Search Documents

By R. B. Sudderth

The recovery of copper by various combinations of processes centered around liquid ion exchange has certainly been accepted as a technically superior entity when compared to the widely applied classical method of cementation. While the technical aspect of liquid ion exchange processes has received much attention and acclaim through actual operating data, in particular the ease of handling solutions, percentage recovery, reduction of pollution, etc., the corresponding economic data has either gone unpublished or has been held confidential. Much of this economic data has now been made available for publication; and with this data, we at General Mills Chemicals, Inc., will attempt to present an accurate economic analysis of some liquid ion exchange plants and an economic comparison between these plants and the typical cementation facility.

Jan 1, 1974

By M. Piard

The scarcity of literature referring to mines in the Rockies has compelled the writer to co-ordinate information and advice taken at the very source. Help was gladly given by active inspectors and mine bosses. Although the field is unimportant at the present time, due to its distance from markets for raw coal, it is quite worthy of the attention it is receiving from two continents; for, with the commercial synthesis of liquid fuels, it would become the largest fuel laboratory in the world, provided, of course, that freight cost drops to a low comparative level. As explained below, there are no obstacles to economical and safe operation under anything like the typical outcrop shown in Figure 1. Although coal dust is probably more dangerous in the Rockies than anywhere else, the damp outcrops afford means of control. The abundant gas may be bled to the open air, and the rigid roof will settle gradually under a wide span of opened outcropping. The Panel Retreating Wall The Measures: Coal measures having an attitude similar to that shown in cross-section in Figure x are characteristic of the active coalfield on the Alberta side of the Rockies, and they are also found on large tracts of undeveloped land west of the divide. The small anticlines, not shown in the cross-section, do not affect the progress of a pillar line, provided their crests are connected to the atmosphere by drainage bore-holes.

Jan 1, 1928

By Lori A. Simpson

Mission Bay is a 300-acre reclaimed site in San Francisco, California, that is currently being redeveloped. Plans include new neighborhoods, parks, a new University of California, San Francisco, research and development campus, a biotechnology campus, and commercial office buildings. New infrastructure is being constructed throughout the site, consisting of utilities, pump stations, and roadways. Previously, Mission Bay was a part of the San Francisco Bay. Reclamation of the shallow bay coincided with the booming development in San Francisco in the 1880s and continued through 1920. Subsurface conditions are extremely variable throughout the site. The stratigraphy generally consists of 5 to 45 feet of fill, up to 140 feet of weak, compressible clay (?Bay Mud?), dense sand, stiff clay, and bedrock of the Franciscan Complex that has been encountered 5 to 210 feet below the ground surface (bgs). Geotechnical issues related to these subsurface conditions include liquefaction, lateral spreading, settlement, and adequate foundation support. This paper presents case studies of the geotechnical aspects of design and construction of several buildings in Mission Bay, highlighting the similarities and variability in the subsurface conditions and the different conclusions and solutions developed for each project. The case studies will include: 1) a building supported on steel H-piles where the depth to bearing varies from about 70 feet bgs in one half of the site to 165 feet bgs in the other half; 2) a building supported on precast, prestressed, concrete piles bearing in a thick, very dense sand layer; 3) a building with over 100 feet of Bay Mud supported on 120- to 180-foot-long PCPS concrete piles driven to bedrock adjacent to buildings supported on steel H-piles driven to bedrock; and 4) sites where auger pressure grouted displacement piles (APGD) and Tubex piles were installed. Case studies will include results of pile driving analyzer (PDA) testing and static pile loads tests, where performed.

Jan 1, 2006

The new field of environmental investiga tions introduces new problems of ethics, res- ponsibility, conflict of interest and technical procedures. Such investigations involve four elements: developer, consultant, approving authority and the public. It is essential that the consultant provide technical competence, speed and efficiency, impartiality and credibi- lity. Despite allegations to the contrary, it is not in the consultant's own best interest to omit, ignore or obscure significant adverse en vironmental impacts.

Jan 1, 1975

By R. Binning

"Economic high density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.Mineral reclamation system design by theoretical formulas is almost impossible because solids composition, ie. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted pumping to relatively dilute slurries whereas it is usually preferred, because of economic considerations to reclaim as high a concentration as possible.At Toyo/De-Velde Corp. we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions.MATERIAL RECLAMATION & PIPELINE INJECTIONTo minimize fluid usage and increase material reclamation efficiency we designed a submersible dredge mixing pump that uses most of its energy to pick up material from rest, mix it with fluid into a highly concentrated slurry then push it firmly into a pipeline.Where material is too compacted to be mined by the standard submersible mixer pump, auxiliary high torque self contained submersible excavators can be fitted around the periphery of the mixer pump. This is to facilitate excavation and break up of the compacted material into a slurry.High flexibility of this system can be achieved by combining the many equipment variations available into the most efficient format to fit individual site requirements.Whatever combination of equipment is selected, torque is nullified by counter rotating excavators against each other. This increases effective excavator/material bite torque but also allows mixer/excavator rig suspension by cable for deep water material recovery."

Jan 1, 1985

By Alhondra de los Santos, Jesús L. Valenzuela, Jose R. Parga

"The present study evaluated the feasibility of using iron species generated by electrocoagulation (EC) as an adsorbent for removal As(III/As(V) from aqueous media. The full potential of EC was evident in that more than 99 percent of arsenic was removed without addition of chemical reagents. The adsorbent iron-species generated by EC was characterized by Chemical Analyses, X-Ray Diffraction and Scanning Electron Microscopy. The experimental data were correlated by employing a Langmuir adsorption isotherm. Thermodynamic parameters such as ?H o , ?S o and ?Go were calculated. The adsorption process was found to be exothermic and spontaneous.1. IntroductionArsenic contamination in potable water supplies is a serious health problem in many countries around the world. Groundwater arsenic contamination in La Comarca Lagunera Mexico was first reported 30 years ago [1]. Arsenic concentration has been found in well water from several communities ranging from 0.25 to 1.0 ppm. The elevated concentration of arsenic in water, above that originating from natural sources, has been attributed to the use of organoarsenical pesticides in the cotton fields and also to the millions of tons of waste slag generated at a local lead smelter [1]. The main arsenic species present in natural waters are arsenate ions 3- 4 AsO (oxidation state V) and arsenic ions H3AsO3, - 2 3 H AsO and 2- 3 HAsO oxidation state III). However, As(V) ions are most prevalent in oxygenated water while As(III) is found for anaerobic conditions, such as in well water or in groundwater. Conventional methods of arsenic removal rely on chemical-based treatment with lime, alum coagulation, iron coagulation and chemical oxidation. Other processes used with varying degrees of success include adsorption onto activated carbon, reverse osmosis, nanofiltration, manganese dioxide, magnetite and ionexchange resins [1-3]. These conventional processes generate a considerable quantity of secondary hazardous waste such as solid sludge, which also pose serious environmental problems. These drawbacks have forced various industries to search for effective, alternative treatment technologies for arsenic with a preference for electrochemical methods."

Jan 1, 2008

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1995

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company's computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002

Systematic ICPES (Inductively coupled plasma emmission spectrometry) analysis of magnetic concentrates from drainage samples has been used to discriminate concentrates dominated by magnetite from those dominated by pisolites, presumably maghemite-rich. In addition, a set of spurious zinc enhancements was recognised and explained with the help of mineralogical data, and systematically isolated using chromium as a Discriminator.

Jan 1, 1987

Lake Superior Iron Ore Association, 3100 East 45th St , Cleveland, Ohio W L Tinker, Secretary This Association does not issue scientific technical bulletins, strictly speaking, but statements, etc , are published containing information of interest to mining engineers and geologists To show the type of information published, mention may be made of material issued in 1931: 1 Directory of mine operators and statistical data. 2 A bulletin, Distribution of Lake Superior iron ores, also Eastern and foreign ore 3 A booklet, Analyses of Lake Superior iron ores, season 1931 These publications, or information on others may be had by addressing the above

Jan 1, 1933

By J. Mantilla, J. Calizaya, J. Frisancho

"La mina Tantahuatay; es un deposito epitermal de alta sulfuración Au-Ag, en perforaciones recientes de extensión por sulfuros, se ha determinado zonas de Skarn al NE del tajo Tantahuatay 2, ubicado políticamente Chugur, Cajamarca, Perú. Los trabajos de perforación 2016, nos han permitido reconocer nuevos cuerpos mineralizados asociados a zonas de Skarn, con leyes de (0.30 g/t Au y 0.4% Cu), emplazados en las formaciones Chulec (calizas), Inca (sedimentos), Farrat (cuarcitas). Los ensamble de alteración analizados son Yeso, Clorita, Epidota, Paragonita, algunos de estos minerales poseen una concentración anómala de REE. Indicativos de una gradación sistema alta sulfuración a Skarn."

May 1, 2008

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By Y. Özçelik

Rocks show a variety of engineering and physical properties that affect typical quarry operation such as diamond wire cutting in the marble quarry. The physical and mechanical properties of rocks depend on their mineralogical and petrographical characteristics. The purpose of this study is to investigate the effects of mineralogical and petrographical properties of a rock, such as grain size and mineral content, and how these affect the wearing of diamond bead and cutting rate in a diamond wire cutting operation in a marble quarry. Statistical analysis is used to carry out the study. Three different rock types were examined, namely, hard rock (andesite) and softer rocks like limestone and marble. The study revealed that the mineralogical and petrographical properties of the rocks, such as percentage of quartz, biotite, plagioclase, matrix minerals, and opaque minerals, are important. In addition, the grain size of quartz and plagioclase in andesitic rocks and calcite grain size for carbonate rocks significantly influenced the wear rate and cutting rate in diamond wire cutting operations.

Jan 1, 2005

By Jin Zigang

In China there are more than 30 coal fields menaced by karst-confined water. In the north and east of China there are many collieries which mine coal seams of the Carboniferous and Permian Systems, which are above the Ordovician limestone (general thickness is 500-600 meters). Ordovician limestone is full of karst fissures, contains a lot of water under high pressure (15-65 kg/cm2) near the commercial coal seams (20-80 meters), the water easily infiltrates the thin lime- stone at the point of the structure crevice, so water-irruptions from the floor are the main source of water-related disasters in these coal fields. According to the statistics there were more than 300 accidents of all kinds of water-irruptions from the floor in these fields since the beginning of their development. It is of great significance in developing coal production in the eastern part of China to solve the problem of safe mining of the seams menaced by the karst-confined water of the Ordovician limestone. The research on this subject consists of three parts: (1) investigating the geological structure and hydrogeological conditions of each mine of the mining area; (2) researching the mechanism of water-irruptions from the floor and proposing reliable methods to predict and monitor; (3) improving the mining system and proposing a mining plan with safety precautions against water-caused accidents. The chief task is to research the mechanisms involved and to discover the causes and conditions of the phenomenon. The authors have obtained some findings on this subject in the last five years, making use of the comprehensive observation and research system, which will be discussed under three headings.

Jan 1, 1984

By E. W. Sawyer

Attapulgite is a magnesium aluminosilicate clay mineral which exhibits unique, processing-enhanceable physical and chemical properties that are related to its current commercial uses. Properties of commercial interest are gelling, absorption, adsorption, binding, acid neutralization and many others. Major industrial applications are: (1) absorption by heat treated grades utilized in industrial oil and grease absorbents and in agricultural pesticide carriers; (2) gelling of aqueous liquid products by colloidal grades for stabilization and viscosity control in salt water drilling fluids, suspension fertilizers, liquid animal feed supplements, paints and tape joint compounds; (3) adsorption by heat treated varieties for the removal of catalysts, color bodies and other polar compounds from hydrocarbon streams; (4) gelling of organic liquids by colloidal attapulgite/surfactant blends in oil-type paints, fibrated and nonfibrated asphaltic coatings and mastic compositions, and (5) the binding of feeds and molecular sieve sorpents with colloidal type attapulgite products. These applications and other less common uses and potential uses will be discussed along with, the necessary selective mining and plant processing features related to each property and application.

Jan 1, 1986

By J. B. Clemmer

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgC03), usually is associated with lime-stone (CaCO3) and dolomite (MgC03 CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amor-phous) forms.2 The more common crystal-line mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories.

Jan 1, 1940

By R. D. Sharpe

Gypsum wallboard manufacturers in the United States shipped 3.18 billion m2 (34.2 billion sq ft) of wall-board products during 2004 versus 2.93 billion m2 (31.5billion sq ft) in 2003. Following a historic high production of gypsum wallboard products in 1999, production decreased in 2000. But it has steadily increased during2001 through 2004. Wallboard production in the United States increased about 8.6 percent in 2004 from 2003. Following several years of a “building boom” of new wallboard plants and the expansion of the manufacturing capacity of several existing plants, 2004 was a relatively quiet year. However, several new plants and capacity expansions were announced or are in progress during 2004.

Jan 1, 2005

Orange Free State Branch Minutes of a Committee Meeting held in the Boardroom of Western Holdings on Thursday, IIth October, 1973, at 5.00 p.m. Present Messrs E. T. Wilson (in the Chair), E. Dunstan, W. B. Evans, C. J. Isaac, C. Mostert, N. Shand, R. Williams, and G. Young.

Jan 2, 1974