Search Documents

By Jeffrey Y. Foley

The Bureau of Mines sampled surface exposures of podiform chromite in the Caribou Mountain-Melozitna ultramafic belt in the Kokrines-Hodzana Highlands, central Alaska. Fieldwork began in 1979 as part of an assessment of the mineral potential of lands adjacent to the trans-Alaska pipeline corridor, for the Bureau of Land Management, and continued through 1981 as a Bureau of Mines investigation. The belt comprises six complexes of which the three closest to the pipeline corridor were investigated. Concentrations of chromite disseminated in dunite host rock make up mineralized intervals ranging in thickness from less than an inch to 5 ft and in grade from 3 to 23 pct chromium. The largest occurrence has an exposed strike length of 80 ft. Bulk surface samples were collected from 10 of these exposures, and beneficiation tests on the samples produced concentrates of metallurgical, refractory, and subindustrial grades. Part I--this report--describes the fieldwork; part II--1C 8916--describes the beneficiation work.

Jan 1, 1983

By K. Himbeault, D. Campbell, N. C. Garisto, D. A. Orava, A. Rosaasen

"The level of scientific knowledge about the effects of contaminants is increasing and changes in environmental monitoring are likely to allow for the assessment of environment effects particularly to the aquatic environment. This paper provides an overview of recent developments in this area which include the environmental effects monitoring program for pulp and paper operations, the assessment of the Aquatic Effects of Mining (AQUAMIN) program, the Aquatic Effects Technology Evaluation (AETE) program, and the review of the federal Metal Mining Liquid Effluent Regulations (MMLER). The paper also provides a look forward at the direction of environmental monitoring of mine projects in Canada. IntroductionEnvironmental monitoring programs provide a wide range of data to environmental management systems, regulatory authorities, and stakeholders. The data obtained are used to demonstrate that operations are in compliance with regulatory environmental protection requirements, and provide the scientific basis for assessing the effectiveness of environmental protection measures. Environmental monitoring requirements for mine projects are established based on the type of operation, site specific issues and concerns, and the requirements of regulators and mine proponents.The level of scientific knowledge regarding the potential effects of contaminants on the receiving environment is increasing, and in particular with regards to the receiving aquatic environment. Regulatory controls regarding the protection of fish, fish habitat, and fishery resources are being reviewed with regards to their adequacy, and the environmental effects monitoring program on the pulp and paper industry is expected to provide useful data relevant to those types of operations. These developments are of interest to mine proponents as it is presently expected that an environment effects monitoring program will be developed specifically for the metal mining industry under a regulated environmental effects monitoring program as part of the Fisheries Act. This paper reviews recent developments in this area, and provides a look forward on the future directions of environmental monitoring programs."

Jan 1, 2000

By H. W. Gillett, E. L. Mack

Prior to 1911 the literature on melting brass by electricity consisted entirely-save for some suggestions made in patent literature but not actually worked out-of a few observations by farseeing men ' on the theoretical advantages of melting brass and other nonferrous alloys in electric furnaces. Roeber was the first to see and clearly state the possible advantages of the electric furnace in brass melting. The same factors tha.t make it desirable to manufacture special steels in the electric furnace rather than in crucibles, he declared, apply to brass as well. He pointed out the possibility of using larger melting units, of eliminating crucible cost, of readily controlling the purity of the product. and of nearly eliminating the loss of zinc. "The replacement of the • old crucible process is sure to come," he said; "perhaps it will come in two years, but it will, necessarily, in ten years .... The inevitable advance along this industrial line will have great influence in the metal world and will also provide, in large cities, a new kind of load for the central station." The years 1905 to 1910 may be termed the purely theoretical period of the development of the electric brass furnace, though the Conley furnace was tried out e:xperimenta.lly about 1910 and a few heats were made in an induction furnace. 2 In December, 1911, the American Chemical Society held a symposium on mineral wastes, at which Bassett s discussed the zinc· losses that attend making brass in fuel-fired furnaces.

Jan 1, 1922

By D. M. Ziebarth

"During the mid to late 1960s, the underground potash industry in Saskatchewan was born. For the next four decades the industry operated at a steady pace, supporting a large part of the world demand, until 2008 when the potash market heightened. Operators were motivated to capitalize on this increased demand, new mines were proposed while existing mines were planning upgrades. Potash Corp. of Saskatchewan (PCS) was one of the major producers planning upgrades to its production facilities quickly, including modifying the existing headframe and shaft at the PCS Cory Site to accommodate a new 1.5-kt/h (1,650-stph) hoisting plant. Upon completion of the project, the innovative operations group continuously reviewed methods to increase production and reduce operating costs, allowing PCS to continue being competitive on the world market.BackgroundPotash production is a major Saskatchewan industry and has played a significant role in the economy for more than 40 years. Production commenced in 1962 when water problems were overcome at the International Minerals and Chemical (IMC) Mine near Esterhazy, Saskatchewan. A surge of development by other companies resulted in 12 companies opening 10 mines by 1970. In 1975, Potash Corp. of Saskatchewan was created by the government of Saskatchewan, and shortly thereafter purchased several mines in Saskatchewan, including the Cory Mine, near Saskatoon.Cory has been in operation since 1968 and is located 12 km (7.5 miles) west of Saskatoon in central Saskatchewan. The mine is located in the center of the world’s largest potash deposit, 1,000 m (3,300 ft) below surface.PCS has embarked on sizable capital expansions of more than CDN$7 billion.The $1.6-billion Cory expansion was expected to raise operational capability of the site to 2.7 Mt/a (3 million stpy), an increase of 1.9 Mt/a (2.1 million stpy). To achieve 2.7 Mt/a (3 million stpy) of finished product and considering the 22.6 percent average production recovery (Potash Corp, 2013), 12 Mt/a (13.2 million stpy) of ore must be hoisted to the surface for processing. To deliver this rate required upgrading of the hoisting plant to 1.5 kt/h (1,650 stph). To accomplish this ambitious challenge, creative thinking, careful planning and a cohesive team was needed to work together to ensure the schedule, budget and most importantly that the work was completed safely (Potash Corp., 2013)."

Apr 1, 2017

By Thomas A. Milne

As part of the broad program to improve the safety of underground coal mines, the Pittsburgh Mining and Safety Research Center sponsored several detailed studies on the inhibition of coal dust-air explosions. The present study was one of these. The goal of the research was to advance the development of improved coal-dust explosion inhibiting agents by determining, on a laboratory scale, the basic chemical processes involved in the inhibition of coal-dust flames by dry-powder agents. B. Our Approach Neither the basic molecular processes involved in coal combustion, nor the molecular mode of action of dry-powder agents, are known with certainty. Our approach, therefore, involved the direct determination, by sampling techniques, of species behavior in small, aerodynamically simple flames. To further aid in separating behavior of coal and dry-powder inhibitors, the latter were studied in CH4-air flames.

Jan 1, 1976

By Wang Xianzheng

For a long period of time, the Chinese Government has been attaching great importance to and supporting the rapid development of the coal industry. Particularly since more than 30 years ago, when China introduced the Reform and Opening-up policy, the reform and development of the Chinese coal industry has witnessed world-recognized achievements. National coal production increased from 618 million tonnes in 1978 to 3.52 billion tonnes in 2011. While China?s coal production accounts for 49.5% of the world?s total, its annual production growth contributes to over 80% of global production growth. China is a country utilizing coal as its main source of energy. As the Chinese Government gives support to the rapid development of new and renewable energy sources, as well as to increased coal utilization efficiency, the ratio of coal in the primary energy consumption mix will gradually decline. However, for a long period of time to come, the total volume of coal demand will keep rising modestly. The Chinese Government has been highly committed to and actively promoting the overall, coordinated and sustainable development model, which puts people first. It has put forward a strategic task to build an ecological civilization, and highlighted its resolve to uphold the basic national policy of resource conservation and environmental protection, with a view to the pursuit of sustainable development. China will incorporate its response to climate change into the national economic and social development program, and take effective measures to lower CO2 emissions 40?45% per unit of GDP in 2020 compared to 2005. At the same time, China will increase the ratio of non-fossil fuels to 15% in the primary energy consumption mix. All of the above factors have raised requirements for the Chinese coal industry, with implications for clear directions, plans and goals for the development of the coal industry.

Aug 1, 2013

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By Shahriar Vahdani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles of highway, including seven bridges, three cut-and-cover tunnels, and an undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles from the San Andreas Fault, which is capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. At the Tennessee Hollow bridge section up to 30 feet of loose sands and soft clays are present. Concerns are raised that standalone drilled piers will experience excessive lateral soil loads from liquefaction-induced lateral spreading pressure resulting in excessive pier head displacement of up to 8 inches. Ground improvement by Cement Deep Soil Mixing (CDSM) is proposed to provide additional foundation stiffness. This paper presents the methodology to: 1) assess the effectiveness of the ground improvement in resisting lateral spreading, and 2) optimize ground improvement design at individual bridge bents based on local site condition. A series of 3-D numerical analyses are conducted and the results show that drilled piers with CDSM ground improvement are capable of withstanding seismic demands from lateral spreading and the lateral pier head displacement is reduced to less than 2 inches. The adopted analytical approach is efficient at modifying design for individual bents and can be considered for future pier foundation design in seismically active areas. IntroductionThe Tennessee Hollow bridge section (Low Viaduct) is an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. As shown on Figure 1, the project site is located about 5.6 miles east of the San Andreas Fault and 12.5 miles west of the Hayward Fault. The Low Viaduct will span over a future wetland habitat subject to tidal fluctuations and potential scouring."

Jan 1, 2014

By C. Dorfling, P. Albertyn

"Hydrometallurgical recovery of metals from printed circuit board waste typically involves multiple leaching stages; conventionally, base metals dissolution by mineral acids is followed by leaching of gold using cyanide or halide based lixiviants. Alternative lixiviants for gold leaching can reduce the potential hazardous nature of operation. The aim of this study was to investigate the feasibility of using thiosulfate as lixiviant for gold leaching from waste printed circuit boards. Batch leaching tests were performed to investigate the effects of thiosulfate concentration (0.1 – 0.2 M), ammonium concentration (0.2 – 0.4 M), pH (9 – 10.5), solids content (25 – 50 g/L), and copper content of the feed material on the gold leaching behavior. The concentrations of metals in liquid samples were determined by means of inductively coupled plasma atomic emission spectroscopy, and high pressure liquid chromatography was used to evaluate thiosulfate degradation/consumption. The ratio of thiosulfate to ammonia was found to have the most significant effect on the extent of gold leaching, with the best gold extraction observed at a ratio of 0.5 mole thiosulfate per mole ammonia. The lower pH range of 9 – 9.5 generally produced better Au leaching, while low copper extraction during the first stage base metal leaching stages has proven to be detrimental to gold leaching from the residue. Thiosulfate degradation/consumption increased and gold extraction decreased with higher residual copper in the feed. An optimum gold extraction of 78.5 % from base metal leach residue was achieved with 0.2 M thiosulfate, 0.4 M ammonia, and 0.02 M cupric ions at 25°C in the pH range 9 – 9.5.INTRODUCTION Background and Aim The recycling of e-waste is becoming increasingly important as it provides certain economic benefits apart from the obvious environmental benefits. Printed circuit boards (PCBs) are found in most forms of e-waste and contain especially high concentrations of base and precious metals. Hydrometallurgical processes are often considered for the recovery of valuable metals from PCBs; these processes normally implement several leaching stages to selectively recover certain metals."

Jan 1, 2018

By R. W. Lowe

1. Reserves are estimated in the Nemo, Sewanee, Wilder, and White Oak beds of Fentress County, Tenn. The Wilder is the only bed being mined commercially and contains the largest known reserves. Eleven lesser known beds are present in the county, but not enough information on them was available for estimating the reserves. 2. Known measured and indicated reserves, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 102 million tons as of January 1, 1955. This total includes 66 million tons in beds 28 inches and more thick.

Jan 1, 1956

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By K. Robertson, K. A. Scalise, K. C. Kocsis, M. B. Teixeira

"Many deep and highly mechanized underground metal mines require cooling. In many cases, appropriate working conditions might be fulfilled by ventilation alone, but some require the implementation of cooling systems. The most common cooling systems are bulk air cooling and localized cooling. These systems are effective, but they use considerable amounts of electricity. Ground source heat pumps (GSHP) can supplement existing cooling and heating systems, while geothermal systems can cool the mines in their entirety if there are significant sources of geothermal energy are present. A major advantage of geothermal and GSHP systems are their renewability, which reduces the carbon footprint of the mine.INTRODUCTIONThe western United States has abundant alternative energy sources including a high potential for geothermal energy. Geothermal utilization is a viable energy alternative that many areas throughout the world have access to because high geothermal potentials are located near areas of volcanic activity such as along plate boundaries, mid-oceanic ridges, rift valleys and hot spots (IRENA, 2017). There is significant potential to use geothermal energy for many applications. With constantly evolving and innovative technologies being developed, an increasing number of geothermal applications are becoming feasible. The western United States is an ideal candidate for alternative energy applications due to the geothermal availability and the emergence of modern technology. This paper investigates the incorporation of renewable methods and the alternative energy possibilities of Barrick Goldstrike, located in northern Eureka County, NV and Rio Tinto/BHP Billiton’s Resolution Copper mine located in Superior, AZ.RENEWABLE SYSTEMSGeothermal SystemsGeothermal temperatures are typically defined as either high or low temperature systems(Shengjun, Huaixian, & Tao, 2011). The high-temperature reservoirs (>220°C / 428°F) are feasible forlarge, commercial production of electricity with dry stream and flash stream systems (Shengjun, Huaixian, & Tao, 2011). Low temperature systems, below 220°C (428°F) (Shengjun, Huaixian, & Tao, 2011), aremuch more difficult to use for energy production. Low-temperature reservoir heat can be harnessedthrough the implementation of a binary cycle plant. The working fluid for a binary cycle plant is eitherorganic (Organic Rankine Cycle (ORC)) or an ammonia-water mixture (Kalina cycle). Organic fluids andammonia-water mixtures have low boiling points that allow for the recovery of heat from low-temperaturesources (Eymel Campos Rodriguez, et al., 2013). The efficiency of the binary cycle plant varies depending upon the fluid, thus the proper selection of the fluid is critical for maximum energy output"

Jan 1, 2019

By Pedro Lilienfeld

This report describes a program whose objective was to develop, design, fabricate and laboratory-test two prototype instruments capable of real-time selective detection and measurement of airborne fibrous-shaped particles. The operation of this fibrous aerosol monitor (FAM) is based on the rotation imparted to the acicular particles by means of a rotating quadrupole electric field of the order of 3000 V/cm. This field induces a dipole charge separation on the fibers and aligns them with the applied field. The selective detection of the fibers is effected by synchronous detection of the resulting modulation of the light scattered from a continuous-wave helium-neon laser beam by the rotating particles. The theory of operation, design of the electric-optical detection configuration and the electronic signal processing method are discussed. By means of a scattering pulse sharpness discrimination technique, fibers whose length exceed a selectable value are detected and their number concentration digitally displayed. Counting times of 1 to 1000 minutes permit the measurement of fiber concentrations between 0.001 and about 30 cm-3. A concentration of the order of one fiber per cubic centimeter can be assessed within a relative standard deviation of 10 percent with a counting period of 10 minutes. The FAM is a portable, battery-powered instrument capable of operating continuously for about 4 hours between battery charges. Preliminary tests with crocidolite and crysotile asbestos as well as with glass fibers were performed in the laboratory and the results indicate good correlation with the standard NIOSH phase contrast microscopy filter counting method.

Jan 1, 1977

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources -limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to deter-mine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By Alexander Fleischanderl

Steel market has become somehow unpredictable and requires quick adjustment in production conditions to survive in the harsh market environment. Steel production is not anymore driven by output records, but by efficient cost reduction measures to remain competitive under strongly varying production conditions. Energy efficient production and flexible raw material scenarios have become decisive factors to succeed and survive in our industry. Such scenarios have to be carefully investigated to be well prepared to adopt production steps continuously. The paper analyses various process opportunities to optimize energy and raw material consumption in the production route. Off-gas treatment systems have still a huge untapped potential to recover energy from the hot waste gases. This is valid for the EAF mini mills as well as for the integrated route. Various examples for waste heat recovery systems including resulting benefits are discussed for the EAF, agglomeration, blast furnace, direct reduction and BOF. New innovative bag-filter systems feature extremely low emission levels at lowest pressure loss and sound emission conditions. Also improved control and automation solutions support the operators to minimize the operation and maintenance costs of their off-gas system. Steelmaking by-products shall not be considered as residues, but as a valuable and cheap raw material source. The paper presents some show cases how to valorize slags as well as utilizing coke and iron oxide fines to increase productivity and minimize raw material cost. A new process for highly flexible converter steelmaking allowing for extraordinary high HBI and scrap rates above 50% and improved yield is discussed and evaluated

Oct 30, 2017

By C. A. Gibbons

AFTER nine years of extremely de- pressed business, marked mostly A with red ink on the balance sheets of most coal companies and with an increasing internal competitive struggle for diminishing markets, somewhat of a change appeared during 1939. Shipments increased and prices generally firmed, giving the coal industry increasing optimism and encouragement for the future. Specifically, it now appears that bituminous coal production for 1939 will approximate 378,000,000 tons, and anthracite production will approximate 47,500,000 tons, bituminous production being around 14 per cent ahead of 1938 and anthracite production 12 per cent better. The curve on p. 31, showing both bituminous and anthracite production, furnished by the bituminous coal division of the Department of the Interior, shows graphically most of the 1939 monthly production and clearly illustrates the increased production.

Jan 1, 1940

By E. Lentilucci, A. Dey, X. Liu, A. Datta, S. Ghosh

The segmentation of quarry blast smoke plumes is a crucial research area that has the potential to enhance safety, environmental monitoring, object detection, and regulatory compliance in the mining industry. Smoke plume segmentation can be used to identify the spatial extent and temporal evolution of smoke plumes generated by the blast. This information can be used to improve the understanding of blast dynamics and optimize blast designs. Furthermore, smoke plume segmentation can assist in identifying potential environmental and health hazards associated with the release of smoke and dust particles into the atmosphere during quarry blasts. However, many current smoke plume segmentation algorithms are designed for segmentation of smoke plumes from fires and are not suitable for segmentation of plumes from quarry blasts. The proposed method in this paper leverages the video frame captured before the blast as a stationary background image, which helps to reduce other confuser objects present in the image along with a selfadaptive clustering method. The color channels of the image are utilized based on the different contrast properties of the smoke, with a self-adaptive gradient compensation applied for edge detection of the smoke plume. This approach offers a novel and effective way to segment smoke in quarry blast analysis, with potential applications in the calculation of noxious gas volume and concentration within the plume. Compared to other algorithms, our method improves accuracy, decreases the false alarm rates, and reduces the overall miss rate. Overall, this paper contributes to the research on smoke plume image segmentation, particularly for quarry blast smoke plumes, which possess unique characteristics that require specialized algorithms for accurate segmentation.

Jan 1, 2024

By B McFadyen, Y Potvin, K Woodward

The Australian Centre for Geomechanics (ACG) held two workshops in 2019—one in Australia and one in Canada—to discuss processes and methods currently used in the mining industry for stope design and reconciliation. In practice, this work strives to optimise stope performance and aims to maximise ore recovery (minimise underbreak), while minimising dilution (overbreak). One of the key findings from the workshops was that current stope design practices, almost exclusively, rely on some versions of the empirical Stability Graph methods developed in 1980s. Although robust and useful at the feasibility study stage, there are a number of inherent shortcomings with this approach. The Stability Graph’s limitations first lie in that it cannot assess underbreak, which is a very important measure of performance. Furthermore, the method doesn’t consider a number of factors which often have a critical influence on stope stability, for example, drilling and blasting or the presence of faults. Given the current industry standard practice, there is a great opportunity to reinvent the stope design process to optimise performance. A finding of the workshops was that every mine quantifies stope performance in terms of volume reconciliation with a focus on dilution and ore losses, and reconciling metal tonnes recovered from the mill. Many mines further investigate stope performance by looking at individual stope faces and the causes for the deviations between the planned stope shape and the measured cavity. Recent research at the ACG has shown that investigating overbreak and underbreak at a higher resolution is a powerful way to identify the root causes of overbreak and underbreak. Finer scale assessment is achieved using an octree analyses, which effectively divides the relevant stope volume into cubes on the scale of a metre and produces many tens of thousands of data points. The octree data structure and subsequent analysis underpins a data-driven stope design methodology. The ACG is currently developing a design approach based on multivariate modelling methods that can account for the many variables that influence stope performance and forecast stope overbreak and underbreak results. Back-analysing stopes based on octree reconciliation results provides a rich database for training the model. Once the model can achieve reliable forecasting of overbreak and underbreak, an interactive drill-and-blast design will allow for the assessment of different firing strategies to optimise stope performance.

Mar 15, 2021

By Lorraine B. Burgin

This study by the Bureau of Mines documents the leadtime required for preliminary and detailed exploration, development of the mine, and construction of beneficiation and support facilities for selected copper deposits in Arizona. The time for major exploration ranged from 1 to 15 years, time for open pit development (or construction) was 1 to 4 years, and time for under- ground development was 4 to 8 years; one underground mine presently being developed may require 12 years to achieve production. Construction of the beneficiation plants required 8 months to just over 2 years. The data are supported by historical facts for each deposit during the leadtime stages from location of claims through exploration, construction, expansion, and leaching. The sequence of development and factors contributing to differences in the time spans are discussed. Histories are detailed for the Miami, Castle Dome, Copper Cities, San Manuel-Kalamazoo, and Twin Buttes properties; briefly summarized are the Pinto Valley, Miami East, Esperanza-Sierrita, Pima, and Mineral Park Properties. Each mining operation had its own pattern of development, and together they present a source of planning information for the development of other properties.

Jan 1, 1976