Search Documents

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022

By D Veneziano, J Van Dyck, R Snow, W Pytel, O Zanoli

Best practice standards generally recommend assessment of the environmental and societal risks posed by tailings storage facilities, but they rarely specify how the analysis should be made. As a case study, this paper describes a safety assessment of the Zelazny Most tailings pond operated by the Hydrotechnical Unit of KGHM Polska Miedz SA in Poland. The complete assessment includes a failure mode effect criticality analysis (FMECA) that considers all conceivable failure modes, but this paper focuses on one key mode, the loss of stability during the planned raising of the crest above its current level. Reliability against static dam failure considers uncertainty on the safety factor in a limit equilibrium approach. The threat of dynamic (earthquake induced) instability is assessed by developing a model of future seismicity as a function of the mining plan and considering uncertainty on the induced permanent displacements along critical sliding surfaces. We quantify the additional level of protection against outflow provided by the beach using an event tree with expert-assigned probabilities. Continuous monitoring of the dam for premonitory signs of instability and a set of loss-prevention plans in the case of a spill provide additional layers of protection; their effectiveness is quantified by estimating the fraction of the population that could be evacuated as a function of warning time. The probabilistic analysis indicates that the safety targets are met and produces practical recommendations on how to maintain and improve the safety level while the dam crest is raised above its current level.CITATION:Van Dyck, J, Pytel, W, Veneziano, D, Snow, R and Zanoli, O, 2015. Safety of a tailings storage facility against dam instability, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 253–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Khosrowshahi, A Weeks, W J. Shaw

"To provide an indication of expected performance of the mine and mill, feasibility studies should include an assessment of the expected day-to-day variability in process plant feed. Attempts to do this based on conventional resource models will be flawed as such studies fail to consider and account for the in-built smoothing (averaging) of input data.This can lead to one of two situations: an expensive, over-engineered process plant that can cope with every possible situation, or operational strategies that fail to manage the natural variability within the orebody and the impact of day-to-day operational decision-making.In both cases the value of the project diminishes through excessive capital costs or reduced throughput or recovery during operations.Unlike conventional estimation techniques, the geostatistical method of conditional simulation can reproduce the inherent variability of the deposit. Once a valid model has been developed, it is possible to analyse the model using a transfer function that simulates the proposed mining processes and provides a representation of the likely variation of mill feed characteristics at any time scale.The case study demonstrates how the proposed mining strategy would result in mill feed being considerably more variable than expected, resulting in poor recovery, low throughput and potential breaches of environmental conditions. Mitigation measures included budgeting for additional mining equipment to enable greater flexibility during mining and revised stockpiling and crusher feed strategies.Awareness of the benefits of modelling the variability of geometallurgical parameters will increase the use of this approach in producing more realistic financial models of expected mine performance at the design stage.CITATION:Shaw, W J, Khosrowshahi, S and Weeks, A, 2013. Modelling geometallurgical variability - a case study in managing risk, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 247-252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By S. Rajan

Familiarity with NEMA standards and the influence of the power supply on the motor-load system permits the user to make the necessary decision as to whether a standard or special motor is needed for his particular application. This paper highlights the more important aspects of NEMA standards for ac induction motors from the application engineer's standpoint and the effect of the power supply on motor characteristics.

Jan 1, 1975

By R. Sharon, P. M. Hawley, X. Ochoa

"Development of Barrick Gold’s Pierina gold mine in north-central Peru requires construction of a waste dump for disposal of nonore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low-quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high-quality, hard, durable, blocky waste rock.A hybrid dump design concept was developed that requires in-pit segregation of highand low-quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included.This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems."

Jan 1, 2003

"The first SkimAir flash flotation cell was installed in Outokumpu’s Hammaslahti Copper Concentrator in 1982 to prevent overgrinding of soft sulphides in the milling circuit. Since this first installation the popularity of the flash flotation has fluctuated depending on metal market conditions and regional preferences. Units have been installed in many commodities including copper, lead, gold, PGMs, silver and nickel. Though it has been successfully employed in many operations around the world, flash flotation technology is still not well understood by many in the mining industry. This paper will discuss aspects of flash flotation flowsheet development along with some of the metallurgical and engineering considerations required to successfully incorporate flash flotation into new or existing milling circuits. This paper will also try and debunk some of the myths that exist around flash flotation cells and their operation. Case studies of flash flotation implementation will be discussed.IntroductionModern flash flotation technology was developed several decades ago by Outokumpu, with the first commercial installation of this technology being at the Hammaslahti concentrator in Finland in 1982 (Kallioinen & Niitti, 1985). This was a relatively modestly sized SK80 cell producing final grade copper concentrate directly from the flash flotation cell operating in the grinding circuit. Since that time the size and number of flash flotation cells installed globally has grown considerably to the point where today, it is a widely known application of flotation technology for amenable ores. Owing to their long history in developing the technology, Outotec are the market leader with their SkimAir range of flash flotation cells. Though there is a general awareness of flash flotation process in the mineral processing industry, there is a lack of detailed understanding of the process and the benefits it can provide to new and existing operations."

Jan 1, 2017

By John S. Newton

Modern high capacity underground mining machinery is a complex of mechanical, electrical and hydraulic components which have greatly increased capability over similar components of mining machinery of ten and. even five years ago. Looking into the future I feel certain in stating that there will be changes equally great in the coming five and ten year periods. With this premise in mind, I should like to bring to your attention some of the things that do and will have a continued major impact on the industry, particularly as they relate to the maintenance and operation of these machines of increasing capability. In underground mining today, nearly every individual plays a key role. A machine operator's importance in his work is comparable with that of the pilot of an airplane, a railroad engineman, a bus driver, a skilled machinist, a bulldozer operator and many others whose assignment is one of doing, by himself, with his hands and his brains all that the specially designed machine has been created to do. These machine operators are supported by a staff of skilled engineers, maintenance personnel, supervision, etc., but objectives are realized only when the operator maintains his schedule. What is being done and what can be done to make it easier for the operator to maintain his schedule which, as with the airplane, is constantly being improved? This question can be answered best, perhaps, by dividing the subject into four general categories - (A) Power Supply. (B) Control and Protective Devices. (C) Hydraulic Component Design. (D) Mechanical Design.

Jan 1, 1962

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.'-' Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,'8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By John H. Harden

In the valuable paper of Mr. Dunbar D. Scott and its varied discussion, on the evolution of mine-surveying instruments, the tripod-head has not received the attention it merits. During the last 50 years this very necessary adjunct to the surveyor's instrument has been much improved. The legs are of better construction; and the devices for laterally moving the instrument over the station-point and for quick leveling, without the use of the screws, have given to the instrument fitted with the modern tripod-head the same facilities possessed by the oldfashioned ball-and-socket, with more perfect accuracy, not attainable in the latter, while saving from 30 to 50 per cent. of the time required for setting the instrument over a station. For the purpose of extending the discussion to this import-

Jan 1, 1902

By Denis Shishin

The pyrometallurgical production and recycling of non-ferrous metals involves the use of complex feed stocks, having awide range of chemical compositions from sources that include mineral sulphide concentrates, high value obsolete materials and process wastes. The commercial viabilities of these operations hinge on the ability to extract value from these materials. Increasingly, modern computer-based tools are used to describe and predict process outcomes, including mass and heat balances, the partitioning of elements and phase equilibria. At the heart of these predictive tools are thermodynamic databases that describe the fundamental chemical properties of a system and all the components present. A comprehensive research program has been established to develop an accurate, self-consistent thermodynamic database describing all gas-slag-matte-metal-speiss-solid phases in the system Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Sb-Sn-Ag-Au). The database can be used in conjunction with the FactSage computer platform. The accuracy of the database and its application to industrial practice is demonstrated.

By Charles A. Ashburner

' I. Natural-Gas Explorations. The rapid development of the natural-gas* industry in Western Pennsylvania, and the great economy which results from its use, both for manufacturing and domestic purposes, has led to an inquiry as to the occurrence of this gaseous mineral in all thickly populated and large manufacturing centers of the United States. Natural-gas springs are to be found in almost every State in the Union, and in many States gas has been obtained in wells sunk either for water, oil, or gas, or in search of solid mineral deposits. The occurrence of natural gas is, however, not dependent upon mere chance, as is popularly supposed, but upon the existence of special geological phenomena; this fact is now recognized by professional men and by many practical men concerned either in the exploration for or in the use of this gas. The desire among our leading manufacturers, to emulate Pittsburgh, has led to the sinking of many wells in many localities, in search of natural gas. Some of these wells are now being located and drilled under the direction of professional experts, but many more have been, and are still being located by "quack " explorers, who often depend upon spiritualistic communications, or the diviningrod, or by intelligent persons, who are ignorant, however, of the geological and physical conditions under which gas has already been found. My attention has recently been directed to a number of these exploring operations where holes have been drilled, and, after failing

Jan 1, 1887

By Marcel Vallée

Abstract -Traditionally, samples collected for mineral deposit evaluation have been viewed without explicit reference to reliability, with the illusion that a true value is attainable from a few samples and verifications. For exploration, mineral deposit estimation and production quality control the following definition is proposed: "a sample is a small quantity of material relative to the geological mass it represents, collected according to a systematic procedure, of measurable reliability, from which the grade/quality of the mass which it represents may be estimated, based upon appropriate protocols. This paper will concentrate on the actual rock sampling process. Too often, sample size has been, and is still viewed as a matter of convenience, leaving out representivity considerations, despite the importance of samples on project estimation. Linear samples (chips, channels, drill), panel samples, broken rock or mining samples and very large samples are considered. Collection procedures and quality control protocols to improve the representivity of non-mechanical samples are proposed.

Jan 1, 1998

By J. B. Scott, J. S. Nelson, G. H. Kruse, W. S. Johnson, K. L. Zerneke

The economics of pressure tunnel design emphasize the utmost utilization of the least expensive pressure-resisting material available, namely, the rock surrounding the tunnel. A major difficulty in the design is the problem of transferring internal hydraulic pressure to the rock through a tunnel lining or membrane provided to maintain watertight conditions. The lining is necessary not only to prevent water loss, but to prevent the diffusion of water at high pressure through joints and fractures beyond the confines of the tunnel, an occurrence which could ultimately affect the stability of the rock mass through which the tunnel passes. Because of its toughness and ability to bridge localized areas of weakness, steel is used for a lining material whenever high internal pressures are involved. The steel lining is coupled to the surrounding rock mass through an annular ring of concrete backfill. It is paradoxical that the steel lining, needed primarily to assure water tightness, must of necessity be incorporated into the structure as a major pressure-resisting component, not to augment the bearing capacity of the concrete and rock, but to limit the strain for the safety and preservation of the steel lining itself. With the deformation modulus of the steel so much greater than that of the rock, the liner approaches its yield strength before the load capacity of the rock can be fully mobilized. An economical determination of plate thickness for steel liners is therefore dependent upon measurement of the properties of the surround-

Jan 1, 1970

By Verne E. Hooker

In situ stresses, based on isotropic and anisotropic relations, were evaluated using computer techniques from overcoring data obtained in dimension stone quarries along the Appalachian Piedmont, the Ozark Uplift, and the Ouachita Tectonic Belt. Stresses in the horizontal plane near the surface are compressive and range from 100 to 4,500 psi. The direction of maximum compressive stress seems to be alined with the general tectonic structure for most of the determinations. The ratio of the maximum to minimum elastic parameters in the horizontal plane ranges from 1.05 to 2.46 for these competent rocks. Isotropic versus anisotropic stress determinations show differences only as great as 25 percent in stress magnitude and 25° in orientation.

Jan 1, 1969

By Warwick D. Bullen

Gold mining in the Yellowknife area of the Northwest Territories started long before the concept of sustainability entered the academic literature and by the time the term enjoyed widespread public acceptance, the Yellowknife gold mining industry was in its sunset years. Nevertheless, the city of Yellowknife will long outlive the gold mines that it was founded on, demonstrating that not only can mining build sustainable communities, but that sustainable mining as a concept is an entirely valid precept. To this effect, the authors examine the complex economic and social aspects of the gold mining industry in the Yellowknife area over the last 70 years.

May 1, 2004

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.