Search Documents

By George T. Faust, S. R. B. Cooke

"The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the preparation of pulverized coal for fuel. In this study the relative amount of surface in various products and samples had to be assessed. Because of the familiarity with screens and because of the simplicity of using the inverse ratio of the opening for ascertaining the amount of relative surface in the respective sizes, screens down to and including 270-mesh were used. This choice was made in full cognizance of the irregularity of screens, but it seemed that if the same screens were used throughout all the tests the relative values would be satisfactory.In dealing with the subsieve sizes, pneumatic elutriation was used to make several fractions to extend the sizing analysis into the range of hypothetical screens. This kind of a sizing analysis was thought necessary because it is familiar to all operators, and, furthermore, it is amenable to several ways of plotting curves that bring out the characteristics of various coals and various methods of grinding.The method of obtaining the data from which to set up the hypothetical screen scale is the subject of this paper. It consists in determining the average projected area of the particles in the respective elutriated products. By extending the ""area method"" to sieve sizes, a factor is found that may be applied to the subsieve sizes, and thus the scale is projected in a regular manner. This method avoids contentions about specific surface and steers clear of ""average diameter"" except as material sized on screens may be said to have an average diameter."

Aug 1, 1939

By James P. Roe

Steel has occupied such a prominent position in most minds during the last thirty years, particularly since the introduction of the basic open-hearth process (by which the field from which the raw material could be obtained has been so widened), that little attention has been made to improvements in puddling iron. In fact, the general tendency seems to have been to accept the prediction that puddled iron is doomed. Events have in a measure justified such a forecast, due in large part to the introduction of mechanical appliances and operations with large units in the manufacture of steel, from which much lower costs have resulted. But this general tendency has met checks in certain directions. This is notably the case where the finished product is a welded one, or is subject to oxidation, to shock or to vibration; and, as far as the writer's observation goes, the bond (which is largely a mechanical one) is not as close and lasting between steel and tin or zinc as between iron and the same materials. The field still open for puddled iron is, therefore, a large one, provided the low costs of steel-manufacture can be approached. The process of puddling is one of the most interesting in the metallurgy of iron, as the reactions and the changes effected are apparent. The subject has had the strongest fascination to the writer from boyhood, and has led, not unnaturally, to a close study, which long ago resulted in the conviction that it could be successfully carried out with large units and by mechanical means. That others have also drawn these conclusions is shown by many undertakings, though there have been few such attempts during the last twenty-five or thirty years. Puddling cousists, essentially, in the removal of most of the carbon and silicon, and part of the phosphorus and sulphur

Jan 1, 1903

By H. R. Barnhurst

It would be a difficult matter to trace from the beginning the very few improvements made in the burning of fuels prior to 1860. Donbtless the crossing of the sticks of wood in building a mood fire early appealed to our savage ancestry as a means of expediting its effectiveness for their crude culinary purposes. Stones and andirons came later in assisting the admission of air to the under part of the fuel bed, while beacons and cressets, utilized metal bars as supports for the same purpose. It is probable that Tuba1 Cain owed his success to the use of bellows making possible the use of mixed fuel and charge upon a hearth. With the development of working in cast iron, grate bars came in, and they are still with us doing duty in every household and almost every art where heat is a factor. Little was done beyond these crude methods prior to 1860. With the advancement of knowledge came the fuel-gas producer, a natural child of the retorts employed in supplying illuminating gas. It is only within the last 15 years that the conclusion became general that complicated systems for saving heat would not remedy deli-. ciencies in its primary development, and within that time there has been great advancement in the means of producing initially a fire of high effciency, so that to-day we are moving rapidly toward both high development and high absorption, with the resultant of high efficiencies. In studying the subject of the availability of pulverized coal as a fuel, it may occur to ask, why has this not come up earlier? This, question would be naturally prompted by recalling the fact that Thomas Crompton's English patents upon his methods were issued to him nearly 40 years ago. A conclusive answer to this, however, is that Crompton at that time had very crude facilities for making what was at best a very imperfect pulverization of the coal, arid the expense of preparation mas very great. He does not seem to have been aware of the advantage of a thorough drying of the coal in the

Jan 1, 1914

By S. W. Beckman, L. Williams, A. E. Seep, R. Fischer, J. Hubbard

Introduction The Summitville Mine located in southwestern Colorado was added to the National Priorities List in June of 1994. Summitville was the site of mining operations that began in 1873 with the discovery and development of gold placer and lode deposits in the late 1800's. The mine site is located about 25 miles south of Del Norte, Colorado in the San Juan Mountains adjacent to the Rio Grande National Forest at an approximate altitude of 11,600 feet. The site was mined for gold, silver and copper between 1873 and 1947. The Summitville Consolidated Mining Corporation, Inc. (SCMCI), a wholly-owned subsidiary of Galactic Resources, Ltd of Vancouver, Canada ran a large tonnage open-pit mine and cyanide heap leach operation from 1986 to 1992 (Pendleton and Posey, 1992) During the mine operation by SCMCI, approximately 10 million tons of gold ore was mined, crushed and stacked on a lined leach pad. Heap leach operations experienced water balance and unplanned solution discharges from the start of the mine life. Despite the production of 249,000 troy ounces of gold during the mine operation, SCMCI was unable to meet remedial requirements and notified the state of Colorado of its intention to file a Chapter VII bankruptcy in December 1992. The EPA Region VIII Emergency Response Branch took over site operations on December 16, 1992 to prevent a catastrophic release of hazardous substances to the environment. The multiple contamination sources at the mine site are due to both historic and SCMCI mining operations. Emergency response operations at the site have prevented releases of severely contaminated solution and a permanent treatment for all waste units at the site is under investigation. A Request for Proposal (RFP) was issued in October 1993 by Environmental Chemical Corporation (ECC) at the Request of EPA Region VIII, Department of the Interior and Bureau of Reclamation. The RFP requested that interested companies provide information on their ability to implement innovative treatment technologies to improve treatment efficiency and reduce treatment costs for remediation of the heap leach pad (HLP) spent ore and ore leachate solutions. Dames & Moore and Pintail Systems, Inc. (PSI) jointly submitted a proposal suggesting application of biotreatment processes for detoxification of cyanide in spent ore and HLP leachate solutions. The proposal was accepted for pilot and field demonstration under the SPA Superfund Innovative Technology Demonstration Program (SITE) with additional funding from EPA Region VIII. This report discusses the test program and results of a Focused Feasibility Study which demonstrated biotreatment processes for spent ore cyanide detoxification.

Jan 1, 1995

By A. J. Lewis, P. J. Hutcheson, M. E. Robertson, P. A. Moir, K. M. Barfoot

With the content of gold and platinum in the vast majority of ore deposits typically averaging 6 parts per million and less, the accurate and precise measurement of these metals in samples of ore and mining process streams has proven very difficult to achieve by modem spectroscopic analytical techniques. Largely because no other technique has proven suitable, the basic fire assay process has become the accepted international standard for these metals. Fire assay, however, suffers a number of disadvan­tages in the modem, competitive, high technology, and increas­ingly environmentally aware world. It is a labour intensive technique that is difficult to automate, and requires high levels of skill to ensure accuracy and consistency of results. Potentially hazardous chemical reagents are employed, of which, lead, in particular, can be a serious source of contamination to both personnel and the environment if not effectively controlled. Other dangerous elements, such as mercury and arsenic, liberated in high energy furnace operations, are further sources of possible health and pollution hazards. n contrast, the energy dispersive K X-ray fluorescence (K­XRF) technique devised by K X Technology Ltd overcomes many of the technical constraints of conventional low energy X­ray analysis, and has the potential to revolutionise assay opera­tions in precious metal mining. The technology is simply automated, requires basic operator skills, uses no chemicals, consumes less than 20kW, and is capable of detecting gold and platinum to an accuracy of O .1 parts per million by mass. The new third generation design of AZTEC laboratory instrument, released in 1994, is the result of significant technical development. Capable of analysing over 1200 samples per day, and developed primarily for grade control sampling, its applica­tions have spread to gold ore accounting from on-line conveyor belt sampling; screening of exploration samples; measurement of gold in carbon granules for Carbon-in-Pulp process control; and for conducting rapid checks to support key managemen decisions. The economic, rapid, and non destructive analysis ofup to 80g of ore for large numbers of samples, reduces sampling and sub-sampling errors, and provides improved grade estimates for ore bodies. When interfaced to a LIMS, laboratory automation and cost-savings can be further enhanced. The AZTEC design is also being modified for the analysis of platinum. The GOLDSTREAM on-line analysis system is an important new application of K-XRF to the continuous monitoring of process streams in gold ( or platinum) plants and mills. Integrat­ing the technologies of K-XRF to measure total gold, and dissolved gold spectroscopy to measure gold in solution, the insoluble fraction of gold can be deduced, and the effectiveness of the extraction process determined. Slurries are sampled automatically from selected points of the plant and pumped to the system for analysis. The information produced forms the basis for plant control and optimisation.

Jan 1, 1995

By D. B. Mazzinghy, L. C. de R. Machado, H. Delboni, M. G. Bergerman

"The use of vertical stirred mills in the mining industry has increased remarkably over the past few decades, as a result of growing requirement for finer ore grinding. This equipment delivers higher energy efficiency in fine grinding operations when compared to conventional tubular mills. Methods for designing vertical stirred mills involve operational experience, pilot plants and bench tests. An important issue is that these tests require, at a laboratory scale, at least 10–20 kg of material, depending on its density, which is not available in many cases, particularly in the early stages of greenfield projects. For the regrind of flotation concentrates, several bench scale flotation cycles are required to generate such a sample. This paper describes the development of a laboratory jar mill test using a 6”x8” jar – smaller than that commonly used – based on the overall specific energy method, which requires significantly less mass compared with existing tests. The proposed test has proven to be more practical than tests normally used, requiring about a quarter of the mass, and also shows good adherence to industrial results for the studied iron ore processing plant. INTRODUCTION A significant demand for finer grinding has been noticed over the past few decades in several mining projects to achieve the mineral liberation required for the concentration of valuable minerals. However, the finer the product size, the greater the grinding energy consumption, resulting in an overall increase in operating costs, which may reach or even exceed 50% of the mineral processing cost (VIEIRA, PERES, 2013; DANIEL, LEWIS-GREY, 2011). Comminution technology can have a major impact on subsequent ore concentration stages (DANIEL, LEWIS-GREY, 2011; MARSDEN, 2009; NAPIER-MUNN, 2012; PEASE et al., 2010), which further strengthens the importance of proper technology and equipment selection. Adequate grinding circuit selection and design is thus a key aspect associated with mining projects."

Jan 1, 2018

By Blake M. Caldwell, Thomas C. Poulter

A new approach to an old problem has made it possible to do in a a tively short period what has not been accomplished in the past three quarters of a century using strictly experimental methods. A theoretical study was made of the underlying principles whereby a jet is formed by a shaped charge and of the mechanism of the penetration of the target by that jet. It was found that there are more than 10, and perhaps as many as 15 variables affectin!? the performance of the shaped charge. Only a few calculations are necessary to show that it is physically impossible to investigate all of these variables experimentally. The shaped charge theory has been extended to include a previously little-understood mechanism in high explosive phenomena; namely, low order detonation. By superimposing a high order detonation on a zone already undergoing low order detonation, all appreciable improvement in performance is accomplished. The development of a design wherehy these phenomena are coordinated in such a way as to develop a jet which is tailored to meet the specific target requirement will be described in detail. The shortcomings or even impossibility of strictly experimental techniques will be illustrated by a discussion of the development of a special-purpose explosive charge. INTRODUCTION In an article appearing in the May, 1888 issue of Scribner's Magazine, Charles E. Monroe described his early experiments with gun cotton (Fig. 1) which led to his name being most fre-quently connected with our present-day shaped charge. Although the sunken letters or "cavities" in Mon- roe's gun cotton were not lined, they produced some penetration of an iron plate. The credit for the lined shaped charge, however, should rightfully go to Dr. R. W. Wood of the Physics Dept. of Johns Hopkins University, who was responsible for first discovering the fact that a metal liner in a cavity of explosive gave high velocity fragments and/or jets of metal. This discovery was made by Dr. Wood inadvertently while investigating an accidental death resulting from an electric blasting cap. He discovered that a jet of high velocity copper particles was ejected from the dimple

Jan 1, 1958

This publication contains 10 papers presented at a symposium on ATRS systems in Charleston, WV, on June 23, 1983. Included are papers by MSHA Technical Support (Roof Control), West Virginia Institute of Technology, the Bureau of Mines, and seven roof bolter manufacturers and/or designers of ATRS systems. These papers summarize the most recent developments in ATRS technology and can serve as a guide to potential designers, developers, and users of ATRS systems.

Jan 1, 1985

By Walter Valery, Lauren Hafla, Megan Tibbals, Adrian Dance, Jeff Snyder

"Newmont Mining Corporation’s Carlin (“Carlin”) operation processes roaster feed through a double rotator, dry grinding mill following secondary crushing. Metso Process Technology & Innovation (“PTI”) was involved in a review of crushing and dry grinding circuit operations in August 2009. A number of opportunities for increased throughput were identified in the PTI study.Extended plant trials were conducted in July 2010 to provide justification for possible circuit modifications and if needed, additional equipment. The trials confirmed that a finer crusher product would reduce the build-up of material ahead of the coarse grinding chamber in the double-rotator. Also revealed were material transport and airflow restrictions in the dry grinding circuit that resulted in a high circulating load.The secondary crushing plant demonstrated it was capable of reducing the amount of +¾” material in the mill feed thus increasing dry grinding throughput. However, wet and sticky feed affected screening efficiency resulting in low utilisation of the existing crusher capacity. The open circuit configuration also made it difficult to control crushing circuit product size.For the dry grinding circuit, changes in grinding media size, transfer grate design and increased airflow were recommended to reduce circulating load issues and increase circuit capacity. This paper summarises the crushing and grinding circuit review, the extended site trials performed by PTI and the improvements in dry grinding operation that resulted from this study."

Jan 1, 2012

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Marc Lemieux

Computer pit design techniques generally make use of models in which the deposit is represented by a regular array of data. Using a regular system, the number of data points required to represent the air, waste and mineralization in a large deposit become excessive. The number of blocks used to describe the deposit is dependent upon the block size. The quality of the pit wall slope design also is dependent upon the block size used and the method of defining the slope. The error associated with reserve calculations becomes greater with increasing block size. A deposit model consisting of variable sized air and mineralized blocks has been developed at the University of British Columbia and improved upon at Climax for pit design work. The method permits put- ting the entire model in core for rapid data processing. This permits the use of a versatile cone generation technique which allows close adherence to variable slope constraints in all directions. The conical shape is approximated by rectangles on each level which equal the area of the ideal conical intersection. The shape of the intersection may vary from approximately circular to elipsoidal. The approximate cone shape is controlled by the slope constraints applicable at the point of intersection on the bench. The overall modeling technique greatly assists the pit design engineer in developing a high quality pit design.

Jan 1, 1977

OWING to the gradual depletion of the hitherto plentiful supply of firewood in the immediate vieinity of Queenstown and Gormanston, which caused a steady increase in the cost of fuel for domestic purposes, the Mount Lyell Company took steps several years ago to make available as a substitute electric current from its Lake Margaret hydro-electric supply. In order to make this practicable it was necessary that the cost of electric power for heating purposes should compare favourably with the cost, of fuel, and the installation of domestic appliances brought within reach of the average householder, and efforts have been continuously directed towards this end since the year 1928.WATER HEATERSThe installation of electrical apparatus in local dwellings began with hot-water services, the heating elements being the types then procurable on the market and adapted to meet requirements.These, however, did not prove satisfactory, but the study of their bilure resulted in a type being developed locally which has overcome all difficulties. The first type of water heater evolved was an outside circulation one the element of which consisted of an iron pipe through which the water passed, insulated with micanite and wound with nichrome wire, the latter being covered with alundun cement to keep it in position and prevent oxidation. This was insulated on its outside surface with a layer of asbestos flour, and connected to the hot-water container as shown in Fig. 1. It was found, however, that the iron pipe had a short life, due to a certain amount of acidity in the water, and a copper pipe was substituted which proved very durable. Some heaters with this improved type of element are still operating after six years of use. The resistance wire is run at a very low current density, which ensures durability.

Jan 1, 1927

By A. J. Langhammer

Broadly speaking, it may be said that the engineer has two major responsibilities: One is to recommend the choosing of proper machinery and equipment; the other, to assist in the simplification of design, determination of method, and advise about the most suitable material to be used. The products of powder metallurgy enter broadly into both these fields. The oil-cushion, self-lubricating bearing surface on a machine part makes for better machinery and factory equipment, often proves a life-saver in curing difficulties where bearings are overloaded or inaccessible for lubrication, or on installations that with normal practice constitute a problem entailing frequent repairs. On the other hand, other parts may require low porosity approaching solidity. In the second field, powder metallurgy provides many possibilities for improved products, improved performance, solving of technical problems, saving of weight, quiet operation, higher factors of safety, greater flexibility, attractive economies, and so on. Parts We of the automotive industries are making many powdered-metal war-machine parts, both ferrous and nonferrous, including gears, external and internal; ratchets, both external and internal; levers; pillow blocks; sliding blocks; cams; gibs; hubs with external and internal splines, and similar units. Powdered metals play an important part in our war work, as they did in peacetime in the manufacturing of passenger cars and trucks. The art of powder metallurgy is not a panacea. Although on certain parts such operations as turning, boring, facing, reaming, counterboring, milling, countersinking. chamfering, broaching, hobbing, profiling. trepanning, gear cutting, grinding, etc., can be eliminated, there will always be the need for machine tools. Advantages of Powder Metallurgy Simple machining operations often are eliminated by using powdered metal, and also many other intricate operations, some of which are of the type impossible to perform on the most modern production equipment; for instance, an external spline on a flange hub, where the spline must continue to the flange face and at full depth. Another important feature is that some of the machine parts may require a self-lubricating surface at one or more points; for example, proper lubrication of a sliding splined spool, while ordinarily most digcuit, is accomplished automatically with a self-lubricating powdered-metal bearing. Frequently machine parts are made with physical, mechanical and technological advantages unobtainable from cast or forged metals of similar analysis. Thus powder metallurgy offers the designing engineer broader latitude. Similarly, the engineer may take advantage of powder metallurgy in his teamwork with other departments. Another important advantage in powder metallurgy for machine parts is the relatively short time required for tool-up.

Jan 1, 1945

By George M. Rigg, Samuel M. Cassidy

During 1937 a program was begun to mechanize and modernize the then 28-year old Isabella mine of the Weirton Coal Co., which is on the Monongahela River, in Fayette County, Pennsylvania, at one edge of what is generally known as the Coke Region. Weirton Coal Co. is a subsidiary of the National Steel Corporation, and produces metallurgical grade coking coal for the Weirton Steel Co., Weirton, W. Va. Improvements subsequently made included a cleaning plant for washing the entire mine output, shovel-action track-mounted machines for mechanically loading all the coal, universal-type track-mounted cutting and shearing machines, post drills, 8-wheel mine cars of 10 tons capacity, cable-reel gathering locomotives and other auxiliary equipment. This paper presents the factors, reasons and results of decided changes from the mining system generally prevailing in the region, as well as abandonment of selective mining practices in favor of complete seam extraction. Coal-seam Conditions Fig. 1 illustrates the Pittsburgh coal seam on the property. Cover over the seam averages 450 ft., and 675 ft. is the maxi- mum. Main roof varies from very weak to medium strong; usually it disintegrates rapidly on exposure to air. The "wild" coal makes a fairly strong immediate roof if supported by crossbars and if unbroken affords a seal to the main roof. The draw slate is very weak and treacherous. The floor is characterized by numerous irregular bottom rolls, or "horsebacks," protruding from a few inches up to 3 ft. into the coal. Some are soft, but many are hard and flintlike. Although the bottom slate usually is hard, the underlying fire clay causes it to buckle and heave readily with any moderate increase in roof pressure or where damp. As a whole, the bottom is weaker than the main roof. The coal is characterized by numerous closely jointed face and butt cleats and a woody, springy nature when shot, both having a decided influence on face practices. As shown in Fig. I, at both the top and bottom of the main coal seam is a layer of coal of higher ash and sulphur content than the body of coal in the middle. Factors That Influence the Mining System Equipment was bought and organization for mechanical loading was made on the basis of working each mechanical unit as near its full capacity as possible, to lessen investment cost and obtain best operating efficiency. This led to combination double and triple-shift operation at the start, and, very shortly, to all sections being triple shifted.

Jan 1, 1947

By Samuel M. Cassidy, George M. Rigg

During 1937 a program was begun to mechanize and modernize the then 28-year old Isabella mine of the Weirton Coal Co., which is on the Monongahela River, in Fayette County, Pennsylvania, at one edge of what is generally known as the Coke Region. Weirton Coal Co. is a subsidiary of the National Steel Corporation, and produces metallurgical grade coking coal for the Weirton Steel Co., Weirton, W. Va. Improvements subsequently made included a cleaning plant for washing the entire mine output, shovel-action track-mounted machines for mechanically loading all the coal, universal-type track-mounted cutting and shearing machines, post drills, 8-wheel mine cars of 10 tons capacity, cable-reel gathering locomotives and other auxiliary equipment. This paper presents the factors, reasons and results of decided changes from the mining system generally prevailing in the region, as well as abandonment of selective mining practices in favor of complete seam extraction. Coal-seam Conditions Fig. 1 illustrates the Pittsburgh coal seam on the property. Cover over the seam averages 450 ft., and 675 ft. is the maxi- mum. Main roof varies from very weak to medium strong; usually it disintegrates rapidly on exposure to air. The "wild" coal makes a fairly strong immediate roof if supported by crossbars and if unbroken affords a seal to the main roof. The draw slate is very weak and treacherous. The floor is characterized by numerous irregular bottom rolls, or "horsebacks," protruding from a few inches up to 3 ft. into the coal. Some are soft, but many are hard and flintlike. Although the bottom slate usually is hard, the underlying fire clay causes it to buckle and heave readily with any moderate increase in roof pressure or where damp. As a whole, the bottom is weaker than the main roof. The coal is characterized by numerous closely jointed face and butt cleats and a woody, springy nature when shot, both having a decided influence on face practices. As shown in Fig. I, at both the top and bottom of the main coal seam is a layer of coal of higher ash and sulphur content than the body of coal in the middle. Factors That Influence the Mining System Equipment was bought and organization for mechanical loading was made on the basis of working each mechanical unit as near its full capacity as possible, to lessen investment cost and obtain best operating efficiency. This led to combination double and triple-shift operation at the start, and, very shortly, to all sections being triple shifted.

Jan 1, 1947

By J. V. Batty

The Bureau of Mines devised techniques involving the use of beta-and gamma-ray-emitting radioisotopes and successfully adapted these techniques to the density of mineralized flotation froths) the rate of flow of finely ground ore pulps) and the residence time of pulps in processing circuits. Specifically, the water and mineral loads of flotation froths were continuously measured by determining the proportion of a constant-strength beam of beta rays that was absorbed by the froth column. Continuous measurement of the rate of flow of an ore pulp was accomplished by measuring the changing width of a free-falling stream of the pulp with a collimated beam of beta rays. The residence time of solids in conditioning and resin-in-pulp circuits was accurately measured by following the progress through these circuits of a portion of the pulp that had been tagged with the gamma-emitting Ag110 radioisotope.

Jan 1, 1966

The performance of two large-capacity ventilation systems was compared through tests conducted in a large dead-end heading at a pilot oil shale mine in Colorado. Sulfur hexafluoride (SF6) tracer gas was used to measure the performance of the two systems: a free-standing jet fan and a reversible fan with rigid duct. The tracer gas was used to simulate the production of mine air pollut-ants, including blasting pollutants, hot diesel emissions, free methane from surrounding strata, and methane desorbing from muck piles. The test room was 55 ft wide, 30 ft high, and 320 ft long. The performance of the two fans was similar, but the jet fan used less power. The tests showed that either system could provide effective ventilation during oil shale mining.

Jan 1, 1986

By G Chitumbura

Raise boring is a critical aspect of mining at Xstrata Copper’s Mount Isa Copper Operations (MICO). MICO’s internal raise boring department regularly develops ventilation rises, orepasses and stope cut-off rises and reams approximately 2500 m per annum. Developed, trialled and implemented as standard practice over the past two years, procedural changes in constructing the raise bore machine’s foundations have significantly reduced operator exposure to raise boring’s inherent risks of working around open holes and manual handling. An additional cost benefit of this newly-adopted procedure is derived from reducing the likelihood of damaging the machine while de-rigging.When conforming to standard industry raise boring practices, exposure to an open hole begins when the reamer breaks through the concrete pad and ends when it is removed from the hole – a process which, depending on the size of the hole and the raise boring machine, can take up to three days to complete. Although wearing fall restraint equipment, operators working on and around the raise bore machine during de-rigging are continually exposed to the risk of falling from heights. In contrast, MICO’s newly-developed and successfully-implemented presink raise boring system reduces this exposure to a maximum of four hours, regardless of hole size. Exposure to manual handling hazards is also substantially reduced as the presink procedure eliminates manual placement of a 100 kg drill bit under the machine to commence pilot-hole drilling. Outcomes of implementing the presink System at MICO have been so beneficial that it is now standard procedure for all reaming in excess of 1 m diameters.

Mar 21, 2011

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By Frederick B. Brien

For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present-low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Bolivia today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since appropriate heavy liquids are available and with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined.

Jan 1, 1964