Search Documents

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014

By W. F. Hahnert, P. A. S. Ralston

In off-line training of a rule-based controller, the significant measure of successful training is the quality of control provided by the generated rule set. In an adaptive or on-line control environment, performance is also measured by the ability to accurately maintain a satisfactory rule set, but within constraints on speed and/or resource availability. Very small population genetic algorithms, or microGAs, have been proposed as a means of capitalizing on the hill climbing characteristics of faster local optimization techniques while requiring less memory and retaining much of the robustness of traditional, larger population genetic search. A traditional genetic algorithm and a similar microGA are developed and applied to two control problems. The performance of these algorithms is analyzed with respect to (1) the quality of the rules learned, (2) the rate at which learning occurs, and (3) the memory resources required during learning.

Jan 1, 1993

By Alexander L. Peyton

The Magruder and Chambers copper deposits in the Little River gold district, on the border line of Lincoln and Wilkes Counties, Georgia, have been known for a number of years (fig. 1). The Magruder deposit was first opened as a gold mine but has produced mostly copper and load. Records show that about 50 cars of concentrates were shipped from this property. No record of any production at the Chambers deposit is available. The Bureau of Mines, in its program of investigation of strategic minerals deposits, diamond drilled 10 holes, totaling 3,784 feet, on the two properties between December 3, 1948, and June 23, 1949. Eighty-eight core samples were analyzed, and the analyses and drill-hole data are presented in this report.

Jan 1, 1950

By R. D. Schmidt

An in situ leaching geochemical simulator consisting of flow, mass transport, and graphics support programs has been developed. Two dimensional flow in heterogeneous porous media is modeled using a semi-analytic boundary integral technique. This method involves mapping streamlines to straight line segments in the complex potential plane. Leachant concentration and mineral values are modeled in this plane using the (one dimensional) potential coordinates. A fully implicit finite difference scheme is used to solve the resulting coupled system of four concentration equations. Graphical representations of streamline patterns, concentration histories, profiles and recovery curves are generated. An application of the model to uranium leaching in a heterogeneous aquifer and ore zone setting is presented.

Jan 1, 1985

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960

By Richard Scales, Giles Hellyer, Ian Travers, Dean French, Peter Bellairs

"The Mt Whaleback iron ore mine is located in the Hamersley Province situated about 1OOOkm to thenorth of Perth, the capital city of Western Australia. A small but significant portion of the waste in Mt Whaleback presents problems due to its ability to react with normal commercial bulk explosives resulting in premature detonations, two of which occurred at the mine in 1983 causing great consternation as well as disruption to the mining operation. The techniques and procedures developed to overcome this problem were based on the use of tough durable, acid and heat resistant liners to provide a physical barrier separating the explosive from the rock togetherwith the development of an accurate down the hole remote temperature logging technology. The liner technology was developed due to the inability to produce a reliable inhibited ANFO despite exhaustive mine based testwork."

Jan 1, 1999

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By Jürgen F. PH. D. Brune, Alex C. Smith, Michael A. Trevits

Underground coal mine fires in the United States continue to present a significant hazard to the safety and health of mine workers. The leading causes of mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion The National Institute for Occupational Safety and Health (NIOSH) is conducting an in-depth program of research to address mine fire prevention, early and reliable fire detection and mine fire suppression and control technologies. One segment of the research portfolio is focused on remote methods for addressing coal mine fires. This research is important because remote methods represent the primary means of fighting a mine fire when conditions are too dangerous to fight the fire directly underground. Technologies under investigation include remote methods for installing ventilation control devices (mine fire seals) and remote methods for suppressing the fire using, the injection of inert gas, gas-enhanced foam and jet engine exhaust gases into the fire zone. This paper presents a summary of remote mine firefighting technologies used in the U.S. and the results of completed NIOSH research.

By R. D. White

"The Cumberland Basin of Nova Scotia has long been considered a structural basin by virtue of the elliptical outcrop and inward dip pattern of the Pennsylvanian outcrops. Recent published and unpublished data indicate that subsidence began in the late Devonian, perhaps resulting from a graben or rift. The Mississippian sediments which filled the growing depression were continental, lacustrine and marine with evaporites. The cessation of the riftforming processes is recorded by the alluvial swamp-type sediments of the Pennsylvanian which filled the depression. In excess of 25,000 feet of Carboniferous rocks are believed to be present in the deepest part of the Basin. Starting with the rift hypothesis, we can speculate on the kinds of sediments, their location and the structural features present beneath the Pennsylvanian surface. Using surface exposures and a limited amount of subsurface data, we theorize that (1) the Mississippian evaporites acted as glide zones which effectively divided the Basin into two horizontal structural layers. The rocks above the evaporites, responding to Appalachian stresses, formed the long diapiric folds with cores of overthickened evaporites. Below the evaporites the structures are related to movements of the rift floor, compaction closures and structures formed by differential horizontal movements of the rift walls. (2) The rift, in its deeper parts, will have more and a greater variety of marine rocks than the outcrops indicate. Should the rift hypothesis be correct, the possibility of finding hydrocarbons is enhanced."

Jan 1, 1972

By C. O. Anderson, W. M. Meyers

Since 1922, when a brief report3 on the production and utilization of garnet was issued by the Bureau of Mines, there have been a number of interest—in developments in the technology of that mineral. Greater activity has been displayed in mining, new mills have been erected, and more attention has been paid to improvements in milling so that a more efficient and economical recovery of garnet has been possible. These activities have resulted in larger production; therefore, attempts are being made to broaden the market for garnet abrasives, and to find new uses for the unusual combination of physical properties than this mineral possesses. The writers have recently completed a field study of the occurrence, methods of mining and milling of garnet, and the manufacture and utilization of abrasive garnet products. This preliminary report indicates the most important sources of garnet, the methods by which it is recovered, and the manner in which it is recovered, and the manner in which it is utilized.Chemical and Physical Properties.The term ""garnet"" is applied to a closely related group of minerals which crystallize in the caste forms and possess similar physical properties, although their chemical composition may exhibit greater variation. The chemical composition of the garnet group may be represented by the general formula 3R"" O.R""' 203.3S102, in which R represents the bivalent elements calcium, magnesium, in the manganese state and ferrous iron, R"" represents the trivalent elements, ferric iron, aluminum and chromium in the chromie state. An account of the amorphous substitution of the different bivalent and trivalent elements, specimens whose composition may be represented by a definite formula are rare, the composition of any given specimen generally exhibits treat complexity.

Jun 1, 1925

By Turgay Gurun

"Digital simulation can be used as an analytical tool to optimize the design of crushing plants without need for large-scale experimental programs.General mathematical description of a crushing operation permits the simulation of a crushing plant flowsheet under various operating conditions. The process model encompasses multistage open- and closed-circuit crushing of hard and soft rock. Crushing balances are analyzed in the light of crusher and screen performance and a comparison of different closed-circuit arrangements is made in terms of process and layout criteria.The simulation model allows comparison of process alternatives to be made in terms of equipment selection and capital and operating cost estimation. It thus provides the pertinent practical information to maximize plant efficiency, and to minimize expenditures in such items as equipment, structures, power consumption, and so on."

Jan 1, 2014

By J. W. Davis

The storage stability characteristics of a diesel type fuel were determined to evaluate the effect of the polar compounds in the fuel. These compounds, comprising most of the nitrogen and oxygen containing compounds and many sulfur containing compounds, were separated from the fuel with a chromatographic column. This fraction was further separated into three polar extracts by graded elution through the column. Each extract was characterized. A storage program using the depolarized fuel, the fuel as received, and blends of the extracts with both fuels, was conducted. Results showed that the removal of the more polar components stabilized the fuel. Blending the polar extracts with the original fuel and with the depolarized fuel in the same ratio as they existed originally and at two and three times the original ratio increased the amount of gum present before storage, but had little effect on the formation of additional gum during storage. Distillate fuels produced by commercial refining of petroleum contain traces of organic nitrogen, sulfur, and oxygen compounds that are more polar4 than the remainder of the fuel. Recent laboratory studies by the Federal Bureau of Mines (1),6 in which these compounds were removed from a fuel, have shown that they influence its storage stability. The objective of this work was to determine the amount of these compounds present in a fuel and their effect upon its stability in storage. To evaluate the role of these polar compounds, it is necessary to remove them from the distillate fuel. Many can be removed by chemical treatment (2), but such treatment precludes reblending the polar components to approximate the original fuel composition. Solvent extraction is free of some of the criticism of chemical treatment, but it is more difficult because of the complex mixture from which compounds must be removed.

Jan 1, 1961

By B. M. Larsen

ATTEMPTING to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic " and " macroscopic," depending on whether the variations in concentration of solutes? or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also underly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all segregation effects. UNDERCOOLING AND NUCLEI FORMATION It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus tempera¬ture. In practical terms this means that the nuclei number increases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. TEMPERATURE GRADIENTS AND HEAT DISSIPATION DURING FREEZING Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period: Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1944

By V. Sheikhzadeh, M. Saghaeian, N. Esmaeili, R. Hejazi, A. Dehghani Ahmadabadi

High Pressure Grinding Rolls (HPGR) are mostly used prior to pelletising processes to increase the specific surface area (SSA) of iron ore concentrate. For expressing SSA, the Blaine index is utilised as one of the most important dimensional properties of iron ore pellet feed. ISO 21283 is a standard test method that explains the manual of Blaine air-permeability apparatus for determination of this parameter. In this standard, the disaggregation method is based on passing the minus of 1 mm samples from the 0.150 mm sieve. The disaggregation process has an effective role on the results of Blaine airpermeability test especially for regrinding HPGR products. In this research, firstly the Blaine index of samples was measured without disaggregation. Following this, disaggregation was done by passing the minus of 1 mm samples through three sieves with different dimensions, 0.150, 0.090 and 0.045 mm, separately, and the Blaine index was calculated for each one. Finally, lab-mill with rubber balls, called Jar mill, was investigated as another option. Screen analysis and image analysis with SEM were performed to evaluate the effects of the sample's disaggregation on the size distribution and agglomeration of samples. The results showed that the disaggregation method with sieve size 0.150 mm, according to ISO 21283, was not applicable for HPGR products because the particles were still stuck together. In addition, the disaggregation method with the sieve size 0.045 mm or with Jar mill offered reasonable results. Keywords: Disaggregation, Blaine index, specific surface area, regrinding HPGR, ISO 21283, Jar mill

Jan 1, 2020

By W. Evans, C. E. Ells

The agglomeration of hydrogen in pure aluminum and A1-Mg alloys has been studied through use of hydrogen introduced into the metal by cyclotron proton irradiation. Both the growth and dispersal of the agglomerates have been followed by metal-lographic techniques. During the cyclotron irradiation, agglomeration occurs at temperatures i 100°C for hydrogen concentrations as low as 1 ppm. On heating at elevated temperatures, 300°C to 600°C, intragranular agglomerates first coarsen and then disperse. The agglomerates formed at grain boundaries are much larger than the intragranular agglomerates; with hydrogen concentra- tions > 10 PPm, heating for 1 hr at 500°C results in extensive grain-boundary cracking. The hydrogen agglomerates have been shown to inhibit grain growth, but no inhibition of recrystallization has been observed. The ability of hydrogen to enter aluminum at a free surface, combined with its high-diffusion rate at elevated temperatures, accounts both for growth and dispersal of the agglomerates. Irradiations at elevated temperatures give results consistent with the explanation proposed for agglomerate behavior on post-irradiation heating. 1 HE formation of hydrogen-filled bubbles, or blisters. in aluminum and its alloys has been studied for over' thirty years. The work up to 1952 has been reviewed by Kostron' and since then Ransley and

Jan 1, 1963

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By Tatsuya Oki

Tantalum capacitors can be found mounted on printed circuit boards of domestic appliances such as personal computers. These capacitors contain a considerable quantity of expensive metal tantalum and can be detached and liberated from printed circuit boards by impact breakers. In this study, the size and density distribution of the liberated electronic devices were investigated. Then, tantalum capacitors were recovered from other electronic devices using size separation and pneumatic gravity concentration methods. More than 70% of Newton's separation efficiency was obtained for tantalum capacitors. High Newton's separation efficiency could be also obtained for other types of electronic devices such as chip resistors.

Jan 1, 2011