Search Documents

By Harry Thompson

In using explosives to blast stumps from the ground in order to prepare it for farming, it is comparatively easy to place the charge under a stump having a semitaproot or a lateral system of rooting by boring or digging a hole in the earth to a point under the center of resistance and deep enough to give the desired effect.1

Jan 1, 2015

By H. Oda, L. E. Fong, K. K. McBride, B. P. Weiss, F. J. Baudenbacher, A. Usui

Fine-scale dating is a key parameter in characterizing the growth history of hydrogenetic ferromanganese crusts. We once compared several dating methods, micropaleontological (calcareous nanofossil), radiometric (10/9Be), and paleomagnetic (step-wise measured inclination) methods on single samples, but these independent methods were not consistent with each other (Joshima & Usui, 1999). For example, a 4-cm thick crust was dated as 3Ma by the fossil-paleomagnetic combined method, while it dated older than 5.5 Ma by Be-10 dating. This discrepancy suggests a question if the Be-10 radiometric method can give us false ages or growth rates (Usui et al., 2002) because of post-depositional change, diffusion or other reasons. In order to answer the question, we conducted ultra-fine magnetostratigraphy with a SQUID microscope on the same hydrogenetic Mn crust sample. Rock magnetic measurements revealed that the main magnetic mineral is well dispersed single domain grains, which is typical to magnetite but not yet specified (Oda, 2005).

Aug 24, 2006

By T. R. Kostecki, J. Hirschi

"Analytical engineering design is based upon a trial-and-error iterative and deterministic process. Within this process, the engineer obtains some estimated values, plugs them into de facto closed-form equations, and receives output, which is expected to be a single number that serves as the basis for the design. This number is typically a factor of safety, or some other equivalent strength-stress ratio. This provides the engineer with a quick and relatively quantitative design methodology. This can create problems however, because in mining applications, the actual in situ system is highly variable, complex and often chaotic, which can lead to potentially incorrect conclusions that result in unsafe designs. A more appropriate and reliable approach is a probabilistic analysis for engineering design. This process is used widely in civil and other engineering disciplines, but is often overlooked for applications in coal mine design. Additionally, it seems the amount of past studies using this approach, especially in coal mine design, are rather limited. Considering how the probabilistic approach can account for uncertainty in parametric values and how unpredictable a mining design can be, the authors believe that this approach has potential in mining. This paper will focus on a summary of past studies related to probabilistic analysis in coal mine pillar design and provide recommendations for future work that could improve design reliability. INTRODUCTIONFeasibility and fundamental design procedures for excavations often start with an assessment of mine openings, pillar design, and the surrounding structure by using a deterministic approach with closedform solutions (ex. Bienawski, Obert-Duvall). These are reliable methods, but designers know that the inputs in these closed-form solutions are estimates at best and do not incorporate any degree of uncertainty. This is therefore not an optimal design procedure.A more appropriate design should incorporate some uncertainty because of the chaotic and variable nature of geology and mining conditions in general. In an attempt to account for uncertainty, a probabilistic approach can be adopted, which accounts for deviations in variables and provides a more optimum design solution. By applying a probabilistic approach, a designer can look at multiple failure scenarios at the same time instead of using the same deterministic design over and over."

Jan 1, 2015

By Satyajit Vaidya, Rudolph Frizzi, Sandy Larimer

"This paper presents a case history in design and construction of a deep foundation system that included high-capacity open-ended driven piles constructed to support a high-rise building in Manhattan, New York. The project site is bordered by existing buildings, active streets, and critical public transportation infrastructure, which were considered in the new building’s deep foundation and seismic design. This paper focuses on driven pile foundation design and installation through relatively loose soil deposits. Unique design aspects included seismic design considerations, and pile splice design for open-ended steel pipe piles subject to significant uplift and lateral loading. Unique construction aspects included quality assurance of open-ended steel pipe pile splices, and uplift and lateral load testing of driven piles installed in close proximity to other foundation elements installed for the project.SITE CONDITIONS AND SUBSURFACE CONDITIONSThe project site is located in Manhattan, New York, and is bordered by existing buildings, active streets, and critical public transportation infrastructure that is located about 60 feet from the site. The existing sidewalk grades around the site are between about el 4 and about el 13; elevations are referenced to the North American Vertical Datum 1988 (NAVD88).Subsurface conditions at the site generally consist of successive strata of historic fill, former river bottom deposits consisting of compressible clayey soils, and medium dense to dense sand, overlying mica schist bedrock. A generalized subsurface profile is shown in Fig. 1. The historic fill stratum is about 10 to 45 feet thick, and generally consists of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick, concrete, and glass fragments. The underlying former river bottom deposit stratum is up to about 15 to 20 feet thick, and generally consists of very soft to very stiff clay and lenses of very loose to loose sand. Medium dense to dense sand was generally observed below the historic fill and former river bottom deposit strata and overlying bedrock. Top of bedrock was generally observed at about 80 to 105 feet (i.e. at about el -75 to el -100), except in the southeastern portion of the site where the top of rock was observed as deep as about 140 feet (i.e., at about el -135). Groundwater levels typically ranged between about el 1.5 and el -0.5."

Jan 1, 2016

By M Coleman

Information is a key ingredient for successful mineral exploration and development. Whether identifying potential exploration localities from a map, interpreting technical reports or searching a register for operators past and present, the common aim is a parcel of information from which the enquirer can make a decision. Traditional information gathering often requires days or weeks of manual research, studying maps, files, reports etc, before consolidating the results into an investment proposal. In recent times, such methods have largely been replaced by Information Technology, making the process much faster, easier and more centralised. However, notwithstanding some very successful technology implementations, the general rush to computerise everything in sight has left many organisations struggling to cope with the management of large volumes of diverse information. Information management is now recognised as the most important factor in determining the success of information technology implementation. The Northern Territory Department of Mines and Energy (DME) has established a detailed information management strategy to underpin the rapid advance of computer technology within the organisation. A broad base of timely and reliable information is gradually becoming more accessible. It is envisaged that the availability of combined spatial, textual and scientific information will provide a sound basis for decision-making within the Department and the mining industry at large. Although information held by DME will be available at all times (24 hours on-line), its security and confidentiality will be guaranteed. The production of the DME system is aimed at satisfying the corporate objective to facilitate and promote mineral exploration and development. This paper outlines some current developments in the system.

Jan 1, 1994

By G. Nash

Despite further declines in production for some producers, 1986 proved to be a landmark year for the asbestos industry. The key event was the adoption of The Asbestos Convention by the Inter- national Labour Organization (ILO) and its 150 member countries. The document, entitled "Safety in the Use of Asbestos", reaffirms the international consensus on the "controlled-use" approach to chrysotile asbestos regulation. The decision of the ILO has come at a critical point in time. It represents a major turning point and provides an important building block for the long term future of the asbestos industry.

Jan 1, 1987

By Ted Klemetti, Gabriel Esterhuizen, John L. Ellenberger

"Advanced numerical models can be used to evaluate entry support systems in coal mines. However, these methods require specialized software and specialized skills to create the models and evaluate the results. Practicing support design engineers require a method to rapidly assess a proposed support system for a given geotechnical scenario. A prediction equation that can be used to assess roof support systems has been developed from the results of hundreds of FLAC3D analyses that were conducted during recent research. These models were validated against field cases and empirical design approaches and were found to adequately predict entry stability in coal mines. The understanding developed from the model outcomes was used to develop an equation to predict entry roof stability against large roof falls. Least-squares error analysis was conducted to find appropriate parameters for the nonlinear equation. The developed equation can be solved using spreadsheet software, allowing for rapid assessment of alternative support system performance in variable geological conditions. The performance of the prediction equation is evaluated against empirical design methods and against selected case histories of support practices at currently operating mines. Examples are presented that demonstrate the performance of the equation in variable geological settings. The stability factor (SF) prediction equation can be used as an assessment tool to assist in the design of coal mine roof support systems.IntroductionGround falls represent a significant proportion of injuries and fatalities in underground coal mines in the US. During 2013, ground falls were responsible for 4 of the 14 fatalities and 16.6 % of the 1,577 reportable lost-time injuries (MSHA, 2015). In addition, each year about 400 to 500 large roof falls are reported that can extend up to or above the bolted horizon. Large roof falls and associated ground fall hazards can be mitigated through improved support design.The research presented here particularly addresses the problem of large roof falls that extend more than 90 cm (3 ft) above the roof line of an entry and may extend above the bolted horizon. Smaller roof falls that fall out between supports or extend less than 90 cm (3 ft) above the roof line are excluded. These smaller roof falls can be controlled by appropriate surface support such as roof screen or other skin control methods. Also excluded are roof falls that are associated with an individual geological structure such as a slip of fault. Structure-related instabilities can be controlled by strategically locating individual roof bolts or other supports appropriate for the local situation."

Jan 1, 2015

By Jamey Rosen, Georgette Hlepas

"Bluestone Dam is a concrete gravity structure with an overall length of 2,060 feet and a maximum height of 165 feet above the streambed. Several major project modification designs have been implemented and additional modifications are currently in construction and design phases. Due to the various modifications since original construction was completed in 1948, detailed documentation with visualization of the project features is needed. A three-dimensional model of the internal and external features of Bluestone Dam was generated from LiDAR data, survey information, and other data sources. One of the key features of interest in this model is an accurate visualization of over 200 dam anchors based on downhole anchor surveys. The model is accessible in Microstation and Geographic Information Systems (GIS), allowing users to rotate the anchors in three dimensions; view them in the context of geology, internal dam structural features, historical construction records, site photographs, bathymetric data, and instrumentation data. Users can “click” on individual anchors to view associated construction details and open a comprehensive installation packages. The model will be used by the United States Army Corps of Engineers (USACE) as part of a larger Geospatial Data Management System as a historical accounting of the project construction data, and be a long-term living document for use by both design engineers and operations staff to assess dam safety risk and to design future project modifications.IntroductionDuring the life of any project, critical data concerning the construction and performance history are required to be collected and maintained. The data collected prior, during, and post-project construction help with the design process, ensure that the project is built to specifications and is performing as per design intent. During the Post-Implementation Evaluation (an evaluation performed after a major project modification), these data are used to visualize the repairs, verify the construction was performed per design intent, and document the history of the construction phases, associated test results, and overall effect on the project. The project described in this paper is the construction of a system of tools to effectively use these data.Data collected and maintained during the operations phase helps to ensure that the project is continuing to perform as per design and aids in advance warning of any potential failure or required maintenance. Dam Safety, Emergency Management (EM), and Operations and Maintenance personnel can use the system to verify the status of the project in preparation for a high flood event. For example, if there is repair work being performed on a critical feature of the project that would affect the operation of the dam structure during a flood event, Operations personnel would be responsible to update the status of the system such that Dam Safety and EM would be able to identify the feature that is out of service, its date of expected repair completion, and the implications during a flood. In addition, risk assessments typically require a full history of the project and its performance. Any concerns that arise concerning the safety or performance of a project will require a full documented history of the project and its components. Proper documentation and data management are key in this assessment process."

Jan 1, 2016

By L. J. Barnes, R. O. Koch, J. H. Versteegh, C. J. N. Buisman, P. J. H. Scheeren

Several water treatment options have been studied and piloted. A process based on activity of sulphate reducing bacteria combines sulphate removal and heavy metal removal in one process step. The anaerobic bacteria reduce the sulphate to sulphide and consequently metal sulphides will precipitate. The final design for the commercial scale plant is described.

Jan 12, 1992

By A. G. Starliper, H. Kenworthy

A procedure was developed for the separation of lead and sulfur in industrial concentrates of galena by a combination of chlorination and fused - salt electrolysis . Galena could not be satisfactorily electrolyzed in the various media tried ; however , when it was treated with chlorine the resulting lead chloride could be effectively separated electrically into lead and chlorine . An apparatus was designed and constructed to chlorinate galena and to volatilize simultaneously most of the chloridized impurities . By electrolyzing the chlorinated concentrate , a high percentage of lead was recovered . Anodic chlorine was drawn from the cell and was used to chlorinate new feed . In many runs , the recovered metal analyzed from 99.8 to 99.9 percent lead . Lead was also distributed as a chloride in the bath , and a small portion was in the volatile fraction produced during the chlorination step . During a tinuous operation , only 0.1 percent of the total lead was discarded ; 99.9 percent was accounted for in the metal , electrolytic bath , and washed or leached chlorination condensate which was essentially lead chloride . About 95 percent of the sulfur from the galena was recovered as a byproduct of over 90 - percent grade .

Jan 1, 1964

By Ademar Lopes, Victor Silva, Heitor Silva, Gustavo Usero, Roberto Rolo, Lucas Pereira, Gabriel Moreira, João Lague, Arthur Endlein, Matheus Feitosa

Grade control models are supposed to provide a higher resolution than long-term or interim models. However, available grids from diamond or reverse circulation drilling do not provide that required resolution. In this study, a geostatistical workflow is proposed to integrate available grade data from production blastholes with its operational parameters taken when drilling downhole. The step of geological logging can be replaced by machine learning models for classifying blastholes into lithologies and hardness classes. Next, indicator and ordinary kriging use the classified blastholes and previous data for estimating the model domains and the grades within each one. The workflow is applied in a world class iron ore mine in Brazil.

Jun 25, 2023

By Joseph Cervik

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pet; reductions of 38 to 79 pet were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No.3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By J. A. Innes

"""The oxygen, next uniting with the carbon, sent up an ever-increasing stream of sparks and a voluminous white flame. Then followed a succession of mild explosions, throwing molten slags and splashes of metal high up into the air, the apparatus becoming a veritable volcano in a state of active eruption.""IntroductionHenry Bessemer F.R.S(An autobiography, 1905)Thank you Mr Chairman for the opportunity to speak: at this, the opening session of your International Symposium on the subject of ""Injection in Pyrometallurgy"". Judging from the list of papers to be presented over the next three days, the Symposium promises to provide a most valuable addition to our existing knowledge base in what is now an extremely active area of R&D investigations. Whilst we have obviously come a long way since Sir Henry Bessemer's pioneering experiments of the mid-19th century, there is still much for us to learn.Most importantly, the Symposium offers a further opportunity to acknowledge the many significant technical contributions made in this field by the Organising Committee's special guest, Professor Howard Worner - one of this country's most respected research leaders.When first approached to give this talk I had two areas of concern. Firstly, I was not entirely clear just what injection metallurgy was meant to cover. How should the overall scope of this particular subject be defined?My second concern related to Howard Worner himself - a man for whom I have the highest personal regard and who, in fact, played a most influential role in respect of shaping my own career. Having already spoken about Howard's achievements on earlier occasions, I wondered what I could sensibly add.Notwithstanding these personal reservations, I am delighted to be here with you this morning. If my thoughts on the meaning and scope of injection metallurgy appear to be slightly off-course, and if Howard should perhaps recognise some repetition in my remarks, then I hope I can be forgiven."

Jan 1, 1996

By S. L. I. Chan, M. Z. Quadir, D. C. Austin, P. J. Hazell, A. Chen, A. A. H. Ameri, D. East, J. P. Escobedo, M. A. Bevan, A. D. Brown

The microstructure and mechanical response of additive manufactured Ti64 under compression and tension has been investigated. Quasi-static and dynamic experiments were conducted on electron beam powder bed Arcam A1 (EBM) and blown powder laser Optomec LENS MR-7 (LMD) additive manufactured specimens. Hot isostatic pressing (HIP) was conducted on both of the additive manufactured specimens and results were compared with as-received specimens. Digital image correlation (DIC) was utilized to observe the in situ development of deformation fields during tensile loading. Optical microscopy was conducted on pristine and deformed specimens to examine the microstructure of the specimens. HIP treatment reduced the porosity by *90% with a concomitant increase in hardness by 40%. The results from tensile experiments show that additive manufactured Ti64 display a higher values for the yield stress, hardness, and ultimate tensile strength than conventionally manufactured Ti64. Under quasi-static compression, it was observed that EBM specimens exhibit a higher yield strength and ultimate tensile strength than LMD specimens.

Mar 1, 2017

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

By S. A. Scott

In 1913, potash mineralization was recognized at a depth of over 7,000 feet in an oil-well hole (Norcanol's Radville No. 1 well) drilled near the town of Raddlle, Saskatchewan. Although, at this depth, potash is not considered mineable by conventional underground mining methods, this discovery shed the first light on the potash deposits of Saskatchewan in much the same manner as oil-well drilling was responsible for the first discovery of potash in the Carlsbad Basin of New Mexico in 19:25. The discovery near Radville alerted the oil-well geologists and, as a result potash mineralization was recognized in the Verbata No. 2 well, near Unity, Saskatchewan, in 1946. The mineralization, which was at a depth ?of 3,466 feet, graded more than 20 per cent K20 over a thickness of eleven feet. This discovery, as its depth, thickness and grade were all amenable to mining,

Jan 1, 1963

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The University of Kentucky employs an explosively driven shock tube in the course of experimentation. A good deal of the work completed relates to the verification of blast mitigation products and strategies. The work is dependent upon reliably reproducing specific pressure time histories called out by the test in question. The facilities are located in the workings of an underground limestone quarry in Georgetown Kentucky. As such, the temperature maintains fairly consistent 60°F (15.6°C), making it a comfortable work environment year round. Unfortunately, the relative humidity follows the prevailing weather conditions allowing a wide variation, especially between the winter and summer seasons. A study was undertaken to gauge the influence of relative humidity on shock wave generation, including the positive and negative phases of the wave.

Jan 1, 2011

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022

By Wallace R. Horn

"MR. CHAIRMAN AND GENTLEMEN :I begin this talk by making a couple of comments which are of the nature of disclaimers.Firstly, and as the Chairman has otherwise indicated, I was neither ""born into"" nor have I spent more than a few years of my professional life in the mining industry. I mention this because many might, and perhaps rightly, consider that an added qualification in presenting a report of what the industry has accomplished. Indeed, I am not here to blindly defend all of its actions and inactions in respect to environmental control over the years. Nor am I here to seek absolution of the industry's past transgressions - if indeed that is the word. Mistakes might be a better one. I concluded some time ago that the effects of those mistakes are too difficult to assess against the sea of errors of our total society. I should mention too that I am not an environmental engineer or specialist - only a portion of my interest is involved with this field. Perhaps this permits a perspective which allows a more accurate and objective view.One further comment here. My job today, as I understand it, is to generally report upon the nature and extent of the response of the metals mining industry to control of the environment. In the case of an industry operating at more than a hundred locations and for various reasons at various stages of progress, it is not an easy job. On the other hand, I wanted to avoid the use of generalities because, especially within the context of environmental or ecological opinion and of the practice of condemnation of industrial segments, I think we've had about enough of generalities until we know far more than we do.Finally, I am quite aware that a statement of future plans to achieve environmental control does not impress or satisfy as many people as it may have done some years ago. Public opinion demands to know what is currently underway, today."

Jan 1, 1972