Search Documents

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side of the continuous miner; 100 percent of the discharge redirected back toward the face, but divided equally to both sides of the machine; and 15 percent of the discharge redirected toward the face on the off-curtain side of the machine, with 85 percent directed into the return. These models were compared against a model with a conventional scrubber discharge, where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100 percent redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner, which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.

Jan 1, 2015

Electronic noses are being used in the processing industries and in fields such as environmental and occupational hygiene to detect a wide variety of problems from contaminated foods to toxic chemicals in soils. Recently, research has been conducted into the use of these devices for detecting spontaneous combustion in mines with the aim of producing a method for early detection of a developing heating. Gas samples were collected from both SimtarsÆ 16 m3 large-scale spontaneous combustion reactor and the University of QueenslandÆs two-metre column. The samples were analysed using an electronic nose. GCMS and HPLC were used to identify some of the components present. A number of issues both from a practical mine situation and a scientific standpoint have been identified that need to be addressed before these devices can be used to detect a developing heating. Aluminised bags routinely used in the mining industry to collect gas samples for analysis of the permanent gases are not suitable for use with electronic nose devices as they have a æfingerprintÆ from the polymer lining that interferes with the coal heating fingerprint. Tedlar bags used for environmental gas sampling are also unsuitable due to their fingerprint. Gas samples can be collected in glass gas bulbs with aluminium seals and successfully analysed. However the aluminium foil used to seal the bulbs is a restricted item in underground mines. It was also found that the volatile organic fingerprint of the coal heating was extremely weak at temperatures below 130¦C. Before a useful application can be developed, further investigation into the chemical species present in the off-gases from Australian coals is required.

Jan 1, 2005

By K. C. Sole, M. Makonese

Bushveld Belco is commissioning a plant for production of electrolyte used in vanadium redox flow batteries. Owing to the source material, the electrolyte is contaminated with Fe, at concentrations up to 140 mg/L, which negatively affects battery performance. This study examined the use of ion exchange to reduce the Fe concentration to the target value of < 100 mg/L from a feed solution containing 100 g/L V in 4 M H2SO4. Four resins with possible application were identified: Puromet MTS9570, Puromet MTX7010, Puromet MTS9500, and Puromet MTC1600H. Puromet MTS9570 outperformed the other three resins in all batch experiments with respect to loading capacity and selectivity over V, and was evaluated for Fe removal in fixed-bed column loading tests. Based on these data, preliminary sizing and design of a full-scale column was undertaken. Owing to the difficulty of eluting this resin, a philosophy of discarding the resin on loading to full capacity was considered. These data revealed that, despite the high selectivity of this resin for Fe over V, it would be too expensive and impractical to use this resin for full-scale operation under such conditions. It is recommended to remove iron earlier in the flowsheet prior to generation of the 4 M H2SO4 electrolyte.

Dec 11, 2024

By Jamal Rostami

Continuous miners (CM) are the most popular underground mining machinery in soft rock mining, playing a dominant role in the production of minerals ranging from coal to evaporites while finding increasing use in salt and potash mines. Along with the ongoing technological advancements in the mining industry and the underground equipment, new generation of CMs offer several new features that are designed to enhance their operational capabilities and production rate. In addition to new bits and bit holders, one of the areas of improvement is the cutterhead design through computer modeling and simulation based on the full scale cutting tests. This paper discusses the state-of the-art CM technology and development of the computer models for design analysis and performance estimation of CMs. The general approach used in the modeling, along with the results of field trials for several projects will be presented.

Jan 1, 1998

By A. Sand

Within stamp-charged coke making a large volume of coal is compacted to one single coal cake before entering the coke oven chamber. This is done by means of several falling stampers in a stamping machine having a mold nearly of the oven?s dimensions. Producing a high quality coke also from inferior coals requires a cake density of approximately 80% of the coal density. Besides that the industrial stamp-charging process demands a minimum mechanical strength of the coal cake to move it from the stamping mold into the oven chamber without failure. Densification and the build-up of cake strength were investigated earlier in stamping tests using a micro-stamping device. The quantities derived from these tests (as e.g. cake density or porosity) represent average values for the entire cake. Statements describing the local compaction state at different heights are difficult to achieve without destructing the cake. In order to gain better insight into the densification process and the inner structure of the coal cake a computational model based on the discrete element method (DEM) has been set up using 2 and also 3-dimensional simulation software. The stamper?s position and velocity as well as the force acting on the stamper were monitored and the model?s response was compared against measurement data from laboratory stamping tests. It was possible to reproduce the force and displacement pattern of the stamper in response to the viscoelastic properties of the cake using standard DEM bonding and contact models. Furthermore, the rearrangement of particles in response to the compaction by the stamper was tracked by calculating their displacement at the point the stamper hit the coal surface. The latter can also be used as indicators of particle deformation or breakage. By defining control points at different heights the particle displacement, stress and strain rates, porosity could be studied at different heights. Keywords: coke making, coal stamping, compaction, agglomeration, DEM, simulation

Sep 1, 2012

By Karl Berger, Roman Schneeweis, Dietrich Mathweis

With increasing demands from customers to provide flat strip with tighter tolerances on material properties, particularly flatness of e.g. martensitic steel grades (M1500), it has become necessary to develop strategies to improve flatness without influencing the tensile properties for such hard steel grades. Usual skin pass mills are not capable to apply sufficient tension and roll force for these kinds of material to improve the flatness. Therefore, alternatives had to be searched for. This paper describes skin pass - / temper – rolling methods from the classical one to new alternatives in order to satisfy the demanding market of higher material properties and idle running mills in rolling plants.

Oct 1, 2019

By A Grace, C Sennersten, A Davie, R Lyu, C A. Lindley, O Goldstein, T Thomas, L De Macedo Camargo

Block modelling is a well-established method for modelling ore reserves as a basis for strategic mine planning and mine development. Off-Earth mining, particularly of asteroids, can benefit from block models; however, the significantly different characteristics of asteroids and their methods of mining require reconsideration of the geometry and annotations of block models. Terrestrial block models consist of rectangular prisms within Euclidean coordinate systems. Their labels and parameters typically include location within a mine-specific coordinate system, x, y and z dimensions, specific gravity, hardness, grades of metals of interest and so on.These data provide an input to mine design and strategic mine planning. Mining asteroids may require different coordinate systems (eg spherical, elliptical or cylindrical, rather that Euclidean) and attributes that vary from Earth-based block models. These include: variable gravitational vectors throughout the block modelrotational moment or accelerationrotation rates. Materials within asteroids may show different isotopic compositions. Asteroid mining has the unique characteristic of a mine being identical with an asteroid. The position of the asteroid/mine in space and its full orbital elements provide critical inputs to mission design and costing. Hence, the block model concept needs to be extended with this metadata. The orbital position and behaviour of the Earth must be included for active mine planning, and increasing automation of mine planning and operations needs to consider terrestrial weather and telecommunications infrastructure. Financial planning requires analysis of the net present value of extraterrestrial mining compared with terrestrial alternatives, so a fully automated mining enterprise should integrate terrestrial and extraterrestrial block models at different scales and resolutions. Blocks can be indexed via octrees, allowing for hierarchical scales that support analytics for deriving new knowledge and correlating features across different scales.CITATION:Lindley, C A, Sennersten, C, Davie, A, Goldstein, O, Lyu, R, Grace, A, Evans, B, Pentecost, D, Thomas, T, De Macedo Camargo, L, Craig, J, Salomao, G N, Hellicar, A, Biggins, D, Timms, G, Coombe, M, Shahriar, M S, Smith, G and Rahman, A, 2015. A multilayer 3D index tool for recursive block models supporting terrestrial and extraterrestrial mine planning, in Proceedings Third International Future Mining Conference, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By C. M. Brinckerhoff

Much has been written in the mining technical magazines about the caving system. Many of these articles were published in the Transactions of the American Institute of Mining Engineers prior to World War II. In recent years little has been written on mining methods or on the detailed planning always required. Block caving had primarily been used to mine deep copper ores in Africa, the United States and in Chile, although other ores had been mined by this same system. Asbestos ore had been caved in Canada, tin ore in Bolivia, molybdenum ore in Colorado, iron ore in Wyoming and Sweden, and limestone in California.

Jan 1, 1984

By A. J. Hargraves

"It is difficult to quantify comparatively the gassiness of a property. The most common index to gassiness, cubic feet of gas per ton of coal mined, is very arbitrary and does not take into account the geological setting nor the mining operation. The gassiness of a virgin coal in situ can be assessed, but no method is precise and the most accurate methods involve prolonged field and laboratory experiments. In general, gassiness increases with depth. Whereas 'gas' normally implies methane, other gases such as nitrogen, carbon dioxide, etc. may be present in seam gas also. The inflammability of methane is a problem, particularly the explosibility of a methane-air mixture; also oxygen dilution is involved in high gas concentrations and some gases are poisonous even in low concentrations. Cross measuring into a virgin seam is usually not as troublesome as development in the seam, where narrow openings may require strong ventilation to dilute gases exuding from the face and sides. Total extraction presents problems of gas from the working seam, or from adjacent seams, particularly at the return side, or of gas-laden air from the goaf streaming out or sometimes surging out intermittently, again on the return side. In pillar extraction or longwall retreating special roadways may be required to allow the side-to-side and end-to-end flushing of the goaf which is somewhat inherent in longwall advancing. Layering may occur, particularly where ventilation conditions are not brisk. Outbursts of gas from adjoining seams may be induced by sudden rupture of roof or floor in caving workings. Outbursts of coal and gas from the working seam may occur, mostly in development work, under special environmental circumstances. Gas problems may be reduced or eliminated by predrainage of gas ....:. rarely successful from the working seam - usually undertaken from adjoining seams prior to escape of gas released by caving. The ideal solution - general predrainage of gas to the surface from measures prior to mining - has yet to be accomplished. • In the planning of gassy mines it is possible to make an assessment of gas contained in the seams and to estimate what proportion will be released into the mine air, but emission of gas into mine workings is never steady and at present there is no better planning criterion than experience at the mine next door!"

Jan 1, 1973

By J. Boisvert, E. Daniels, C. Deutsch

"INTRODUCTION Conventional mine planning is performed on a single resource model at a selective mining unit (SMU) scale deemed appropriate for the deposit and mining method. Estimation methods such as kriging and inverse distance, commonly used to construct a single model, are susceptible to histogram smoothing (Rossi & Deutsch, 2014). This can be mitigated by limiting the number of composites per estimate, therefore correctly reproducing the distribution of estimates (Boisvert & Deutsch, 2012). Search limiting techniques remedy histogram smoothing at the cost of introducing a problematic conditional bias (Isaaks, 1999) and introduces even greater spatial smoothing. Localization is an alternative, offering histogram reproduction through post processing of more robust probabilistic modeling techniques. A single localized model at the SMU scale is desirable. The correct histogram can be reproduced and a single model allows for the use of conventional mine planning and resource evaluation techniques. Despite the advertized benefits of localization, the necessary reliance on a larger panel scale as a middle step in the localization process yields unsightly “edge-effect” artifacts (Boisvert & Deutsch, 2012). Two approaches to artifact reduction are presented here. The first is a straight forward optimization approach designed to minimize an objective function that penalizes artifacts including panel edge discontinuities to generate a model free of panel edge-effects. The second approach redefines a panel in a less conventional fashion as a randomly chosen set of SMUs throughout the domain. This method produces a model void of any regular panel shape resulting in an artifact free model. Artifact reduction minimizes the obvious “edge-effect” issues of localization but local precision issues described by Boisvert & Deutsch (2012) persist. Localization is not a replacement for quantified uncertainty for comprehensive risk analysis and resource evaluation. LOCALIZATION Initially developed with Uniform Conditioning in mind, localization collapses a distribution of local uncertainty at a panel scale to an SMU scale model for mine planning (Abzalov, 2006). This process has been extended to Indicator Kriging (Hardke, 2011), Sequential Gaussian Simulation (Boisvert & Deutsch, 2012) and MultiGaussian Kriging (Daniels and Deutsch, 2014). The localization process is performed in a similar fashion regardless of which technique is chosen to create the prior model of uncertainty. Methodology There are three scales of importance considered in the localization process. The point scale, otherwise known as the data scale, is the smallest and is the scale at which experimental data is collected. The SMU or block scale is the familiar scale at which mine planning and resource evaluation takes place. Lastly, the panel scale is larger and contains a number of SMUs. Each of the three scales is illustrated in Figure 1."

Jan 1, 2015

By Z. Naziemiec

Since several years in Poland a huge demands on mineral aggregates occur, for the reason of intensive development of housing and road industry, as well as industrial building. Limitations in re-sources of broken aggregates in Central and Northern parts of Poland cause, that both the non-waste production of aggregates with high quality and the production of alternative aggregates from recycling gain greater importance, nowadays. It entails increase in demands for crushing devices, which are easy and reliable in operating as well as inexpensive and enabling to obtain a good quality products. Jaw crusher, regarded as the most spread in Polish industry, meet these requirements, however, their crucial disadvantage is a large content of irregular grains in crushing products. Numerous investigations show, that the shape of grains is a significant feature of aggregates, which influences on durability and quality of produced concretes. The advantage of jaw crushers is their easy operation, low price as well as low amount of dusts (wastes) generated in comminution products in comparison to other types of crushers (i.e. hammer crushers).

Jan 1, 2014

"10.1. IntroductionAs discussed by Westland (1981), the six platinum-group elements (PGE) belong to the Group VIII transition metals, to which iron, nickel and cobalt also belong. The chemical similarity between these nine metals accounts for the fact that they tend to be concentrated together as a result of geological processes. These processes started to effect the distribution of these metals at the very beginning of the earth's history.The first line in Table 1 gives the concentration of nickel and certain other Group VIII transition metals in carbonaceous chondrites, those meteorites with a composition that is believed to reflect best the composition of our planetary system apart from hydrogen and helium. The second line is the estimated concentration of the same elements in the earth as a whole. It is seen that these two estimates are quite similar, the earth being perhaps 2 to 3 times richer in these particular metals than the planetary system as a whole. The reason for this is not fully understood, but it may be due to the earth being formed by the accumulation and capture of a greater proportion of iron (and therefore siderophile-rich) than stoney (and therefore siderophile-poor) planetesimals than the planetary system itself.The third line in Table 1 is the average composition of the crust of the earth. With the exception of iron, all of the Group VIII transition elements are rare in the crust, present at concentrations of It tOO to Itt ,000 of that of the bulk earth. This is because the outstanding chemical characteristic of this group of elements is their siderophile nature; that is, their tendency to alloy with metallic iron. Because of this, once the earth became molten very early in its life history, these elements dissolved in the molten iron present at this stage and were removed from the outer accessible parts as this dense liquid sank to the centre of the earth to form the core. Although iron was the main instrument of concentration of the Group VIII metals, its much greater over-all abundance and its ability to combine with oxygen more easily than the others in the group means that significant amounts still remain in the oxidized portions of the earth.The fact that most of the Group VIII metals are available to use in workable concentrations at all is that they are 5 to 30 times more concentrated in the earth's mantle than the crust, as shown in line 4 of Table I. There has been a constant, if slow, interchange of matter between the mantle and the overlying crust throughout most of the earth's history and, under certain circumstances, this interchange has given rise to economic concentrations of metals."

Jan 1, 1979

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

By Malte J. M. Gurgel, Axel Preusse

Recent three-dimensional surveying techniques have opened up new opportunities for the registration and monitoring of underground cavities. There are essentially two main methods available: Laser scanning, which is used both above surface and increasingly underground, and photogrammetry, which is also experiencing a renaissance with techniques like structure from motion through the algorithm-based orientation of high-resolution images. Both methods provide the capability to reconstruct reality by various 3-D products like points clouds and meshed models. However, they differ significantly in the steps of registration and calculation as well as in the resulting evaluation options.

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By Robert L. Goehring, Fred Munene

This case history for three major additions to a tire manufacturing plant in north Georgia discusses the impact of highly variable Karst (sinkhole) geology on both foundation design and construction. For Phase 3, alternatives were considered for a heavily loaded mixing tower with up to 2,000 kip column loads. A non-traditional approach of using auger cast piles was adopted. To satisfy a risk-averse Owner, a pile load testing program including strain gauges was conducted. One test pile was cored full depth to demonstrate effective bearing on steeply inclined rock. For Phase 4, similar methodology was used at another critical mixing tower structure associated with that phase and the installation procedure was refined to reduce grout take. In Phase 5 construction, another mixing tower and the equipment pits were supported on auger cast piles. After pile installation, a sinkhole opened up between two equipment pits. Remedial grouting was performed. Development also required construction of a R&D building over a 96 inch diameter RCP storm sewer. Auger cast piles were used to support the building to avoid overstressing the existing pipe and risk separating joints. This case history outlines lessons learned while constructing auger cast piles in Karst and proving quality was built into the foundations.

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By Jacob L. Brinkman, Catherine E. Johnson

Researchers are exploring the use of unmanned aerial vehicles (UAV) to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect density-based concentrations as measured by some governing entities, including the Occupational Safety and Health Administration (OSHA). 

By W Mahoney, F Clement, E Saraiva

Prefabricated waterproofing sheet membranes are extremely complicated to install in underground sections with complex geometries and, despite being already subjected to quality tests in the factory, the installed membrane often exhibits leakages due to different reasons. Main sources of leaks are the required high amount of welding seams and damages caused during installation of reinforcement, as well as overstretching and poorly installed secondary concrete linings. Also the design of the tunnel lining is strongly influenced and limited by the use of prefabricated waterproofing sheet membranes. The use of sprayed waterproofing membranes for more than a decade has contributed to durability and serviceability, as well as to increasing sustainability of tunnel linings. The presented sprayed waterproofing membrane MasterSeal 345 is an advantageous alternative to prefabricated waterproofing sheet membranes under typical tunnelling conditions, especially in geometrically complex areas, such as in lay-by niches, cross passages and crossover caverns, where installation of conventional waterproofing membranes is inherently difficult, and locating leaks is challenging. This membrane has been successfully used in underground projects with different waterproofing design concepts and under diverse hydro-geological and environmental conditions for over a decade. It provides tunnel designers with different options and optimisation for the design of the tunnel concrete lining. Additional advantages to owners, contractors and designers from the use of the sprayed membrane include flexibility in the design, increased productivity and flexibility in working programming, as well as improved logistics, resulting in significant program and cost savings and reduced long-term maintenance costs. This paper describes the key features of this sprayed waterproofing membrane, its application range and limitations, the waterproofing concept, design options and related benefits. Further, guidance for membrane application and quality control and a summary of two recent project references in the United Kingdom and in Switzerland are provided.CITATION:Saraiva, E, Clement, F and Mahoney, W, 2014. The use of sprayable waterproofing membranes in underground structures – concept, design options, benefits and limitations, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Dennis, T Hunter, R Coleman

For metallurgical plant design, it is necessary to progress through successive phases of test work, piloting and process development before involving all the other engineering disciplines and “freezing” the process design criteria and flow sheet. This process usually relies upon the experience, skills and personal preferences of various technology providers, study and engineering entities, test work and metallurgical laboratories and, most importantly, the owner’s team and its operators. Current industry trends include lower grades, more complex orebodies, geometallurgy in defining orebody variation and design envelopes, more common “hybrid” plant processes and the market demands for more reliable, timely and predictable early plant performance.This paper will discuss interaction of these trends and provide guidelines for the level of detail and technical complexity required for a number of different “typical” examples. The paper will pay particular attention to the study definition level translated into the required detail and certainty needed by the overall process “owner” and original equipment manufacturer (OEM) equipment suppliers to ensure the best real plant performance. Some recent case studies will be discussed. In many projects, at a late stage of project definition, it has become common practice to undertake a “value engineering” phase. Although it could be argued that this should be undertaken earlier, it is largely driven by an overall need to reduce capex and “optimise” the perceived “fat” built into the project during the detailed design process. This value engineering can be very counterproductive to project timing and operational performance and warrants discussion.The paper is intended to promote discussion on a topic of wide interest. The authors’ diverse backgrounds and experiences are integral to the views in this paper.CITATION:Dennis, A, Coleman, R and Hunter, T, 2017. Critical process design considerations from test work to operations, in Proceedings MetPlant 2017, pp 12–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017