of the remedial work. The void filling material had penetrated cracks in the concrete lining, and areas where voids were intersected by check-holes were re-filled. Additional holes were drilled to re-seal areas that were still wet. The remedial work was completed successfully, as all voids were filled and stability achieved without compromising the concrete lining. The ingress of groundwater was also reduced to some residual dampness.

Mar 2, 2022

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By M. C. Leverett

THE behavior of mixtures of immiscible liquids in porous solids is of rapidly increasing interest to those engaged in the production of petro-leum. The operation of artificial water-floods and the control of natural ones immediately raise questions concerning the fundamental nature of such processes. Moreover, it is now recognized that often water occurs dispersed throughout the rock from which the oil issues into the well,1 and thus tends to move toward the well simultaneously with the oil. The work reported here is a laboratory investigation of the simultaneous, steady-state flow of oil and water through the same column of uncon-solidated sand. It is thus directly related to the situation in which water occurs in oil-producing sands; it may have less direct implications for the displacement of oil from sands by water. However, it is to be clearly understood that the experiments to be described were performed pri-marily to obtain information of a more or less fundamental nature, and are not an attempt to reproduce, on laboratory scale, any part of an oil field. The dynamic behavior of a system in which oil and water are flowing simultaneously through sand is best described in terms of its "effective permeability" to either phase. For incompressible fluids flowing through a system of uniform cross section, the effective permeabilities to the two phases, in darcys, may be defined by the equations:

Jan 1, 1938

Greater automation of facilities is probably the best hope of the mining industry in its efforts to surmount continually rising labor costs. Underground mining, with its inherently low unit labor output, is especially vulnerable to rising costs, and here maximum automation is becoming increasingly important. One area of such operations that has been receiving a great deal of investigation is that of ore haulage and hoisting, two steps that often account for 10-35% of underground operating costs. Innovations and experimentation by mining firms and manufacturers over the past few years have resulted in larger, faster and more efficient tramming and hoisting equipment, but the White Pine Copper Co., at its operation in the Upper Peninsula of Michigan, is preparing to start up an entirely new concept in haulage later this summer. Known as the Dashaveyor System, it consists of individually powered modules (cars) that run on tracks inside a rectangular tube or on an open trackway at predetermined speeds up to 50 mph. At White Pine the Dashaveyor will be used to carry ore (crushed underground to -10 in.) from the mine to the concentrator. Dr. James Boyd, president of Copper Range Co., which is a 25% shareholder in The Dashaveyor Co., has indicated that if the Dashaveyor meets the expectations for surface operation, it will also be used underground for ore transport in place of the several miles of conveyor belts currently in use (Business Week, July 29, 1967).

Jan 7, 1968

The importance of proper planning, preparation, and execution of a steady state sampling campaign for metallurgical plant assessment must not be underestimated. Careful planning can increase the amount and reliability of information from an optimum number of samples and fully utilize available plant data. It requires specification of the data required, determination of run duration sampling frequency, the selection, modification and testing of sample points and cutters, as well as organisation and briefing of plant and sampling personnel. Preparation immediately prior to sampling, the conduct of the sampling campaign itself and procedures to handle the collected samples and information are discussed. Cutter design, fabrication and use are described in detail, and typical sampling situations, for ball mills, classifiers, pipes, launders, flotation cells and thickeners are considered individually. Measurement of pulp flow rate can often resolve difficult mass balance problems, and discussion of convenient techniques is included.

Jan 1, 1976

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By Roy G. Stott, John A. Johnson, Floyd G. Anderson

"This information circular discusses drilling and blasting in open-cut iron-ore mines and is one of a series of papers describing iron-ore mining practices in the Lake Superior district to aid in preventing accidents in that industry.The Lake Superior district consists of the Marquette and Menominee ranges of Michigan, the Gogebic range of Michigan and Wisconsin, and the Vermilion, Mesabi, and Cuyuna range of Minnesota. Open-cut mines produce 8o percent of the iron ore mined in the district; 98 percent of the total Lake Superior district open-cut ore is produced in Minnesota and 2 percent in Michigan. The entire Wisconsin iron-ore production is from underground nines. The Mesabi range in Minnesota produced 93 percent of the open-cut iron ore and 76 percent of the total iron ore in the district in 1947.During the 8-year period 1940-47, 619,000,000 gross tons of iron ore were shipped from mines of the district, or 85 percent of the United States output. Approximately 78,000,000 gross tons of iron ore were shipped from the mines of Minnesota, Michigan, and Wisconsin in 1947.This paper is based primarily on observations daring the period July 1947 to March 1948. Thirty-two open-cut mines were visited; 28 on the Mesabi range, 3 on the Cuyuna range, and 1 on the Marquette range. In 1947, 36,100,000 tons of iron ore was shipped from these 32 mines, or 59 percent of the open-cut ore and 46 percent of the total iron ore shipped from the district. During 1947 about 90 open-cut iron-ore mines were operating in the district, and the annual production of each ranged from 25,000 to 10,000,000 tons.Many recommendations included in this paper for improving safety and preventing injuries to employees were taken from Bureau of Mines Information Circular 7387.Data were collected under the direction of Frank E. Cash, former supervising engineer, Health and Safety Division, Bureau of Nines, Duluth, Minnesota. E. W. Felegy, mining engineer, Safety Branch, gave valuable assistance in reviewing and editing the manuscript.The authors gratefully acknowledge the information and assistance given and the numerous courtesies extended to them by officials of the following mining companies:All the Lake Superior iron ores occur in bedded formations that range from less than 100 feet to over 2,000 feet in thickness. These formations are designated by one commonly applied name, ""iron formations.""4/The Mesabi range in northern Minnesota, about 70 miles northwest of Duluth, was opened to mining in 1892; it is the largest single source of iron ore in the United States. It is 75 miles long and, because of the gentle dip of the ore formation, it ranges in width from 1-1/2 to 3 miles.5/ The ore formation, which is nearly horizontal, has a maximum thickness of about 450 feet and is covered by a glacial drift that ranges from 10 to over 100 feet in thickness. Most of the ore is near the surface and adaptable to open-cut mining."

Mar 1, 1950

By F. Calizaya

This study summarizes the ventilation requirements for the highly mechanized PT. Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The deep ore zone (DOZ) is a coppergold deposit that is being developed underneath the current intermediate ore zone (IOZ) mine. One of the company's current plans is to prepare this mine for a steady ore flow of 25 kt/d (27,500 stpd) by 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 2000

By C. Lurie

This final report describes the work performed by Gulton Battery Corporation under USBM Contract No. HO-112033, entitled "Research and Development on Lithium-Nickel Fluoride Batteries For Mint Life Support Equipment". The lithium-nickel fluoride couple was chosen For this investigation because of its high theoretical energy density (626 Wh/lb), its ability to operate at ambient temperatures and the fact that it showed promise as a secondary system. The theoretical energy density of the lithium-nickel fluoride couple is ten times greater than that of the widely used lead-acid battery and three times greater than the silver-zinc battery which has the highest theoretical energy density of the commercially available secondary systems. The experimental program first evaluated the cell components individually. The results of these studies then formed the basis for investigations of cell performance using experimental three-plate cells. These cells consisted of one nickel-fluoride and two lithium electrodes. All work was performed in a glove box under an argon atmosphere which was sufficiently pure to maintain the shiny appearance on freshly prepared lithium surfaces. The major portion of the work effort was concerned with the nickel fluoride electrode. Binder, conductive diluent, fabrication technique, as well as the nickel fluoride active material itself, were considered. Criteria for binder materials were established and six classes of materials encompassing thirteen binders were evaluated. The candidate materials were initially screened for appropriate chemical and physical properties and finally evaluated in three.-plate cells, Two epoxy powders emerged as the most promising binders. Two types of conductive diluent were evaluated. The first is a carbon black of low bulk density and high surface area. This material is a good conductive diluent; however, electrodes fabricated with it lacked good mechanical strength. It was hypothesized that a uni¬form, small particle size, low specific surface area would improve the mechanical properties of the electrodes. Therefore, two samples of graphicic materials, milled to uniform powders in the one-to-ten micron range were evaluated. Electrodes prepared with the graphitic materials had superior mechanical properties, However, their electrical performance was significantly poorer and voltage losses of 0.2 to 0.3 volts were observed. Several electrolyte solutions were evaluated. N-Methyl-2-Pyrrolidone was tested but found to be incompatible in the presence of lithium. Lithium perchlorate, lithium hexafluoroarsenate, and lithium bromide were tested as two-component electrolytes in propylene carbonate solvent and their performance compared with that of the single electrolyte solutions, Lithium perchlorate gave the best performance. Lithium hexafluoroarsenate was also evaluated in methyl formate and appears to give equivalent performance. The lithium perchlorate-propylene carbonate system is preferred as it is easier to handle and less expensive.

Jan 1, 1973

By Madan B. Karkee

The understanding and the development of sound theoretical basis concerning the pile foundations has been phenomenal during the past few decades, considering the thousands of years the piles have evidently been in use. The importance of the quality assurance and the need for verification of load bearing capacity is being further reinforced rather than undermined by these developments. This is evidenced by significant developments made in the pile load test technology in recent decades, making it possible to make judicious selection of a test method, or a package of test methods, suitable for a given situation. The selection depends on the objective of carrying out the test and the reliability desired. Presently, the possible selection ranges from dynamic to static methods. The extent of dynamic effect in a test can be reckoned based on a dimensionless parameter defined as the 'relative duration'. Examples of different load tests are given for illustration of the different methods currently in use.

Jan 1, 1997

By G V. R Goodman, G J. Chekan, J M. Listak

The extraction and transport of coal from underground coal mines can result in significant liberation of coal and/or silica dust into the mine atmosphere. Mine operators have long used ventilating air as a primary means of diluting generated dust, removing dust from the working faces and preventing dust from reaching the minersÆ working environment. As production levels have increased, mine operators continue to be challenged in maintaining dust concentrations below compliance levels. The need for maximising the effectiveness of available ventilating air in conjunction with other effective controls, such as water sprays and dust collectors, continues to be critical to the long-term health of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale laboratory and mine-site research to evaluate improved application of dust controls for both longwall and continuous mining methods. A summary of recent research results and recommended practices will be provided.

Jan 1, 2005

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By Z. S. Abisheva

Results of the study targeted to development of universal acidic-extraction-precipitation technology for gallium recovery from the sublimates are presented in the paper. This will let to utilize a new non-traditional source for gallium production. Phase composition of gallium containing dust was studied. Forms of gallium in the sublimates were determined. The main form is Ga2O3, however, GaP form is also present in the cottrel dust and Na5Ga3F14 form is present in the dust of aluminum electrolysis. The possibility of gallium concentration was established via secondary pyro-selection of the dust. Kinetics of interaction of dust components with sulfuric acid was studied. The products of the interaction subsequently were leached with water. Optimum conditions for direct leaching with HCl and H2SO4 were determined providing gallium recovery from the cottrel dust and the ash carry outs up to 95 %. Gallium recovery from the primary dust and the secondary dust of aluminum electrolysis was at 52; 64 % and 63; 83 % respectively. Effect of Fe, P, K, Na and Al admixtures for gallium extraction from hydrochloric acid solutions was studied. It was shown that gallium chloride complex (GaCl4-) is extracted into the organic phase from the following acid mixtures: HCl + H2SO4, HCl + H3PO4, HCl + H2SO4 + H3PO4, HCl + HF. Kinetic regularities of gallium extraction in the system (tri butyl phosphate) TBP ? HCl - Ga were studied using diffusion cell method with agitation. Optimum conditions for gallium extraction from complex hydrochloric acid solutions with TBP were found providing 99.9 % recovery and separation coefficient for gallium and iron (III) of more than 25 in one stage. Sodium hydroxide and water were selected as reagents for re-extraction of gallium from the organic phase. Different options for disposal of by-products that are formed in the processing of cottrel dust, ash sublimates and dust of aluminum electrolysis were proposed and tested. Keywords: gallium, kinetic, sulfatization, leaching, extraction, technology

Sep 1, 2012

By Hans M. Ewoldsen

The generation and evaluation of solutions to body force problems is of extreme interest to the geotechnical profession, as all natural stress states must necessarily include some contribution from the weight of the material. In this chapter the elastic solution for the stress field around a circular, horizontal tunnel at an arbitrary depth beneath the surface of a half-space is reexamined. The influences of body force, initial stress, and free surface proximity are examined and related to in-situ cases. The solution as presented deals only with an isotropically elastic medium; this medium is further considered only in a half-space configuration. It is readily apparent that these restrictions impose severe limitations if analogies are attempted with in-situ cases where geologic discontinuities, inhomogeneities, and irregular boundaries exist. The question might be raised as to the propriety of geotechnically oriented researchers even considering such idealized conditions. There is, however, much to be gained from study of such solutions. The lack of geologic discontinuities and inhomogeneities allows the investigator to separate and leisurely examine such parameters as are included in the solution, without worry of interrelationships of a host of other parameters. Further, elastic solutions have had extensive usage prior to the development of such techniques as the finite-element solution. It is interesting to compare body force solutions with the external field solutions which in the past have been used for design purposes. Finally, the exact solution may be used to verify the accuracy of the finite-element type of solution. The mathematical solution on which this chapter is based was originally developed by R. D. Mindlin.l Because of the complexity and length of the solution, no attempt was made to determine the resultant stress fields until the advent of the present-day high-speed digital computer. How-

Jan 1, 1972

The Mount Isa mine in North West Queens- land produces a total of nearly 10 million t/yr from separate copper and silver lead zinc orebodies. Sampling information is mainly obtained from diamond drilling on 30 to 40 metre centers in both types of orebodies. For the copper orebodies the majority of the core is analysed for copper content using a non-destructive bulk analyser developed by the Australian Atomic Energy Commission. The diamond drill core in the silver lead zinc orebodies is usually sam- pled as sawn half core and assayed in the com- pany laboratory using a variety of methods dependent upon the level of metal content and/or the elements required. Underground development is sampled where additional information is required to improve the ore reserve estimate. The copper areas are sampled using a standard 2.0 m by 2.0 m chip sample of the wall. The chips are taken on a 250 mm spacing. Lead areas are sampled using a 100 mm wide by 4 mm deep channel over intervals determined by the area geologists. The massive, irregularly shaped copper ore bodies are mined as large sublevel open stopes and pillars. Ore reserve estimation on both a production unit and global scale is routinely carried out using a geostatistical system developed in-house and running on a Sperry 1100 mainframe computer. Copper grade, tonnes and the Kriging var- iance are estimated at points on a user defined grid. The Kriging program uses 10 m assay composites from diamond drill core and underground chip samples. One average (rela- tive) variogram is used throughout the main copper orebodies. The validity of using an average variogram was verified by the original geostatistical study undertaken in the late 1970's.

Jan 1, 1987

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By P. G. Clites

A laboratory furnace was developed by the Federal Bureau of Mines for use in studying the interrelationships among variables associated with skull melting and casting high-temperature metals. Although additional work is necessary to determine the extent to which the information obtained by using this furnace can be extrapolated to larger furnaces of the same type, many casting characteristics of metals and alloys can be determined on equipment of this size. This furnace is a laboratory-size, consumable-electrode, skull-casting furnace equipped with a water-cooled copper ladle. The ladle, which is a tilt-pour or over-the-lip type, has a volume of approximately 30 cubic inches and provides up to 20 cubic inches of molten metal for castings. Castings of various reactive and refractory metals, including zirconium, titanium, hafnium, columbium, molybdenum, tantalum, and tungsten, have been produced. In addition, castings of iron, chromium, and copper have been made. The simplicity and versatility of the apparatus would make it useful to metallurgical laboratories preparing cast specimens.

Jan 1, 1961

By H. J. B. Couto, J. G. S. Puelles, M. L. Torem, R. H. Rojas, A. G. Merma

Understanding the limits of fine particle flotation is fundamental to achieving a significant and selective separation. Conventional flotation processes are not suitable to treat these particles because of their low collision efficiency. This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. In this sense, this study assesses the effect of current density and pH on bubble size in a binary electroflotation cell. An increase in the bubble generation rate was reported with an increase in current density. In addition, at acid pH values, the size of oxygen bubbles increased and conversely decreased at basic pH values; this may be due to the electrostatic attraction between the oxygen bubbles and the anode resulting in a greater nucleation time. An opposite trend was observed with the hydrogen bubbles. These results are in agreement with their electrokinetic studies, which reported that at acid conditions the bubble surface may be positively charged for both the hydrogen and the oxygen bubbles. Finally the bubble size was slightly affected by the electrolyte concentration, resulting in smaller diameter bubbles at higher concentrations.

Jan 1, 2016

By Dmitriy Makarov

The paper presents the modeling and analysis of oxidation of pyrite copper-zinc ore samples from the Letnee, Yaman-Kasy and Valentorskoye deposits. It is found, that the oxidized samples contain copper and zinc sulfates that are leached under the sample and water contact. It is shown, that sulfide floatability is decreased by the longer-term oxidation.We advise to improve nonferrous metals recovery by joint leaching and ultrasonic treatment of oxidized compounds. Study of the geotechnological processes of non-ferrous metal extraction, on the basis of two copper-zinc ore deposits shows, that heap leaching is of little use for the ores of the Letnee deposit. Leaching results for the Yaman-Kasy ore showed more promise.

Sep 1, 2012