Search Documents

By W. H. Adams

During the years when Americans were most active in investigations of the many substances containing nitrogen or ammonia, viz.: 1869 to 1875, my connection with certain chemical industries led me to experiments in the direction of the recovery of wastes from coal-gases. I take from my notes such memoranda as I think will be of interest, in the hope that some benefit may be derived therefrom by engineers at present attempting to utilize the waste products from coke-oven and blast-furnace gases. An examination of the conditions governing the manufacture of gas along the Atlantic seaboard, and an intimate knowledge of the mine-products used by the different large works, naturally led me at first to consider the well-known foreign methods of concentrating the available soluble salts in a modicum of water. The result was sufficiently promising to warrant a full line of experiments. At that time, no attention seemed to have been paid to the values of " gas-liquors." Nearly every gas-works in the United States wasted its wash-water in the sewers. The nitrogen in bituminous coals varies in quantity from 0.75 to 1.50 per cent. of the total weight. In the process of distillation in

Jan 1, 1887

By Donald L. Stewart, Ken Overfield, Edward M. Williams

"Recent increases in energy cost have lead to a renewed focus on energy efficiency during aluminum melting operations to reduce fuel usage. The goals of a batch melting operation are to melt the charge using the minimum required energy, to melt the metal to the required temperature within the required timeframe, and to avoid generating unwanted contaminants by overheating the charge.The heat transfer efficiency of a conventional hydrocarbon fired aluminum melting furnace varies over the course of the melt cycle, depending on the conditions in the furnace. The purpose of this work was to develop a method of determining the transient heat transfer efficiency throughout the furnace cycle and to take advantage of this knowledge to optimize the melting process through furnace controls and proper production operations. This furnace survey methodology has been developed and used to evaluate a number of furnaces.Description of a Typical Batch Melting Furnace CycleA typical batch melting furnace cycle will consist of three stages:1. Charging – Solid metal charged through an open roof, solid or molten charged through an open door, and/or molten poured through a furnace blister2. Melting – From the time the door or roof is closed and the burners are turned to high fire until the charge is all liquid and has reached a temperature suitable for alloying (typically ~1350 °F / 730 °C)3. Holding – From the end of the melting stage until transfer or casting is completeIn some cases, further charging can take place after the melting cycle has started. This can happen when the entire solid charge will not fit in the furnace in one load, or if additional molten metal is added while the charge is melting. The bulk of the energy used in the melter is consumed during the melting cycle. The thermodynamic minimum energy requirements for melting pure aluminum are:• Energy required to heat pure aluminum from room temperature to the melting point at 1220°F (660°C) is 288 BTU/lb (670 kJ/kg)• Energy required to change state of pure aluminum from solid to liquid (heat of fusion) is 171 BTU/lb (397 kJ/kg)• Energy required to heat molten from melting point at 1220°F (660°C) to 1350°F (730°C) is 36 BTU/lb (83 kJ/kg)• Total energy required to melt a solid charge from room temperature to 1350°F (730°C ) is 495 BTU/lb (1151 kJ/kg)"

Jan 1, 2009

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985

By Alfred H. Brand

New York City contains extensive deep deposits of glacial lake varved silt and clay, often overlain by organic soil. An 18 story building was proposed for Manhattan's upper East Side in one such area where bedrock is approximately 200 ft deep. Various pile and caisson alternatives were considered extending through the glacial lake soil to rock, but all proved beyond the project budget. Laboratory testing showed that the glacial lake deposits were preconsolidated. A test pile program using auger cast piles bearing in the glacial lake deposits proved that such piles could safely carry a load of 60 tons per unit. The auger cast pile scheme was estimated to be more economical than a deep pile alternative. A further benefit was that the vibration-free pile installation procedure posed less risk to adjacent structures which had been founded at shallow depth in fill above organic deposits and were stressed and cracked due to prior settlement. The project was designed with the anticipation that the glacial soils beneath the tips of the piles would produce a building settlement of 1 to 2 inches. The building was constructed in 2001 and 2002. It has been completed and is now occupied. Settlement data show that the building is performing as predicted. The auger cast pile scheme founded in a compressible stratum has proven to be successful and is a very unusual foundation alternative.

Jan 1, 2003

By F. R. A. Jorgenson

The ignition of chalcopyrite and pyrite was studied using laminar flow furnace and thermal analysis techniques which were supported by XRD and optical microscopic examination of the products. In air, chalcopyrite and pyrite ignited at temperatures of 400-500'C and 500-600?C respectively. The phase assemblages predicted from thermodynamic analyses were compared with those found by experiment, and the onset of ignition was correlated against changes in the phase compositions. Pyrite and chalcopyrite ignited when pyrrhotite and intermediate solid solution formed thus opening up the structure and allowing ready access of oxygen.

Jan 1, 1989

By Jessica Egan, Daniel Hodouin, Mohammed Reza Khalezi, Steve Bellec, Claude Bazin, Carl Duchesne

"A model for gold leaching was developed and implemented into a simulator. The simulator uses a description of the ore that is based on the mineral composition and precious metal content. The model accounts for the distribution of minerals and precious metals through the size intervals. An ore texture model based on precious metals and minerals grain sizes within the ore is used to predict the exposed surface of the species in the various size intervals. A model is proposed to predict the rate of dissolution of any species dissolution using the exposed surface, particle size, cyanide and oxygen concentrations, temperature, pH and agitation. The flow of slurry through a leaching tank is modelled using a parallel arrangement of perfect mixers to simulate a bypass and a Cholette-Cloutier mixer model. The simulator can be used for circuit optimization but was developed to provide an environment for learning the basic concepts of process analysis methods. Examples are given to illustrate the application of the simulator for planning tracer tests and sampling campaigns.INTRODUCTIONThe constant pressure to improve the operation of processes that are already close to optimum imposes to plant engineers to be aware of the available process analysis tools and to be able to use them to assess process operation and make a diagnosis to possible problems. Some of these tools are:•,Sampling the streams of a process;•,Data reconciliation;•,Analysis of mixing in reactors;•,Estimation of rate parameters;•,Optimal tuning and flow sheet modification;•,Automatic control and real time optimization.Although some of these tools are part of the curriculum of many university engineering programs, the students are not exposed to actual process analysis problems. In addition the complexity of the ore dressing processes compounded with unavoidable measurement errors and plant disturbances can discourage many motivated engineers. These factors often lead to an incomplete valorization of the collected data and a poor return on the investment associated with the sampling, testing and analysis of the samples.Simulators are readily available for process optimization (Yalcin and Shang, 2006) by allowing:•,The simulation of various flow sheet configurations;•,The simulation of a change of operating conditions;•,The simulation of various control strategies;•,The training of plant operators.However few simulators have been developed with the objective of providing an environment for training plant engineers and technicians to the use of tools for process analysis and optimisation."

Jan 1, 2008

By John Taylor

"The Highvale Mine in Alberta is owned by TransAlta Utilities Corpora/ion and operated by Mana/fa Coal Lid. It is the largest coal mine in Canada and in 1982 supplied 8.6 million 1onnes of sub-bituminous ""B"" coal to TransAlta's Sundance Ceneraling Plan/. Annual produclion is scheduled to increase in 1983 when the firs/ unit of the new Keephil/s Generating Plant comes on stream and is expec/ed to exceed 11 million tonnes by 1985 when the second unit is commissioned. Coal is mined from several pits in a multi-seam operation. Comprehensive maintenance, drainage and environmental programs form a major part of the operation.IntroductionThe Highvale Mine is located eighty kilometres west of Edmonton, Alberta on the south shore of Lake Wabamun (Fig. I). The mine is owned by TransAlta Utilities Corporation (T.A.U.) and is operated by Manalta Coal Ltd. In 1982, 8.6 million tonnes of coal were supplied to T.A.U.'s 2100 MW Sundance Generating Plant, making it the largest producing coal mine in Canada. By 1985, with two 375 MW units on line at T.A. U .'s new Keephills Generating Plant, annual production is estimated to exceed eleven million tonnes. The generating plants accept crushed unwashed coal from the mine via the coal handling plant system conveyor belts. The coal is classified as sub-bituminous ""B"" and has an average heating capacity of 18.6 MJ I kg.HistoryPrior to 1943 only small scale mining took place in the Highvale area. Between 1943 and 1961 two strip mining companies, Mount Royal Collieries and Continental Collieries operated on the present mine site. Both operations excavated coal along the south shore of Lake Wabamun."

Jan 1, 1985

By Kyung-Ho Park

The smelting leaching process is known as one of the most favorite methods for the processing of deep-sea manganese nodules because of its smaller environmental impact and easiness of manganese recovery. The sulphuric acid pressure leaching of the matte prepared from deep-sea manganese nodules was studied to dissolve the valuable metals. Almost complete dissolution of Cu, Ni, and Co from matte was achieved under the following conditions: leaching temperature 180°C, time 4 hours, PO2 10 kgs/cm2, acid concentration 2.5% (vol/vol), pulp density 5%, ammonium sulphate 40 g/l. Under these conditions the iron concentration of leach liquor was 0.95 g/l. Optimization of leaching parameters was carried out by statistical design of experiments using 23 full factorial matrix. The linear and interaction co-efficients were evaluated for dissolution of metal values and also for iron concentration in leach liquors.

Jan 1, 2003

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993

By Kidd, Robert L.

INASMUCH as galena and sphalerite flotation concentrates are being produced that contain over 95 per cent galena or sphalerite, it is not unreasonable to believe that a flotation concentrate assaying at least 80 per cent of native gold can he secured provided the gold is free. As yet, little if any fundamental information has been published concerning the flotation of free gold either alone or in the presence of sulfides. So far, we are unable to make as complete a separation of gold from sulfide minerals by flotation as is possible in, the separation of one sulfide from another by this method. An introductory study of the flotation of several free gold ores has been made in our Utah laboratories. For this study three general types of gold ores were chosen, namely: (1) Quartzite containing 0.26 oz. gold per ton in which no base metals are present; (2) sulfide ore (2.04 oz. Au; 1.31 oz. AO containing pyrite as the only sulfide present and the gold free; and (3) oxidized ore (1.10 oz. Au; 0.70 oz. Ag) from an oxidized zone of the vein from which sulfide ore (No. 2) was taken; little sulfide iron was present.

Jan 1, 1932

By R. F. Harig

Designing an underground nuclear waste repository is a complex process. Although many decisions are involved before the design is complete, the first three--what the target horizon is, what the underground boundary is, and where the entry point will be located--are important because they establish the basis for the entire repository design. Even more important than these decisions, however, is the data on which the decisions are based. Because the current data are limited, an aggressive data gathering program is needed during the next design phase to augment information about the intricate interplay among all facets of the repository design and the geologic medium in which the proposed repository is to be developed. Although unique to modern engineering enterprises, the challenges involved in designing a repository in the unsaturated zone are within current technology and engineering practices.

Jan 1, 1991

By V. Astucuri

El presente trabajo describe el proceso de extracción de plata de dos muestras de relaves antiguos empleando la cianuración. De acuerdo a este estudio, entre todos los procesos metalúrgicos utilizados para la recuperación de la plata como la tostación sulfatante, amalgamación, flotación, se encontró que la cianuración es un proceso completo ya que puede reemplazar a las anteriores, con excepción de la amalgamación de plata nativa y otras deficiencias. En consecuencia, la cianuración es el método hidrometalúrgico que aprovecha mejor el poder lixiviante de los cianuros alcalinos en soluciones diluídas y extrae la palta de los relaves. Por ello, se supedita a su contenido económico y a los minerales no económicos entre los que se encuentre asociado.

Oct 14, 1980

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on cab air filtration system performance. Factors experimentally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab protection performance. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By Robert Kozicki, Eric Graham, George Wrightson

"IntroductionThe manufacture of Ferro Chromium involves the smelting of various ores and fluxes to produce the metallic product.Slag is inherent in the process. It has a much lower density than the metallic FeCr. Some chrome may be trapped in the slag as either FeCr or Cr203.Previous methods to estimate the slag in the FeCr have revolved around separating the slag and metallic portions by exploiting the differences in density. The downside with that procedure is that material will often contain pieces that are adhered FeCr and slag. The Metallic FeCr may also be completely encapsulated in the slag.An alternative and more precise method involves calculating the slag content based on chemical analysis of Mg and Al. The Mg and Al will be at relatively low levels (less than 0.1 % ) in the Metallic FeCr pieces and considerably higher in the slag (3% or greater). The overall sample will have a proportional amount and is calculated using simultaneous equations with the assumption there is only one kind of slag and one kind ofFeCr present. ""Pure"" slag and ""pure"" FeCr are needed in order to determine the Mg and Al in each. The detemlination of the Mg and Al in the overall sample would then be used to calculate the amount of slag.When the particle size is small, it is difficult to sample and get ""pure"" pieces of the slag and FeCr of sufficient quantity to perform a proper analysis. Often, historic data is used but that is dependent on the source of the FeCr and the materials used in its production. Mg and Al levels in slag can vary between 3% and 20% in different FeCr slags depending on their origin."

Jan 1, 2013

By H. J. Engell, W. Frank, A. Seeger

SWISHER and ~urkdogan' have determined the solubility of oxygen in a iron. They found it to lie between 7 and 10.5 at.-ppm at 881°C. Using earlier work on the permeability of oxygen in bcc iron,' they arrived at the following expression for the diffusion coefficient of oxygen in bcc iron (k = Boltzmann's constant, T = absolute temperature): where The present authors3 have estimated the activation energy QD for the diffusion of oxygen in bcc iron in two different ways from various experimental data.2'4"6 In the first method QD + QS (QS = heat of solution for oxygen in bcc iron in thermodynamic equilibrium with solid FeO) was determined either from data on the reduction of FeO with hydrogen4 or from measurements of the internal oxidation of silicon in a iron.5 Using an estimate of QS from investigations of the oxygen solubility in 6 iron2 (in thermodynamic equilibrium with molten FeO) Q = 0.97 ev or Q~ = 1.06 ev were obtained. From the magnitude of these values it was concluded that oxygen migrates interstitially in bcc iron and that consequently the activation energy QD for diffusion of oxygen has to be identified with the migration energy E~ of the oxygen atoms. Therefore, for a second estimate of QD from the diffusion coefficient of oxygen in 6 iron at 1450" ~,~ we used the theoretical expression:3 (a = length of elementary cube edge, m = mass of interstitially diffusing atom, sM = migration entropy), applicable to diffusion via the octahedral interstices in bcc lattices. Taking sM = 3.8 k (migration entropy of carbon in a iron), one gets Q = 0.90 ev. Hence, in Ref. 3 Q = (0.98 *0.1) ev was proposed as a plausible value for the diffusion energy of oxygen in bcc iron. sM + 9 (9 = solution entropy for oxygen in bcc iron) can be determined from permeability measurements.4 Using the above-mentioned estimate for QS , the following expression for the solubility c (atomic concentration) of oxygen (in thermodynamic equilibrium with solid FeO) in bcc iron was derived: From [4] the solubility of oxygen at 881°C in a iron is calculated to lie between 0.6 and 12 at.-ppm. We see that the solubility determined by Swisher and

Jan 1, 1969

By R. D. Leitch

In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report. ACKNOWLEDGMENTS The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and do others for information received; and to Dr, R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.

Jan 1, 1928

By M. Hokkanen, M. Hagfors

The Finnish Defence Forces has destroyed old and spoilt munitions in open surface mass detonations at Hukkakero fell in municipality of Kittilä, Lapland, since 1988. The technique was learned from Sweden. The destruction camp is organized every year at autumn and it lasts 4-5 weeks. During the disposal period one or two charges are exploded per day. The gross weight of a typical charge varies from 150-250 tons including 15-25 tons of explosives. They mainly consist of TNT, but may also contain smaller amounts of amatol and hexotol. As a booster there have been used 2-3 tons of emulsion explosives.

Jan 1, 2015