Search Documents

By D. W. H. Su

This paper presents the results of ill situ horizontal stress measurements using a Minifrac system in several northern Appalachian coal mines. The effect of stress magnitude and orientation on longwall gate entry stability was analyzed using a series of three-dimensional finite element analyses. The best headgate stability is achieved if the maximum horizontal stress is aligned with the direction of longwall retreat or if the panel is oriented such that the maximum stress relaxes over the headgate due to the presence of the newly formed gob. The degree of horizontal stress damage to longwall gate entries depends largely on the stress magnitude and roof geology. Accurate assessments of support or design techniques which may mitigate longwall headgate or tailgate instability in areas of thinly laminated roof and high horizontal stresses must account for the in situ horizontal stress state and site specific roof geology. The ability to measure stresses and map geology is thus essential to prevent ground control failures at the longwall headgate.

Jan 1, 1995

By J. S. Kirkaldy, W. V. Youdelis

THE occurrence of concentration distributions in rapidly cooled castings with gradients of opposite sign to those expected on the basis of the constitution diagram and diffusion controlled kinetics, has long interested metallurgists. The work on inverse segregation to 1937 has been adequately reviewed by Vaughan, and to 1949 by ell-walpole. The general conclusion for unidirectional solidification, that the enrichment of the initially solidifying regions with lower melting point compositions is due to the flow-back along interdendritic channels of normally segregated residual liquid, has a very sound experimental basis. Perhaps the best experimental work and the most complete qualitative description of the process has been given by Adams.3 The authors accordingly assume the reader's understanding of the content of this paper. It appears that one of the principal deterrents to the complete understanding of the process has been the lack of an analytical description. Although a number of workers including Masing,4-6 Sauerwald,7 and Adams3 have attempted quantitative predictions,

Jan 1, 1959

The movements of the major continental cratons and the distribution of the principal tectonostratigraphic terranes are reviewed in the Circum-Pacific region during Phanerozoic time. It is concluded that major periods of orogeny and consolidation of accreted terranes in the Circum-Pacific region is best correlated with periods of advance of cratonic blocks over the Pacific Ocean basin combined with relative convergent to transpressive motions between the cratons and the Pacific Ocean plates. Continental collisions and collision of terranes with continental margins has not been a significant geodynamic process in Circum-Pacific tectonic evolution. The permanency of the Pacific Ocean basin throughout 500 MA is remarkable. It appears no continental block or large continental fragment has ever entered or crossed the Pacific Ocean basin since early Paleozoic time. This area where no continent has entered for 500 MA is almost coincident with the present Pacific Ocean basin and seems associated with the 25 to 100 meter geoid high which dominates the present-day figure of the Earth.

Jan 1, 1990

By David E. Siskind

The Bureau of Mines has studied the fracturing produced in the vicinity of large-diameter blastholes in Lithonia granite. Cores were taken from the vicinity of AN-FO production blasts and examined using a total of seven laboratory and field measurement techniques to delineate zones of damage and evaluate the effectiveness of the seven diagnostic tests for fracture-state determination. Laboratory measurements of acoustic pulse velocity, porosity, permeability, compressive strength, and Young's modulus indicated the extent of fracturing with the acoustic techniques providing the best means of distinguishing between fractured and unfractured core. A severely fractured zone was found to extend approximately 25 inches (64 cm) from the center of the 6-l/2-inch blastholes, equivalent to 8 blast-hole radii. A second zone, characterized by a lesser degree of fracturing extended from 25 to 45 inches (64 to 114 cm) or 8-to l4-blasthole radii. Beyond 45 inches (114 cm) the rock was undamaged.

Jan 1, 1974

Jan 1, 1901

The cyclone, or centrifugal separator, ,is firmly established in industry as a low cost separator of solids from gases.While it will also separate fluids of different densities, and solids from liquids, its main use is to remove relatively fine dusts from gases whose pr~erties are generally not greatly different from those of air. This latter phase of operation is the one that will be dealt with here.The duty of such a cyclone separating system is to take in a supply of dusty gas and separate it into its components of dust and clean gas as perfectly as possible for the least consumption of pressure head. Any separation at all causes pressure loss and, in general, the greater the separation, the greater the pressure drop needed to effect it. The percentage of dust in suspension which is separated from the gas-dust mixture is commonly called the collection or separation efficiency. Overall or "true" efficiency must take pressure drop into account and may be considered as proportional to the ratio of the percentage of dust collected to the resultant pressure drop. For any cyclone It will vary with different dusts.Many commercial adaptions of the simple cyclone are made solely on the basis of pressure drop improvement, without taking into account the effect on separation efficiency, probably because the latter is so difficult to assess correctly. It appears unfortunate but true that the majority of such adaptions and patent gadgets fitted to cyclones which decrease pressure drop, do have an adverse effect on separation. In other' words, the true efficiency is seldom increased but often diminished.Without a knowledge of what actually goes on inside a cyclone, it is impossible fully to appreciate the real effect of a modification. For instance, it is on record that a cyclone...

Jan 1, 1949

By John E. Miller

Supercompressibility factors, Fpv, were derived from experimental compressibility data for five helium-nitrogen mixtures containing from 50 to 100 pct helium. These Fpv values are required as volumetric correction factors for or if ice meter measurement of "crude helium" (helium-nitrogen) purchased by the Government in a program of helium conservation. Although compressibility measurements were made by the Burnett method (2)3 - for pressures from 100 to 3,400 psia and temperatures from 40° to 100° F, Fpv values were needed only for pressures from 400 to 2,000 psia. Consequently, values at increments of 2° F, 2 pct helium, and 10 psia were tabulated only for the required pressure range. Values for pressures outside this range can be calculated from information shown in the tables. Values for the second, third, and fourth coefficients in the equation Z = 1 + BP + CP2 + DP3 are also included.

Jan 1, 1963

By Klaus Schönert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such sub-processes as: (i) The transportation of the particles to the zone where they are stressed, (ii) The stressing of the particles to a level high enough for breakage, (iii) The removal of the fragments that are smaller than the limit size from the grinding zone, and (iv) The prevention of agglomeration of the fine fragments. The breakage phenomena of particles is the most difficult sub-process to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. It is not only of academic interest to know how a particle breaks, but also it is important for practical applications because it provides a basis for evaluating both the direction and limitation for any potential comminution improvement.

Jan 1, 1971

By AIME AIME

THE annual session for the election of officers and transaction of other official business of the Institute, which must be held, in accordance with the By-Laws, in New York on the third Tuesday in February, was the only session scheduled for the morning of Feb. 19. Many members gathered in the auditorium at 10 o'clock, and President George Otis Smith presided. He said that his report was best set forth in the reports of the other officers and committees, which were avail-able in printed form. Productive activity had characterized the Institute's year and a number of new ventures had been successful. He felt that he had "rattled around" in the office of president, as he had traveled some 39,000 miles during the year in visiting the various Sections, having visited everyone that had held a meeting during his term of office. He spoke of the educational effect on a president of these broad contacts and suggested that a three-year course would be even more enlightening than one.

Jan 1, 1929

By Hongbo Yang, Tongbo Zhang, Ting Huang, Jingshe Li, Fangfang Song

"Liquid core length is a very important parameter of the process of continuous casting, which directly reflects the cooling status in secondary cooling zone and solidification rate of the slab. In this paper, the billet caster in some steel plant in China was chosen as the prototype of simulating. A numerical simulating model for calculating the liquid core length of continuous casting billet was built by ProCAST software, which was verified reasonable and accurate by pin-shooting technique. Based on the model, the relationships between casting speed, casting temperature and liquid core length of casting billet were found, which was very practically useful for the workers on sit to improve casting billet quality. IntroductionContinuous casting process developed very rapidly because of the high metal yield, energy saving, and low-cost 111• And the quality requirements of continuous casting billet for customers became higher and higher with the fast development of economic121• Internal defect usually is the major quality problem for continuous casting billet[3•61 , which is influenced by the solidification process of casting billet, especially the solidification process of liquid core17•81 • So it is very important to study on the relationship between casting parameters and the liquid core length which means the distance between the crystallizer meniscus and the casting billet solidification end-point. In practical production process, the workers usually control the quality of casting billet according to the liquid core length."

Jan 1, 2013

By AIME AIME

THE steel industry has always been noted for producing men of forceful and versatile personality, many of whom combine the practicality that results from wide experience with an excellent theoretical background that comes from a college training plus years of wide and constant study of metallurgical literature. One of the best known examples of this type is Earle C. Smith, present Chairman of the Iron and Steel Division. After graduating from Ohio State and from Columbia, where he studied under Campbell, Earle started his career at that grand old prewar training school for steel men the Illinois Steel Co., where in the days of the twelve-hour shift he worked on the open-hearth floor. Following World War I, when he was in charge of government inspection at the Central Steel Co., Massillon, Earle held successively jobs of increasing responsibility with Central Alloy Steel, and when this company was taken over by Republic in 1930 he was made assistant district manager and a few years later was appointed chief metallurgist of the whole corporation.

Jan 1, 1942

By E. G. King

This paper reports measurements of low-temperature heat capacities and entropies at 298.15° K. of two copper ferrites (CUFe204 and CU0.75Fe2.2504). These substances, which occur in copper-smelting slags, have not been sujected to any previous direct thermodynamic investigation. The two copper ferrites are spinel minerals of the variate class. In previous investigations similar data were obtained for 13 other spinel minerals -7 of the normal class and 6 of the variate class. The entropies at 298.15° K. of these minerals have been compiled and revised as necessary in the light of present knowledge regarding structural randomness; entropy values, recommended for use in thermodynamic calculations, are listed.

Jan 1, 1959

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014

By Tadafumi Adschiri

"Supercritical water can provide an unique reaction atmosphere for synthesizing metal oxide nanoparticles. Due to the drastic change of properties of water around the critical point, including density, dielectric constant and ionic product, the reaction phase with O 2 or H2 gas and the reaction rate and equilibrium can be varied to synthesize new materials or define particle morphologies. In this work, hydrothermal crystallization experiments are performed with several types of flow apparatus that allow convenient manipulation of variables such as temperature, pressure, and residence time. Key features in the flow modes and material preparation are discussed. The proposed supercritical hydrothermal synthesis method has the following desirable features: i) nanoparticles can be produced, ii) morphology of the produced particles can be controlled with small changes in pressure or temperature, and iii) a reducing or oxidizing atmosphere can be applied by introducing oxygen or hydrogen or other gases. An overview of this method is given for functional material synthesis of significant industrial interest including barium hexaferrite magnetic particles, YAO/Tb phosphor fine particles and lithium cobalt fine crystals.IntroductionHydrothermal crystallization, a method of metal oxide formation from metal salt solutions, is typically used at temperatures ranging from 373 K to 473 K. We are developing a new process for hydrothermal crystallizations that uses temperatures in the range of 673 K to 723 K, which is just above the critical temperature of water1 • 8 • In this work, we refer to this process as supercritical hydrothermal synthesis. The supercritical state of water allows one to vary reaction rate and reaction equilibrium by shifting the dielectric constant and solvent density with pressure and temperature. From of our research on material production in supercritical water, we have identified the following specific features of the supercritical hydrothermal synthesis method: (i) ultrafine particles can be produced, (ii) morphology of the produced particles can be controlled to some extent with pressure and/or temperature, and (iii) a homogeneous reducing or oxidizing atmospheres can be provided by introducing gases, such as O 2, H2, H2O 2• and so on.1"

Jan 1, 2000

By Ruirui Wei, Yanhui Liu, Fangqing Yin, Meilong Hu

In China, Basic Oxygen Furnace (BOF) slag is traditionally used as an aggregate for civil engineering, for road engineering and fertilizer. In order to make full use of BOF slag, the experiments of BOF slag with high temperature roasting has been carried out and the phase transformation is studied. The BOF slag from Chongqing Iron & Steel is roasted in the electric muffle furnace at three different temperature. The influences of the high temperature roasting on change the phase composition of BOF slag was characterized by XRD. The results revealed that SFCA was produced at the high temperature in air atmosphere and melting temperature of slag was lowered. Therefore, if the BOF slag which treated by roasting was utilized in the sintering process, it is advantageous to improve the sintering strength and the formation of the liquid phase and reduce fuel consumption in the sintering production process.

Jan 1, 2015

By Pierre Laliberté

Introduction ??Mine ventilation is a major consumer of power in underground mining, including air heating (winter) and air conditioning (deep mines). ??Any advances, including the development of low emission vehicles, that can improve underground air quality can reduce ventilation demand, and likewise reduce costs and energy consumption, including their associated greenhouse gas emissions.

Nov 1, 2011

By Michael Loken, April Montera

"The process of blending consistent and predictable feed for the roasters is critical to optimizing product quality and controlling production costs. To assist in this process, Online PGNAA Slurry Analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100% of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their Full Stream, Elemental Slurry Analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced."

Jan 1, 2016

By L. S. Trenholme

"Belleterre Quebec Mines, Limited, is a subsidiary of Mcintyre Porcupine Mines, Limited. The property is in Guillet township, Quebec, 45 miles due east of Haileybury, Ontario. It is accessible by 72 miles of gravelled road from New Liskeard, Ontario (Fig. 1).Gold production at the property commenced in 1936 and to March 31st, 1945, had exceeded $9,000,000. For the past 3 years the milling rate has averaged 325 tons a day and the gold recovery about $14 a ton.GENERAL GEOLOGYThe rocks of the district consist of Keewatin-like volcanics conformably overlain by Timiskaming-like sediments. Together they form the remnant of an easterly plunging anticline engulfed by granite (Fig. 2). The pregranite intrusives consist of diorite, gabbro, and ultrabasic rocks, occurring as dykes, sills, and irregular stocks. Dykes of porphyry and lamprophyre presumably related to the batholithic intrusive are common in this area. The veins of quartz are also probably derived from the batholithic intrusives. A few dykes of Keweenawan-type diabase have been observed."

Jan 1, 1954

By John Malcolm Gray

Interest in X-80 linepipe steels emerged in the early 1980’s and it was first used in 1985 by Ruhr Gas [1]. The early steels were extensions of conventional Nb-V or Nb-Mo microalloyed X-70 steels but other alloying concepts emerged based on Nb-Mo-B alloying (NKSTAF [2] and ULCB [3]). The latter had acicular ferrite/bainitic microstructures and carbon contents below 0.05 percent. In parallel renewed interest developed in ultra low carbon (0.02 percent) higher niobium steels which had first been studied in 1962 [4]. Such steels exhibited excellent notch toughness when processed with high finish rolling temperatures (>950°C) which made them suitable for processing on weak, older rolling mills. With time such steels, designated “High Temperature Processed”, or HTP steels, were further optimized and produced in modern, very strong rolling mills due to their superior economy compared with traditional vanadium and molybdenum containing steels. The chronology of the HTP development is presented in the present paper. Full scale demonstration heats of a 0.06 percent carbon 0.10 percent niobium steel were produced by Bofors Steel Plant in 1972 and were converted from slabs to plates by nine different steel mills [5-7]. Commercial application in API Grade X-70 first occurred in Canada in 1974 [8,9] but the concept was only used sporadically after that until 1998 when it was applied for the API Grade X-70 Sour Service Cantarell Project [10] in Mexico. Soon thereafter, the El Paso Cheyenne Plains Project used a 0.05%C 0.095%Nb 0.27%Cr variant of the HTP steel [10-12]. Nowadays the HTP concept is being utilized for construction of approximately 6000 km of 48” OD x 18.4 mm X-80 per year in China. The metallurgical principles and history of the development are presented in details in this paper.

Aug 7, 2018

W. P. PUTNAM,. Detroit, Mich.-There is one company that is heating these tubes in an upright position by passing electrical energy directly through the tube itself. The lower connection is attached to an indicator, which shows the point at which the steel passes through the critical range At that point the clamps are released and the tube is dropped into a well of oil. This method simplifies the heat treatment of tubes in long lengths. H. J. FRENCH.-I am not entirely familiar with. the method outlined, but it appears to have one serious disadvantage; that is, the length of tubing that is directly connected with the electrical contacts is wasted and must be cut off due to either heavy oxidation or burning. That is a serious difficulty, if true in all cases, and cannot be overcome, inas-much as it is very difficult to draw long tubes of thin wall. Having once obtained a lot of tubes, to cut, say 14 ft. in length, there is often little excess metal available to discard. Am I correct concerning the burning or heavy oxidation of the metal where it comes in contact with the tube.

Jan 12, 1919