Search Documents

By R. M. BUCHANAN

The segment of Canadian industry based on smelting of alum in um and manufacture of consumer products is based entirely on imported alumina and bauxite. In the absence of Canadian bauxite deposits, consideration of anorthosite, a less desirable aluminous rock, is being undertaken as one alternative in maintaining assurance of supply. Anorthosites in Canada cover many thousands of square kilometres of the Precambrian Shield. Although compositions vary widely among Canadian anorthosites, many appear to exceed the specified minimum of 25% A I 20 3 in bodies containing more than the required JOO million tonnes. A lthough most Canadian anorthosites are of Precambrian age, one located in British Columbia has been identified as being Middle _Cretaceous.

Jan 1, 1984

By Thomas V. Falkie, Robert Stefanko

Recently The Wall Street Journal featured a series of articles titled "The Dirty Work-Brutal, Mindless Labor Remains a Daily Reality for Millions in The US.-Mining Coal, Shoveling Slag, Gutting Hogs Pays Bills But Can Drain Spirit, Hope." The article was devoted to describing how tough and dangerous is mining (and some other jobs) and how rough life is for miners and their families. Similarly during the past few years some psychiatrists and sociologists have devoted increased attention to the attitudes and life styles of miners. Unfortunately most of their approaches have been neither scientific nor objective, and very little good clinical research has been done on the subject.

Jan 1, 1971

By C. C. Popoff

The growth of the aluminum-smelting industry in the Pacific Northwest, resulting from national defense requirements, emphasized a need for local sources of alumina to supplement the alumina production shipped from the East. Because supplies of foreign bauxite were being interrupted and our domestic bauxite reserves were inadequate, it was necessary to expedite the investigation of other possible sources of alumina during World War II. A program of investigation of high-alumina clay deposits in the Northwest was carried out jointly by the Federal Geological Survey and the Federal Bureau of Mines. As part of this program the Cowlitz clay deposits near Castle Rock, Wash., were explored by the Bureau of Mines in 1942-43. These deposits are near railroads, tide-water, and Bonneville Power Administration lines and within 22 to 100 miles of 4 aluminum-reduction plants.

Jan 1, 1955

By G. R. Strimbeck

This is a report on experimental work on development of a gasification process operating at near atmospheric pressures and using finely pulverized coal entrained in oxygen and steam. The gasifier was designed by The Babcock and Wilcox Co. in cooperation with engineers of the Bureau of Mines Morgantown station. The test work discussed in this report covers the first 34 tests made in the pilot plant in which a strongly coking Sewickley-bed coal, ground to either 70 or 90 percent through a 200-mesh screen, was used.

Jan 1, 1954

By Michael Weaver, Dale Ramsey

Description of Project: The National Gateway Clearance Initiative is an improvement program to achieve a minimum of 21 feet of vertical clearance along CSX Transportation Inc’s (CSX) rail corridor so that double-stacked intermodal railcars can be transported between mid-Atlantic states and their ports to midwest markets.

Jan 1, 2014

By Arthur S. Dwight

THE professional career of Thomas Septimus Austin, who died at El Paso, Tex., August 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., December 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Conn., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-office in Leadville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germanic bears the honorable distinction of being one of the first of the large " custom " lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smelting practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

By M. J. Marcinkowski, K. S. Raghavan, A. S. Sastri

A detailed transmission electron microscopy investigation was carried out in connection with a manganese Hadfield Steel. At small plastic strains, numerous individual intrinsic stacking faults are observed. With increased plastic deformation, the stacking faults thicken into twin lamellae which in turn subdivide the original austenite matrix into smaller domains. The twin boundaries act as strong barriers to subsequent dislocation motion and is in a sense equivalent to grain refinement. It is this "grain refinement" which is believed to be the cause of the very high work hardening rates in the Hadfield Steels. In many cases, especially where an hcp phase is the stable one at low temperatures, the stacking fault energy in fcc metals and alloys decreases with decreasing temperature.' Since stacking faults of the intrinsic type are precursors of both twins as well as the hexagonal close packed structure, both of these entities should become more frequent as the temperature of a fcc crystal is lowered. In the case of the twin, there is no chemical driving force for its formation and it is generally necessary to provide the required driving force by an applied stress, i.e., strain energy. In the case of the hcp structure the transformation from the fcc modification can occur spontaneously (marten-sitically) since a decrease in chemical energy does in fact occur; however, an applied stress will provide an even greater driving force toward complete transformation. Since the transformation products mentioned above occur in an inhomogeneous manner throughout the crystal and since these can act as potential barriers to further plastic deformation2 marked strengthening effects can be anticipated. Also because metal and alloy strenghening is in general proportional to the shear modulus, these effects should be greatest in steels of the austenitic type (y), i.e., the fcc types. Perhaps the two most important steels in this category are the austenitic stainless steels and the Hadfield manganese steels. Both may be quenched from elevated temperatures so as to retain the austenitic states characteristic of those temperatures. The effect of subsequent deformation at lower tem- peratures has a profound effect on the stress-strain curves of these alloys. In particular Fig. 1 shows the compressive stress-strain curves obtained with an 18-8 stainless steel which was quenched from 1850°C after annealing for 1 hr so as to produce all y. As the temperature is lowered, the work hardening rate increases markedly. Although some hcp or c mar-tensite can be generated by plastic deformation as the temperature is lowered,~ it is believed to be a transition phase4 and most of the martensite produced is of the bcc or a variety.3 It is this stress induced martensite which gives rise to the very low initial work hardening at 77°K as can be seen in the stress-strain curve in Fig. 1. Similar low initial work hardening rates have been observed in the stress induced Ni-Ti martensites.5 Fig. 2 shows that an even more rapid rate of work hardening occurs in the Hadfield steels treated in the same way as that described for the 18-8 stainless steels a; the temperature is lowered. It is this ability to work harden to such high stress levels that makes the Hadfield steels particularly suitable for armor plate and heavy construction equipment. However, unlike the case of Fig. 1, no initial low rate of work hardening is observed in any of the curves in Fig. 2. Thus the stress induced formation of any low energy martensite phase in any significant quantity must be ruled out. This observation is in accord with the X-ray findings of Otte.~ On the other hand, small quantities of the E phase have been observed by other investigators using transmission electron microscopy (TEM) above Even more significant was the fact that large numbers of deformation twins were observed in the deformed Hadfield steels,678 which were postulated to be one of the reasons for the high work hardening ability of this class of steels.8 It is the purpose in what follows to discuss a series of experimental observations pertaining to the stress induced transformation in a Hadfield steel and to formulate a dislocation mechanism which adequately accounts for the observed results. EXPERIMENTAL PROCEDURE The stainless steel used to obtain the curves shown in Fig. 1 was of the AISI Type 303 containing approximately 18.0 pct Cr and 8 pct Ni. On the other hand, the Hadfield manganese steel used to obtain the curves shown in Fig. 2 contained between 1.00 to 1.25 pct and 11.5 to 13.5 pct Mn. In all cases the samples were in the form of compression cylinders 0.220 in. in diam and 0.370 in. long. Prior to testing the samples were annealed for a hr at 1050°C and rapidly quenched into a brine solution. This treatment was sufficient to preserve the y phase for subsequent testing at lower temperatures. All samples were compressed in an Instron testing machine using a cross head speed of 0.02 in.

Jan 1, 1970

By Artem Dolotov, Alexander Ter-Oranesyants, Saveliy Kaplan, Boris Axenov, Vasiliy Kovalev, Valeriy Tsyplakov, Konstantin Grigorjev, Nikolai Vorob’ev-Desyatovskii

The issues of double refractory gold ores pressure oxidation were considered. It was demonstrated that along with chloride autoclave preg-robbing which has been studied there are other negative external and intra-autoclave processes resulting in gold losses. It was found that an ingress of even low concentrations of NaCN, ferrum(II) and ferrum(III) cyanide complexes, as well as thiocyanate compounds into the autoclave leads to decrease of gold recovery during further cyanidation in a "carbon in leach" process (CIL). Admixtures depressing recovery of gold can get into the autoclave together with water in the result of industrial accidents or due to peculiarities of recirculation of industrial water used for feed pulp preparation or with quench-water used for process temperature maintenance. In contrast to a chloride preg-robbing which occurs only at pressure oxidation of double refractory gold ores, cyanide preg-robbing starts in the autoclave feeding tank (so-called «upper» preg-robbing). Possible causes of cyanide autoclave preg-robbing and requirements to the quality of water supplied to autoclaving were discussed.

Jan 1, 2014

By Leslie H. Sharp, Martin J. Gavin

Those of the oil-shale operators in this country who are sincerely attempting to make a real industry out of oil-shale developments, are anxious to obtain fundamental data on the retorting of oil-shale; particularly as regards the effect of certain variable factors in the process of retorting on the quantity and quality of products yielded from oil shales when they are subjected to destructive distillation. From careful examination of a con siderable number of suggested processes for treating oil shales and the con flicting ideas on which they are designed, it seems probable that accurate information of a fundamental nature is highly essential to the successful establishment of an oil-shale industry in this country. . Accordingly, the United States Bureau of Mines, in cooperation with the State of Colorado, is undertaking to furnish some definite and impartial information of this type through investigations now under way at the University of Colorado, Boulder, Colo. A retort for the distillation of oil from oil shale has been designed and installed, together with the necessary auxiliary equipment for controlling and determining variable factors of distillation, and for recovering and de termining the quantity and quality of the products yielded from the shales. The retort is of such a nature that conditions of retorting can be accurately . and completely controlled, and varied at will. It is not designed as a com mercial retort, but only for research purposes. A testing laboratory with equipment necessary for the examination of the shales, physically and chemic ally, and the products yielded by them, has also been fitted up . The material used in the investigations is oil shale obtained from the DeBeque, Colorado, shale field. It yields on distillation in the Bureau of Mines testing apparatus, about 42 gallons of oil to the ton, and is there fore a fairly representative sample of the shales that probably will be first worked in Colorado. The shale used will be as uniform as possible in character and oil yield and will all be obtained from the same seam at the same point, in order to avoid the introduction of unnecessary variable factors in the tests and to render results strictly comparable •

Jul 1, 1920

By P. Schumacher, M. Fein

"INTRODUCTION Newmont’s Twin Creeks operation, part of its Nevada operations, produces gold from two large open pit mines. Mined ore is processed at one of three on-site facilities: a refractory mill with two autoclaves, an oxide mill and heap leaching facilities. Twin Creeks also processes various off-site sourced concentrates and ore including high grade underground ore from the Turquoise Ridge joint venture with Barrick Gold Corporation. This paper discusses Twin Creeks’ strategic mine planning process which is part of an in-depth continuous improvement program called “Full Potential.” The process involves cost analysis, phase design validations, life-of-mine production scheduling optimization, mill blending strategy and stockpile management. Through this Full Potential strategic planning, Twin Creeks is creating significant value by increasing near term free cash flow and life of mine net present value (“NPV”) and achieving cost reductions. TWIN CREEKS OPERATION Twin Creeks is one of the major gold producers in Newmont’s Nevada operations (see Figure 1, 2 and 3). Located approximately 15 miles north of Golconda, Twin Creeks produced approximately 28 % of the Nevada operation’s 2013 gold production of 1.8 million ounces (Newmont 2014). The production included Turquoise Ridge sourced gold ore from the joint venture (75% Barrick Gold Corporation, 25% Newmont).At Twin Creeks, there are two large open pits, named Mega Pit and Vista Pit (see Figure 4, 5 and 6). There are 3 to 5 phases in Mega Pit and 2 to 5 phases in Vista Pit depending on the gold price assumption. There is also an underground exploration project at the bottom of the Vista Pit. Twin Creeks produces gold from a variety of ore types requiring different processing techniques depending on economic and metallurgical characteristics. To ensure the best use of processing assets, engineering and processing groups at Twin Creeks utilize a Mixed Integer Linear Programming (“MILP”) model to guide the flow of mine sequences and material routing to various process facilities (Kawahata, Schumacher and Hufford 2013)."

Jan 1, 2015

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock formed by the consolidation of clay, mud and (or) silt. Government and legislative programs The U.S. Environmental Protection Agency (EPA) invited industry to nominate representatives to a review panel that will help the EPA develop rules to regulate air toxics from the production of brick and structural clay products. The EPA was required to establish a review panel because these regulations will significantly affect small businesses. The regulation of air toxics falls under the Clean Air Act.

Jan 1, 2010

By A. Noble

"Froth flotation circuits are widely used throughout the mineral processing industry for the concentration of fine particles. It had been estimated that nearly 2 Gt (2.2 billion st) of ores are treated globally each year using this versatile separation process (Fuerstenau, 1999). Due to the high feed tonnage, a large economic incentive exists for flotation plant operators to optimize the performance of this critical processing circuit. Prior to the 1950s, the optimization of flotation circuits primarily involved the manual adjustment of operating variables based on visual observation and sporadic sampling (Lynch, Harbort and Nelson, 2010). During the next several decades, however, the advent of improved on-line instrumentation coupled with the rapid development of high-speed microprocessors allowed the industry to develop more advanced control systems that could quickly adjust operational parameters in response to disturbances in ore characteristics and plant flows. These early online controls typically involved feedback loops designed to stabilize cell performance through the automatic manipulation of process variables such as pulp levels, gas rates and chemical dosages. The set-points for these controllers were often set by plant operators based on one or more operator objectives, such as maximizing throughput, recovery or grade. More recently, these regulatory controllers have been interfaced with high-level data display and management systems that provide operators with the ability to better optimize flotation plant performance based on mathematical models and rule-based algorithms (Greet, 2010).While tremendous strides have been made during the past several decades, even the most modern flotation plants are still faced with the long-standing question: “What are we trying to optimize?” From an operator perspective, some common responses include “Maximize tonnage of saleable concentrate” or “Maximize metals recovery at a customer-specified market grade.” These replies may or may not reflect those of management, who often focus on economic goals such as “Maximize profits for each operational unit” or “Maximize rate of return for all corporate assets.” Unfortunately, these high-level objective statements do not always translate well into practice due to the disconnect between plant operating protocols and product value. Attempts have been made by industry to overcome this issue using various types of optimization routines such as linear programming or other optimization engines. While this approach does have some merit, these blind routines require considerable input data and interpretational expertise and provide little or no fundamental insight that can be used to drive improvements in concentrator performance."

Feb 1, 2017

By K. Howard Poulsen

Shear zones are tabular tructures which tend to occur either discordantly within, or concordantly along the margins of, competent rock masse uch as plutons, sill or flows. They contain deformed equivalents of their host rock and are common sites for gold mineralization localized in tructure oriented y tematically relative to the shear zones and internal linear fabric. Apan from genetic implications, hear zone analysis proves useful in exploration for this type of deposit because the zones are generally wider and more continuous than associated mineralization and because there is an element of predictability to mineralization geometry (i.e. vein orientation. plunge).

Jan 1, 1986

By Guy Reed, Russell Frith, Kent Mctyer

"Coal pillar design has historically been based on assigning a design factor of safety (FoS) or stability factor (SF) to coal pillars according to their estimated strength and the assumed overburden load acting on them. Acceptable FoS VALUES (have been assigned based on past mining experience, and at least one methodology includes the determination of a statistical link between FoS and probability of failure (PoF).The role of the pillar width-to-height (w/h) ratio has long been established as having a material influence on both the strength of a coal pillar and its potential mode of failure. However, there has been significant professional disagreement on using both FoS and w/h ratio as part of a combined pillar system stability criterion, as compared to using FoS in isolation. The argument is that, as w/h ratio is intrinsic to pillar strength, which, in tum, is intrinsic to FoS, it makes no sense to include w/h ratio twice in the stability assessment. At face value, this logic is sound.However, this paper will argue that there is a valid technical reason to bring w/h ratio into system stability criteria (other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness.When overburden stiffness is bought into pillar system stability considerations, two issues emerge. The first is the width-to-depth (W/H) ratio of the panel, in particular whether it is sub-critical or super-critical from a surface subsidence perspective. As a minimum, this directly relates to the accuracy of the pillar loading assumption of full tributary area loading. The second relates to a reevaluation of pillar FoS based on whether the pillar is in an elastic or non-elastic (i.e., post-yield) state in its as-designed condition, as relevant to maintaining overburden stiffness at the highest possible level.The significance of the model presented is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism without negatively affecting safety is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community."

Jan 1, 2016

By LUDWIG VOGELSTEIN

WE are indebted to Mr. Barbour for his valuable contribution to the literature on copper statistics; it is to my knowledge the only intelligent attempt to throw light on a much misunderstood subject. If I should appear to criticize some of his findings and arguments, I do not want to leave the impression that I do not appreciate the article; I think Mr. Barbour has been painstaking, and even where one might not agree with his conclusions, he has opened our eyes and stimulated us in our search for the truth.' It might be well to define the term "secondary copper" and to make a few remarks about the origin and the reasons for the variation of the supply. Mr. Barbour has touched on these points, but not sufficiently to make them clear to those not in the business.

Jan 1, 1931

By Bryan Bet

Retaining wall systems of soldier pile ground anchors (SPGAs) have been used for many decades to stabilize landslide activity. Due to successful use of these walls to address slope instability on the California state highway system, their use has expanded to include larger, more complex landslide mitigations. The increase in size and scope of SPGA wall applications, combined with more stringent seismic design standards, have created new and unique challenges for design and construction. Constructability issues are revealing themselves in real time in Northern California, where the California Department of Transportation (Caltrans) recently completed two large SPGA wall projects on state highways: the Peregrine Slide Project in inland Mendocino County, and the Westport Slide Complex located along coastal Highway 1. Each presented unique construction challenges that needed to be overcome quickly to make the projects successful. This article highlights some construction difficulties encountered on these projects, in greater depth, than what I covered last summer at DFI's S3: Slopes, Slides and Stabiliza- tion conference in San Francisco. Also covered are what steps were taken to overcome these difficulties, and mitigation advice for future wall designs. Specifically, ground anchor installation interference, ground anchor elongation variance, and difficulties with large diameter ground anchor drilled holes will be discussed.

Jul 1, 2022

By A. D. Ramirez, L. E. Gutierrez, M. A. Garces

"Scarcity of freshwater in mining operations in arid zones in different parts of the world has led to the mining companies to think about using seawater as an alternative source in mineral processing operations. Examples of this situation are Minera Centinela (AMSA) and Minera Sierra Gorda (KGHM), both plants located in northern Chile. Previous studies showed that molybdenite flotation is depressed at high pH values in seawater as a result of the action of hydroxy-complexes of magnesium and calcium that attach to the faces of the molybdenite particles, reducing its hydrophobicity and as a result flotation recovery. In this work, a study of the interactions between molybdenite and kaolinite is presented. The effect of sodium hexametaphosphate (SHMP) dispersant on the recovery of molybdenite in the presence of kaolinite is studied in different aqueous media and it is correlated with induction time data. The results allow to conclude that kaolinite has a stronger depressing effect on molybdenite in seawater compared to its effect in freshwater. Magnesium and calcium are the cations that have the strongest effect in enhancing the interactions between molybdenite and kaolinite. SHMP reduces the negative effect of kaolinite on the floatability of molybdenite both in seawater and freshwater. The induction time data correlate well with the micro-flotation results.INTRODUCTION The need for water in mining processes in arid and semi-arid zones has led to the search for new alternatives for this resource, among which seawater has gained an important space. In Chile, most of the mining operations are located in the northern part of the country, an area that has limited availability of freshwater for the processing of copper and molybdenum sulfides (Castro and Laskowski, 2011, Castro et al., 2012 a). Seawater is an aqueous solution with high concentrations of ions such as Na+, K+, Mg2+, Ca2+, So42-, Cl-, and other less concentrated species which generate important effects in the flotation process as they modify the properties of the solid/liquid, and liquid/gas interfaces, and also increase the consumption of some important reagents used to depress pyrite such as lime. It has also been proposed that flotation of copper sulfides is negatively affected in seawater because of the reduction of oxygen solubility compared to freshwater (Millero et al., 2002; Duan and Sun, 2003). In contrast, it has been shown that the presence of ions in solution in the process of flotation of natural hydrophobic resources improve recovery as result of the compression of the electric double layer (Laskowski, 1974; Klassen and Mokrousov, 1963, Laskowski and Castro, 2008."

Jan 1, 2018

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By Robin J. Batterham

Alumina demand is steadily climbing around the world and is likely to continue to do so for many years. In such a commodity industry, the question arises as to what effort should be expended on innovation, given that for an individual company, the drivers of change are cost and quality as the market demand is essentially assured. This is of course a long-term view. The current conditions are less attractive. In this presentation, we review the broad issues that are considered targets for collaborative development by the industry as recently updated in the alumina industry roadmap published by the International Aluminium Institute in 2010. While they cover areas such as ?mine rehabilitation, residue management and use, alumina production from high sulfur bauxite, bauxite beneficiation, energy efficiency and alternative technologies for alkali and alumina recovery from bauxite residues,? it must be remembered that each refinery is different in terms of the feed material and the circumstances of waste disposal. Of particular interest is the more competitive area of breakthrough technologies. In the presentation, we will consider a range of opportunities that could transform the industry, from relatively near term possibilities such as bauxite activation through possibilities to eliminate crystallization as currently practiced to complete alternatives, such as the use of hyperaccumulating plants. Against this optimism, some of the realities that hold back breakthrough innovation will be presented for discussion.

Sep 1, 2012

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982