Search Documents

By K. A. Grace

"An ore is a rock regardless of its rarity or value."* The application of geology does not cease with the discovery and delineation of a mineral resource, but continues in the calculation of the economic parameters that determine reserves. Reserve determination, reduced to essentials, is the determination of the cost of production of a mineral commodity from a resource. This cost comprises mining, processing, waste disposal, reclamation and marketing costs. Geological input is vital in the calculation of the individual cost parameters from mining to reclamation, and even has some impact on marketing. Geology thus has a critical role in the determination of reserves.

Jan 1, 1985

By B Mohanty, G Ludwig

A thorough assessment of development drilling and blasting practice was carried out at two underground mines at INCO operations in Thompson, Manitoba. The study showed that significant improvement in productivity can be achieved through careful selection of explosives and loading practice, and modifications of the standard blast lay-out. The analysis involved assessment of the effectiveness of various perimeter blasting methods, employing selected explosives and loading practice in both jumbo and jack-leg rounds. The blasting pattern as well as burden and spacing were varied to determine their effect on the blast results. The various types of explosives used were, pneumatically loaded ANFO, with and without detonating cord tracing, extra-strength detonating cord, and slurry and emulsion explosives with and without cord tracing. The study also dealt with various means to achieve increased rate of advance in both jumbo and jack-leg rounds. The diagnostic measurements consisted of VOD, 'burn' marks or half-barrels on perimeter wall, and blasting vibrations. The effects of geology, firing sequence, blast lay-out, and drill hole deviation on the final results were also examined. The results of the study have been shown to have very important bearing on the design of development round blasting.

Jan 1, 1998

By Linli Wu, Guangchun Yao

"The influence of deformation on the properties of short-carbon-fiber reinforced 2024 alloy matrix composites was investigated in this study. It was found that the distribution of carbon fibers changed from the random state before deformation to the ordered state that carbon fibers arranged along the direction of rolling and extruding after deformation. Under the temperature range in control, the increase of rolling and extruding temperature would benefit to improve strength and elongation of composites, but was not conductive to improve the hardness of composites. With the increment of total deformation, all the strength and the hardness of composites became greater, nevertheless the elongation decreased. After being rolled and extruded, the strength and the hardness of composites were all bigger than those of composites before being rolled and extruded; moreover, the strength of extruded 2024 alloy matrix composites was higher than that of rolled 2024 alloy matrix composites under the same heat treatment conditions.IntroductionCarbon fibers have been reckoned as very important reinforcements due to the high specific strength, specific modulus, high thermal and electric conductivity, low expansion coefficient and good self-lubricant properties [1-4]. Light metal composites reinforced with carbon fibers, such as carbon fibers in an aluminum matrix, are widely used and studied. Some studies have concentrated on the interfacial characteristic of CF/Al composites in order to search for the way of improving the bonding between carbon fibers and the matrix alloy [5-8], and on the influence of the carbon fiber percent composition in the composites [9-11]. Some researchers began to take interest in the deforming characteristic and failure behavior of carbon fiber reinforced metal matrix composites [12-16]. However, the same with other metal materials, most of CF/AI composites were prepared by some single processes, such as powder metallurgy, extrusion casting and vacuum press infiltration, which caused that the composites products could not be manufactured directly. In order to cover the shortage of the mentioned above processes and get composites products with perfect mechanical properties and dimensional accuracy, the composites should be reworked by rolling, extruding or forging process. Compared with research about manufacturing process, the correlative investigation on the reworking of CF/Al composites was much less evidently, which restricted the application and the further development of CF/Al composites."

Jan 1, 2012

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By T Warren, A Dempster, N Barnett, J Oh, S Saydam

The influence of the insulating properties of lunar regolith was shown in the sub-surface temperature tests performed by the Apollo missions, with no significant temperature fluctuations occurring below 80 cm from the lunar surface even if surface temperatures fluctuated >200 K between lunar days and nights (Heiken et al, 1991). Key to the thermal insulation of the regolith is its low density near the surface having the greatest insulative effect with the lunar regolith becomes denser with depth. As the regolith becomes denser, the thermal conductivity of the regolith increases (Hayne et al, 2017). Thermal modelling software, Oxford 3D Thermal Model, which mapped the lunar surface temperatures effect on the thermal influence at the lunar south pole sub-surface over a lunar year found areas with brief illumination with surface temperatures >120 K could have sub-surface temperatures <112 K that can sustain long-term stable water ice at depths of <30 cm (Paige et al, 1992; King et al, 2020). Further to this, the observation of water molecules or other hydroxyls by the NASA/DLR Stratospheric Observatory for Infrared Astronomy (SOFIA) in non-permanently shadowed regions (PSRs) on the Moon, indicated that water could be present beyond PSRs (Honniball et al, 2021). Using the Oxford 3D Thermal Model in selected regions in the lunar south pole, can provide insights into the location and depth of cold traps that could sustain water ice.

Nov 29, 2022

By F. R. McDonald

The proton NMR spectra of 32 pyridines in two solvents, carbon tetrachloride and benzene-d6, are presented. The chemical-shift and differential-shift values are correlated with the substitutent position and with the solvent media. The ring protons and the protons on alkyl substituents are tabulated. The paramagnetic shift of the protons adjacent to the nitrogen is discussed, and a proposed structure for the pyridine-benzene complex that is consistent with the observed anomalous paramagnetic shift is presented. The utility of the data in the identification of pyridine compounds found in shale-oil naphtha is demonstrated.

Jan 1, 1971

By John Mahoney

We live in a world of change and the mining industry is enjoying some of the most rapid changes today that have been seen in a long time, We&apos;d like you to open your mind to a new concept in material handling. Figure # 1 Shows a new concept combining some of the proven application advantages of the power shovel with which we are all familiar, and applies the advantages of the dragline for the benefit of the user. First, the hydraulic excavator enjoys tooth forces of the shovel because the dipper is attached to the machine with a dipperstick and boom, and can often actually realize greater tooth forces than a shovel because of the prize action of the dipper in hard digging. Second, the hydraulic excavator enjoys the application advantage of the dragline because both the operator and the machine are up above, sitting on top where the operator oversees the excavation and the machine&apos;s operating work range is greatly increased.

Jan 1, 1973

By Rita Michael

"The Marmara Ironworks was not the earliest ironworks in Ontario, but it was distinguished from other early works in a number of ways. It was established on an ambitious scale as a self-sufficient and, for the time, sophisticated community. In effect it was an iron plantation on the scale and scope of those at Hopewell, Pennsylvania and Saugus, Massachusetts(1). It was, besides, the only one of the few early ironworks in Upper Canada which operated almost to the end of the nineteenth century, albeit in fits and starts, and which used magnetic ores rather than bog iron ores (limonite). Furthermore it is the only works which has produced archaeological interest over a number of years. The ironworks is on the east bank of the Crowe River near Highway 7, on Lots 7 and 8, Concession 4, Marmara Township, Hastings County, Ontario. It is the property of the Village of Marmara, and the extant remains encompass about 2. 5 acres of the original 2000 or so which made up the original grant. The mineral riches of the Canadian Shield had been known since the days of the Jesuit missionary-explorers. A consortium headed by Alexander Henry and the Duke of Gloucester planned to exploit the copper near Sault Ste. Marie during the last part of the eighteenth century, but nothing came of the venture(2). This attempt may have grown out of Lord Dorchester&apos;s suggestion that private enterprise be encouraged in order that the iron ore which ""abounds"" in Canada might be exploited(3). John Graves Simcoe, the first Lieutenant Governor of Upper Canada was also anxious to see iron working develop. Simcoe was eager to encourage many enterprises, among which ""the development of iron mines""(4) - Governor Gore had been approached by John Mason for help with his ironworks in Norfolk County (5). Three Americans had applied for permission and support to erect an ironworks on the Gananoque River at the falls to become known as Furnace Falls. They were granted 1000 acres of land in fee simple to encourage their endeavor(6). Sir Peregrine Maitland, only a few months after taking up his duties as Lieutenant Governor in 1818, intended to visit the ""bed of iron ore on the Crow River"" (7) - Maitland was to provide a good deal of support, both moral and substantive, to Charles Hayes when he came to Canada in 1820."

Jan 1, 1999

On Nov 1, 2007 House Resolution 2262 ? The Hardrock Mining and Reclamation Act of 2007 ? was passed by the U.S. House by a vote of 244-166. HR-2262, among other things, would impose a 4-per-cent royalty on existing mines with commercial production and an 8-percent gross royalty on all new claims. Not surprisingly, this possible new law was one of the hottest topics of discussion at the Northwest Mining Association?s conference that this year returned to Spokane, WA for its 113th annual meeting on Dec. 3-7. More than 1,800 delegates attended the conference that was held under the banner theme of ?Mining ?. For today and tomorrow.? Northwest Mining Association executive director Laura Skaer was one of many speakers during the three-day conference to respond to the threat to the industry posed by HR-2262 with a presentation titled ?Potential changes to the 1872 Mining Law.? In the presentation that she first unveiled at the Alaska Miners Association?s convention and trade show on Nov. 8, Skaer laid out a comprehensive list of problems with HR-2262. In addition to the association?s obvious concerns about the proposed royalty, Skaer noted that the bill includes a mine veto provision that would allow the Secretary of the Interior the authority to deny an operations permit to a project if the secretary determines that the operation would cause undue degradation to public lands and resources. Potential massive withdrawals from mineral entry are also included in HR-2262. Among the lands that could be off limits to miners under HR-2262 are wilderness study areas, areas of environmental concern and 23.6 hm2 (58.5 million acres) identified as Roadless Rule. States, political subdivisions and Indian Tribes would also have more authority to withdraw lands, she said. To combat the proposed changes, Skaer made 10 trips to Washington D.C. on behalf of NWMA members in 2007. In her presentation at the annual meeting, she also objected to provisions that include no life-of-mine permits and uncertain permit renewals and new and duplicative environmental standards that she said are vague, ambiguous and inconsistent with current federal and state environmental laws. Debra W. Struhsacker, an environmental permitting and government relations consultant, also spoke on the issue of HR-2262 with a presentation titled ?The House mining law bill ? Rip van Winkle is back ? and he?s meaner than ever.?

Jan 1, 2008

By D Wallace, H Guo, B Shen

Appropriate management of the ground subsidence induced by coal mining activities is essential. To assess the effectiveness of grout injection for mining subsidence control, time-lapse ground penetrating radar (GPR) imaging data were collected before and after grouting. The pregouting subsurface responses were interpreted to have changed after grout injection. The changes were caused by injecting the grout materials (flyash and water) into the delaminated strata and permeable fracture zones. The largest distance of the observed GPR event changes at the right end of the main profile is 132 m away from the injection borehole. Although the GPR images could not easily tell if the image changes were caused by the injected ashes or the water, it does suggest that the injection materials had been pushed at least 130 m away from the injection borehole. This is consistent with the borehole scan monitoring, which confirmed that the grout has travelled more than 90 m from the injection borehole.

Jan 1, 2006

By M. A. Ouederni, G. C. Chorosz, E. P. Déliac

This paper deals with the heat flow problems in deep workings (depth greater than 1000 m in France). The approach benefitted from experience gathered in France and South Africa. Deep mines are located in the East of France (coal in Lorraine and potash in Alsace), where the geothermal gradient can reach 4 &apos;C per 100 m (Virgin Rock Temperatures, VRT, around 50 &apos;C). This paper is concerned with the following topics: method of studying the heat flow problem on a mine-wide basis, specific models for heat and moisture pick-up, interfacing of heat and ventilation calculations and a case history in the Lorraine collieries. The heat flow problem on a mine-wide basis is studied in a fashion similar to ventilation networks. Each branch is considered as a "black box" where the air picks up heat and moisture (or is cooled, in the case of an air-cooler). Each box is therefore modeled as a heat transfer unit, hence the calculation of outlet temperatures (wet- and dry-bulb) from the intake ones. The whole network can thus be computed as a sequence of boxes from the air intakes towards the outlets. The second section reviews a number of models used for the assessment of heat and moisture pick-up in the "boxes", with emphasis on stopes and development ends, which are particular to the mining method in use. Two types of stopes are considered: longwall (horizontal and inclined) and cut-and-fill (subvertical). Mechanized rock breaking and blasting can be accounted for. A particular attention is given to development ends, especially complex from the heat flow point of view (rock characteristics, wetness factors, etc.) and usually quite hot. These workings, which are critical in order to secure new production areas, are studied on an average basis as well as in extreme conditions. The calculation takes into account the history of rock temperatures. The interaction between ventilation and thermodynamic calculations is still under development. The idea consists of coupling ventilation calculations with the "box" models: the first step determines the direction of air flow, hence the sequence of the boxes; thereafter the calculations yield the effect of temperature and presssures on air flows. The final section reports on the validation of the whole approach against field data. It concerns several heat flow surveys aimed at checking the models for shafts, stopes and development ends. The accuracy of the method is found very satisfactory.

Jan 1, 1987

By C. L. Schaidle

Computers and communications technology have revolutionized many industries. In earthmoving, this revolution has just begun. The major changes are still to come, but they are just around the corner. This paper presents a vision of this up-coming revolution in our industry. This vision is comprehensive. It includes basic communication, machine monitoring and diagnostics, job and business management, planning and operations, and machine control. For our industry to realize maximum benefits from the information age, we must have a vision of the future that is shared by technologists, machinery producers, and miners.

Jan 1, 1994

By D Flint, O Rindriatmoko

PT FreeportÆs Deep Ore Zone (DOZ) Mine is the latest block cave mine within the East Ertsberg Skarn System (EESS).Issues with undercutting and stress concentrations at the extraction level were experienced, leading to reduced pillar strength.The extraction level-related issues became more pronounced, leading to local panel drift collapse, in an area that was over 100 per cent extraction. A review of ground conditions, panel collapse descriptions, and factors contributing to panel collapse are presented in this paper.

Jan 1, 2005

By I. D. Hagar

WHEN the history of American business during these momentous war years is written, an absorbing chapter will be devoted to the Maclntyre Development, in northern New York. It will tell of a timely mining project, deep in the wilds of the Adirondacks, blasted into being by Axis torpedoes. It will recount the labors of 1500 engineers and workmen, miles from a highway, rail line, or power source, who built a huge enterprise in a few short months&apos; time. And it will list these major contributions to the war effort: more than a quarter million tons per year of ilmenite, source of titanium dioxide-man&apos;s most opaque white pigment-to be used in paints for warships, tanks, guns, planes and the plants that build them; as a co-product, over 500,000 tons each year of magnetite-an important type of iron ore- to help feed the cavernous maw of America&apos;s wartime steel industry.

Jan 1, 1942

By R. P. Foster, ed.

The short selection of papers in the special issue provides an insight into the level of exploration activity in Africa and the science and technology that are underpinning it. A country-by-country survey is followed by discussion of geochemical exploration in tropical soils, the Liptako region of Niger, structural styles of deposits in Zimbabwe's Bulawayo-Bubi greenstone belt, structural controls in Zimbabwe's Eldorado shear zone, the regional framework for deposits in the Odzi-Mutare-Manica greenstone belt of Zimbabwe and Mozambique, and the Iperindo deposit in Nigeria's Ilesha schist belt

Apr 1, 1996

By Robert Hopler

HUDSON MAXIM A Noted Inventor of High Explosives ALTHOUGH the subject of the present sketch has been a tireless worker in many fields of activity, his name is best known in connection with his work in the development of high explosives and their application to modern ordnance

Jan 1, 2012

By A. L. Engel

The Bagdad-Chase copper-gold mine south of Ludlow, Calif., was visited by an engineer of the Bureau of Mines in July 1955 to determine the mine&apos;s status of activity and to obtain a bulk sample for metallurgical testing. The deposit was discovered in 1903 and has been worked intermittently. It has a production record of about 273,000 tons of ore. The first production of about 150,000 tons was treated in a cyanide plant 2 miles west of Barstow, Calif. The extraction of gold was not satisfactory because of the presence of copper minerals. Since 1910 the ore has been shipped to various smelters in Arizona and California for use as a flux.

Jan 1, 1957

By Otto Wartenweiler

After the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities, with some decomposed andesite, while the average value of mill feed was calculated to be $20 or more in gold, no silver being present. The tonnage to be treated at the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities for increasing the capacity to 400 tons. While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to receive the run-of-mine material, which was too coarse for a No. 5 crusher. TO accomplish the coarse grinding to best advantage, a careful comparison was made between the modern steel ball-mill—the last word in crushing and grinding—and one of its older, and, at that time better-established, competitors, the rolls. The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball-mills because a simpler arrangement is possible, and because the handling of ball-mills is preferred by the operator. A marked departure was introduced for fine grinding. Instead of the long type of tube-mill, using pebbles, a mill of similar design was selected, but of much shorter length, using small cast-steel balls as grinding medium. For cyanidation, the Dorr continuous countercurrent process was

Jan 1, 1918

By Marton A

The Readymix Group have a Quarry Improvement Program - &apos;Building in Quality (BIQ) which has many parallels to the ICI Explosives&apos; total quality management - &apos;Quality Improvement Program&apos; (QIP). Both companies have for some time recognised that the &apos;do it right first time&apos; principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By John Wellington Finch

WHAT is an engineering opportunity? To the mining .engineer the natural assumption is that the first requisite &apos;is a mineral deposit, but, of course, it is not so simple as that. There are at various points on the earth really very great mineral deposits which, on account of geographic location, backwardness of the country, or hostility of its natives, are now, and for a long time to come will be, quite valueless. The mining engineer, and for that matter the civil engineer, is more dependent upon the decisions of capital than upon any other factor in his profession. Ordinarily it is to be assumed that money will go to any place where it is clear that an adequate return upon its investment can be secured, but for many years it has not been safe to depend upon this. &apos; As already stated, there are many places where local conditions are such that mining is not safe to engage in and there are still other places in which conditions have been so aggravated by the Great War and by the social unrest which has upset the Asiatic region that capital is naturally most reluctant to venture, even when engineering data makes the undertaking appear attractive. It will be evident, I. believe, that there are many factors vital to the success of a mining enterprise in some of the remote countries which we do not have to consider in the United States and which do not, in fact, exist here.

Jan 1, 1924