Search Documents

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933

By H. A. Schwartz, W. Kenneth Bock

IN this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the position of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 400°C. (750°F.).

Jan 1, 1944

AS IS evident from the discussion in previous chapters, the methods by which an open-hearth heat may be made are numerous, but any heat, in the ingot form, may be classified as one of three types, depending upon the degree of deoxidation to which the metal is subjected. These are rimmed, semikilled, and killed, and desirable ingot structures, from the standpoint of distribution of porosity, are illustrated in Fig. 63. These are the most useful types of ingot structure [ ] and represent three stages in the continuous series from "wild" to "dead killed" (see Fig. 23, page 46) ; some of the variations of each type are discussed later in the chapter. The choice of ingot structure and of finishing practice used to produce the desired metal action in the molds is determined by consideration of: 1. Specified final analysis. As an example, the production of rimmed steels is mostly limited to carbon contents below 0.30 per cent and manganese contents below 0.60 per cent; on the other hand the production of low-carbon killed steel requires greater care.

Jan 1, 1944

By A. R. Przybylek

A fluid bed dryer has been designed for a nonconventional application to upgrade the value of fine anthracite culm and silt recovered from culm banks and anthracite tailings pond beds. This material can be seen as large spoil piles scattered throughout the anthracite coal regions of Eastern Pennsylvania. Engineering of the system commenced in December of 1986 and at this writing start-up is scheduled for late October or early November of 1987. This paper will focus on generalities concerned With system design and operation, and qualify the differences from conventional fluid bed coal drying systems.

Jan 1, 1988

By Carlos Del Río S

Se presume que el valor de los concentrados en tungsteno es afectado por un alto contenido de impurezas, generando considerables multas en el mercado minero. Por ello, el presente estudio señala la eliminación de estos sedimentos, a través de tres sistemas como el "leaching", la flotación y la separación magnética, donde además de obtenerse limpio el producto a costo de operación pequeña, se valoralizan los concentrados, evitando el pago de multas. Al tiempo que muestra la flotación de los sulfuros metálicos como el sistema más adecuado para separarlos de la hubnerita de los preconcentrados de la mina Pasto Bueno.

Jun 20, 1954

By Frank L. Wideman

This information circular describes methods used in mining inclined beds of phosphate rock in mines operated by San Francisco Chemical Co. in Rich County, Utah. The mines are on the western flank of the Crawford Mountains, a short, narrow range in northern Utah near the Idaho-Wyoming corner (fig. 1). The western front of the range is a conspicuous wall of folded and faulted sedimentary rocks that rises abruptly 300 to 600 feet above the floor of the adjacent Bear River Valley. Rex Peak, highest point in the range, is approximately 8,000 feet above sea level. The area surrounding the mines is sparsely populated. Randolph, the county seat of Rich County, has a population of 650. It is 10 miles southwest of the mines by road and the only town in their vicinity.

Jan 1, 1958

By Katherine A. Margolis

Refuge Chamber Expectations Training was created by a multidisciplinary team at the National Institute for Occupational Safety and Health (NIOSH) to inform miners of what to expect psychologically and physically if it became necessary to use a refuge chamber in a mine emergency. The presentation can be used either for one large group or for individual miners. The training is a multimedia Adobe Flash presentation containing pictures, audio, video, and interviews with miners who have used a refuge chamber in an emergency. It must be run on a computer with Adobe Flash Player installed (refer to the computer system requirements section).

Oct 1, 2009

By R. Stocker

Flotation recovery of molybdenite particles finer than 15 micrones sharpy decreases with decreasing size. A totally hydrophobic latex agglomerant (UBC-1), which was previously reported to be very efficient in agglomerating hydrophobic fine coal, has been found to agglomerate fine molybdenite particles. The agglomeration takes place only in the presence of MIBC which is commonly used as a frother in molybdenite flotation. Adsorption tests confirmed that MIBC is adsorbed onto molybdenite. The effect of the agglomeration on flotation has been studied by floating fine molybdenite from mixtures with quartz using the UBC-l agglomerant and the MIBC frother. A significant improvement in the flotation of fine molybdenite has been observed in the presence of the UBC-l agglomerant. The best results have been obtained around pH 5.5 which corresponds to the iso-electric-point of molybdenite.

Jan 1, 1997

Mr Chairperson, respected leaders of the mining industry, ladies and gentlemen;   Good morning, Kiora, Nihao.   I am very honoured to give a speech to the 2005 New Zealand minerals conference. I would like to take this opportunity to express my sincere thanks to the Ministry of Economic Development to invite me to be part of this important event.   Today, I am going to talk about two themes: a brief introduction of ChinaÆs economic development, including ChinaÆs energy strategy; the good bilateral relations between China and New Zealand, its potential for further development and its relevance to our cooperation in the field of minerals and energy.   It is a well-known story that over the past 27 years, great changes have taken place in China. In 1978 when ChinaÆs reform and opening up just started, its gdp was near to only 150 billion usd dollars. By the year of 2004 it reached to 1.6 trillion usd, an average of yearly growth rate 9.4 per cent.   ChinaÆs great achievements are widely appreciated both in China and abroad. ChinaÆs development has not only improved the living standard of its own people, but also produced a huge market and brought about great opportunities for the world. Since ChinaÆs entry into WTO in 2001, China has imported near to 1.8 trillion usd dollars of goods, averaging a yearly imports of 500 billion usd dollars, creating for other countries and regions more than ten million jobs.   Our prediction is that in the next five years, ChinaÆs imports will be well over three trillion usd dollars. China will continue to serve as one of the leading growth engines for the future world economic development. Now China is on its great strive to achieve the goals of improving living standard for all the Chinese people. We are trying to reach a quadruple gdp of 2000 by the year of 2020, namely to reach gdp four trillion usd, a gdp per capita 3000 usd dollars.

Jan 1, 2005

By A. E. Gran

"QIT -Fer et Titane Inc. currently produces and markets four main products: a titania slag named SORELSLAG for the white pigment production, a high purity pig iron known as SOREL-METAL mainly used in the ductile iron casting industry, an ilmenite ore for blast furnace applications called SORELFLUX and high quality steel billets SORELSTEEL employed in the wire rod fabrication. Moreover , QIT also manufactures high quality iron and steel powders labeled ATOMET for the powder metallurgy industry through its wholly owned affiliate. Quebec Metal Powders Limited. The company operates. rock ilmenite mine near Havre St. Pierre and produces its slag and ferrous products from its metallurgical installations located in the Sorel/Tracy region. QIT. born in 1948 from a joint-venture between Kennecott Copper Corporation and New Jersey Zinc Company, was acquired from BP Minerals by RTZ Corporation PLC in 1989 and remains its wholly owned subsidiary ever since.lImenite is a mineral rich in both titanium and iron oxides. QIT's proprietary mineral enrichment and electric smelting processes permit the concentration of the ilmenite ore and the separation of its main constituents to produce a 80% TiO2, slag and a high purity molten iron which is further transformed into iron ingots (pigs), steel billets, iron and steel powders.QIT's ilmenite deposit is located in the Lake TIo-A1Iard area, 43 km inIand from Havre St. Pierre, a community on the north shore of the St. Lawrence River some 960 km from Montreal. The orebody, covering some 542 000 m2, consists primarily of coarse-grained ilmenite (FeO.TiO2) with disseminated fine lenses of hematite (Fe2O3). The worthless mineral (gangue) associated with ilmenite is mainly anorthosite, a complex silicate. QITs mining operations are carried out using conventional open pit methods in a 500 m by 600 m horse-shoe shaped mine with nine benches developed. Primary blasting is performed on a weekly basis during the mining season. Blasted ore is trucked to the crushing station to be broken down to 15 cm and 7.5 cm sizes, respectively, by means of a primary jaw crusher and a secondary cone crusher. Minus 7.S cm ilmenite is then loaded into hopper cars for the 43 km trip to the Havre St. Pierre terminal where it is stockpiled and reclaimed by under-ground conveyor chutes to a ship loading tower at the dock. The crushed ore is shipped to QIT's smelter located in Sorel in 40 000 tonne carriers from April to December."

Jan 1, 1995

By C. Caballero, A. Warczok, K. Itagaki, A. Moyano, J. Font

The Codelco Norte Smelter process 2,500 tpd of arsenic-bearing concentrates with an arsenic content of up to 1.5% in one of its two main smelting units, the Teniente Converter. The product, 1,100 tpd high-grade matte or white metal, is traditionally fed to the PS converters, while the 1,700 tpd of slag is fed to the slag cleaning electric furnace for copper recovery. This is achieved in a very reductive environment which reduces the viscosity of the slag and enhances the sedimentation of the high-grade matte droplets. The behavior of arsenic in this non-oxidative environment was studied at lab-scale and fundamental thermodynamic data were obtained. Based on these data a thermodynamicbase model to assess the arsenic behavior in reductive environment was developed. It is based on a mass balance for the reduction and sedimentation stages performed in an electric furnace which allows the recovery of high-grade matte droplets after decreasing the viscosity of the slag. This model can be a very suitable tool for predicting fractional distribution of arsenic in the slag cleaning electric furnace, when the distribution ratio, vapor saturation degree, temperature, y As and pO2 are given.

Jan 1, 2007

By M.E. Crump

Gallium occurs at above background levels in most samples collected from 11 of the major geothermal areas in the Taupo Volcanic Zone. Concentrations of Ga in the 48 samples ranged from 8 to 144 mg kg-' and varies widely from place to place within each geothermal area. Gallium is contained within the alumino-silicate structure of clay in the mud, having substituted mainly for Al. Suggested deposition mechanisms for Ga also involve co-precipitation with Sb, As, and SiO. colloids. Digestion trials, carried out to determine extraction conditions for possible commercial exploitation, showed that heating the mud to 500 -600¦C for 1 hour followed by acid/alkali treatment gave complete recoveries.

Jan 1, 1995

Gallium occurs at above background levels in most samples collected from 11 of the major geothermal areas in the Taupo Volcanic Zone. Concentrations of Ga in the 48 samples ranged from 8 to 144 mg kg-1 and varies widely from place to place within each geothermal area. Gallium is contained within the alumino-silicate structure of clay in the mud, having substituted mainly for Al. Suggested deposition mechanisms for Ga also involve co-precipitation with Sb, As, and SiO2 colloids. Digestion trials, carried out to determine extraction conditions for possible commercial exploitation, showed that heating the mud to 500 - 600¦C for 1 hour followed by acid/alkali treatment gave complete recoveries.

Jan 1, 1995

In the hard rocks of the Nordic countries of Norway, Sweden and Finland underground works have a long tradition. Today the subsurface has been taken into use for a wide variety of purposes. In this paper only the more uncon- ventional examples are described such as caverns for drinking water, sand bunkers, molasses silos, wine and liquor stores, cold stores, heat storage, waste disposal and state archives. The particular use of unlined high pressure tunnels and socalled air-cushions for hydropower schemes is discussed. The dual use of subsurface air-raid shelters for sports activities seems to be a special Nordic tradition. Some cost figures are given and the advantages of using the underground is Discussed.

Jan 1, 1987

By S. Chama, K. Nyirenda, J. Machona, P. W. Chishimba, S. Parirenyatwa, G. Kaluba, Y. R. S. Hara, D. M. Musowoya

Our study focuses on upgrading of copper and cobalt from the Democratic Republic of Congo tailings, containing 2 wt% Cu and 0.5 wt% Co. Cobalt is in the complex iron silicate matrix such that its recovery by direct leaching is not possible. Two concentrating methods were employed in order to obtain copper and cobalt concentrates. Copper was concentrated via flotation and, at the optimal conditions its grade in the concentrate was 31.9 wt%. Cobalt was concentrated to 8.6 wt% b ycarbothermically reducing the flotation tailings with coal in a temperature range of 800–1050 °C and followed by magnetic separation. The reaction products were analysed by atomic absorption spectrometer (AAS) and scanning electron microscopy (SEM) techniques. The best carbothermic reduction temperature was found to be 950 °C due to maximum metallisation and less sintering between gangue and metallic/alloy phases.

Mar 1, 2017

By Freeman C, Dingley W

Addition of sodium nitrite-borax, sodium hydroxide, sodIUm carbonate, lime, or sodium silicate reduced wear of forged steel balls and cast iron slugs in wet grinding a complex zinc-lead-copper sulphide ore in laboratory ball mills. Maximum wear reductions were 27 per cent (forged steel balls) and 33 per cent (cast iron slugs) with sodium hydroxide and nitrite-borax additives respectively.Potential measurements of balls and slugs during grinding, and analysis of the data in terms of corrosion theory demonstrated that corrosive wear had been reduced or prevented by these additives. Actual per cent wear reductions were not equated to the rate of corrosive wear because of the undefined interdependence between abrasion and corrosion in wear processes. The investigation verifies that in laboratory ball mills corrosion is significant in the wear of grinding media and wear can be reduced by corrosion inhibition and pH adjustment.

Jan 1, 1978

By C. G. Goetzel

Until recently porous bronzes have found many applications for self-lubricating bearings in the automotive, electrical, household appliance and general machine industries. The bulk of an annual production of several million pounds of copper powder had gone into the manufacture of these articles, of which by now more than a billion are in service. However, the war has brought severe curtailment of these bearings because of the scarcity of the two main constituents, copper and tin. The development of substitute materials of equal or superior properties has led to a large-scale replacement by products made from iron powder. In spite of the diminished interest in powdered copper-tin alloys caused by this trend, it was believed worth while to investigate some mechanical properties of these materials as a reference base for substitutes. In addition, experiments using the hot-press method were incorporated to investigate possibilities of saving vital equipment or opening new fields of applications. It must be assumed that by this time the powder metallurgy process of making porous bronzes, a development that found its first industrial applications more than 10 years ago, is well known in engineering. The patent literature and bibliography is volu- minous, most publications referring to porous, self-lubricating bronzes, containing about 10 per cent tin and I to 5 per cent graphite, with porosities in the range of 25 to 35 per cent.l-7 The excellent antifriction properties of these bearings, caused by the uniform impregnation with oil, are dependent on the interconnection of the pores and the uniform distribution of the graphite inclusions. The sintering mechanism of porous bronze, with its structural changes during the transformation of the metal powder into the sintered bearing has been shown in colored photomicrographs by Hall.* Diffusion between copper and tin was found to begin within one minute, when tin-rich transitory phases were formed. After 25 min. a homogeneous matrix of alpha was reached for an alloy containing 9.5 per cent tin and 6 per cent graphite. Price, Williams and Garrand,9 studying certain metal powder combinations in which sintering is accompanied by the cementing action of a liquid phase, including a 90-10 bronze sintered at 925°C., have found that if the treatment is carried out within the liquidus and solidus temperature range of the system, a peculiar process of alternate solution and precipitation occurs. The particles of the major solid constituent are dissolved in the minor liquid phase, but thereafter are reprecipi-tated on certain nuclei, which develop into large grains, usually rounded.

Jan 1, 1945

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

PRESIDENT LITTLEJOHN: I have every reason to know Mr. Pryde was carrying out some experiment a while ago in some of his mines. He and I had a little correspondence on the question, and I think he may have a word or two to say about it. He has not been on his feet today at all. I will ask Mr. Pryde to tell us what he has to say. MR. PRYDE: I have not very much to say about shooting coal with permissible powder as far as slack is concerned because we are not in the commercial business. All of our coal goes to the railroad and a very large part of it is crushed for use in the stokers of the locomotives. We are on a 100 per cent permissible powder basis and as far as I am able to see, I do not believe that the percentage of slack is increasing with its use. We find it hard to convince our commercial neighbors of this fact because they are naturally very much against increasing their percentage of slack on ac- count of the low price received for this grade of coal. I, personally, believe that where a change is made from black powder to permissible powder the percentage of slack will be increased for a time because the miners have been accustomed to using black powder and they are rather suspicious about going to the permissible powder and I do not believe that we can blame them very much. So the tendency with them is to use too much powder. We have gradually overcome this, although, as I said before, we have not kept close track of the production of slack. However, we try to get as large an amount of lump coal as possible. Broadly speaking, I can say from observation that in my opinion there is very little difference in the percentage of slack with the use of the permissible powder that we have today than there was with the use of black powder. I also get this information from our mine superintendents. Mr. Peterson and the other explosive men have been very helpful to us in the use of permissible powder and I confess I have to take everything back that I said several years ago. At that time I was against permissible powder, particularly on account of the cost, but, with the newer permissible powder, we have gotten the cost down very well. I know today that the cost of permissible powder in the coal mines of the Union Pacific Coal Company is less than when we were using black powder. I know this because of the fact that we kept a record of the number of tons we got with black powder, and the number of tons we get with permissible powder compares very favorably in cost. I know this, too, because of the fact that our employes, except in the first few weeks of using permissible powder, have made no demand upon us for any in- crease ill pay to offset any added cost that might accrue in the use of permissible powder and the fact that they have asked for no increase is very conclusive proof to me that it is not

Jan 1, 1925

By Lyon F. Terry

INCREASING domestic demand for products, a sharp reduction in exports to Europe, and a rise in imports from South America were the chief features of the economic side of the industry in 1940. As the war progressed it became evident that exports to former European customers were being cut off or drastically reduced, leaving heavy inventories of products in the hands of many American refiners who had anticipated larger demands from the belligerents. Stocks of motor fuel reached burden-some proportions early in the year for the added reason that refining operations were stimulated by heavy demand for heating oils. Excessive tanker rates for Gulf to Eastern Seaboard movements during the first part of 1940 contributed to the accumulation of products on the Gulf Coast, where refinery gasoline prices were forced to extremely low levels by midyear. Tanker rates receded to normal during the summer but have since risen again to the approximate equivalent of pipe-line tariffs from the Mid-Continent.

Jan 1, 1941