Search Documents

By F. A. V. Guimarães, A. M. Costa

"The moisture in sintering is a very important parameter for the performance of the process. It allows that the granulation takes pace in an efficient way making the water bridges between the bigger particles used as nucleus and the finer particles that perform the coating of those coarse particles. The formation of the micro pellets is extremely important to prevent loss in permeability of the bed in the sintering grate, avoiding excessive fuel consumption and producing a quality sinter. The aim of this project is to use some of the methodologies for determine the saturation degree on ores and coal to determine the optimal moisture for sintering. In the sinter pot grate series, 3 to 4 assays in a series of 10 are required to determine the optimal moisture for the process. The saturation degree curve test has shown that is really viable to use this technique to skip those tests and go directly to the series to determine productivity and the coke / anthracite consumption. In an industrial scale can be used to adjust the water addition in the conventional mixing methods used in the sintering plants to increase productivity in the process.INTRODUCTION Sintering Sintering is a high temperature agglomeration process in which iron ore fines are partially melted and bonded together using fluxes and a source of fuel, usually coke breeze. The agglomerated product, sinter, has improved metallurgical properties making it an ideal ferrous burden that enable the passage of hot gases in the iron-making blast furnace. The sintering process is normally carried out over three basic stages: granulation, ignition/sintering, and product sizing. In the granulation stage, iron ore fines (usually a blend of selected ores), sinter return fines, fluxes and fuel, and are mixed with water and micro-pelletised in a drum or disc before being introduced in the main granulation circuit. (Wang, Teng, & Wang, 2017)."

Jan 1, 2018

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

By Brian R. Green

Resin-in-pulp (RIP) technology has been developed for recovery of gold. It is now time to look forward to the potential for application of the technology to other situations. Some cases have been identified and have merited preliminary testwork. Four examples, which illustrate the potential of RIP, are dealt with in this paper. These include removal of metal-cyanides from pulps, recovery of manganese that is difficult to wash from filter cakes, recovery of nickel from low grade pulps, and recovery of zinc from process residues. The discussion includes descriptions of the problems, factors that affect the choice of resin, and factors that will affect the economics of the process.

Jan 1, 1998

The Electrolytic Refining and Smelting Company of Australia Limited (ER&S) operates a copper smelting and refining plant and is situated close to the heart of the highly industrialised area of Port Kembla. In March, 1982 the Company entered into an undertaking with the State Pollution Control Commission (SPCC) to monitor ambient levels of sulphur dioxide (S02) gases present in the atmosphere in the surrounding urban area. Despite the use of a 200 metre high stack for dispersal of the smelter waste gas stream at ER&S, two local suburbs, Warrawong and Primbee were experiencing on occasions high ambient concentrations of S02 resulting in discomfort to local residents. In late March 1982, ER&S installed a highly advanced S02 monitoring system to continuously monitor the levels at Warrawong. The system was extended to include S02 monitoring at Primbee in November 1982, and further extended in June 1983, to include an input of meteorological data. Initially the system was designed to monitor and react to high concentrations of S02 at either of the two monitoring stations. Currently however, refinement is taking place to allow a predictive nature to be built into the system such that it not only reacts to an adverse situation but can predict weather patterns likely to cause high concentrations and thus avoid these events. The entire system is still undergoing a growth and development period, however the results obtained to date are pleasing to both the Company and the SPCC.

Jan 1, 1984

By E. Lammer

"Underground mining processes are dangerous. The design of mining equipment, which is able to cope with the hostile underground environment, is a challenge for all machine manufacturers. Presupposition for realizing the vision of SANDVIK for zero harm for working with SANDVIK equipment is the installation of the appropriate processes. Into the product engineering and product development processes of Sandvik Mining and Construction, a specific "Product Safety Process" has been integrated, where all safety related activities like identification of all life cycle hazards, risk management and safety verification / validation are planned, performed and documented. Product safety shall be „designed into" the products. Therefore, specific research activities have been started, to address the safety and health related topics for the development and for the engineering of SANDVIK mining machines."

Jan 1, 2011

By Markus A. Reuter, Yongxiang Yang, James R. Post

The packed coke bed in the lower part of an iron making blast furnace, the dead man, dissolves slowly in a pool of hot metal, which is tapped regularly. The coke particles of the dead man not only exhibit a size distribution, but also their size distribution is non-uniform throughout the dead man and as a result, the porosity of the dead man is non-uniform. This causes the flow of hot metal through the dead man to be irregular and non-uniform, bringing about channelling in the coke bed. Channelling is detrimental to the refractory lining life of the hearth of a blast furnace. Using population balance modelling and a porosity model it is possible to keep track of the local changes in size distribution and bed porosity during dissolution of coke particles. Numerical simulations show that carbon dissolution from a packed coke bed (with particles which exhibit a size distribution) increases the average porosity, decreases the mean particle size and changes the size distribution to a distribution with a smaller size range. Influence of the type of initial size distribution (mean, variance) is investigated. The calculated changes in porosity are used to dynamically adapt the flow and the mass transfer (kinetics) during calculations. This approach provides the possibility to implement dynamic porosity calculations for CFD applications, and thus simulate the results of various coke types and particle size distributions on dissolution and flow behaviour.

Jan 1, 2003

By Zhiyang Long, Ruiling Xiao

"A mine shaft is one main development method of establishing access in an underground mine. The construction technology of the mine shaft sinking is complicated and large equipment setup on surface and in the mine shaft. The paper briefly reviews a single-line operation method, parallel operation method and mixed operation method as well as the features of the one operation method with the excavation, lining and installation. The special construction technology mainly would include ground freezing methods, full diameter shaft drilling methods, caisson methods, grouting technology and concrete curtain methods as well as other methods. The paper summarizes the shaft sinking numbers and effects by the special construction methods during different periods. The paper states the shaft sinking conditions and the each created record conditions in the coal, metallurgy, non-ferrous metal, hydropower, highway, railway, nonmetallic and other industries. The paper has a prediction on the shaft sinking requirements and development tendency in the future for China.INTRODUCTIONA mine shaft is one main development method of access in an underground mine. In recent years in China the new shaft mines represent 45% of the total number of new mines. With the development of new mining area under construction and the development of deeper mines, the ratio of the mine shaft as access for underground mines will increase. The construction technology of the mine shaft engineering will be complicated, the operation site footprint will be small and the working environment will be more difficult. The mine shaft sinking operation will often be varied by the geological conditions and affected by underground water inflows, seam gas outbursts, geothermal and other natural conditions. The safe construction of the mine shaft sinking will be challenged by all these conditions. Although the mine shaft engineering will only be about 5% of the total mine roadway engineering, the mine shaft construction period often will take over 40% of the total mine construction period. With the progress of modernized mine production technology and the construction of a high production and high efficient mine, the mine transportation roadways mostly would be set in the seam and the engineered amount of the mine rock roadways reduced year by year could cause more prominent long extensions of the mine shaft construction period. Therefore, in order to speed up the construction, to shorten the mine construction period and to realize the investment benefits as early as possible, the technical level of the mine shaft sinking should firstly be improved and the construction speed of the mine shaft engineering and sinking should be speeded up, which would have important significant benefits."

Jan 1, 2019

By E. E. Maust

The literature on the activation of sphalerite for flotation by short¬chain xanthates leaves unanswered the question of whether a compact surface film of activator sulfide is necessary or merely sufficient for high flotation recoveries. Studies by Guarnaschelli and Plaksin indicate that xanthate adsorption and flotation of sphalerite are increased with increasing hole/ electron ratio. These results, and the known acceptorlike behavior of many heavy-metal impurities in zinc sulfide, suggest that activation may result from a traditional semiconductor doping effect at the surface. Using the theory of chemisorption states on ionic crystals as developed by Levine and Mark, the Bureau of Mines has carried out A calculation to estimate the surface-state energies of various metals when they are substituted at zinc sites on (110) sphalerite surfaces. Based on a simple Madelung-Born treatment of ionic solids, the calculation indicates that many of the metals known to activate sphalerite for subsequent flotation have lower surface-state energies than nonactivators. The results of these calculations are discussed from the standpoint of consistency with the proposed activation mechanism and observed flotation results. The satisfactory agreement obtained is taken to be support for the proposed mechanism, and further elaboration of a surface-doping model is attempted.

Jan 1, 1976

By L. W. Burger

The need to establish and harmonise methodologies to quantify air emissions, atmospheric dispersion and the consequences of air pollutants (especially hexavalent chromium) from the ferrochrome industry became important aspects with the increasing demands for comprehensive impact assessments. The paper includes a synthesis of current knowledge on the following aspects: ? Locally and internationally accepted methodologies for the quantification of chromium emissions, including sampling methods and emission factors; ? A compilation of recognised and accepted air quality sampling and laboratory analysing techniques; and, ? Dispersion modelling and impact assessment tools. Depositing and removing materials from the chromium ore stockpile and wind erosion of exposed stockpiles result in mainly chromite emissions unlikely to contain significant amounts of hexavalent chromium. Pre-treatment processes such as drying, crushing and screening also produces chromium emissions, but mainly as trivalent chromium. The smelting of chromium is the major source of chromium emissions - open furnaces have the highest uncontrolled chromium emissions, followed by semi-closed and closed furnaces, respectively. Based on the current knowledge on emission rates, interim emission factors for particulate, total chromium and hexavalent chromium releases are provided. Ambient sampling and analytical methods to determine environmental exposure of the general public require that hexavalent chromium needs to be quantified in very low concentrations. Suggested sampling and analytical methods for both source characterisation and ambient monitoring are provided. The selection between dispersion models needs to be based on the size of the modelling domain and the complexity of the terrain. The discussion on dispersion models includes the US EPA?s Industrial Source Complex Model (Version 3), the AERMET/AERMOD suite of models and the CALMET/CALPUFF suite of models. Guidelines are also proposed for environmental exposure assessments including cancer and non-cancer health effects.

Jan 1, 2004

By Yi Luo

The severity of disturbances caused by longwall mining subsidence to various residential structures can be re¬duced. The success of such mitigation efforts depends on accurate subsidence prediction, correct assessments of the subsidence influences, and careful design and implementa¬tion of the proper mitigation measures. This paper presents the systematic approach involved in the subsidence mitiga¬tion efforts with a case demonstration.

Jan 1, 2003

By L. Chunpongtong

One of the challenges of mine planning is to determine the most cost-effective replacement time for aging equipment. The lifespan of equipment, such as haul trucks and shovels, deployed in mining operations varies due to the nature of the material and ground conditions in which it operates. For engineering economists dealing with aging equipment, the options become an economic trade-off between higher maintenance cost versus the cost of new equipment. The discount rate plays a significant role in this decision; the higher the rate, the longer the economically optimal lifespan. Therefore, the ultimate question is: ?How can the relationship between the discount rate and the economically optimal lifespan be expressed mathematically??

Aug 1, 2013

By Horace Pops, L. L. Isaacs

SOLID-STATE transformations at low temperatures are frequently studied by optical metallography. Greninger and ooradian' and Hull and Gar-wood2 have examined the martensitic-type transformations in 0-phase Cu-Zn alloys during continuous cooling below room temperature. The lowest range of temperatures in the apparatus described by these investigators is limited to approximately 110°K. Present studies of reversible first-order phase transitions near liquid-helium temperatures have necessitated the design of a new cold-stage cryo-stat for optical metallography. The features of interest of this instrument are as follows: a) temperatures down to 4.Z°K are obtainable; b) the specimen is always under vacuum, thereby avoiding the condensation of moisture; c) specimens can be rapidly cooled or heated at varying rates, thus permitting studies of transformation hysteresis. Fig. 1 shows the details of the cryostat. All major parts are made of type 304 stainless steel. Both helium and nitrogen cans are Heliarc-welded to the helium filling tube, permitting the use of a common shielding can. Hence, the over-all weight and the area of the evacuated surface are mini- mized. The copper sample holder is screwed into the bottom of the helium can. To assure good thermal contact between the sample holder and the refrigerant, an indium ribbon is placed on the threads

Jan 1, 1964

By G. H. Miller

With the recent advances which have been made in science and technology and the increased use of mathematics in this area, the question of the best mathematics courses for a mining engineer to take is of major importance. The question becomes even more difficult to answer due to the recent increase in the number of different mathematics courses in the last two decades offered by the mathematics departments. Therefore, the National Study of Mathematics Requirements for Scientists and Engineers (NSMRSE) was designed to provide some answers to these questions. Approximately 10,000 scientists and engineers were selected for the Study, These individuals were placed in two categories: (1) The Awards Group, recipients of national honors or awards and those recommended by the members of the Board of Advisors as having national and international reputations in their areas of specialization and (2) The Abstracts Group, persons exceptionally productive in their research, based on the number of journal articles listed in the last five years in the Engineering Index, Scientific and Technological Aerospace Reports, Chemical Abstracts, Biological Abstracts, and the Physics Abstracts. The NSMRSE Course Recommendation Form and the Instruction and Course Content Sheet were constructed with the aid of the Board of Advisors and other consultants. For the Study, 40 courses were selected by the mathematical consultants. In order to make sure that the basic content of the mathematics courses was the same for all respondents, a brief resume of each of the 40 courses was given. The NSMRSE Course Recommendation Form consisted of seven sections. These sections were as follows: Section 1, 38 different specializations; Section 2, orientation of work (applied through theoretical); Section 3, highest degree obtained; Section 4, place of employment (academic, nonacademic); Section 5, administrative capacity (administrative or nonadministrative); Section 6, age groups (five-year intervals). Section 7 contained the 40 courses which were to be marked according to five categories: (1) Course Length, 3 to 36 weeks; (2) Applied-Theoretical Orientation, a five-point scale; (3) Course Level, freshman through graduate; (4) Knowledge of Course; and (5) Use of Course Content in Work. The Analysis The report of the data is based on the replies received from 44 mining engineers. This group was part of the Awards and Abstracts Group for all engineers. The resume of the recommended courses is reported in quintiles (upper fifth to lower fifth), since recommendations of this kind are not precise. The results of the Study are based on recommendations of the most active research men in engineering in the U.S. today; therefore, the reader should realize that these course recommendations represent an upper bound of mathematics requirements for the Ph.D. in both undergraduate and graduate work. Conclusions and Recommendations 1) Mining engineering students who plan to be active research specialists should take all those courses which are "very highly recommended" (80-10070) and "highly recommended" (60-79.9%). Those courses in the upper two quintiles and recommended by most mining engineers are: first-year calculus, third-semester calculus, elementary differential equations, applied statistics, and machine computation. Courses of "moderate recommendation" (40-59.9%) are: vectors, intermediate ordinary differential equations, the first course in partial differential equations, elementary probability, and linear programming. 2) The great majority of mining engineers indicated that they prefer a course which is concerned primarily with applications. Only the standard courses such as first-year college mathematics, calculus, differential equations, and advanced calculus received a recommendation for 50% theory and 50% practice. Therefore, all mathematics courses given to mining engineers should contain many applications and little theory. Engineers in both the applied and the combination (ap-plied-theoretical) groups indicated a definite need for applications in all courses. 3) In general, recommendations were for mathematics courses to be given for short intervals of time such as 3, 6, or 12 weeks. Only the standard courses mentioned previously received the usual one-semester or one-year recommendation. Therefore, it is of value to combine several related courses into a one or two-semester course so that the mining engineering student could acquire important mathematical knowledge at an early date in order to prepare him for his research. 4) There was little use for the newer courses in modern mathematics such as the functional analysis sequence, the modern algebra sequence, and the group theory sequence. In addition, there were uniformly very low recommendations (0-19.9%) for multilinear algebra, complex variables, mathematical logic, special functions, integral equations, approximation theory, analytic mechanics, integral transforms, and geometric algebra. Therefore, these courses should be given a low priority. 5a) Comparisons among mining engineers with different backgrounds showed that the combination ap-plied-theoretical group recommended more mathematics than the applied group. 5b) There was little difference in recommendations between the administrative group and the nonadminis-trative group. 5c) Analysis of age groups showed that those in the lower age groups gave significantly higher recommendations to courses such as the first course in partial dif-

Jan 1, 1971

By E. Van Den Neste

A concise historical review is given of the Overpelt plant and the general principles of zinc hydrometallurgy are briefly outlined, together with a description of the new electrolytic zinc plant ore roasting process and, more particularly, the original Overpelt roasting process. A detailed description of the flowsheet of the zinc electrowinning plant, .with an annual capacity of 100,000 t, successfully put into operation in May 1974, is given. The treatment of the residues is performed following the goethite process ; the purification is continuous in two steps; the tank house is equipped with cells containing jumbo cathodes; the handling and stripping of the cathodes is fully mechanized. Concluding the description, some metallurgical and other features of the project are explained in detail.

Jan 1, 1977

By J J. McNee and, J Crusius, T F. Pedersen

The use of water covers is a globally-applied method for minimising acid rock drainage (ARD) and metal leaching. Although the subaqueous disposal of potentially acid-generating materials has been shown to effectively limit ARD, under certain scenarios, metal remobilisation can occur at circum-neutral pH. The following paper presents data from four case studies in which metal mobility from submerged mine waste resulted in degradation to water quality in the overlying water cover. Subcentimetre resolution profiling of dissolved constituents across the tailings-water interface (dialysis arrays), in conjunction with mineralogical information, were used to elucidate the controls governing metal mobility. The data illustrate four pathways of metal remobilisation, including: the release of zinc via the oxidative remineralisation of metal-rich organics at the tailings-water interface; enhanced remobilisation of arsenic as a result of anthropogenic eutrophication; the release of copper resulting from the pH-driven dissolution of treatment sludges; and the release of radium from uranium mill tailings due to the dissolution of radiobarite [(Ra,Ba)SO4] by sulfate-reducing bacteria. The results highlight the conclusion that the chemical stability of submerged tailings reflects both: the solid-phase characteristics of the tailings material; and the physical, chemical and biological characteristics of the depositional environment. In particular, the data illustrate that rigorous characterisation of both the waste solids and receiving environment must be performed in order to assess their compatibility. The results have relevance to the management of tailings repositories including constructed impoundments, pit lakes and natural lakes.

Jan 1, 2003

By M Lemieux, R Mason

The SABREX blast modeling program was introduced to I.O.C.C.'s Carol Lake Iron Ore Project in December 1987. As part of CIL's Technical Services, SABREX was used to implement an optimization program designed to analyze and introduce various grades of MAGNAFRAC at a constant pattern while maintaining acceptable blast results.

Jan 1, 1989

By Alan Morris

Impingement attack, as one of the types of corrosion suffered by condenser tubes, has been given a prominent place in corrosion literature of recent years. It has been reproduced and studied in carefully controlled laboratory tests. Much has been learned of its mechanism, and of the effects of variables such as temperature, amount of air, size of bubble and water velocity. Incidentally the technical public has been given comparisons between the behavior of some few metals under various conditions of impingement attack. The tests recorded here were undertaken in an effort to find at least some sort of qualitative answer to questions which arose occasionally as to the relative resistance of various alloys to impingement attack, and which could not be answered by reference to the literature. The final decision to start work on the problem was influenced in large measure by the nature of the water available in this particular place. The mill of the Bridgeport Brass Co. is located on the Pequonnock River at Bridgeport, Conn., within two miles of its mouth. The water is much like many other estuarine sources which are used in condensers, and which cause particularly severe corrosion. It seemed a most suitable water to use in such tests. As the work progressed an important seasonal variation was noted. The purpose of this note is to record this seasonal effect. The results of individual tests are given only incidentally. Impingement Tests Early in 1929 the apparatus was built. The samples were disks of 1-in. dia., cut from sheet metal. They were eleaned with fine emery cloth and set in holders, as shown in Fig. 1. A stream of water pumped directly from the river impinged on the surface of the sample. Compressed air was injected into the water stream through an air duct. Water pressure was maintained at about 35 Ib. per sq. in. and air was controlled by a needle valve. Velocity of

Jan 1, 1932

The Nominating Committee for Institute Officers in 1953, John R. Suman, chairman, completed its work at the Annual Meeting in February, and has made its report to the Board of Directors. The President-Elect in 1953 serves as President in 1954. The ticket follows: For President-Elect and Director, Leo F. Reinartz; for Vice-President and Director, A. B. Kinzel and Lloyd E. Elkins; for Director, Hjalmar W. Johnson, Philip Kraft, Gail Moulton, Edwin L. Oliver, Philip Wilson, and Elmer Isern. Mr. Reinartz is a vice-president of the Armco Steel Corp., Middletown, Ohio. As required by the bylaws, brief biographical sketches of the nominees will be published in the July issues of the journals.

Jan 1, 1952

By W. I. Duvall

A brief review of the resonant frequency and ultrasonic pulse methods for obtaining elastic constants of rock samples shows that the equations for an iso-tropic elastic solid commonly used to calculate Young's modulus, modulus of rigidity and Poisson's ratio can result in appreciable error if the rock is even slightly anisotropic. Consideration of the equations that relate bar velocities and free medium velocities to elastic constants for orthotropic, transversely isotropic and isotropic solids shows that a combination of the two methods can be used to determine average elastic constants for a single sample of rock. The determination of elastic constants in different directions requires a large number of tests on oriented samples. The use of both the resonant frequency and ultrasonic pulse methods is recommended so that the determination of both Young's modulus and modulus of rigidity is independent of the determination of Poisson's ratio. The dynamic elastic constants of rock can be determined in the laboratory from measurements on small samples which may be in the form of right circular cylinders (diamond drill core). Either the resonant frequency6 or ultrasonic pulse method1 can be used to determine the longitudinal and shear velocities in the same specimen. The resonant frequency method provides a measure of the longitudinal bar velocity, V,, and the torsional bar velocity Vt; whereas the ultrasonic pulse method provides a measure of the free medium longitudinal velocity, Vp, and the free medium shear velocity, V, . The elastic constants (Young's modulus E, modulus of rigidity G, and Poisson's ratio v) are calculated from the density of the specimen, p, and one of the pairs of velocities by means of equations from isotropic elastic theory. For the resonant frequency method the equations are: It should be noted that Eq. 5 is derived from Eq. 4 and 6 and the relation between the elastic constants for an isotropic solid as given by the first part of Eq. 3. The in situ determination of dynamic elastic constants is accomplished by generating a complex seismic pulse in the rock and measuring the arrival times for the longitudinal and shear phases of the pulse at two distant points.5 From these travel times and the distance of the travel path both Vp and Vs are determined. The density of the rock is determined from samples in the laboratory, and Eq. 4 to 6 are used to calculate the elastic constants. These three methods involve the assumption of isotropy and perfect elasticity, and require the use of the relation v = (E/2G) - 1, which holds only if the elastic constants are the same in at least two directions. The calculation of v by means of Eq. 3 introduces considerable error, as a 1% error in V, and V, results in a 20% error in v. If frequencies for samples with a length-to-diameter ratio greater than four and a length greater than 8 in. are measured carefully, the experimental error can be kept to 1%. However, it is not unreasonable to expect that the variation in Vb and Vt with direction may exceed 1%. Thus, for even a small percentage of anisotropy the use of Eq. 3 can result in considerable error in v. The calculation of v by Eq. 5 also involves some uncertainty as a 1% error in Vs and Vp can result in a 6% error in v. By means of the pulse method both

Jan 1, 1965

By C. L. O?Brian

Note: The figures quoted and used herein have been collected and furnished by the Dominion Bureau of Statistics. Without the help and willing co-operation of the officials of the Burreau, this study would not have been possible. Introductory and General Coal has one unique quality that distinguishes it from other minerals, one that is too, often forgotten. This is the quality of ubiquity. No other single mineral supplies such a wide and varied range of human requirements nor, up to the present, is there any indication of a rival in this regard. There is, consequently, reason for individual study of each of the major portions of the overall market for coa1. The provision of heat for our homes is a necessity of life in our Northern climate and the largest single source of this heat is coal. It is intended to present here a factual survey of the use ?of coal in home heating throughout Canada and the effect of these requirements upon the production of coal and the development of this phase of the mineral industry. The coals used for house heating in Canada fall into two more or less distinct classes, the very low volatile fuels such as anthracite and including coke, and the bituminous coals, including the sub-bituminous and lignite types. The bituminous coals are, of course, consumed in very large quantity by industry and the railways and are the most important type both in tonnage and in respect to the area supplied. Canada consumes annually for all purposes some 4,400,000 tons of anthracite, 4,300,000 tons of coke exclusive of Petroleum coke, and some 40,000,000 tons of bituminous coals. This is a fair measure of the relative importance to the overall economy although it will be seen later that the concentration of the household use of anthracite and coke into one area does create a considerable problem.

Jan 1, 1951