Search Documents

By Randy Wheeler

The importance of having full wave form information for recorded blast events cannot be overstated. Knowing the peak particle velocity and the frequency at the peak are the tip of the iceberg. This presentation will focus primarily on using the FFT (fast Fourier transform) for detailed frequency analysis. Employing linear superposition to evaluate timing effects on amplitude and frequency will be discussed.

Jan 1, 2005

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By Wenshan Zhang

Three important methods of removing Fe in hydrometallurgy of zinc, manganese, copper, nickel, cobalt and etc are described, including neutralized hydrolysis method, jarosite method and goethite method. The reactions, technical requirements and thermodynamic analysis during Fe removal process are also discussed in this paper.

Jan 1, 2006

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By S. H. Lau

Rapid 3D characterization of multiphase mineral particles in a variety of mineral processing applications is described, including: mineral liberation analysis, grain size, mineral exposure analysis, particle damage, and pore network structure for fluid flow simulation in heap leaching. While micro X-ray computed tomography systems (microCTs) have been used for many years, industrial adoption is limited due to a variety of reasons, including insufficient resolution, the general lack of imaging contrast to differentiate different mineral phases within a multiphase mineral particle and the lack of automated 3D mineral processing software. For example, resolution with industrial CTs and desktop microCT is of the order of tens of microns to a few microns at best, depending on specimen size and CT configuration. We describe a novel lab-based X-ray microscope, XRM, which overcomes these resolution and contrast limitations, notably as the industry is going towards finer grains and more complex ore bodies. Using lens-based optics and detectors (similar to its XRM counterpart in synchrotron beam lines), resolution of the lab based system is in the submicron range with contrast better than conventional microCTs. Hence, visualization, differentiation and segmentation of most mineral phases of interest to the industry are now feasible. Coupling these high resolution and high contrast tomography images with a suite of customized 3D segmentation algorithms and analysis software, applications in mineral liberation analysis for process control, particle damage assessment and other mineral processing applications can be achieved. This non invasive 3D technique which requires relatively little sample preparation is currently being considered for coal, industrial minerals, and base/precious metal ores, complementing existing microscopy techniques such as QEMSCAN and MLA for a variety of applications

Sep 1, 2012

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

By J. Gómez-Hernández, P. K. Kaiser

Abstract The process of stress-induced fracturing around underground excavations in brittle rock is associated with dilation or volume increase of the failed, fractured rock. Different attempts to account analytically for this dilation have been made within the framework of plasticity theory. This theory has been developed mostly for metals, strain-hardening materials or soils, but brittle failure of rock-like materials is characterized by strain-softening behaviour and the volume change is dominated by geometric factors, which may violate stability principles of plasticity. In this work a semi-empirical Rock Mass Bulking Model (RMBM) was developed, using as starting concepts: dilation angle, plastic strain rates, effective deformation modulus, effective Poisson's ratio, Griffith locus, and the definition of a bulking factor BF introduced by Kaiser et al. (1996). The model was calibrated in order to obtain bulking factors that are consistent with experimental data and case studies of measured bulking around underground excavations. Résumé La fracturation provoquée par le stress autour des excavations souterraines dans le minéral friable est associée à la dilatation ou à l’augmentation du volume de la roche en rupture. Dans le cadre de la théorie de la plasticité, différents essais ont été faits dans le but de trouver une justification analytique pour cette dilatation. Cette théorie a d’abord été élaborée pour les métaux, les matériaux ou les sols d’écrouissage, mais la rupture fragile de matériaux d’aspect rocheux est caractérisée par un comportement d’amollissement et le changement de volume est dominé par des facteurs géométriques, ce qui pourrait ne pas être conforme aux principes de stabilité de la plasticité. Dans le présent ouvrage, un Modèle semi-empirique de masse rocheuse a été élaboré, dont les concepts initiaux sont les suivants : angle de dilatation, vitesse de fluage plastique, module effectif de déformation, coefficient effectif de Poisson, locus de Griffith, et la définition d’un facteur de foisonnement FF apportée par Kaiser et al. (1996). Le modèle a été calibré afin d’obtenir des facteurs de foisonnement qui soient conformes aux données expérimentales et aux études de cas sur le foisonnement mesuré autour des excavations souterraines. Kurzfassung Der Prozess von Brüchen in unterirdischen Abgrabungen in sprödem Gestein ist mit der Ausweitung oder der Volumenzunahme des gebrochenen Gesteins verbunden. Verschiedene Versuche im Rahmen der Verformbarkeitstheorie haben versucht, diese Ausweitung analytisch festzustellen. Die Verformbarkeitstheorie wurde hauptsächlich für Metalle, kalthärtende Werkstoffe oder Böden entwickelt, da sprödes Versagen von Gestein ähnlichen Werkstoffen von kaltenhärtendem Materialverhalten gekennzeichtnet ist, und die Volumenveränderung von geometrischen Faktoren beherrscht wird, die die Stabilitätsprinzipien der Plastizität übertreten. In dieser Arbeit wurde ein halbempirisches Rock Mass Bulking Model (RMBM) (Modell für das Aufgehen der Gesteinsmasse), entwickelt, für das die folgenden Anfangsprinzipien benutzt wurden: Ausweitungswinkel, plastische Fliessensätze, wirksames Verformungsmodul, leistungsfähiges Poissons Verhältnis, die Griffith Ortskurve und die Bestimmung eines Aufgehensfaktor BF1 der von Kaiser et al. (1996) eingefürt wurde. Das Modell wurde so kalibriert, dass es die Aufgehenfaktoren erzielte, die mit den Vesuchsangaben und den Fallstudien von Aufgehensmessungen in unterirdischen Abgrabungen übereinstimmen.

Jan 1, 2003

The Effect of Molecular Weight on the Adsorption and Efficacy of Polysaccharide Depressants

Sep 13, 2010

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

By Attie J. Goosen, William L. Spiteri

Although the physical characteristics of ANFO made from porous prilled ammonium nitrate (PPAN) have been altered by the addition of crystal modifiers, the optimisation of prilling processes and the admixture of waterproofing agents, the sensitivity of this explosive has not been modified on a commercial scale in the 40 years since its accidental discovery.

Jan 1, 1995

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

By Michael J. Bertoldi

The purpose of this Bureau of Mines report is to describe the methods and establish the basic economics for dragline, shovel-truck, and scraper mining systems. An overall view of the techniques of preliminary design and the cost involved is presented. Considerations of equipment selection, emphasizing short-range evaluation of required equipment, and a long-range evaluation are considered at a constant production rate over the life of a hypothetical mine. Separate cost analyses for each system were based on 1977 equipment prices, prevailing wage rates, and associated mining costs. Specific engineering and cost breakdown for such items as access roads, transmission line installation, rail spurs, etc., are beyond the scope of this report.

Jan 1, 1977

By C. A. Brown

"Steady-state simulation has been used for over 20 years to optimise the operation of crushing and grinding circuits. Throughout that period continuing comminution research has been the basis for improving the models.Site surveys, ore characterisation, model development and investigation of different operating scenarios by simulation has proved to be a cost-effective method for improving plant performance. In this sense, this paper presents findings from experience with these valuable optimisation techniques with reference to specific case studies."

Sep 12, 2005

By A. Matzick

In its work under the Synthetic Liquid Fuels Program the Bureau of Mines has developed on a 6-ton-a-day-pilot-plant scale a continuous, gravity-feed retort far distilling oil from oil shale. The development work covered by this report was done from January 27, 1950, to January 26, 1952, at the ail-Shale Experiment Station near Rifle, Colo. Over 300 pilot-plant tests were made during the investigation. The basic retort developed has been named the Gas-Combustion retort. In this process, part of the heat for retorting of the shale is generated by burning recycled product gas in a combustion zone within the descending shale bad in the retort. Additional heat is supplied by combustion of the carbonaceous residue remaining in the spent shale after the oil has been distilled. Air for combustion is admitted through an air distributor in the center of the bed at about the mid-point of the retort. Hot gas rising from the combustion zone heats countercurrently the descending raw shale and liberated shale oil by pyrolysis of the shale. After passing through and exchanging heat with the incoming raw shale, the oil is condensed as a fog or mist in the gas, which is withdrawn at the tip of the retort. The cool gas is then piped to an oil-recovery system where the oil is separated from the gas in centrifugal separators or other types of mechanical or electrostatic separators. The hot, spent shale below the combustion zone is cooled by heat exchange with recycle gas, which is a portion of the effluent gas from the oil-recovery system.

Jan 1, 1955

By J. K. Whyatt

The paper presents an approach to design a multi level room and pillar layout in a 40m thick seam overlain by a major aquifer. The design was required to maximise extraction with due consideration of the general stability of the workings, the potential water hazards, and spontaneous combustion risks due to air leakage between horizons. The approach utilised was a combination of empirical pillar sizing for water hazard control with numerical modelling to assess potential interactions between horizons. The numerical modelling allowed the size of interleaves, and the appropriate staggers to be optimised in terms of stress distribution. The stress distribution allows both the general stability of the openings and more importantly the permeability changes around the openings to be determined. The permeability of coal is sensitive to stress, and an empirical stress to permeability relationship, and theoretical permeability to flow leakage relationship has been applied to interpreting the relative spontaneous combustion risk associated with each of the proposed layouts. The final proposed design is a compromise between maximum exploitation of reserves and consideration of water hazards and of spontaneous combustion risk. Further more detailed design will be required as more comprehensive data on the geotechnical properties of the coal and overburden become available.

Jan 1, 1996

By A. Karami

It is well established that an ordered sequencing of charge initiations in a blast pattern is an important design consideration that affects blasting performance. Delay times must be chosen such that damage to the rock mass is controlled. The accuracy of delay detonators is also of major concern. A large scatter could lead to an incorrect blast sequencing that would lead to damage to the rock mass causing increased over-break, degraded fragmentation, increased fly-rock and poor vibration control. In this study, the effect of using accurate delay detonators on the explosive energy generated is investigated. For this purpose, power spectral density of the blast vibration for delayed shots are calculated and compared with the case where holes are shot at the same time (no delay). At the end the results are presented and discussed.

Jan 1, 2000