Search Documents

By W. R. VanSlyke

Scrubbing is gaining increasing recognition as a valuable tool in the treatment of Mesabi Range intermediate iron ores. In general, the earliest washing plants included log-washers in their various flowsheets. While log-washers certainly did impart a degree of scrubbing to the crude ore, such treatment bears little resemblance to the type of scrubbing being practiced today. At the time that these early plants were erected, only the true wash-ores were being processd. ("Wash-ores" are defined as crude ores in which relatively coarse chunks of almost completely liberated iron are found in a matrix of loosely-consolidated fine sand.) To treat ores of this type, sizing at approximately 65 to 100 mesh was sufficient to produce a merchantable concentrate. As crudes were being treated in which there was little "locking" of iron and silica, log-washers tended to disappear and large screens and classifiers took their place in Mesabi range flowsheets. The "screening and classification" type of flowsheet 'had its greatest usage in the 1945-55 period, generally speaking. During this same period, many operators found it necessary to supplement the "wash-ore" type flowsheet with heavy-media treatment.

Jan 1, 1959

By Jr. D'Angelo, Michael M. Blendy, Shawn Downey

"A grouted helical pile was used to support new buildings in the reconstruction of a large residential development. Foundation options were complicated by urban fill underlain with variable alluvial soil. A driven timber pile and grade beam system was recommended to support the new buildings. Other foundation options are also discussed. The grouted helical pile was quoted as an alternate and ultimately won the bid based on the economics and performance of the system. Data from 8 load tests was used to develop an empirical site specific relationship for determining pile capacity based on both installing torque and installation depth. Design to incorporate tolerance on installed pile location is presented. With the three phases completed, 554 residential dwelling units supported by 3645 grouted helical piles had been constructed covering 18 city blocks on the 44 acre site. IntroductionThe Philadelphia Housing Authority reconstructed the Tasker Homes housing complex located in southern Philadelphia, Pennsylvania, adjacent to the Schuylkill Expressway in the Grays Ferry area. Keating Building Corp. and Pennoni Associates were the general contractor and the structural engineer respectively. The original Tasker Homes development was constructed from 1940 to 1941 and consisted of 44 acres of primarily two and three-story residential brick buildings. These buildings were supported by a timber pile foundation system. The structural condition of the buildings supported on the timber piles was generally good in comparison to areas outside the buildings. These areas had settled possibly up to 2-feet in places due to the heterogeneous nature of the urban fill."

Jan 1, 2005

Engineering availability of the 120/200 tonne Wabco haulpak fleet at Mt. Whaleback was in the mid fifties and unstable. The project to achieve a reliable 66% during 1980 highlighted "plannable" maintenance, short cycle scheduling, condition monitoring, backlog control, and, above all, the importance of involving all affected people. It is not sufficient for consultants to design systems and make them work. The people who use the system must understand it, support it and "own" it. In this way, they will develop it and improve results after the outside help has been withdrawn INTRODUCTION In early 1979, PA proposed a programme to improve engineering availability of the Mt. Newman Mining fleet of 70 Wabco haulpak trucks of which 53 were 120 tonne and 17 were 200 tonne units. (Subsequently five 200 tonne trucks from Hamersley Iron were added to the fleet). The ore truck workshop was also responsible for 75 tonne trucks used as water trucks and general purpose vehicles. The need for action was clear. The fleet was achieving availability in the "mid fifties" with wide variations indicating that the fleet was becoming unreliable. Projected tonnages required a reliable 66% availability to be

Jan 1, 1982

By Allen M. Newcome

The Ohio valley division of consolidation coal company has incorporated two new aspects within its coal mining concern. A new communication system, thru the cooperation of the c. & p. Telephone company, has been established in each of our mines with its central control in the general office building. In conjunction with this system, a Texas instruments 960 a computer has been incorporated into the system. The purpose for our computer is to provide modernization and improvement to our safety, production and maintenance programs. Thru proper use, the computer will help eliminate inaccuracies and inefficiences that have previously caused inaccurate analysis of problems. Due to federal requirements for more reliable communications in underground mines, Ohio valley division is making a concentrated effort to improve its communication systems. Systems such as the magneto phone and trolley phone have been looked at more critically. It was found that these systems are being used well beyond their limits. With these facts in mind, division personnel started looking for a system that would have these built in advantages: ease of maintenance and installation, increased reliability, low cost, and an inherent ability as a multiple use system.

Jan 1, 1975

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Commun¬ications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By Collon C. Kennedy, Frances C. Hartogh, C. Joel Casburn

INTRODUCTION During the nineteenth century, the federal mining law was enacted with the objective of promoting the development of the western United States by providing unrestricted access to vast areas of federal land for mineral exploration. Prior to the advent of comprehensive federal, state and local land use plans, there was little, if any, regulation or restriction of mineral exploration activities. Today, the laissez-faire policies of the past that encouraged mineral exploration have gradually given way to the public's legitimate concerns regarding environmental protection, multiple use and planned land development. As a result, the contemporary prospector confronts a maze of statutes, ordinances and regulations with which he must comply to obtain the requisite approvals and permits before commencing mineral exploration on federal, state or private lands. This presentation will provide a broad overview of the exploration permitting process. The first section of this paper recommends certain general management practices to follow when attempting to obtain exploration permits. The second section presents two hypothetical cases, one involving a drilling program on private property in California and the other involving a drilling program and the removal of a bulk sample for metallurgical tests from federal land in Nevada. The cases are used to discuss jurisdictional issues and application of certain federal, state and county laws and regulations that pertain to mineral exploration. The final section contains a brief analysis of three important recent United States Supreme Court decisions. These decisions address the scope of the federal pre-emption doctrine as it applies to activities conducted on unpatented mining claims and the constitutional limits of permissible state and local land use and zoning regulations. PERMITTING PRACTICES The environmental impacts associated with mineral exploration generally result from the construction of drill sites, roads or trenches. Consequently, after the regulatory authority has considered the issues of permissible land use, the primary emphasis of the permitting process is to address problems related to pre-construction site identification and clearance, and post-construction site reclamation. The approaches taken to address these and other related issues vary with the scope of proposed work, the site, the appli-

Jan 1, 1987

By C. J. Hartley

"Scandium oxide can be recovered as a by-product from process streams in a number of chemical and metallurgical plants including TiO2 sulphate pigment, Ni/Co laterite, zirconium oxychloride and uranium operations. The feed materials available for processing can be either mid or end of process streams containing many species in solution. This paper describes the strategies available to limit coextraction of elements into scandium containing streams from TiO2 pigment production and the removal of these elements to deliver high purity scandium oxide.A critical part of process development is to work within the constraints of the main process in terms of introducing new unit processes and producing minimal additional process intermediates and residues. This requires flexibility in designing flowsheets and plants to find novel process routes that avoid production of intermediates and/or the introduction of reagents that can compromise the main process operations.Bloom Energy has developed novel solvent extraction processes for the extraction and refining of scandium oxide that minimise impacts on core process streams within TiO2 pigment plants. The additional unit processes are designed to have minimal contact with pigment plant process streams to produce a concentrate that is refined to nominal 3N purity scandium oxide in a simple, small scale commercial plant."

Jan 1, 2016

By Liu Wei-feng

Base on the thermodynamic calculation of vapor pressure of lead, antimony and arsenic at high temperature, the possibility of separating lead, antimony and arsenic in different temperature was analyzed ,and the practice of producing qualified antimony white from lead-antimony alloy by direct blowing was introduced in detail in this paper. The blast furnace reduction smelting was brief introduced firstly, and then alkaline refining was applied to removing arsenic from lead-antimony alloy that contains As1%,Sb39%,Pb58%,the arsenic in the treated lead-antimony alloy could decrease to 0.009% by that method. The antimony white containing Sb2O3 99.5% could be produced by air blowing in the special furnace at 650? from the treated lead-antimony alloy. And the electrolytic lead could be achieved by electrolysis from the lead-rich alloy which contained 83% lead.With high-grade product being obtained the process was shortened. The technology has been applied successfully many years in Guangxi, China.

Jan 1, 2009

By G. A. Kosick, C. A. Harris

"Metallurgy at the Polaris Mine is approaching an impasse, with lead and zinc concentrate grades and recoveries approaching their theoretical maximums. In an effort to increase productivity, plant throughput and operating material costs became a major focus of milling personnel.one method of increasing plant throughput was to minimize flotation circuit upsets by; standardizing operating strategy, decreasing control action response time of operators, increasing training of operators, and providing a more available decision support system for operators.To achieve these goals, Polaris personnel decided to utilize expert system technology to develop a real-time process controller for the flotation circuit which would be capable of justifying its actions to operating personnel.This paper describes the procedures followed in constructing the first process controller in the mineral industry which is based on the principles of Artificial Intelligence.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec and towed to its present location on Little Cornwallis Island, North West Territories, about 1450 kilometers from the North Pole. The plant presently treats about 2,800 MTPD of new feed with average feed grades of 3% Pb, 13% Zn and 5% Fe. Current production averages 36,000 tonnes of lead concentrate and 220,000 tonnes of zinc concentrate annually.In an effort to increase the efficiency of the concentrator, the decision was made to implement an innovative control system on the flotation circuit. This system would embody and utilize heuristics ""rules-of-thumb"" gained from operators to make on-line process decisions. It would also justify these decisions on a demand basis."

Jan 1, 1988

Opening AddressThank you for inviting me here today to open what promises to be a significant conference on the technological aspects of extractive metallurgy. I would especially like. to welcome delegates who have travelled great distances in order to contribute to, and be participants in, this examination of the technical innovations which have always been a crucial part of our industry.

Jan 1, 1992

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

By J. V. Happ

The investigation reported in this paper was prompted by the belief that vacuum processing of copper mattes could provide significant advancement to present-day copper smelting and converting technology. Specifically, vacuum distillation of copper mattes in a unit such as the R.H. vessel used in vacuum degassing of steel, can lead to improvements in: converter flue-gas-cleaning system, purity of acid (or liquid SO2), aisle hygiene, purity of electrorefined copper and smelter flexibility. In the study conducted, removal of Volatile impurities (arsenic, antimony, bismuth, lead and zinc) from liquid mattes, by vacuum distillation in a laboratory-scale equipment was performed. The conditions investigated covered a temperature range of 1123-1223K, absolute pressure of 6.5-0.5kPa (50 - 3 mm Hg) and with bleed gas consisting either of pure oxygen or argon. Six matte samples (four U.S. and two foreign) were tested. Under the "best" conditions arsenic and antimony were reduced to << 0.01% in the product matte. The removal of bismuth, lead and zinc was variable and appeared to be influenced by the matte composition of the sample. As might be expected, the rates of distillation of the various species were increased at higher temperatures and lower absolute pressures. The influence of a small flow rate of gas (02 or Ar) over the melt did not have a signifi¬cant influence on the extent of impurity removal. The magnetite content of the matte was reduced by up to 30% during vacuum treatment and was favored by a low partial pressure of oxygen over the melt. Substantial amounts of sulfur were also evaporated and an, overall increase in copper grade of the matte was realized. The paper concludes with an evaluation of industrial aspects of the process as applied to conventional smelters.

Jan 1, 1983

By M. Okido, H. Yamamoto, T. Sakamoto, R. Ichino, K. Kuroda

"Hydrogen absorption alloy films have been produced by molten salt electrolysis. Lanthanum-Nickel alloy film can be formed on a nickel substrate in KCl-NaCl-LaCb molten salts by electrolysis diffusion process. LaNi5 alloy was formed by mutual diffusion between La ·and Ni after La deposition on Ni substrate. Though several kinds of La-Ni compound existed in deposits, the alloy compounds on Ni substrate changed by electrolysis condition. According to the open-circuit potential measurement in molten salts after La electrodeposition, the formed compounds had a relation to the potential. In the case of the substrate electroplated a cobalt thin film on nickel, LaNi4_5Co0.5 was formed by the electrolysis in the molten salts with lanthanum ions. This ternary alloy film showed better hydrogen absorption behavior in cyclic charge/discharge test in alkaline solution.IntroductionHydrogen storage alloys have attracted attention as the active materials for batteries with the charge/discharge property at ambient temperature. The alloy of nickel and misch metal, mainly consisting of La and Ce, has been commercially 'used as a metal hydride with rechargeable property. In recent years, researches have been developed many kind of new alloys with better hydrogen absorption properties. The hydrogen absorbing alloy ingots are commonly produced by melting method of both metals in furnace, otherwise, prepared by mechanical grinding and metallurgical sintering technique with metal powders. The film is also made by vapor-phase techniques such as sputtering method, ion plating method, etc. ·We have proposed a new method to produce hydrogen absorbing alloy films by molten salts electrolysis technique [1-3]. The hydrogen absorbing film, LaNi5, Mg2Ni and CaNi5, were obtained in this process through controlling the electrolytic condition. The active metals, La, Mg and Ca, are electrodeposited on Ni substrate, diffuse into the substrate and form various kinds of intermetallic compounds. This technique provides a direct process using metal chlorides as resources to produce functional films without using active metals such as La, Ca and Mg."

Jan 1, 2000

By G. S. Scott, G. W. Jones

Trichloroethylene (CHC1CC12) is an important solvent for fats , resins , bitumens, rubber , sulfur , and phosphorus . It is used extensively in drycleaning because of its low order of combustibility and has recently been proposed as an inhalation anaesthetic . Its physical properties have been described by Carlisle and Levine . It is usually considered a noninflammable material ; however , substances that are noninflammable when mixed with air are not necessarily noninflammable when mixed with oxygen . Thus , Hewer's statement that " Trichloroethylene*** is not inflammable under any circumstances , nor will its vapor explode when mixed in any proportion with air , oxygen, or nitrous oxide , " requires qualification , especially in anesthesia, where pure oxygen may at times be substituted for air , This report gives the results of tests made to determine the inflammability of trichloroethylene in various mixtures of oxygen and nitrogen . The trichloroethylene used was Eastman's No. 1300. The boiling point was given as 86 ° to 87 °C . The specific gravity and refractive index of the sample measured in this laboratory were , respectively, 1.45 and 1.4759 at 25 °C .

Nov 1, 1942

By Fred Porter

Pollution problems from smelters may be unique in industry since the pollutants cover the wide range of SOx, particulates, carcinogens (arsenic), plus a number of heavy metals, the health implications of which are not clearly understood. In addition to this wide range of pollutants, many of the plants are extremely old; and fugitive emissions may, in fact, be the most significant air pollution problem. The Environmental Protection Agency, both in an in-house and contract effort, has assessed the quantity of pollutants emitted and evaluated the health impact. This paper will review the status of EPA&apos;s regulatory efforts in both new and existing smelters in light of these pollutant assessment studies.

Jan 1, 1976

By W. H. Mathews

"The Hardie group of cinnabar claims is in the interior of British Columbia; 25 miles northwest of the city of Kamloops. It is one of a number of mercury; properties scattered along a north trending belt 20 miles long and up to 5; miles wide. In all but one of these properties cinnabar is associated with; dolomite veinlets in zones of carbonate alteration in bedded rocks of Triassic; and Cretaceous (?) age; or in intrusives cutting these bedded rocks. No dolomite alteration or cinnabar mineralization is known in the undoubted Tertiary rocks adjacent to the mercury belt.The mercury showings of the Hardie group lie for the most part in a granitic stock cutting Cretaceous (?) volcanics. The rock in this intrusive shows marked variations in texture and has been described in earlier reports as granite and granodiorice, granite porphyry, and trachyte or dacite porphyry. At Hardie mountain the cinnabar mineralization, unlike that of the other properties, is associated with a fine-grained, almost chalcedoni c, quartz; carbonates, though present, are of minor importance. Some of the most interesting showings are found in an adit in the southeastern part of the property where cinnabar mineralization shows a very distinct structural but not a genetic relationship to a brown porphyry dyke 2 to 8 feet wide cutting a phase of the stock that may best be described as aplitic"

Jan 1, 1954

By J D. Goldsworthy

The McPhee Creek bedded iron deposit is a recent discovery made by Giralia Resources NL (Giralia) in the northern Pilbara of Western Australia. The deposit lies 30 km north of the town of Nullagine along the southeastern margin of the East Pilbara Granite-Greenstone Terrane (EPGGT).The McPhee Creek area is located in the Kelly Greenstone Belt in the southeastern part of the EPGGT. The Archaean aged greenstone belt consists of volcanic and sedimentary sequences including the Warrawoona Group and the Gorge Creek Group. The McPhee Creek iron ore deposit lies within banded iron formation (BIF) rocks of the Gorge Creek Group. The structure of the McPhee Creek area is dominated by a northeast trending, upright synform (Sandy Creek Syncline) and associated folding that is truncated by northeast trending faults in the east. Iron ore mineralisation is predominantly stratabound and follows the dip of the bedding – however, in some areas, particularly in the southwest of the deposit, mapped steep to moderate dips of bedding planes are at odds with underlying fl at mineralised zones in drill sections. Zones within the deposit that contain substantial thickness of iron ore correspond to areas of complex folding suggesting structural control and iron enrichment in fold hinges. Petrographic analyses confirm mineralisation is goethite dominant and the deposit is strongly supergene enriched.Giralia initially identified iron ore potential in the McPhee Creek area through the presence of a small known channel iron deposit (CID) mesa. Giralia began exploration in 2008 by re-drilling a portion of the CID (subsequently named Crescent Moon) and reported a small low-grade Inferred Mineral Resource. Target generation in the wider area utilising Geological Society of Western Australia maps and Ikonos satellite images identifi ed strongly ferruginous outcrops associated with major structures along an 8 km long range located 2.5 km to the west north-west of the Crescent Moon CID deposit. In late July 2008, a total of 62 rock chip samples were collected during a helicopter supported sampling program conducted at McPhee Creek. Samples taken from haematite-goethite enriched BIF and canga zones outcropping intermittently over the 8 km length of the western and central areas of the prominent range assayed up to 63 per cent Fe. These zones represent the discovery outcrops and surface expression of the McPhee Creek main range iron ore deposit.Follow up sampling, geological mapping, bulldozing of access tracks and ramps and reverse circulation (RC) drilling commenced in September 2009. A maiden Inferred Mineral Resource was announced by Giralia to the Australasian Securities Exchange (ASX) on 15 December 2009.The current Indicated and Inferred Mineral Resource at December 2010 stands at 260 Mt grading 56.2 per cent Fe, 0.12 per cent P, 6.7 per cent SiO2, 2.3 per cent Al2O3 and 9.5 per cent LOI at a 50 per cent Fe cut-off. McPhee Creek is one of the largest iron deposits found in Archaean BIF in the northern Pilbara.

Jul 11, 2011

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By B. Blaschuk

The Freeport McMoRan Bagdad Solvent Extraction (SX) circuit is the oldest plant of its kind currently in operation. The plant was commissioned in 1969 and was the second SX-EW operation to be built following the Ranchers Bluebird solvent extraction and electrowinning (SX-EW) plant near Miami, Arizona. Over the years of operation, the configuration of the SX has gone through many changes to accommodate a variety of pregnant leach solution (PLS) grades and flows. Although modifications to the original plant configuration are numerous, the Bagdad SX circuit has maintained its general form consisting of multiple long and narrow settlers. The unique configuration of the Bagdad SX circuit presents a variety of operational advantages and challenges; however, it continues to operate at a level recognized in the industry as excellent.

Jan 1, 2010

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973