Search Documents

By J. A. Cox, R. S. Mattson

"One of the main problems encountered in employing sublevel caving is the inherent high dilution factor. The operating results at Granduc illustrate that this dilution can be closely controlled and satisfactory recoveries achieved, in base metal ores grading less than 2.0% copper equivalent, by using an assay grade control system based on the fundamental draw characteristics. The history of draw control procedures employed since the start of operations provides an effective comparison between this system and one based mainly on tonnage. The transverse and longitudinal sublevel caving mining methods are described and it is shown how improvements in design layout, operating practice and draw control in narrow complex ore zones (12-foot minimum width) have raised the operating performance of the longitudinal system to a satisfactory level."

Jan 1, 1973

By Robert W. Carn

This paper presents the concepts which are presently being utilized in the design of coal export terminals. Criteria for selecting a viable site and establishing the terminal plan are presented. Factors affecting the design of the terminal as well as the present techniques and procedures in use today to determine the optimum use of equipment will be discussed along with the current trends in export terminal control systems. Finally capital and operating costs for a typical export terminal are reviewed.

Jan 1, 1982

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"We have used the microscopic thin balance developed by Scheludko at al. (1970) technique to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetime, compared to the pure amine system.This behavior was explained by the initial strong adsorption of positively charged interfacial complexes from the mixed surfactant system at the air/solution interface followed by adsorption at the silica interface. It was also shown that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex, determining an inhibition in the thin film rupture and dewetting of the film. The rupture mechanism was explained by an earlier established heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface which remained negatively charged. The formation of the interfacial complex at the air/solution interface was confirmed by using surface tension data."

Jan 1, 2003

By J. W. Peirce

Advances in instrumentation now make it possible to measure accurately flaw of such difficult-to-mea-sure liquids as mining slurries. A mass flowmeter, which introduces no restrictions in the line, will measure the mass flow of slurry equal to the volume flow times the mms/unit volume. In the mass flowmeter system a volume flow measurement is electrically multiplied by a density measurement in order to give mass flow. Fig. 1 shows a typical mass flow measuring system. The volume flow is measured by a magnetic flowmeter and the density is measured by a gamma gauge cell, neither of which have any restrictions in the line. Consequently, there is no clogging and no more loss of head than there would be in a similm length of standard pipe. None of the parts extend into the flowing stream and there are no moving parts in the measuring elements. PRINCIPLE OF OPERATION OF THE VOLUME FLOW TRANSMITTER The magnetic flowmeter, which is used for the volume measurement, operates on the principle of a generator (Fig. 2). This principle states that when a moving conductor cuts lines of force in a magnetic field, a voltage is induced in it. Moreover, if the dimensions of the conductor remain constant, then the induced voltage is directly proportional to the velocity of the conductor. Since the voltage is strictly a function of flow velocity, the transmitter output can in no way be influenced by such factors as temperature, viscosity, turbulence, or conductivity. The linear output is detected by flush mounted electrodes (as shown) and transmitted to a potentiometer flow receiver. Magnetic Meter Construction: The metering tube is constructed of nonmagnetic stainless steel. (See Fig. 3.) To prevent shortcircuiting of the generated voltage, the tubes are lined with a suitable liner, depending upon the corrosive, erosive or other properties of the liquid or slurry to be measured. A uniform magnetic field is produced by two saddle-shaped coils of insulated copper wire. A laminated iron core focuses the magnetic field at a 90' angle to the flowing liquid. The voltage generated by a flow of liquid through the magnetic field is detected by two point electrodes mounted flush with the inner wall of the metering tube, 180' apart. Electrodes are made of Type-316 stainless steel or other material suitable to the application . Volume Flowmeter Operation: The millivolt output of the metering transmitter is transmitted to a potentiometer-type receiver (Fig. 4). The self-balancing, self-standardizing receiver has a drive unit for circuit rebalancing. The measurement change imposes an unbalanced input on the twin windings of the drive unit. The resulting unequal pull on a segmental rotor provides the motion which drives a pen, while simultaneously and steplessly repositioning a rebalancing element. Changes in conductivity have no effect on the accuracy of the measurement or the calibration of the instrument. The minimum conductivity values are determined by the length of the transmission cable and the size of the transmitter. They can be as low as five micro mhos, since there is such a small load on the electrodes. Because the meter electrically averages all of the incremental velocities in an irregular flow profile, it is ideally suited for turbulent flow and suspended solids. Straight runs of pipe are therefore not required. The transmitter can be installed close to

Jan 1, 1962

By W. G. Bradley

THIS PAPER describing the quarrying, mining, and crushing of gypsum at the Blue Diamond mine, 11 miles from Arden, Nev., on the Union Pacific Railway, is one of a series on gypsum mining being prepared for and published by the Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total production costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By K. J. Shoop

An analysis of an iron ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency in the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Experiments were divided into two groups: 1) Drop testing, which was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. 2) Wet grinding, which was further divided into laboratory tumble tests and pilot plant scale tests. Laboratory tumble tests were performed to determine the effect of temperature on the grinding of iron ore. This was done by varying the percentage of fines and percentage of metamorphic clay material added to the iron ore grinding charge. The pilot plant scale tests were conducted as a scale-up of the laboratory tumble tests and to determine the effect of temperature on slurry rheology, and how this changing rheology affected the grinding of iron ore. The combined results of drop testing and wet grinding were used to make some predictions of the performance of plant scale autogenous grinding. In drop tests the breakage characteristics of the iron ore had no noticeable change in size stabilities for dry and water saturated samples over the temperature range studied (-25°C to 25°C). The effect of frozen pore water was not observed due to the low apparent porosity of the iron ore. The addition of fines to the test charge caused a decrease in the amount of new fines produced for both the laboratory tumble tests and pilot plant scale tests. The production of fines further decreased when tests were performed at the colder temperature. The increased energy consumption at lower temperatures was dominated by rheology phenomena. The addition of metamorphic clay material to the iron ore test charge resulted in more fines being produced in the laboratory tumble tests. This was due to the metamorphic clay material grinding easier than the iron ore. This caused an increase in the amount of fines in the mill, which in turn, would prematurely slow down the grinding of iron ore because of an increase in the viscosity of the slurry.

Jan 1, 1995

By P Kappen, R N. Collins, K M. Spiers

X-ray absorption spectroscopy (XAS) is a synchrotron-only technique used to determine chemical speciation, providing a powerful alternative to most traditional ‘wet chemistry’ and lab-based speciation methods. XAS is an element specific method that can be used to address a variety of systems, ranging from heterogeneous to homogeneous, polycrystalline to amorphous, and solid to liquid. The strength of XAS in identifying and managing chemical species in tailings and mine waste is demonstrated, with the presentation of highly relevant studies into lead, uranium, chromium and arsenic speciation. In each example, waste samples are compared with known standards, allowing an assessment to be made of the quantity of particular chemical species in each.CITATION:Spiers, K M, Collins, R N and Kappen, P, 2015. ‘Forget the wet chemistry’ – how the Australian Synchrotron can help with tailings and mine waste management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D R. Seaman, R P. Tooher, B A. Seaman

"Several mine scheduling tools exist for use in optimising and scheduling the reserve according to in situ value. These tools generally value the ore on a per block basis according to regressed recovery models based on ore grade and type. It is then the task of the plant metallurgist to ensure that these ore blocks are fed to the plant in a manner that satisfies the prevailing plant constraints. This task is often completed in complex Excel® spreadsheets that are modified over time with factors applied to account for plant modifications or limitations.It is the authors’ experience that this approach is difficult to audit and replicate in a consistent manner. Furthermore, operational decisions, such as primary grind size or autoclave oxidation are made on the metallurgist or managements’ perceived optimum value and does not necessarily represent a cash flow based optimum.Many processing plants contain multiple internal constraints. As ore feed grades and properties change over the life-of-mine (LOM), processing-bottlenecks shift from one unit process to another and different operating strategies need to be adopted to maximise cash generation from the process.This paper presents a unified optimisation approach to scheduling ore based on a circuit mass balance to describe the process plant with individual models for each significant unit operation. The approach allows for optimisation over multiple input variables and the inclusion of linear and non-linear constraints.This optimisation process has been applied to different complex gold operations. The end result is an automated scheduler that selects the optimum blend of ores as well as plant operating conditions that satisfy all internal plant and shutdown constraints while maximising the objective of choice (metal production or cash flow). The models are also valuable for evaluating expansion or debottlenecking opportunities of individual processing units. These models are coded in Matlab® R2016a provided by MathWorks®, and can be deployed to end users in a compiled version with significant savings in time to run different scenarios over the Excel®-based systems.Citation:Seaman, D R, Tooher, R P and Seaman, B A, 2016. Optimisation of Complex Gold Processing Plants with Multiple Unit Operation Constraints - the Newcrest Planning Scheduler, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By F. George, W. Tice, M. Salkind

It was found that Al-A13Ni could be readily cold rolled perpendicular to but not parallel to the whiskers. Reductions of more than 98 pct were achieved without cracking by rolling perpendicular to the whiskers, whereas extensive edge cracking was noted after only 15 pct reduction when rolling parallel to the whiskers. The longitudinal and transverse tensile strengths were nearly doubled, and the longitudinal yield strength more than tripled by cold rolling 50 pct in a direction perpendicular to the whiskers. The whiskers exhibited some waviness (elastic bending) as a result of cold rolling, but at very high reductions (greater than 75 pct) whisker fracture and misalignment became significant. A fine dislocation substructure in the matrix consisting of cells attached to the whiskers was pro -duced by cold rolling. Most of- the substructure was readily removed by a 1-hr anneal at 500°C. Cold rolling was found to substantially reduce the thermal stability of the microstructure at 610°C but did not affect the stability at 500°C. FIBER and whisker reinforced composite materials promise significant improvements in properties over conventional materials. Before they find wide use, however, it will be necessary to understand the response of these highly anisotropic materials to common metalworking processes. Most of the nonmetal-lic fiber reinforced materials have very low elongations (a few pct or less) in the direction of fiber alignment. Thus, metalworking techniques such as rolling and forging would not be as broadly applicable to these materials. This investigation was initiated to determine how a composite system consisting of Al3Ni whisker reinforced aluminum responded to rolling, what changes in the microstructure occurred, and the effect of deformation on the mechanical properties. The composite material studied was produced by unidirectional solidification of the A1-Al3Ni eutectic alloy'-7 and consisted of 10 pct by volume of aligned whiskers of Alai in a matrix of aluminum. It should be pointed out that this system is not representative of all composite materials, and the results will therefore not be universally applicable. The A1-Al3Ni system is characterized by: 1) A strong fiber-matrix interfacial bond 2) A ductile matrix 3) A sufficiently low fiber content to allow significant plastic flow between fibers 4) Strong, completely elastic whiskers (tensile strength 400,000 psi, elastic modulus = 20 X 106 psi.1 These factors allow the material to be readily rolled perpendicular to the fibers. If the fiber-matrix bond were not strong, such a weak interface could fail during rolling. A measure of the ability of a composite to be rolled in the transverse direction can be obtained from noting the transverse tensile behavior. In the case of Al-Al3Ni,2 there is considerable ductility (15 to 30 pct). In the case of boron filament reinforced aluminum, for example, the transverse elongation is less than 1 pct,8 and the material could probably not be cold rolled as readily in that direction. EXPERIMENTAL PROCEDURE 3-in. diam ingots of A1-A13Ni eutectic were unidi-rectionally solidified in graphite crucibles. The starting materials consisted of 99.99+ pct pure nickel and aluminum, and the pure eutectic ingots were made with 6.2 wt pct Ni. The unidirectional solidification process (described in detail elsewhere1-3) consists of preparing a master heat of eutectic composition, remelting, and withdrawing the ingot vertically downward through the heat source at a controlled rate so that plane front solidification proceeds upward at a constant velocity. The resulting microstructure consists of 10 pct by volume of whiskers of very high aspect (length to diameter) ratio. The fiber lengths have not been measured because of the difficulty of detecting fiber ends9 but exceeds 104. There is some possibility that the fibers may be continuous within one grain. Flat sheet specimens 2¾ in. sq and approximately 0.2 in. thick containing whiskers parallel to the plane of the sheet and to one edge were used for this study. A1-A13Ni exhibits either a rod-like (high solidification rates) or a blade-like (low solidification rates) whisker morphology,1,3 and both types were studied. Rolling was accomplished using a two-high rolling mill at a speed of approximately 10 fpm. The rolling direction was either parallel to or perpendicular to the direction of growth (direction of whisker alignment). Reductions of from 0.002 to 0.03 in. per pass were used with the most common value being 0.005 in. per pass. Cold rolling of Al-Al3Ni to more than 98 pct reduction in thickness was accomplished with no intermediate anneals. In addition. a series of speci-mens was cold rolled 97 pct with a 1-hr, 500°C anneal in air after each 50 pet reduction. Tensile testing was accomplished using a Tinius-lsen four screw testing machine. Flat sheet specimens + in. wide and between 2 and 2; in. long with the thickness dependent upon rolling reduction, were used. The gage section was in. wide and 1 in. long. Strain was measured using a clip-on LVDT extensome-

Jan 1, 1970

By T. T. Campbell

Studies were conducted by the Bureau of Mines to develop a process for preparing thorium-magnesium master alloys or pure thorium metal by magnesium reduction of thorium tetrachloride in a semicontinuous reactor. Thorium tetrachloride was prepared in a fluidized-bed reactor by chlorination of thorium oxide or thorium oxalate. Conditions were established for producing a suitable thorium oxide feed for a fluidized-bed reactor. Thorium tetra-chloride was purified by vacuum sublimation and subsequently reduced by magnesium in a semicontinuous reactor to form thorium-magnesium alloys. Relatively pure thorium was produced by removing magnesium from the alloys by vacuum sublimation. Close to 100 percent of the thorium fed into the reactor was recovered either as metal (~93 percent) or as thorium oxide (~7 percent). The oxide can be recycled directly into the process.

Jan 1, 1971

By WILLIAM F. McMURRAY, James O. Lewis

The Bureau of Mines is investigating the technology of petroleum and its products, the investigation including well-drilling methods and the transportation, treatment, and utilization of petroleum and of natural gas, with especial reference to the prevention of waste and to increased efficiencyin the development of oil and gas resources in land belonging to or controlled by the Government. During. the winter of 1912-13 the enormous waste of the gas encountered while drilling for oil in the Cushing field, Oklahoma, called forth protests from various sources, and appeal was made to the President of the United States and to the Secretary of the Interior in behalf of the landowner and of the public in general. The facts were wanted regarding the amount of waste and the technical conditions that were responsible for practices causing it. An investigation was ordered and conducted under the direct supervision of the late J. A. Holmes, the first Director of the Bureau of Mines. R. S.Blatchley was sent to investigate the amount of waste going on in the Mid-Continent flelds.s In the latter part of March, 1913, J. A. Pollard and A. G. Heggem were sent to Oklahoma to study well-drilling methods with reference to the waste of gas from wells on Indian lands and to suggest means of preventing the waste of natural gas on such lands. Pollard and Heggem decided that the mud-laden fluid process, which had been used successfully for some years in Texas, Louisiana, and California was the method that would meet the situation most efficiently and economically. The method was accordingly demonstrated in Oklahoma. In 1914 Congress provided for the employment of six oil and gas inspectors to supervise oil and gas mining operations on lands of the Five Civilized Tribes in Oklahoma and to conduct investigations with a view to the prevention of waste. Positions under this appropriation have been held by William F. McMurray, James O. Lewis, Harry D. Aggers, Ralph R. "Weed,George W. McPherson, James C. Fowler, Louis W. Courtney, and Carl H. Beal, the technical work of these men being directed "byW. A. Williams, chief of the petroleum division, Bureau of Mines. After careful and impartial investigation of conditions in Oklahoma, these men also decided that the mud-laden fluid process was the one best adapted to prevent further wastes. In 1915 laws were passed by the State of Oklahoma that provide for the conservation of natural gas and oil, authority being given to the corporation commission to make rules and regulations and to employ agents to enforce them. After hearings and investigations, the corporation commission reached substantially the same conclusions as the Federal agents regarding the importance of the wastes and the best methods of conserving the gas. Technical Papers 66a and 68b were published by the Bureau of Mines in December, 1913, and January, 1914, respectively. Technical Paper 66 deals with the mud-laden fluid process in general and No. 68 with its application in Oklahoma. The interest aroused by these publications has been so widespread that within two years the first editions have been practically exhausted. Rather than reprint these publications, it has been considered advisable to replace them with the present report, which includes the results of more recent investigations. The methods of using the mud-laden fluid are an outgrowth of the rotary drilling system, which was developed in Texas and later employed in Louisiana and California. Some of the principles of the use of mud fluid had been observed and used to a limited extent for a long time in cable-tool drilling. So far as known it was first used successfully with a circulator and cable tools in the Coalinga field, California, in 1906,Harry D. Aggers, one of the contributors to this paper, working on the well. The part of the Bureau of Mines has been to call attention to its merits and to demonstrate its practical use in fields like those of the Mid-Continent.

Jan 1, 1916

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By P. -J. Kleiterp

Highwall mining is a mining method to extract coal from a final boundary in open cut mining, trench mining or contour mining. This boundary may have been reached because of economic constraints (economic strip limit) or geographic constraints (spoil heaps, rivers etc.). Coal is mined from visible, horizontal, or near horizontal coal seams by making rectangular, parallel, unsupported drives with an unmanned cutterhead and coal transport system. This is controlled from a mining unit, or launch frame, positioned outside the drive, in front of the highwall. Removal of overburden is not required or is limited to small quantities only. Highwall Mining originated in the 1940 in the Appalachian Coal Field. This paper describes the history of the various machines that have been designed for highwall mining. During the 1990 and later, there has been more emphasis on the safety in highwall mining. Many pillar strength formulae have been derived to determine the required width of pillars in highwall mining and, with that, the economic feasibility of highwall mining. The various pillar strength criteria will be discussed in this paper showing the countries where they are applied. In order to make highwall mining equipment safer and more productive, there have been quite some technological improvements applied to the machines. These technologies make highwall mining ready for the future as a serious mining method, also outside its traditional Appalachian mining area.

Jan 1, 2010

By Laurent Airaud

For around ten years, electronic detonators are available for those who want to use advanced methods and to apply theories promoted by engineers and professors to reduce blast concerns or improve fragmentation and dilution. Furthermore, decision makers can verify the use of electronic detonators to drive down mining costs. Engineers and more specifically blasters are the actual users and have to be convinced of the easiness of electronic detonators. This paper deals with electronic detonators and the notion of easiness. Common feelings about the notion of easiness are discussed. Then, examples of new technologies like, automobile, photography or Information Technology are discussed to observe how they progressed throughout time with new features and sales volume. For the specific explosive initiation industry, each step of the life of an electronic detonator is dealt with concerning the easiness and a table is used to quantify this notion.

Jan 1, 2004

By Ranajit Kumar Sahoo, Shatrughan Soren, Surendra Kumar Biswal, Soumya Sahoo, Sachida Nanda Sahu

The presence of appreciable quantity of clay mineral in Indian hematite ore needs an attrition technique using screw scrubber in the beneficiation circuit to remove the ultrafine clays and avoid downstream operational problems. Spectroscopic analysis revealed that iron ore samples obtained from the Barbil region of Odisha contain a high amount of silica and alumina in the form of clay minerals (e.g., kaolinite) contributed as a loss on ignition (LOI) in the iron-making process. Iron ore fines of below 10 mm size were subjected to a laboratory-scale screw scrubber, and the effectiveness of scrubbing as well as the pelletization of the scrubbed product was investigated. The screw scrubber in the beneficiation circuit helps to remove the clay minerals, causes an increase in iron values from 63.65% Fe(T) to 66.18%Fe(T), with improved physical (CCS of 325 kg/pellet) and metallurgical (RDI of 2.24%) pellet properties.

Aug 31, 2020

By Siavash Zamiran, Abdolreza Osouli

"One of the most concerns of room and pillar mining system is subsidence of the ground surface due to coal mining particularly in room and pillar mines. Subsidence of ground surface is a result of floor, pillar, or roof failure of the mine. At the same, due to many difficulties associated with surface disposal facilities of coal refuse, some mining companies are trying to use underground space as a disposal storage place. In this study, stability and subsidence analyses of an underground coal mine located in the Illinois Basin are conducted. This room and pillar mine was abandoned and later on was used as a storage place to accommodate the coal fine refuse with slurry backfilling method. The geological stratigrophy and geomechanical properties of the mine floor and roof were collected. Floor and pillar stability analyses were conducted for areas with various extraction ratios. The stability of the mine was evaluated both prior and after slurry backfilling. The floor and pillar stability analyses results of the mine due to moisture exposure after slurry backfilling are discussed. The subsidence potential due to mine failure is also evaluated.INTRODUCTIONA typical lithology of coal seams in the Illinois Basin consists of weak underclay stratum. The immediate weak underclay causes frequent floor instability problems in Illinois underground coal mines. There are two different stages in assessing floor stability of the mines where slurry backfilling is planned. The first stage is during the mining operation when weak underclay layer squeezes under pillar stress and results in punching or bearing capacity failure. The second stage is after slurry backfilling. During this stage, the slurry material soaks non-durable floor layers and causes strength reduction in floor material. Pillar stability conditions should also be taken into account during both the operational period and after the slurry backfilling."

Jan 1, 2015

By Sheng Zhang

The compressive strength of coal in Yanlong mine area of China is less than 3 MPa. Basically, it is powdery. The roof and floor rocks are mudstone. Therefore this coal seam is a typical ?three soft? coal seam. Roof bolting cannot be used due to the very soft strata. When the conventional U-steel support was used, roadways deformation exceeded 30% of its original dimensions in some sections one half month after development. The required repair work was huge, seriously affecting the daily mine production. This paper describes how to support the soft coal roadways. The deformation characteristics of soft coal roadway were investigated. The conventional U-steel support is not subjected to uniform load, so the whole supporting structure must be strengthened. In addition, drilling holes in the coal seam can transfer high stress from near the ribs to the deeper parts of the surrounding strata, which is beneficial to the stability of the roadway. This new support method is to combine the strengthened U-steel support with pressure-relieving drill holes, providing an economic and efficient way to support the very soft coal roadways.

Jan 1, 2013

By X. Shi, V. Vallyathan, N. S. Dalai

"Electron spin resonance (ESR) measurements show that grinding of quartz particles in air produces silicon-based (Si- and SiO-) radicals which decay with aging in air. ESR spin trapping measurements provide evidence for the generation of hydroxyl and possibly superoxide radicals from a suspension of fresh quartz particles. The hydroxyl radical generation potential of the fresh quartz particles decreases on storing in ambient air and on the addition of catalase, superoxide dismutase, desferoxamine, or DMSO. Silica-induced lipid peroxidation also decreases on storing the fresh particles in ambient air. These findings suggest that oxygenated radicals play a role in the biochemical mechanism of pneumoconiosis in general and acute silicosis in particular.INTRODUCTIONThis communication summarizes our electron spin resonance (ESR) investigation of the formation of oxygenated radicals by freshly crushed quartz particles in a cell-free aqueous medium, and its potential role in the biochemical mechanism of acute silicosis. This study was undertaken because the mechanisms by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood. 1-3 It is generally believed, however, that the action of quartz particles on the cell membrane is the starting point of the silicotic process. 1,4 Since the first step must involve surface reactions, characterization of the chemical structure of the surface of quartz particles has been the subject of several recent studies!-' For example, we reported that mechanical crushing of quartz under normal atmosphere generates silicon-based (Si• and SiO•) radicals which decay with time, and that these radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to that of an aged dust from the same stock. 6,8 Independently Fubini and coworkers' have also reported on the formation of Si• and SiO• -type of radicals from quartz particles crushed under atmospheric conditions. Gulumian and van Wyk9 have reported that quartz particles react with hydrogen peroxide (H202) to generate hydroxyl (•OH) radicals. These authors9 suggested that this process might contribute to quartz's pathogenicity but the mechanism of the -OH radical formation was not clarified. Earlier, Gabor and Anca10 had suggested that the cytotoxicity of quartz particles might be associated with the generation of some factor or factors possessing the properties of a free radical and hence capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently, Weitzman and Graceffa 11 reported that asbestos is able to catalyze the generation of -OH radicals from H2O2. Their later work12 indicated that lipid peroxidation might be one of the mechanisms of tissue injury by asbestos."

Jan 1, 1989

By C. W. Vierrether

Mineralogical analysis contributes directly to the selection of applicable beneficiation techniques for a given site. Tentative remediation methods for use on the Sharon Steel tailings in Midvale, Salt lake County, UT, were determined in part by mineralogical characterization. A systematic characterization scheme was employed to identify mineral species, mineral associations, and grain size. This paper presents the mineral content and distribution data collected for site characterization. This data was used to determine areas that were representative of the total tailings at the Sharon Steel site. Although this was the main focus of characterization, other useful information was obtained. The approximate location of "old jig tails" was identified and insight on possible arsenic, mobility through the pile was also obtained from the mineralogical study.

Jan 1, 1991

By G. Mei

"This study explores froth flotation and selective flocculation methods to recycle waste phosphors containing several rare earth elements, namely, yttrium (Y), europium (Eu), cerium (Ce) and terbium (Tb). The effects of the presence or absence of collector and of flocculant and their dosages, as well as the pH, were investigated. Reverse flotation resulted in concentrates with grade of 27.03 percent and recovery rate of 71.36 percent, while flocculation resulted in concentrates with grade of 31.43 percent and recovery rate of 91.28 percent. The flotation and flocculation behaviors were further analyzed by X-ray diffraction analysis, zeta potential measurements, particle size distribution and other methods. The successful separation of rare earth minerals by flotation was attributed to the selective adsorption of the collector onto quartz, making it particularly recoverable by reverse flotation so as to be separated from the valuable materials. The analysis of the particle aggregation process indicated that its better flocculation performance was due to the selective adsorption of flocculants onto the unwanted materials, enlarging the flocculant sizes by forming aggregations and facilitating the separation of rare earth minerals from waste materials based on different settling rates. IntroductionBecause waste phosphors pose the problems of heavy environmental burden and high risk to human health (Hu and Cheng, 2012) as a result of containing heavy metals such as mercury and manganese (He et al., 2006; Lucas and Emery, 2006), they have received added attention as urban mining resources for extracting rare earth elements (REEs) like yttrium (Y), europium (Eu), cerium (Ce) and terbium (Tb).At present, chemical processes such as acid leaching, alkali fusion, roasting and extraction are the primary methods for recovering REEs from waste phosphors (De Michelis et al., 2011; Li et al., 2012; Li, 2010). With these strategies, phosphors can be effectively decomposed and their REEs extracted. After the removal of impurities, the REEs can be efficiently precipitated by adding an H2C2O4 solution (Porob et al., 2012). Although relatively high recovery rates are achieved, those processes entail high energy consumption and can cause severe environmental pollution."

Jan 1, 2017