Search Documents

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By See G. T

Bentonites and fuller's earths from seven localities in N.S.W. have been analysed with respect to occurrence, mineralogy and physical properties and areas for future prospecting have been indicated.INTRODUCTIONThe rapid expansion of Australian industry in the postwar years has been accompanied by an ever increasing demand for fuller's earth and bentonite, but in New South Wales at least the demand has been met principally by imports. However, some local and generally inferior active earths have been won to blend with imported materials to reduce costs. The important discovery of the widespread distribution of bentonite clays in the Northern Coal Measures, made recently by Grim (Booker, 1956), has givenimpetus to the further search for material comparable in quality to the imported active earths.Bentonite may be defined as a highly plastic clay, generally possessing swelling properties, composed essentially of montmorillonite and derived from the alteration of volcanic ash. Fuller's earth refers to any clay which, with or without chemical treatment, is capable of decolourizing mineral or vegetable oils and is, therefore of economic value. Montmorillonite is the active component of most fuller's earths, though palygorskite-, halloysite- and even kaolinite-rich clays have been used.Previous literature related to the New South Wales deposits has been confined to general descriptions and little technical data beyond an occasional chemical analysIs have been available. Bentonites and fuller's earths from seven...

Jan 1, 1959

By E. DeGolyer

The problem of good engineering practice and. of good conservation practice in oil production is that of keeping gas in solution. This can best be done by producing a field as a water-drive field. Some degree of water drive is believed to be present in most fields but in the past most fields have been produced too rapidly to allow water drive to be effective. Ultimate recovery should be So per cent greater for fields produced by water drive over that from gas-expansion fields. Wide spacing will permit fields of low-degree water drive to be produced effectively as water-drive fields. INTRODUCTION NEGLECTING all the complicated scientific and technical argument that leads to the conclusion, the solution of the problem of good production practice, of good engineering practice, and of good conservation practice in oil production is to keep gas in solution. This can best be done by producing fields at a rate low enough to make effective the water drive, which exists, it is generally believed, to a degree great enough to be made effective in more than 80 per cent of the fields of the United States. Oil is being so produced in the Ten Section field of California; the Hobbs field of New Mexico; the Yates, Hastings, Friendswood, Anahuac fields and the main sand of the Conroe pool, in Texas; the Magnolia pool in Arkansas, and doubtless in many other pools. The measures of success in the efforts to achieve the solution of the problem are the maintenance of bottom-hole pressure and the prevention of an increase in gas-oil ratio. Some decline from the original bottom-hole pressure and the production of some gas are essential. A pressure gradient from the reservoir to the well is necessary and at least as much gas must be produced as that in solution in a barrel of oil. Once the optimum pressure and the gas-oil ratio have been established, they should be maintained. How common is water drive in oil and gas pools? General opinion is that some degree of water drive is almost universal. Theoretically, this conclusion appears to be a sound one. According to our present understanding of the processes of sedimentation, we would expect to find all sands or sandstone charged with connate water unless it had been displaced by some other fluid, such as fresh water percolating into the beds at the outcrop, or oil and gas, or gas only, in reservoirs. The fact that the original pressure of the fluid system in most reservoirs is approximately that of the hydrostatic head of water for the corresponding depth indicates that the sands are charged with water, and common experience in drilling into the extensions of the porous zones beyond the reservoir is to find them watercharged. The very fact that oil and gas pools have substantial pressures in their original undisturbed state indicates either that a reservoir is a rigid, closed system, a con-

Jan 1, 1941

By H. L. Burmeister

This report describes the mining and milling practices used by the Eastern Magnesia Talc Co. at its Johnson, Vt., operation. The report also contains a description of the local geology and all available information on cost and performance data. Since 1925 the mine has produced continuously at an average annual rate of 54,000 tons, and the ratio of ore hoisted to finished product is roughly 2 to 1. Ore is stoped by a combination of shrinkage and sublevel methods. In any 24-hour period the mill produces an average total of 14 grades of finished talc product, 9 by dry grinding and air classification and 5 by wet grinding and flotation methods. The mine operates one shift per day, 5 days per week and the mill operates on a 3-shift, 5-1/2-day-per-week basis. Operating costs for 1958, on a percentage basis, were mining, 22.34; milling, 54.77; ore haulage, 2.89; and all other, 20.00 percent.

Jan 1, 1963

By TTE-Europe GmbH

A few years ago, the term Track & Trace for explosives was only known in Europe and Brazil at most; the introduction of this technology is experiencing an undreamt-of boom worldwide. More and more countries are enacting legislation to introduce Track & Trace of explosives and follow Europe and Brazil on this path. At present, the world's leading manufacturers are already using such solutions, are in the process of implementing them, or are in the planning process. However, based on the experience gained in Europe, there are outstanding challenges for all manufacturers. These are questions of compliance, logistics, distribution, and, of course, especially, the necessary adaptation of the production environment. However, this development involves considerable effort on the part of the manufacturers. New devices for marking the explosives and digitally recording the data are integrated into the production process. This should be done as cost-effectively as possible, without restricting production capacity and speed, and with as few process changes as possible. This paper uses real-life customer experiences examples to explain paths from project design to real implementation. Lessons learned from the experience of European explosives manufacturers are presented, missteps are described, and solutions are identified. Individual steps along this path are explained, and solutions are told to avoid pitfalls and bottlenecks. Finally, it refers to the risk analysis and concrete examples in implementing the planning into production. Methods of marking various explosives are shown, and the use of Track & Trace to solve logistics tasks in picking and shipping explosives, including the data exchange with ERP (Enterprise Resource Planning) systems.

Jan 26, 2026

By S. W. White

Plasma arc technology is increasingly being used to process a number of waste materials. In present research, plasma technology is being investigated to treat waste magnesium baghouse dust, which is a waste material from the Magnetherm process. This dust contains mostly MgO, but also contains NazO, CaO, and KzO. Plasma energy is to be used along with a reducing agent to produce pure gaseous magnesium while keeping the other materials in a slag. The magnesium will then be collected by rapid quenching. A non-transferred arc plasma torch is ideal for this reaction because of its high enthalpy and improved energy efficiency over conventional methods. Another advantage of plasma is that it allows for the pre-heating or pre-reacting of fine particles before contact with the melt. Thermodynamic calculations using the Gibb energy minimization method were used to determine the most stable compositions of the materials at various temperatures. Energy balances have also been calculated. These results conclude that we can recover approximately 98% of the magnesium with a proper quenching technique. The calculated results are compared with the experimental data, and good agreement between them was observed.

Jan 1, 1999

By Kyle Amoroso, Aaron K. McCain

Frozen soil shoring has been used for decades in the tunneling industry to provide temporary support of excavation for shafts and cross-passage excavations. However, horizontal penetrations through the frozen soil can prove to be challenging. The key to creating a stable portal through frozen ground is managing and mitigating groundwater flow into the excavation through the annular space surrounding the drill stem or casing. This paper will review different approaches that have been successfully used to penetrate frozen soil shoring on multiple projects.

Jun 13, 2023

By C. Birch

"A ‘geologically constrained’ orebody model has long been hailed as vital for a Mineral Resource statement that is compliant with the South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code). In this paper, the requirements for geological modelling as contained in the outline for the SAMREC Code are considered, and whether the new modelling software available on the market is a ‘black box’ or is better for modelling than traditional methods of wireframe creation.Implicit geological modelling is a technique that uses a radial basis function to establish and update geological models relatively quickly and efficiently from borehole data, outcrop data, manually interpreted vertical or horizontal sections, and structural data. Assays and any coded drill-hole data, such as lithology and alteration, can be interpolated.Leapfrog Geo software is an example of this new approach to geological modelling. A case study of a short training course in geological modelling for non-geologists at the University of Witwatersrand, as part of the Higher Certificate in Mineral Resource Management, is presented. The benefits of this type of geological modelling software are considered for this type of assignment as well as for mining industry applications.The use of geological models in mine planning is reviewed and a case study is presented comparing the variations in mine plan design and financial output of 13 final-year Mine Design projects from the University of the Witwatersrand School of Mining Engineering. These designs were all based on the same geological model created in the traditional way, and yet the resultant mine designs were significantly different, with very different resulting financial outlooks for the project. This raises questions as to how significant a very detailed model in the pre-feasibility and feasibility phases of projects really is, considering the huge costs involved in gathering the required data to build a SAMREC-compliant geological model."

Jan 1, 2014

By Jim F. Lemons

The Bureau of Mines Minerals Availability System collected and analyzed data for 34 nonlaterite and 9 nickeliferous laterite domestic chromite deposits in order to assess their viability as sources of chromium under present technologic and economic conditions. These 43 deposits, none currently in production, contain approximately 6.3 and 22.3 million metric tons of Cr203 at the demonstrated and identified resource levels, respectively. Approximately 4.6 and 15.6 million metric tons of Cr203 are recoverable at the demonstrated and identified levels, respectively, for the 34 nonlaterite deposits. None of these resources are economically recoverable at January 1981 market prices. Production of metallurgical-grade chromite (market price $128 to $144) would require a minimum chromite market price of $237 per metric ton. Chemical-grade chromite production (market price $74 to $85) would require a chromite market price in excess of $188 per metric ton. From the 34 nonlaterite deposits, roughly 5.4 and 17.6 million metric tons of ferrochrome could be produced at the demonstrated and identified resource levels, respectively; however, a minimum market price of $770 per metric ton of ferrochrome would be required to stimulate production. The nine nickeliferous laterite deposits were not evaluated through production stages because of uncertainties in process technology and cost.

Jan 1, 1982

By Frederick C. Hull

THE grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. USUAL METHODS of EVALUATING GRAIN SIZE A frequently used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.-The Metals Handbook1 has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.-Idealized grain-boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E19-39T. Standard Micrographs.- The Metals Handbook and ASTM Tentative Standard EI9-39T contain micrographs of hypoeutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diam¬eter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying grain size in ASTM Tentative Standard Es-39T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1947

By PAUL H. SHAEFF

THIS paper is presented with the idea of discussing only the basic open-hearth charge. The importance of the charging operation in producing steel is more clearly understood by dividing the principal components into four groups and discussing each separately, thereby becoming acquainted with what constitutes a charge. The significance of these components in the charge itself will then be taken up. Classification of the charge components is as follows: steel scrap; pig iron ; limestone ; refractories and coke. Steel Scarp The first component, steel scrap, according to size, analysis and cleanliness, may be classified as heavy, medium and light. Heavy melting scrap includes crop ends such as are produced in blooming ingots or the heavy crops from bar mills abovely in. in diameter; railroad scrap, which comprises rails, side-plates, car-frames, draw- bars, etc.; and such automobile forgings as axles, crank- shafts, gears, etc. This class of scrap should give a four-box charging-car (box dimension 24 by 18 by 72 in.) an average load of 10,000 to 20,000 lb.

Jan 1, 1926

In the March/April 2006 issue of the Journal, we published an ethical dilemma called “Blowing the Whistle.” We received many interesting responses to the article as requested. Some of the responses are printed here. We’ve also included “Blowing the Whistle” again in this issue as a refresher on page 37. Dear Editor, It is in my own personal belief that it would be extremely important if I were the blaster to take the following steps. 1. Hold an immediate emergency meeting with the contractor to convince them to stop work at this point.2. This meeting would need to be held with all powers that be in this construction company. This helps eliminate the hearsay (excluding the farmer). 3. Explain the entire situation to the contractors as it has been presented to the blaster by the farmer. 4. Recommend calling in an engineering or geological firm with the expertise to investigate this matter immediately, and take all immediate action based on findings. 5. Follow up with farmer allow him to speak, (a.k.a. vent) and assure him proper steps are being taken to come to resolve this matter. 6. Be a good listener, and communicator with the farmer while investigation is being conducted. 7. Should the contractor not want, or take any of these recommendations, the blaster himself and his company should question even working for this company ever again. This in itself would not be the class of people we would want to be associated with EVER.

Jan 1, 2007

By J Rose, D O’Toole, D Grant

Orepasses are a critical element in the transport of ore from the stope drawpoint to the surface ore stockpile, making them an integral part of an underground mine’s ore-handling system. Well-designed and operated orepasses improve productivity and lower operating costs over a long period of time.The Olympic Dam mine, as part of a 6 Mt/a expansion project in 1997, constructed a large network of orepasses feeding a rail haulage system to facilitate the movement of approximately 8 Mt/a to the Clark crusher and hoisting shaft. The orepass network comprises 14 orepasses and currently includes 59 individual tip points. The orepass network has been in operation for over 15 years and in excess of 110 Mt of ore has been moved through the system.Olympic Dam’s management of mine infrastructure includes a program of assessing the condition of the Clark system orepasses. A comprehensive program was initiated in 2011 and consisted of systemically performing volumetric surveys to determine the integrity of the various sections of the orepasses. The current geometrical state of the orepasses provides essential information for comparison of geotechnical and operational parameters and a baseline for understanding the key causes of orepass deterioration to assist in the planning of both usage and potential replacement options.The collection of geotechnical and operating data allowed the review of the current condition, potential longevity and associated risks with the various orepass sections. Initial studies have also reviewed options for rehabilitation and/or replacement.CITATION:Rose, J, Grant, D and O’Toole, D, 2016. Orepass monitoring and management at Olympic Dam Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 609–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By John Convey

This short paper deals with the subject of research and its relation to productivity. All who have stopped to even think about industrial re-search and its impact on the nation-al economy take for granted that research and development are pre-requisite to increased productivity. It is another matter, however, to identify and properly evaluate the many factors entering into the relationship between the two. Some studies are currently underway in the United States on the subject, but, so far, nothing much in the way of conclusive data has come to light. In Canada, we have not yet even produced any statistical figures on national productivity, although work is now being done on this subject and information will soon be available. The usefulness of being able to measure the benefits of investment in re-search and development in terms of industrial growth or productivity need not be laboured for the benefit of those interested in research management.

Jan 1, 1964

By W. van der Merwe

With the gold industry looking to process more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more crucial. This paper compares the two commonly employed "free" cyanide online analysis methods (amperometric and potentiometric end-point silver nitrate titration) with the common site laboratory rhodanine endpoint silver nitrate titration and ion selective electrode methods. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared with these measurements.

Jan 1, 2011

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By BUREAU OF MINES

This paper is a revision of Reports of Investigations , Serial 2541 , which was published in November , 1923 , for the benefit of State mining inspectors , safety engineers of mining companies , and others interested in electrical safety inspection in mines . It presents the important points that should be watched by inspectors and briefly reviews the work of the Bureau of Mines in testing of electrical apparatus and equipment to determine their permissibility for use in gassy coal mines .

Jan 1, 1929

By H. Leitch

In laboratory experiments, the Bureau of Mines investigated melting, quenching, and sulfuric acid leaching of alumina from mixtures of albite and anorthite, and from anorthosites containing 26 to 32 percent alumina. Variations in pouring temperature, quenching and leaching conditions, were studied with respect to the extraction of alumina and impurities. Virtually all of the alumina was dissolved by leaching melted and quenched California anorthosite in boiling 16-percent sulfuric acid solutions for 15 to 30 minutes. The leach solutions were readily separable from the solid residue by conventional thickening and filtration techniques. Only 2 to 5 grams of SiO2, Fe2O3, or CaO dissolved per 100 grams of alumina. The quantity of SiOz in solution varied inversely with the duration of the leach and with the concentration of the H2SO4 solution used. Melted and quenched Wyoming and Minnesota anorthosites with SiO2:CaO weight ratios of 4.3 and 3.2, respectively, were less amenable to sulfuric acid leaching than California anorthosite with an SiO2:CaO weight ratio of 5.3. However, excellent results were obtained on the Wyoming and Minnesota anorthosites by the addition of SiO2 to these materials before melting, in quantities sufficient to adjust the SiO2:CaO weight ratios of the furnace charges to between 4 and 6.

Jan 1, 1966

By James Westfield

A brief résumé follows of some of the most recent activities of the Division of Coal-Mine Inspection that have had a favorable effect. on health, safety, and injuries at coal mines: 1. There were approximately 8,510 active coal mines in the United States during 1955. In all, 82,389 regular Federal inspections of coal mines have been made since Public Law 49 became effective in May 1941; 9,823 of these inspections were made during 1955. 2. The Bureau of Mines introduced the revised Coal-Mine Accident-Prevention Course for Supervisors in the coal-mining industry on March 1, 1948. Since that date, 19,455 supervisors and those aspiring to official positions have completed such training conducted by personnel of the Division of Coal-Mine Inspection.

Jan 1, 1956

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada's Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988