Search Documents

By Mackenzie Burnett

An inducer-type pump, capable of injecting dry coal into a hydraulic transport pipeline has been developed and installed in a specially designed and fabricated slurry injector vehicle. The full scale prototype injector system can deliver up to 11 ton/min of coal into an 8-in pipeline t pressures up to 95 lb/in2. The Helical Inducer Injector operates on centrifugal principles with flow passing axially through helical pitched conical rotor. Water is delivered to the pump through an annular slot at the atmospheric pressure coal inlet. The spinning rotor maintains an air-core vortex of water which pressurizes the discharge housing. A screw feeds coal through the open inlet into this vortex. The inner radius of the vortex contracts as pressure is increased, giving a limiting maximum pressure which is proportional to the square of the rotor speed. Below this limit, flow rate, discharge pressure, und rotor speed re independent variables. The self-powered, 4 -in high slurry injector vehicle follows and receives ROM coal from a continuous miner, reduces the top size to 3-in, and delivers the sized coal to the injector feed screw for slurry formation and pumps it through a mobile hose attached to the vehicle's outby end.

Jan 1, 1983

By E. A. C. Chamberlain

New techniques for the continuous sampling and analysis of mine air are expected to replace traditional methods used for the early detection of spontaneous combustion. It has been established that the rate of evolution of carbon monoxide is the earliest indicator of incipient spontaneous combustion. Two methods of continuous monitoring of this gas are available and are now in use in the UK collieries. The first is the UNOR infra-red gas analyser, which is flameproof and may be used underground; the second is a system of tube bundles, which permits air to be drawn from any critical point in a colliery and analysed on the surface. Each system has its advantages and disadvantages but both provide the colliery manager with far more information on the condition of his pit than could previously be obtained by spot sampling and laboratory analysis. This paper describes the two systems presently in use and assesses likely future developments.

May 23, 1905

By X Hu, Z Pokrajcic, R Embry, P C. Stewart, J Carpenter, E Jones

Whilst the value of Pit to Plant and Mine to Mill optimisation has been proven since the 1990s, sustaining the productivity and efficiency gains typically requires ongoing test work, blast trials, plant surveys, and model calibration services. In contrast, the input to digital twin Pit to Plant or Mine to Mill optimisation is tens to hundreds of millions of tonnes of standard mine operating data. This paper presents a series of digital twin case studies from across the mine value chain, including machine learning testing methodology, model accuracy statistics and the application of Shapley Additive Explanations (SHAP) for model interpretation. These case studies demonstrate how machine learning and data fusion ore tracking connects hundreds of millions of tonnes of downstream performance data to produce digital twin models (operating models that are continuously updated and integrated into the wider Mine to Mill/Pit to Plant ore tracking system). Digital twin modelling software has been used to add block model variables for dig-rate, crusher and mill throughput, recovery (tailings grade), lump yield, product grade and product quality, fines yield and fines in lump. Block-by-block predictions are added to the geological resource and grade control block models as new block model variables. These new block model variables are used across all mine planning time horizons from life-of-mine planning to daily schedules. In addition to the materials handling and geometallurgical prediction case studies, the paper also presents digital twin case studies for drill and blast simulation and plant set point optimisation. The case studies show how digital twin simulation enables drill and blast engineers to simulate the effect of different blast designs in different blast domains using the mines operating data. Plant set point optimisation applies mathematical optimisation algorithms to the machine learning model to provide live operational decision support to metallurgists and plant operators. The digital twin machine learning case studies demonstrate a digital and sustainable paradigm for Mine to Mill and Pit to Plant optimisation.

Jun 22, 2022

By Niloy K. Nath

Two layer sintering by charging green sinter mix with normal coke rate in the upper layer and reduced coke rate in the lower layer, can substantially reduce the coke rate and also improve the sinter quality by producing more uniform thermal profile through out the bed height. The two-layer sintering process have been analyzed by numerical simulation of the process by a detailed CFD based model, considering all the important phenomena like gas-solid reaction, melting and solidification, flow through porous bed, heat and mass transfer etc. Optimization techniques like genetic algorithm, differential evolution is then applied to evaluate the optimum coke rate in the two layers of the bed to produce the ideal thermal profile and melting fraction in the sinter bed for optimum sinter quality. Through this optimization method both high quality sinter with minimum return fines can be achieved along with reduced coke rate. Application of a genetic algorithm for this type of process optimization has several advantages over the traditional optimization techniques since it can identify global optimum condition and perform multi-objective optimization much easily for complex industrial process like iron ore sintering. Keywords: Two-layer Sintering, Iron Ore Sinter Quality, Ergun's Equation, Gas-solid reaction, Melting Fraction, Multi Objective Optimization, Pareto Set, Genetic Algorithm

Jan 1, 2003

By Jens P. Nielsen, W. H. Justice

This paper describes an improved acidizing technique which has been applied in acidizing gas wells in the La Gloria Field. Wells acidized in this manner exhibited a much greater increase in deliverahility than wells acidized in the conventional manner. The acid is injected into the well in small slugs separated by a small volume of high pressure gas. The acid and gas are displaced from the tuhing by high pressure gas to reduce the hydrostatic head on the well when the acid is recovered from the well. The well is opened for production as soon as the acid and gas are displaced. This procedure permits a very rapid recovery of the acid which results in large increases in the deliverability of the gas wells. It has been found advantageous in the acidization of gas injection wells to inject the high pressure gas directly after the acid without backflowing the acid out of the well. This practice has made it possible to inject the gas in the injection wells of this field with a much lower pressure differential. This reduces the horsepower required to inject the gas and also decrease:, the number of injection wells required per reservoir. INTRODUCTION The results obtained by acidizing gas wells ill the La Gloria Field have varied considerably in the past. For this reason. a planned study of the acidizing procedure was undertaken in order to obtain more consistent results. The Frio Sands of the La Gloria Field are rather permeable and it was not necessary to acidize many of the wells when they were originally completed. At the completion of an eight-year cycling program in several of the gas reservoirs, it became necessary to recomplete many wells in other reservoirs. It was found that the opan Flow potential of the wells recompleted in different sands was not as large as wells that were originally completted in that reservoir. A study of the drilling records of several of these wells indicated that the sands had originally been subjected to considerable hydrostatic drilling fluid overload while the well was being drilled to the deeper sands of the field. It is indicated that during this eight-year period, the drilling mud and water that were lost into the formation when the well was being drilled had formed a relatively impermeable Eone around the well bore. This impermeable zone around the well bore made it very difficult to obtain high deliverability wells when the original wells are recompleted in other zones. Muskat' has shown that in uniformly permeable and porous formations a zone of partial plugging one ft in radius around the well would drastically decrease the productivity of the well. The analysis for this problem shows that the production capacity of a well is very sensitive to the value of the permeability of the zone immediately surrounding the well bore. This is to be expected in view of the highly localized character of the pressure drop in a radial flow system about the well center. The reduction of the deliverability is not proportional to the thickness of the mud-affected zone as the major portion of the reduction in deliverahility IS caused hy the

Jan 1, 1952

By T. B. Jarboe, H. Wen

Introduction The 150 MW circulating fluidized bed (CFB) power plant described in this article is the product of recent Bechtel experience in the industrial power and steam market, where the economic feasibility of fluidized bed projects has been proven. The ability of CFB boilers to burn low grade fuels makes it possible to burn low ranking coals or coal wastes. These include anthracite culm, coal mine rejects, and coal wash-plant-waste slurries. This article also addresses the impact of fuel characteristics on plant design. This includes solids handling, steam generation, sulfur capture, and auxiliary load requirements. The uncertain economic environment in which utilities must now operate has shifted the industry's interest away from large, base-loaded generating units to small, more versatile installations. Utilities now consider purchasing new generating capacity in smaller increments and staging its deployment to correspond with demand increases. In this way, they lower their risk in the increasingly hazardous art of long-range load forecasting. This strategy has many advantages. Multiple, smaller units have inherently greater turndown capability and better availability than a single larger unit of the same size. In addition, the smaller units will each have better cycling capability. And, with CFB combustion, the smaller units will have greater fuel flexibility. General plant description The 150 MW powerplant described here is a grassroots CFB unit. Fluidized bed technology differs from conventional combustion techniques. With CFB, solid fuel, together with inert material such as sand, gypsum, limestone, or ash from the fuel, is kept suspended in the combustion chamber. This is done by using the action of the fluidizing air distributed below the bed. Fluidization promotes the turbulent mixing conditions required for good combustion. The turbulence causes the entire mass of solids to behave like a liquid. The result is improved mixing. This allows heat to be generated at a lower and more uniformly distributed temperature that is below the ash fusion temperature of most coals. The fluidizing mechanism offers several other advantages over conventional combustion. There is less volatilization of alkali compounds, which cause deposits on boiler tube surfaces. And there is less sensitivity to the quantity and nature of the ash in the fuel. The low combustion temperatures prevent vitrification of the ash particles and minimize problems associated with furnace slagging. The ability to select from many fuels is one of the major advantages of CFB combustor technology. Fuels that can be burned in CFB plants to produce steam and electricity include: low grade coals with high ash or sulfur, lignite, peat, wood and pulp products, biomass, refuse, anthracite culm, petroleum coke, and oil shales. The plant's turbine cycle uses superheated steam at 12.4 MPa (1800 psi) and 538°C (1000°F), with single reheat to 538°C (1000°F). Two high pressure and three low pressure, closed, feedwater heaters are furnished. So is a deaerator, which is an open, direct-contact heater. The CFB plant exceeds EPA's New Source Performance Standards (NSPS) for air emissions. The design limits sulfur dioxide (SO,) emissions to 0.25 kg/GJ (0.6 lb per million Btu). SO2 reduction occurs in the combustor by reac-

Jan 11, 1988

By L. R. Hougen

The Falconbridge Matte Leach Process yields high-purity nickel chloride by selectively dissolving nickel from copper-nickel converter matte with hydrochloric acid , purifying the solution by solvent extraction and crystallizing NiCl2 4H2O by further acidifying the purified leach liquor. In the Kristiansand Matte Leach Plant, a granular oxide is produced by high-temperature hydrolysis of the nickel chloride for subsequent reduction to a high-purity granular metal product, designated NICKEL 98. This paper describes the investigation of on alternate route to processing nickel chloride in which high-quality cathode nickel is produced by electrowinning from all- chloride electrolyte. The investigation was made in a pilot circuit containing two production-size electrowinning tanks operated in conjunction with the commercial-scale leach plant.

Jan 1, 1977

By F. Calizaya, S. Bhattacharyya

"INTRODUCTION Mechanized underground mines often suffer from noise overexposure. Noise levels are usually above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach 121 dB(A), especially when fans are not equipped with silencers. Use of silencers seldom ensure PEL for various reasons. Overexposure of noise induces permanent hearing loss among mine workers. Recent field studies by a NIOSH-funded research project at six coal and non-coal mines revalidated the findings. The University of Utah has undertaken laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material has been designed and tested. The silencer and an associated extension which can be repacked with different dampening materials were used in various configurations. Attempts were made to simulate field conditions where installations are quick and not perfect. The test results are presented here. NOISE IN UNDERGROUND MINES Noise induced hearing loss (NIHL) is a chronic problem in the mining industry. In spite of regulations being in place and elaborate hearing protection programs under way, hearing loss is prevalent among the mine workers (Bise, 2001). All production and support machinery in mining generate loud noise often beyond the approved exposure level. Researchers in the U.S. have identified auxiliary fans as one of the major sources of noise that can create noise exposure levels up to 121 dB(A), which is one of the highest in the mining operation (Bauer, 2006). Studies have demonstrated substantial reduction of noise level by using silencers. Adequate fan selection and proper utilization of silencers in auxiliary fans have great potential of abating the problem. In hard rock mines, auxiliary fans are used in blower configuration to ventilate development headings and large production stopes, and also to ventilate underground shops, crushers, conveyor transfer points, etc. Typical duct diameters in hard rock mines vary from 0.91 m to 1.21 m. Silencers are often omitted for cost reduction. In coal mines auxiliary fans are used in exhaust configuration with rigid ducts 0.61- 0.76 m in diameter (Hagood, 1982 and Moreby, 2009) to ventilate working faces in gate-roads and main entry developments. Sometimes, stone dusters are added at the discharge end to dust the roof, ribs and floor. AUXILIARY FANS AND SILENCERS Auxiliary fans are relatively smaller in size than the main fans and often have high rotational speeds (1800 -3000 rpm). Fans are selected based on pressure-quantity requirements and space restrictions only. Noise emissions are rarely considered during the selection stage. Installation of fans, ducts and other accessories is mainly based on best practices, which often do not include noise control. As a result, the operation of an auxiliary or local ventilation system normally produces excessive noise."

Jan 1, 2018

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By M. C. Mound, L. Fradette, C. Colbert

Metallurgical Accounting in the mineral processing industry transforms accumulated process data, including flow rates and assays, into a coherent information format. This is used to rapidly provide production reporting and key performance indications. A fully comprehensive and coherency of available data must be a component of any system expected to accomplish reconciliation in the mass balancing process. Quality issues are thus improved with such desired methods via a mass-balancing engine utilizing the results of measurements acquired by various on-line sensors, analyzers, and sophisticated laboratory equipment. Metallurgical Accounting, when accomplished through such an engine, provides high value information in a simple, straightforward, and simplified manner. Exceptional utility is then transparently available to authorized personnel for access to metallurgical accounting reports, production reports, mass balance results, performance indicators, and so on. This paper discusses how such information can be used to "drilldown" into each result set by consulting the data hierarchy to evaluate and validate calculations and input data used to produce the specific results being queried. The power of such a system resides in the full and true integration of all production and laboratory data. What is integrated are the data thus acquired via a single user interface, a single database, a single configuration tool, etc. From this comes the derivation of contextual information and its maintenance. It is possible to reduce metallurgical accounting and production reporting from possibly hours or even days to a matter of minutes. The result is maximization of information reliability and availability from masses of otherwise discrete and difficult to access key data.

Jan 1, 2003

By A. Sokolov, M. Demsky, E. Hasikova, V. Gostilo

"Previously, we upgraded and implemented two gamma activation assay (GAA) systems designed to analyse the gold content in raw ores at Zarafshan laboratory, Uzbekistan, and achieved a detection limit of less than 0.05 g/t under actual industrial conditions. Having started to design a fully modern, industrial GAA system for mining companies, this paper analyses the advantages, disadvantages, and special features of all major system components that can influence the sensitivity and accuracy of the analysis. The results of a study to optimize the detector geometry and sample size are presented and the performances of the linear electron accelerator, detector array, and sample transportation system of a modern, industrial GAA system for analysing gold, silver, and rare earth elements are considered. IntroductionGamma activation analysis (GAA) has considerable potential as a future replacement for traditional fire assay analysis in gold mining (Hoffman, Clark, and Yeager, 1998; Morse, 1977; Bourmistenko, 1986, 1981; Sammut, 2016; Tickner et al., 2017). The essence of GAA is to irradiate ore samples with high-energy gamma quanta generated by an electron linear accelerator (LINAC) and then to use a gamma spectrometer to detect the induced activity of the excited gold nuclei. The advantages of this method are discussed in detail elsewhere (Hoffman, Clark, and Yeager, 1998; Morse, 1977; Bourmistenko, 1986, 1981; Sammut, 2016; Tickner et al., 2017), where it is shown that GAA is uniquely suited to analysing ore samples when mining for gold, other precious metals, and accompanying elements.These advantages were realized in three industrial GAA laboratories that were commissioned in Zarafshan, Uzbekistan in 1977, in Magadan, Russia in 1979, and in Batagay, Russia in 1986 (Bourmistenko, 1986; Nii Tekhnicheskoy Fiziki I Avtomatiki, n.d). In 1989, a fourth industrial GAA laboratory was commissioned at a gold mine in Tommot, Russia. However, the project was subsequently halted due to economic reasons (Moshkov and Tjamisov, 2017). Currently, only the laboratory of the Muruntau mine in Zarafshan, Uzbekistan is in operation. The gamma activation method for gold determination is widely applicable at this mine owing to its high productivity and low cost of analysis. An outstanding aspect is the performance of more than one million analyses per year."

May 1, 2019

By V. B. Achanti

Reliability of the compressive strength of a coal seam determined in the laboratory is often subjected to debate. Effects of the coal seam's inherent characteristics, specimen preparation, testing procedure, testing condition, and a number of tests often result in drastic variation of the strength data. This paper deals with the development of a testing procedure for determination of coal seam compressive strength in the laboratory. Coal samples from two different coal seams were tested. First, the inherent characteristics of each coal seam such as coal structure, Hardgrove Orindability Index (HOI), Slake Durability Index, proximate analysis, and mechanical properties namely Young's modulus and Poisson's ratio were determined to categorize them in terms of their characteristic severity liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes namely; cylindrical and cubical, were tested to determine which shape produced the least variation of data and reproducible strength values. Third, four loading rates within the static testing range (Le. 0.007 MPa/s (1.0 psi/sec), 0.07 MPa/s (10 psi/sec), 0.34 MPa/s (50 psi/sec), and 0.7 MPa/s (100 psi/sec)) were used to determine an ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics were established.

Jan 1, 1996

By R Brake

The Enterprise Mine (EM) is located at Mount Isa and is wholly owned by Mount Isa Mines Limited (MIM). This high-grade copper mine extends from about 1000 m below surface to almost 2000 m below surface. A recent $400 million upgrade has taken the operation from a production rate of 1.3 Mtpa to a capacity of 3.5 Mtpa. The effects of high surface ambient temperatures in summer, combined with the depth of the mine and high virgin rock temperatures results in heat stress in the working place that, without intervention, would exceed the levels that human physiology can withstand. It would also result in significant decreases in productivity and high accident rates even where work is possible. Moreover, with a very hot and deep mine, the needs of æegressÆ and entrapment of workers during a mine emergency must be carefully considered. Enterprise Mine has taken a æsystems approachÆ to the issue of working productively, healthily and safely in heat. This involves setting limits of thermal stress for workers, understanding productivity decrements when working in heat, establishing productive and healthy environmental targets, developing engineering solutions to meet these targets, creating a well-educated workforce with respect to working in heat and then developing health protocols to ensure workersÆ health is protected. Refrigeration must be added to the mine to provide acceptable and productive conditions underground. By the time the mine is commissioned in 2000, Enterprise mine will have an installed refrigeration capacity of in excess of 40 MW(R). The ventilation engineering principles proven over many years at the other Isa underground mines are tailored to æfloodingÆ the mine with air to remove the heat, which is the main contaminant. This principle will not work at the Enterprise Mine, for reasons discussed below. With the underlying ventilation principle no longer satisfactory, a complete review of the entire ventilation principles and engineering solutions was required for the Enterprise Mine.

Jan 1, 2000

By Karen Talbot, Noah Maier, Rob Jameson, Giuseppe Gaspari

A storage and drainage tunnel advancing below I-75 in Detroit, Michigan experienced sudden subsidence. The Tunnel Boring Machine (TBM) was damaged to the extent that its shield, cutting head and extensive interior components needed to be extracted and replaced along with several completed tunnel segments. The tunnel was 16 feet (4.9m) in diameter with crown over 79 feet (24m) deep at the time. The tunneling contractor immediately engaged their designers and specialty subcontractors to develop a scheme to access the machine and repair the tunnel. They required a shaft 99 feet (30m) deep, with unobstructed plan dimension of 50 feet (15m) to accommodate the large components that needed to be removed and replaced. This precluded the application of an internally braced excavation and instead earth support solutions focused on use of a compression ring. Since the completed tunnel section behind the TBM obstructed closure of the compression ring below its invert, this paper describes the innovative access shaft solution employed. A conventional compression ring was constructed using 5 feet (1.5m) diameter drilled shafts down to the tunnel crown. In front of, and to the sides of the tunnel heading, the secant shafts were extended to over 150 feet (46m) depth, creating a horseshoe of support extending 50 feet (15m) below the planned excavation invert. Larger diameter "King Pile" shafts were drilled immediately to either side of the tunnel, overlapped into each end of the secant "horseshoe". The king pile shafts, together with a heavily reinforced ring beam above the crown elevation, acted as a door frame to transfer hoop loads from the incomplete secant arc into reaction supports above and below the tunnel. These oversize king pile shafts were extended and socketed into rock over 70 feet (21m) below tunnel invert. Very tight installation tolerances were necessary to maintain secant shaft alignment to depths exceeding 150 feet (46m). The project operational, geotechnical, and quality data was managed and visualized using a custom GIS interface. This paper will present the design approach employed and review the construction and quality program selected to repair the tunnel.

Oct 1, 2022

By C. H. McGuirk

Computerized Preventive Maintenance is important in maintaining consistent and efficient operation in any industry utilizing sophisticated and expensive equipment on a continuous basis. At today's large bulk materials handling facilities, the problems of continuous operation of complex machines with their thousands of components exposed to abrasion, dirt, dust and the elements, are intensified and multiplied. Effective preventive maintenance can increase profits. Yet, the number of tasks to be performed is so staggering that it is beyond error-free human capacity. The computer must be an essential ele¬ment in any efficient and economical preventive maintenance system. Computerized preventive maintenance techniques have been successfully used in many fields, usually involving highly skilled and specialized personnel working under favorable and controlled conditions. Now, The Pittsburgh & Conneaut Dock Company has developed and is applying a computerized preventive maintenance system that is applicable to the bulk materials handling industry. The "system" has taken many years of intensive effort to develop and has been time-tested and proven during the past years on equipment handling materials with rugged physical characteristics and corrosive and abrasive qualities, under some of the most adverse weather conditions on the Great Lakes.

Jan 1, 1976

These inspection standard have been prepared for use in the Federal inspection of strip mines producing, bituminous coal, anthracite, and lignite. This circular is a revision of the Safety Code for Strip Mining, which was prepared by the Bureau of Mines and employed as a guide for Federal inspectors. Numerous changes have been made in the original code to keep the in step with improvements in the industry. With continuing changes in mining methods and facilities some of these standards may become inapplicable and further revision may be advisable. Therefore, questions regarding these standards, and suggestions regarding new standards should be brought to the attention of the Bureau of Mines. Few States haves laws pertaining to strip mines, but where such laws do exist it is possible that some of the standards may conflict with them. In cases of conflict, the intent is not to advocate noncompliance with State laws, but to suggest reconsideration of such laws or safety orders.

Jan 1, 1946

By R. Adair, W. R. Hudspeth, W. T. McDaniel

ANEW method for concentrating the flake mica either from present washing plant tailings or from new feed has been developed. In this paper, flake mica refers to that which occurs in weathered granites, alaskites, pegmatites, and schists in a form too fine to be considered sheet mica. It ranges in size from 1 in. or more down to 200-mesh or finer and occurs with kaolin, quartz, and partially kaolinized feldspar. Scrap mica, a term often used indiscriminately to describe everything other than sheet mica, will be used to denote the waste product from sheet mica mines and fabricating plants. Both flake and scrap mica are used in the mica grinding plants to produce wet-ground or dry-ground mica, although some flake mica recovered from clay mining operations is fine enough to be marketed without grinding. Until 1930, ground mica was made almost entirely from scrap. From 1930 until 1935 a gradually increasing amount of flake mica was mined, and most of this was sold without grinding. A large percentage of this mica was recovered from clay washing plants. In this type of operation the recovery of any sheet mica was .of secondary importance and was considered a byproduct. North Carolina produces more flake mica than any other state, accounting for 73 pct of the total domestic production.' In the following review of current practice in jig plants, there is no intention to disparage these operations. Within the limitations under which they were built, they are examples of mechanical ingenuity. The term jig plant is a carryover from early practice since there are no jigs in operation at the present time. Current practice, as shown in Fig. 1, is based on successive stages of differential crushing with rolls followed by trommel screens to remove the more easily crushed gangue minerals. The oversize mica product then is usually dried, and passed through another set of dry rolls and a final screen to remove the remainder of the grit. This process is effective in recovering up to 50 pct of the mica in the original ore, the balance being lost in the screen undersize, usually —% in. Jigs and tables were at one time used to treat this screen undersize and were capable of recovering a part of the mica larger than about 60-mesh.V ine mica lost in these plants is normally washed away in streams and can be considered irrecoverable. There are ten or more washing plants in the North Carolina area that are losing approximately 50 pct of the mica in the feed. Since the three cooperating agencies, the Asheville Minerals Research Laboratory of North Carolina State College, the North Carolina Dept. of Conservation and Development, and the Tennessee Valley Authority, are concerned with conservation of minerals, they have investigated means for improving the efficiency of these mica plants. The mica industry has been cooperating fully with the laboratory to establish a more efficient method of recovery for flake mica. Choice of Methods The initial investigation was concentrated on finding a means of reducing the losses from plants now using the conventional flowsheet shown in Fig. 1. To accomplish this it would be necessary to collect the screen undersize products through the plant and remove from them the mica from Vs in. down to

Jan 1, 1952

By F. Baczek, S. S. Rocks, D. Chaiko, C. Eyzaguirre, S. Asihene, T. Walters

The majority of efforts to improve primary copper sulfide leaching have focused on solution chemistry, temperature, O2 pressure, ultra-fine grinding, the use of catalysts, etc. Historically, very few studies have focused on the solid/solution interface. A new, patent pending approach to catalyzed, copper sulfide leaching has been discovered by FLSmidth that enables manipulation of the 2-D semi-conductor properties of chalcopyrite surfaces to the benefit of higher electrochemical reactivity. Copper dissolution rates are then further accelerated by incorporating a Stirred Media Reactor (SMRt) into the process. By using minute amounts of Cu2+ to "pre-activate" chalcopyrite, leach times have been reduced from >20 hours with incomplete Cu dissolution to <2 hours with 98+% Cu dissolution at 80°C. The pre-activation process takes only minutes to complete at temperatures of 80°C or less. The total atmospheric leaching process, incorporating the pre-activation and Stirred Media Reactor is compatible with existing SX/EW processes. Results of batch leach testing are presented and possible mechanisms are discussed.

Jan 1, 2015

By D. J. Englund, R. A. Davis

"A three-dimensional CFD model of a straight grate furnace for indurating iron-oxide pellets was developed for exploring conditions of furnace operation for fluid flow, heat transfer and reactions. The model includes reactions for natural gas combustion in the gas phase and calcination and magnetite oxidation as well as drying in the pellet bed. The performance of the model was investigated with a series of pellet production rates that included adjustments to the fuel rates to achieve proper induration temperatures in the pellet bed. The model may be used to discover opportunities for process improvement.IntroductionIron oxide pellets are a feedstock to blast furnaces for iron making. Pellets require physical strength characteristics needed to maintain their integrity during storage, handling, transportation and smelting. Pellets are produced from iron ore in a series of mineral processing operations that form wet green balls from slurries of iron-ore concentrate with binders, such as bentonite, and possibly fluxing-agents such as limestone and dolomite. The green balls are dried, fired at high temperature, and then cooled in an induration furnace to achieve the strength and chemical composition required for efficient reduction and slag separation in blast furnaces. Induration furnaces are generally straight grates or grate-kilncooler configurations. These furnaces operate with pellet beds passing through a series of temperature zones to control drying and chemical reactions in the bed.Process air passes through the zones in an overall counter flow direction to the pellets for efficient heat transfer and energy recovery from the cooling stage. Consequently, the zone conditions and the overall furnace performance are highly coupled. Thus, it becomes challenging to predict how changes to any single zone may affect the rest of the furnace. To gain a better understanding of machine performance and coupling, a three-dimensional, steady-state model of a complete straight grate induration furnace was created using computational fluid dynamics (CFD)."

Jan 1, 2015

By O. Jay Myers

THE war effort has furnished the necessary impetus for better magnesium foundry practice. Four or five years ago, there were but a few formulas in general use for cores and mixtures for magnesium castings. Certain sands, binders, and inhibitors were specified and the proportions of these materials in each mixture were maintained between very narrow limits. As more and more war industries entered the field, much research was carried out and methods and practices were improved. Magnesium founding is still in a state of flux; therefore it is not uncommon to find one foundry spraying inhibitors on its cores, and another foundry using sand mixtures with incorporated protective agents. The basic core or dry-sand mold mixture for magnesium in use today is compounded with sand, core oil or resin binder, cereal, and moisture. Core oil or resin binder are added for baked strength while the cereal binder and moisture are for green strength. The normal mixtures (based on the weight of the sand) contain from 0.5 to 1.5 per cent of both cereal binder and core oil, and the moisture content varies between 1.5 and 5 per cent. The ratio of core oil to cereal binder varies from 60:40 to 40:60, while the correct amount of moisture depends upon the method of coremaking. PROTECTIVE AGENTS In all magnesium practice, protective agents are used in conjunction with the core and molding sands to prevent oxidation of the metal. The use of these inhibitors is not novel, but publications covering this field are not entirely adequate. Beck1 says Magnesium alloys decompose water to form magnesium oxide, hydrogen being liberated in the process (Mg + H20 -+ H21 + MgO). This reaction results in the blackening of the skin and the appearance of areas of porosity on the casting surface, the cavities of which are filled with a grey oxide powder (these are termed `burns&apos;). Although sand cores for magnesium castings are thoroughly dried during the baking cycle, burning will take place on the castings unless the metal is protected properly. This type of burning is more difficult to define than the "water-magnesium" reaction cited by Beck. A possible explanation may lie in the following equation: 2Mg + 02 -s 2MgO Here, the source of the oxygen is not water, but the air in the mold cavity, together with the chemically combined oxygen in the core-binding media. Generally, two methods are used to prevent this reaction from taking place.

Jan 1, 1945