Search Documents

By L. J. Habegger

This paper considers the potential water quality impacts of future energy scenarios which project an approximate doubling of coal utilization from 1975 to 1985. The major impacts estimated for coal extraction are related to effluents from unregulated activities (reclaimed areas prior to stable vegetation) and pollutants (e.g., metals and ammonia). Where applicable, the EPA effluent guidelines to be in effect by 1983 reduce the impact of individual sources to low levels. For example, total suspended solids and acidic discharges are to be regulated to levels generally below recommended water quality standards for receiving streams. However, implementation of these guidelines, particularly for coal extraction, has not been demonstrated on a wide scale. Water quality is not expected to be a major constraining factor for increasing capacity of coal fired utility and industrial boilers. Water quality control has not been demonstrated on a commercial scale for coal conversion to synfuels, but adequate control technologies appear to be feasible.

Jan 1, 1978

By Green R. E.

The removal of silica from commercial iron oxide concentrates by dissolution with sodium hydroxide was investigated by the Bureau of Mines as a means for producing supergrade concentrates. The effects of strength of solution, temperature, and digestion time on the extraction of silica were evaluated using eight iron oxide concentrates. Silica extraction from the eight concentrates was enhanced by autoclave leaching in the temperature range of 150° to 250° C and varied from 70 to 95 pct depending on the concentrate used. Superconcentrates containing less than 2 pct Si02 and more than 69 pct Fe were made only when magnetite concentrates were leached in the autoclave. The investigation showed that it is not difficult to obtain a supergrade product if the gangue is mainly quartz.

Jan 1, 1973

By Shuie Li, Taibai Li, Tao Hu, Zhongjie Wang, Xiang Ge

As one of the main power sources, lithium-ion batteries (LIBs) will continue to be applied on a large scale in the future market. Commercialized LIBs cathode materials contain various valuable metal elements including Li, Co, and Ni. The development of green and efficient recycling technology is essential. Deep eutectic solvents (DESs) have recently emerged as a new class of green solvents that could potentially be applied for the LIBs recycling industry due to their capability to leach the active materials without the introduction of environmentally hazardous reagents as used in conventional hydrometallurgy process. Considering the rapid progress, a critical review focusing on the progress and fundamentals about the overall efficiency has practical significance for the further advancement of this field. Herein, we briefly introduce the overall process of using DESs for LIBs recycling and specifically focus on the efficiency of each step. Current fundamental understandings and new experimental approaches to enhance the efficiency of the leaching process, the extraction process, and reusability are summarized. We expect this review article to inspire scientists to use DESs as powerful tools for advancing the frontiers of LIBs recycling.

Jul 30, 2022

By C. W. Davis, L. R. Messer

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.' The properties that make fuller's earth useful in the treatment of petroleum products by "percolation1' and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other adsorbent earths.

Jan 1, 1929

By Zainab Nasrullah, MontanaFrank Agyemang, Mehran Sadat, Richard LaDouceur

Rare earth elements (REEs) are valuable for various modern technological applications, including metallurgy, machine building, radio electronics, instrument engineering, nuclear engineering, and manufacturing. The extraction and separa-tion of rare earth elements (REEs) from their complex ores is challenging due to their distinct physical and chemical properties, contributing to their market scarcity. At present, REE recovery utilizes traditional pyro- or hydrometallurgi-cal processes. The overall process in the recovery and sepa-ration of individual elements from complex REE systems suffers from high energy demands and the use of many haz-ardous chemicals that negatively impact the environment. With the growing trend toward a circular economy aim-ing to balance sustainability, efficiency, and environmental impacts, this research is focused on using deep eutectic sol-vents (DESs): a combination of a quaternary salt: Choline Chloride and five organic acids: Oxalic Acid, Urea, and Ethylene Glycol, Lactic acid and Glycerol for the selective leaching of REEs from their complex ore which is proven to be green, selective, non-toxic, biodegradable, and cheap. The effects of different DESs and leaching time on the REE leaching efficiency were determined, and the optimum DES media were found to be Oxaline and Lactic Acid at which a leaching efficiency of 25% and 15% was achieved at 80°C respectively for cerium.

Feb 1, 2025

By John Postle, Maureen Jensen, Marcel Vallee, Bernie Haystead, Dan Hora, Graham Clow

The Committee's proposed standards establish definitions and guidelines for the reporting of Exploration Information, Mineral Resources and Mineral Reserves in Canada and are identified as the "CIM Standards" and referred to as such hereafter in this document. To provide additional clarification to Qualified Persons (QPs), guidelines have been included with the respective definitions. The CIM Standards are applicable to all minerals including industrial minerals, diamonds and other gemstones. Reserve definitions for bitumen, natural gas and oil are not included in these Standards. The CIM Standards are not intended to cover mineral inventory estimates that will be reported to government agencies.

Jan 1, 2001

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels - from mining and processing to the manufacturing of finished products. In 2010, the estimated real GDP of the United States increased by 2.8 percent compared with 2009 and the estimated nominal GDP was about $14.6 trillion (Table 1).Trends in various sectors of the domestic economy are often rejected in mineral production and consumption rates. For instance, continued declines in the construction industry during 2010 were rejected in further reductions in the production and consumption of cement, construction sand and gravel, crushed stone and gypsum, which are used almost exclusively in construction. Performances in other sectors were mixed and less easily characterized. Recovery from the economic decline of 2008-2009 became apparent in 2010, as prices for many mineral commodities continued to rise with increasing demand for those materials or the products in which they are found.

Jan 1, 2011

By Emily Sarver, August Greth, Cigdem Keles, Setareh Ghaychi Afrouz

The characterization of respirable dust on the basis of constituent fractions and particle sizes is increasingly of concern for evaluating exposure hazards. For high-resolution particle analysis, scanning electron microscopy with energy dispersive X-ray (SEM-EDX) can be an effective tool. However, it requires particles to be deposited on a smooth, uniform substrate such as a polycarbonate (PC) filter for optimal results. While direct sampling onto PC is possible, this is not the standard approach in many situations. For example, in coal mines, respirable dust samples have typically been collected onto polyvinyl chloride (PVC) filters because they are intended for gravimetric and/or infrared spectroscopy analysis. Such fibrous substrates are not ideal for SEM-EDX (or other microscopy), but an effective method to recover and redeposit the dust particles could render such samples suitable for the additional analysis. Here, we present a simple method and compare SEM-EDX results for paired samples analyzed directly on PC and following recovery from PVC and redeposition on PC. Both laboratorygenerated dust samples (n = 10 pairs) and field samples of respirable coal mine dust (n = 44 pairs) are included in this study. Although some changes in particle size distributions were observed between samples analyzed directly and those that were recovered and redeposited prior to analysis, the results indicate the dust recovery method generally yields a representative sample in terms of mineral constituents. That said, results also highlighted the effects of high particle loading density on individual particle analysis. Considering all sample pairs, those with similar loading density between the directly analyzed and recovered sample tended to exhibit similar mineralogy distributions. This was generally the case for the lab-generated sample pairs, and the Freeman-Halton exact test of independence indicated that the samples in just three (of 10) pairs were in disagreement in terms of their mineralogy distributions. On the other hand, for the field samples, the directly analyzed sample often had higher loading density than the recovered sample; and the Freeman-Halton test showed that 25 (of 44) pairs were in disagreement. However, the effect of possible particle agglomeration on the directly analyzed samples cannot be ruled out—and exploration of this factor was beyond the scope of the current study.

May 17, 2024

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011

By H Sichani-Teimouri, B N. Noller, J C. Ng, R N. Alsaadi, P L. Breuer, S Shini

Cyanide has been used for over a century worldwide for gold extraction. However, the presence of several metals and metalloids in ore requires greater amount of cyanide for an efficient gold recovery due to their solubilisation in conjunction with gold. The extraction residues are discharged into tailing storage facilities (TSFs) and may cause bird mortality if there is exposure to cyanide-bearing wastewater exceeding the toxic threshold. The toxicity arises from free cyanide released from weak acid dissociable (WAD) cyanide complexes. The International Cyanide Management Code (ICMC) has deemed 50 mg/L of WAD cyanide released into TSFs to be safe for wildlife protection. However, this concentration is based on observations of an apparent lack of toxicity rather than a toxicological approach. The National Industrial Chemicals Notification and Assessment Scheme (NICNAS) identified in 2010 that there is a lack of toxicity data to properly assess the environmental significance of cyanide levels at gold mines. Lack of knowledge for the toxicity of free cyanide and metal cyanide complexes to wildlife led to consider alternative direct assessment techniques for designating safe levels. Whilst toxicity may be assessed by using young chickens with animal ethics approval, the traditional bioassay approach to assess cyanide toxicity is impractical for gold mine TSFs. Bioassays using algal species such as Euglena gracilis, a unicellular alga, are widely used for ecotoxicological studies. A unique feature is that the Euglena gracilis Z cell has plant-like while SMZ cell has animal-like characteristics. The aims of this project are to evaluate the suitability of Euglena gracilis Z and SMZ strains to assess the toxicity of free cyanide and both strong (cobalt) and weak (zinc, copper and nickel) acid dissociable metal-cyanide complexes that may be present in TSFs.CITATION:Noller, B N, Ng, J C, Shini, S, Breuer, P L, Sichani-Teimouri, H and Alsaadi, R N, 2014. Development of a toxicity approach to evaluate free cyanide and metal cyanide complexes in waters associated with gold and other mining, in Proceedings Life-of-Mine 2014 , pp 573–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By L Scheunis, A Van den Bulck, E Jak, K Verbeken, M Shevchenko, R Starykh, I Bellemans, P-J Boeykens

As a result of the globally increasing consumer use of electronic devices, it is expected that pressure will increase on the supply chain of precious metals. Hence, recycling of these electronics becomes increasingly important, as well as optimising the current processes. One major issue in metallurgical processes is the amount of metal that is lost into the slag. This metal loss is inherent to the production process and therefore, additional processing steps such as slag cleaning may be required. Slag cleaning can be done in electrical resistance furnaces where heat is produced using the Joule effect, making the slag’s electrical conductivity an important operating parameter. Since slags are ionic liquids, the electrical conduction happens via the movement of ions which is called ionic conductivity. However, within the presence of transition metal oxides, a second mechanism of conductivity occurs as electrons are able to hop from one transition state to another, which is known as electronic conductivity. As ‘FeO’ is a common slag component in the non-ferrous pyrometallurgical industry, both mechanisms are present, but their proportions vary with the respective amounts of the two forms of the multi-valent ions and hence, with the oxygen partial pressure. The goal of the present study is to develop an experimental set-up and methodology for measuring the electrical conductivity of synthetic SiO2 – CaO – AlO1.5 – ‘FeO’ slags at various oxygen partial pressures.

Jun 19, 2024

By Theodore R. Jolley

The estimated recoverable reserves in the area in the vicinity of Eska 2 mine are, 699,300 tons in the Chapin and Emery bas of the Maitland group. Those recoverable reserves are in the area between the Eska fault zone and Jonesville fault and extend down dip from the outcrops. No reserves were developed by the Eska 2 entry or by drill hole 14-16 in the Eska fault zone. The small quantity of reserves in the vicinity of the Eska 2 mine is insufficient to justify development of a now, modern .nine in this area. The estimated recoverable reserves in the area east of aka Creek are 974,500 tons in the Eska, Shaw, and Martin beds of the Eska group. Most of those reserves occur in the south limb of the syncline. It will be necessary to practice subjacent mining methods to recover these reserves in the Eska group. The Eska bed developed by the diamond drilling in this area comprises coal end few thin partings. The Shaw and Martin beds comprise two bunches of coal separated by partings, and the product from full-bed mining will require thorough preparation.

Jan 1, 1952

It is a pleasure to submit to the National Critical Materials Council (Council) some of my thoughts concerning the important tasks which lie before you. It long has been my belief that America's economic health and national security may depend to a substantial degree on whether we have available to us an adequate supply of critical and strategic materials at reasonable cost. To the extent the Council can contribute to the identification and implementation of wise public policies which facilitate the achievement of that goal, we and our children should be grateful. Even before assuming office, President Reagan warned of the danger of undue dependence on imported materials essential to the Nation's defense and economic well-being. After his election, he appointed a transition task force on strategic and critical materials, and he later directed the Cabinet Council on Natural Resources and Environment to prepare .a National Materials and Minerals Program Plan and Report to Congress, which he forwarded to the Congress in April 1982. In 1984, my predecessor, Secretary Clark, established the National Strategic Materials and Minerals Program Advisory Committee, popularly known as the "Mott Committee" because of its distinguished chairman, retired Admiral William C. Mott.

Jan 1, 1986

By Phillip I. Merritt

"IntroductionDuring and since• the war, it has been my privilege to work closely with those in Canada who are responsible for the vital raw materials needed in our co-operative atomic energy programme. The understanding which has developed between our two groups in this all-important enterprise has been a great source of pleasure. We in the United States are aware of the importance of the contribution made by Canada to this project, and we look forward to continuing our mutually advantageous relationship.The impact of World War II, and the decision by Canada, Great Britain, and the United States to join in a programme for the development of atomic weapons, created a sudden and immense demand for uranium minerals. Early in the raw materials programme, it was evident that sufficient raw materials to fulfill war-time atomic weapon requirements could be secured from three sources: the rich pitchblende deposits of the Eldorado , mine at Great Bear lake; the Shinkolobwe mine in the Belgian Congo; and as a by-product of the vanadium industry of the Colorado Plateau in the United States. In the early part of the programme, therefore, our joint efforts were directed toward obtaining immediate maximum production from these localities. The contribution made by Eldorado Mining and Refining (1944), Limited, both in supplying and refining raw materials, was and continues to be of vital importance.In addition, it was also obvious from the first that in this programme, as in any mining enterprise, exploration activities directed•toward the discovery and development of new sources of uranium ore were essential if production were to be maintained over an extended period of time. In order to satisfy obvious security requirements during the war, it was necessary to proceed with this exploration programme, both in Canada and the United States, as secretly as possible. With the end of the war, and the revelation that an atomic weapon had been developed, however, secrecy in exploration was no longer required. The important thing was to get on with a broadened exploration programme."

Jan 1, 1950

By Willie van Niekerk

As mining projects get larger and more complex there is a need to examine the use of project management techniques developed for large construction projects in order to ensure completion of the project on time and budget. In recent years the construction/civil industry has sought new methods to ensure that multimillion dollar projects involving multiple contractors, working in an increasingly legislated work environment, are delivered to the clients satisfaction. The paper describes these methods, which range from program management to systems and tools to gather all project information such as schedule and cost, and relates how these can be applied to large international mining projects. The paper also describes the benefits that an independent project manager can bring to a client or owner?s team by setting up the relevant organization and controls together with the appropriate contract and procurement strategy.

May 1, 2009

"The management of outlier grades in positively skewed gold distributions is a contentious issue. Incorporating outliers in standard ordinary kriging (OK) estimation procedures in a way that honours the data without smearing extreme grades into surrounding areas has been problematic. Cutting or capping of outliers to mitigate their influence in estimation techniques is common practice, while methods that manipulate the OK system of equations fail to honour the data. We propose a method of post-processing of kriging weights that provides realistic OK estimates and mitigates smearing without manipulating kriging equations or changing the original grades. The method requires that the data is not clustered, is approximately equally spaced, and is of the same support. Positively skewed data is ordered on attribute grade and nonlinearly transformed to a Gaussian histogram of categorical bins whose frequency is based on their likelihood of occurrence and location in the sample distributions. Factors that restrict kriging weights are calculated by dividing the percentage frequency of data in each bin by the percentage frequency of data in the bin with the highest frequency. Restriction factors applied to the kriging weights in the OK estimation restrict the range of influence in proportion to their probability of occurrence in the distribution. Smear reduction post-processing is easy to implement and addresses issues arising from negative kriging weights while considering the spatial location of samples, the sample grades, and their probability of occurrence. The method mitigates both smoothing and conditional bias.IntroductionOutliers are sample observations that deviate considerably from the standard or expected (Hawkins, 1980). These deviations can be high or low in grade depending on the distribution. The presence of outliers in a mine sampling campaign could provoke mixed reactions. Mining engineers might view high-grade outliers as a promise of achieving higher grades, while the geostatisticians view outliers as affecting the accuracy and precision of the overall estimate, among other issues. Having identified outliers, the geostatistician must decide how to account for their presence and treat them so that true underlying estimates are not distorted. Advanced knowledge of the deposit allows the geostatistician to identify and treat outliers acceptably, especially where samples are limited in number and the true grade distribution is uncertain. If ignored, or treated incorrectly, outliers are likely to lead to smearing of extreme grades into the surrounding estimates, thereby steering regions towards potential under- or over-estimation."

Apr 1, 2019

By Robert S. Young

During the last quarter-century, exploration for metallic deposits in Maine has been sporadic with peaks generally coinciding with periods of high metal prices. Known cases of regional or semi-regional evaluations are few; most efforts have been local and usually intensive. On the basis of broad geologic groups, the State has been divided into five fundamental environments: ( 1) coastal metamorphic belt; (2) southern volcanic belt; (3) Silurian slate belt; ( 4) northern volcanic belt; and ( 5) Devonian slate belt. Although not restricted to these areas, exploration in recent years has been concentrated in the northern and southern volcanic belts. Notable examples of recent exploration activity, directed to sulfide minerals, include: ( 1) the Knox County nickel-copper-bearing ultramafic rocks; (2) the Harborside (Cape Rosier) copper-zinc deposit; (3) the Second Pond (Black Hawk) zinc-copper-lead-silver deposit; ( 4) the Big Hill-Barrett lead-zincsilver- copper-gold zones; (5) the Parmachenee copper-zinc belt; ( 6) the Moxie Lake nickeliferous peridotite; and (7) the Attean quartzmonzonite molybdenum-copper occurrences. The Second Pond and Harborside prospects appear to be close to production. Systematic investigations for non-metallic deposits appear to have been aimed principally toward limestone, asbestos, diatomaceous earth, and spodumene-bearing pegmatites. Advances in prospecting methods, high metal prices, a favorable business outlook, increasing cooperation from large landholders, and some discoveries support the probability of increased exploration activity in Maine during the coming decade.

Jan 1, 1968

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973

By Hugo de León Carvalho Cedro

O presente trabalho tem como objetivo avaliar os efeitos da degradação da superfície de lentes de contato via métodos ópticos. Sendo biomateriais, as lentes estão em contato direto com estruturas sensíveis do corpo humano e seu uso surge da necessidade de reduzir enfermidades, propiciando melhora da acuidade visual e proteção ocular. Outro aspecto relevante é que as lentes se tornam uma nova estrutura refrativa de entrada da luz no globo ocular, e desse modo devem manter características de transmitância compatíveis com a córnea. Com o uso das lentes, é esperado uma degradação natural das propriedades ópticas e superficiais da mesma. Para avaliarmos essa degradação, foi planejado um experimento com um ensaio de degradação. O ensaio de degradação visa comparar o efeito de diferentes soluções simuladoras sobre a superfície das lentes tóricas: solução extrema de acetato de potássio 5% pH5, solução fisiológica usada pelo fabricante do tipo Boston Simplus multiação e solução de água ultrapura obtida de um dispositivo milli-Q (controle). O efeito da degradação foi analisado através do estudo das variações da topografia e da transmitância da lente.

Oct 30, 2017