Search Documents

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production, but the thermal state of pellets in the drying section is still unclear. In this study, the temperature distribution of the drying section was investigated using computational fluid dynamics (CFD). The results indicate there is a coupling effect in the drying section of a traveling grate. Gas with higher temperature in down-draught drying (DDD) transfers heat to the up-draught drying (UDD) through the gap of the insulation board, and the temperature gradient of the pellet bed changes before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD are displayed in UDD in advance. To verify the model, a contrast experiment was conducted.

By D. A. Ponniah

The installation of a pile is considered analogous to the expansion of a cylindrical cavity of a diameter equal to that of the pile. Using Vesic's theory of the expansion of cavities the effect of soil properties on pile installation loads, radial pore and total pressures are evaluated. The theoretical results are compared with load and pressure measurements made in field trials in a stiff clayey glacial till in the U.K.

Jan 1, 1987

By D. R. Schmitt, N. Ong, R. S. Kofman

Shales and mudstones comprise about 75% of all the sedimentary rocks. In, particular, organic rich shales are considered as a petroleum source rock and more recently with the advent of hydraulic fracturing technology to be a reservoir in their own right. In this sense, the aforesaid motivates our work with laboratory measurements of elastic properties of these geologic materials, which are known to be anisotropic. As such, assuming Vertical Transverse Isotropy (VTI) symmetry, the dynamic and static moduli of a series of cores from various geological formations in Alberta, Canada are simultaneously investigated as a function of confining pressure using the ultrasonic pulse transmission method and strain gages. Dynamic moduli were obtained from ultrasonic P- and S-wave velocities measured on a prism cut with faces perpendicular, parallel and oblique to the assumed vertical axis of symmetry. Static moduli were calculated from strain-stress curves obtained along the directions perpendicular and parallel to the assumed axis of symmetry as well. Velocity measurements show that samples are highly anisotropic, but that the pressure-dependent behaviour of the wave speeds differs. VP(90°) and VSH(90°) both with layer parallel propagation and polarizations change little with pressure while VP(0°) and VS(0°) (both with layer perpendicular propagation) display significant nonlinear responses particularly at pressures < 25 MPa. These characters transfer to the derived full set of elastic constants. In order to effect a proper comparison of the dynamic and static moduli, we convert the dynamic elastic constanst to linear compressibilities pependicular (Kdyn1) and parallel (Kdyn3) which are directly comparable to the static tangent compressibiities obtained by differentiation of the observed strains. Both sets highlight the anisotorpic nature of the material but most interestingly Kdyn1 _ Ksta1 but Kdyn3 > Ksta3 by nearly 40% for one of the samples. The other samples measured respond similarly suggesting that conceptually the structure of such materials could be considered to be constructed of alternating stiff or compliant layers. This finding has implications in the response of the formation to stress particularly during hydraulic fracturing and the interpreation of acoustic logs in providing appropriate measures of elastic properties for engineering purposes.

Jan 1, 2015

By J. L. Post

A large body of readily available Na-montmorillonite is present about 24km (15 miles) east of Fallon, Nevada. The clay is comparable to Wyoming Na-bentonite, but with somewhat less MgO and somewhat more Fe2O3 in its crystal structure. The physical and industrial properties of the Nevada clay are comparable to those of the Wyoming clay. The Na-montmorillonite is presently mined for use as hazardous waste barrier material and as a sealant for canals. It may be economically feasible to process the clay material for removal of impurities.

Jan 1, 1996

By E J. Hofmann, J E. Hofmann, A J. Hofmann-Fritz

"With its Head Quarters in Perth, global heavy engineering company Hofmann Engineering is one of the largest family owned engineering companies in Australia. The company has pioneered a number of new manufacturing processes and design improvements for components of large comminution equipment.Some of these innovations are: Innovative design improvements of high pressure grinding roll (HPGR) forged steel tyres. Hofmann Engineering has developed unique patented tungsten carbide stud and edge protection designs which improve wear life and introduce quick and cost effective replacement options to further extend the life of the tyre. Development of forged fabricated mill heads using rolled and welded high tensile steel plate as an alternative to cast conical mill heads. Establishment of Australian capability to manufacture and export up to 42 ft. (12.8 m) diameter SAG mill shells. Techniques for fast track, product improved replacements of cracked or damaged mill gears, including in situ profile &amp; wear measurements of girth gears using portable coordinate measuring machine (CMM) technology, forged rim steel and induction hardening technology. Gear and pinion mechanical drive designs to 24 MW or higher for SAG mills of 38 ft. to 42 ft. (11.6 m - 12.8 m) diameter as reliable alternatives to gearless drives.The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering on large, high powered equipment for both the domestic and export markets.CITATION:Hofmann, E J, Hofmann, J E and Hofmann-Fritz, A J, 2013. Australian innovations in high pressure grinding rolls and large grinding mill manufacture, in Proceedings MetPlant 2013, pp 141-151 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By W. E. Bawden

Situation: Creighton mine, situated about twelve miles west of Sudbury, Ont., on the Algoma Eastern railway, is owned and operated by the International Nickel Company, incorporated in the United States under the laws of New Jersey. The ore is smelted at Copper Cliff, near Sudbury, and the matte is refined at Port Colborne, Ont., on lake Erie. Geology: The ore occurs in what is known locally as &apos;the basin&apos; near Sudbury (Figure 1) the central part of which is composed of the Animikie series of sediments, consisting of sandstones, slates, tuffs and conglomerates. The basin is about 16 miles wide and 36 miles long. The Animikie sediments are surrounded by a sill of norite - a gabbro rock in which the pyroxenes are orthorombic. On the outer contact of this norite the sulphide deposits occur and the Creighton deposit, similar to others, lies on the southern edge of this basin. There are two orebodies at the Creighton, the upper one called the footwall orebôdy, and the lower one the hanging-wall orebody. The hanging-wall of both of these bodies is norite, and the footwall of the upper one is granite. The two are separated by an intrusion of greenstone which forms the footwall of the lower body. The ? maximum length of the deposit is 1000 feet and the maximum width is approximately 300 feet. It narrows at the ends and is somewhat lenticular in shape. The dip is about 45 o to the west, and the strike is north and south. The orè is a mixture of three minerals - pyrrhotite, chalcopyrite and pentlandite. The pentlandite, which is distinguished by its cleavage from the other two, is apparent to the naked eye only in the lower orebody and is more finely disseminated in the upper one. The lower body contains a little higher percentage of nickel.

Jan 1, 1925

By R. D. Leitch, W. P. Yant, A. C. Fieldner, R. R. Sayers, S. J. Pearce

"The detection of leakage is a recognized problem in the safe and economic distribution and use of natural gas. Natural gas is practically odorless and therefore lacks he property of indicating significant leakage by the sense of smell, the means most widely used by gas employees and consumers for detecting leaks of the more odorous types of fuel eases. In view of the recognized value of the odor of gas for indicating leakage at the time of occurrence the Bureau of Mines has studied' the possibility of adding small amounts highly odorous substances to types of fuel gas (such as blue water gas and natural gas) that lack warning properties. These studies revealed that the mercaptans were promising substances to accomplish this purpose, not only for odorizing fuel gases but for other purposes° where it was desired to give warning through the sense of smell.Since completing the studies mentioned, the Bureau of Mines jointly with the American Gas Association has conducted further investigations dealing with the use of warning agents for fuel gases. The results of this work will be published later.The Bureau of Mines had been desirous of observing the practical use of ethyl mercaptan for detecting leakage of natural gas, particularly to determine whether the odor would permeate the ground and give indication of lea's in underground pipes. Opportunity for making these observations was recently given by E. A. Munyan, manager, gas department, Union Gas t Electric Co., who requested the bureau's cooperation in making leakage surveys of the company's distributing systems at Franklin and Middletown, Ohio."

Jun 1, 1930

By C M. MacRae

The characterisation of high-P iron ores by field emission gun electron probe microanalyser (FEGEPMA) was carried out to determine elemental associations in iron oxides sensus lato and, using this knowledge, to speculate on possible P incorporation mechanisms in goethite. Quantitative data was collected from two goethite-rich bulk ores and results showed that in both samples goethite was the main repository for phosphorus. The P-rich goethite also contained elevated levels of both aluminium and silicon.To understand the mechanism of P incorporation in goethite, high-P grains were located by coarse mapping of polished blocks with the FEG-EPMA. Analysis of element distribution maps collected on the P-rich grains showed that low-P regions within grains were typically associated with low-Al and high-Si, whereas high-P regions were associated with high-Al and low-Si. Based on follow-up quantitative analyses, a coupled substitution mechanism for phosphorus incorporation within goethite was proposed: 2Si4+ = 1P5+ + 1Al3+. Additional quantitative analyses on further examples indicated the mechanism was only valid for Si contents in goethite of &lt;1 wt per cent.Preliminary transmission electron microscope (TEM) studies confirmed the presence of P, Al and Si in goethite.

Jul 11, 2011

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

By M. M. Fine

This report presents the results of laboratory mineral-dressing investigations by the Bureau of Mines of 14 individual or composite character samples from deposits in the Batesville manganese district. It will be noted that some concentrates have met or approached analytical specifications for metallurgical manganese ore although great variations in both physical and chemical composition from once deposit to another make each a new problem. In most cases it is evident that a substantial loss of manganese has occurred in the various slime and tailing products. An important aspect of this work is the research being conducted on manganese-bearing limestones. Recent reconnaissance indicates that this resource constitutes one of the major domestic reserves of manganese. Laboratory study has shown that ferrograde concentrates can be recovered from samples of manganese-bearing limestones from two properties. Research on samples from other areas is still underway.

Jan 1, 1957

By Leo A. Schrider

A prediction for oil recovery from a pilot waterflood in the Kane oil- field, located in Elk, Forest, and McKean Counties, Pa., was made and compared to actual field performance. Water-injection and production histories, well logs, other field data, and results from laboratory tests of core material were used in this analysis. Performance of the pilot waterflood, initiated in January 1963, was predicted using a modified Craig, Geffen, and Morse calculation technique. Maximum recovery from this low permeable, preferentially oil-wet formation was predicted to be about 22,500 barrels of oil after 300,000 barrels of water had been injected into the pilot waterflood area. After additional field data were collected it became necessary to reevaluate the pilot waterflood area. The gas saturation prior to the waterflood was estimated to have been 20 percent, based on an assumption regarding the required volume of water injected to initiate oil production. In view of the actual field performance, a gas saturation of 13 percent is indicated. When this gas saturation and the method originally proposed by Craig and others are used) the predicted results are more representative. In December 1965, field performance was further analyzed using a hyperbolic-decline curve as presented by Arps. Based upon this evaluation method, the pilot water flood in the Kane sand should produce 37,000 to 42,000 barrels of oil with the injection of 300,000 barrels of water into the pattern. By continuing this secondary-recovery project to a reasonable economic limit, ultimate oil recovery may be as much as 50,000 to 55,000 barrels, or 129 to 142 barrels per acre-foot from 36.5 acres.

Jan 1, 1967

By Raju S. Sagi

This paper deals primarily with the different types of drilling methods used by the Iron. Ore Company of Canada for sampling the soft and friable hematite-limonite (secondary) iron ore deposits found in the Scheferville area. The problems associated with drilling, sampling, sample handling and sample preparation. for chemical analysis of these ores are discussed. Systematic evaluation of the various drilling methods led to the selection of an integrated drilling system. This system consists of a rotary dual- tube - reverse-circulation drill, with tricone bit, polymer mud and mechanical sample splitter, The historic al development of this drilling system is described in detail, as are the equipment , sample flow and quality control checks carried out to obtain representative samples. This integrated drilling and sampling system has been used satisfactorily on a routine basis for determining the grade and tonnage of ore for the various deposits for the last five years (1972-76) in the Schefferville area.

Jan 1, 1977

By R. K. Mehta

An accurate, efficient and stable computation of the mill matrix function (eAt) is needed where mill matrix (A) is a real general matrix. Two important modeling cases in comminution where such need arises are: Heterogeneous comminution behavior of multi-component ores and ultra-fine grinding involving simultaneous attrition and fragmentation breakages. This paper presents the application of a novel splitting method in conjunction With similarity transformation technique in the form of "product formula" which is found to work in all cases and uses a most aggravating, yet interesting property of the matrix exponential in a restricted sense. Results are presented showing that this method can yield solution as accurate as those obtained With an analytical technique. The utility of this computational approach is demonstrated by parameter estimation analysis using a distributed component model in the liberation area through computer simulations.

Jan 1, 1992

A series of electron beam, cold hearth, single melt Ti-6Al-4V plates (nominally 2.5 cm thick) impacted by 2cm diameter, 4340 steel projectiles (with 54g nominal mass) at velocities ranging from 0.633 to 1.027 km/s were sectioned along the impact axis and examined by optical metallography to characterize the formation, growth, and microstructure of adiabatic shear bands. Near ballistic limit velocities, the shear bands propagate towards the rear of the target where they coalesce and grow to provide a cylindrical solid state flow regime for the plug volume.

Jan 1, 2006

By Edward J. McNamara

Sulphur as an element has been used for centuries. The technique of storing, handling and transporting it in its various forms has changed through the years. Freeport Sulphur Company, a division of Freeport Minerals Company, has produced sulphur since 1912. The first storing and transporting of this product as a liquid began in 1947. Significant environmental problems occurred in the handling of solid sulphur in the late fifties and early sixties. Since the sulphur WAS produced in the liquid form and the major customers used it in the liquid form, it became obvious that a liquid transportation system was the solution. The liquid sulphur delivery eliminated the dusty and hazardous handling problems and the contamination of the sulphur by dirt, acid, moisture and other materials. The remelting by the customer to use the sulphur is thusly eliminated with a savings in energy. In addition, this change in the mode of handling permitted a broad development of new sulphur mines in the marshy coastal area of Louisiana and offshore in the Gulf of Mexico.

Jan 1, 1978

By V. V. Khristenko, V. I. Dubodelov, V. A. Seredenko, B. A. Kyryyevsky, H. V. Seredenko

"During the last decades investigators of many countries shows an increased interest to alloys which are characterized by miscibility gap in a liquid state. It is connected with essential possibilities of control of structurization in such alloys because of the melt at certain temperature parameters is · emulsion with disperse phase inclusions. These ensure essential influence ·on structurizations.The certain inclusions can play a role of lubrication ensuring ""wearless"" process. The sizes of inclusions of this phase can be rather large proportional to sizes of strengthening phase (up to 1000 nm). Other inclusions ensure process of strengthening of a main material. In this case requests to a dispersibility character of distribution and structure of such inclusions are much higher.The multicomponent alloys of system of copper - (Fe - Cr - C)- alloy concern to the number of advanced compositions. The copper alloys with structure of a type of a ""frozen emulsion"" in which strengthening phase· is a chromium pig-iron are characterized by high thermal stability in the extreme operating conditions. The mechanism of inclusions forming is emulsifying of a melt in miscibility gap at temperatures close to temperature of binodal under superimposition of external effects.The main complexity of producing of ware from such alloys is .a providing in their structure of necessary dispersible inclusions uniformly distributed all over the volume. Thanks to a selective action of electromagnetic fields on liquid phases with various electroconductivity relative velocity of phases is created and is regulated the ratio of their ""apparent"" specific gravity is changed. Excitation of pulsing force effects with the certain frequency on interphase surface allow actively to influence on process of a dispersion of a liquid metal medium."

Jan 1, 2000

By Harold V. Pearce

THE plant of the Boston and Colorado Smelting Company, at Argo, Colo., has not received special notice in technical or scientific publications for some time past. Dr. Peters&apos; described the development of the reverberatory furnace used at Argo, but he dealt almost exclusively with the increase in size and the corresponding gain in capacity. Since the time of his description the changed conditions have led to a modification of the former smelting practice, and this modification forms the basis of the present paper. No claim is made for personal originality in connection with these improvements, in fact, I expressly disclaim any such intention, since nearly every successful step in the development of the process now used at Argo has been suggested by Dr. Richard Pearce at various times during the past 12 years, though perhaps in a different manner of exe¬cution. These changes would undoubtedly have been made before, were it not that many problems of greater metallurgical importance and momentarily of more urgent need thus had to be solved. At the time to which I refer, economic conditions demanded mainly an increase of capacity. Moreover, the determination and placing of exact losses in smelting were not so imperative as they now are. About three years ago, the time of my appointment to the - management of. the works of the Boston and Colorado Smelting Co., the great decline in the price of copper occurred; the Argo plant, in common with all others engaged in the copper-industry, lost heavily in the market-value of the stocks on hand of ore and furnace-products. Added to this was the unfortunate circumstance that the copper-supply of the Argo plant from general sources began to dwindle; in fact, it almost entirely ceased. About this time the smelting-plants in the west-

Mar 1, 1905

By Christian O’Keefe, Alex Van der Spek

"Evaluation of inequalities of the partial sums defining cumulative grade and recovery prove that cumulative grade has an upper bound not dependent on the bank number and cumulative recovery possesses an upper bound proportional to the bank number. This explains one observed characteristic of cumulative grade versus cumulative recovery curves. The existence of such maxima combined with the observed shape of cumulative grade-recovery curves leads us to postulate that these curves can be well described by rectangular hyperbolae. Rectangular hyperbolae are characterized by asymptotes at right angles to each other. It is proven that this property can be used to derive an equation for the cumulative mass flow of the concentrate in terms of the asymptotic values of cumulative grade and cumulative recovery. Fitting hyperbolae to experimental cumulative grade cumulative recovery plant data then results in estimates of the maximum grade, the maximum recovery and a constant which may be taken as a performance coefficient of a row. Normalization of the cumulative grade and the cumulative recovery by their respective maxima gives rise to a graphical representation that can be used to evaluate the operating performance of a row of floatation bank cells. The normalization procedure removes the bias that is introduced by inevitable variation in mass flow of the feed and variation in feed mineralogy or feed particle size distribution. Reduction of the normalized data collapses all cumulative grade-recovery data onto one and the same curve. This removes the differences caused by the variation in row performance. The reduced cumulative grade-recovery data scatters around a common hyperbola. This can be used to gauge the validity of the assumptions made. Normalized cumulative mass pull is determined from the fitted values of the maximum recovery and maximum grade. This may serve as an alternative performance indicator of the floatation row."

Jan 1, 2014

By H. W. Gillett, E. L. Mack

"This report describes the trend of developments in electric brass-furnace practice in the last two years, and supplements Bureau of Mines Bulletin 202, ""Electric Brass-Furnace Practice"", which was published in 1922. In that bulletin it -as pointed out that some of the lines on which electric brass-furnace progress would take place were clear, but others were less so.Developments in foreign countries.Foreign brass-melters have not yet adopted electric melting to an extent comparable to its use in the United States. It is doubtful Whether all foreign countries combined use 100 electric brass furnaces; of these about 35 are of American make (Ajax, Detroit, Baily) and are operating in Canada, Mexico, England, France, Japan, Sweden, Switzerland, Spain, Norway, Germany, Argentina and Czecho-Slovakia.`The Rennerfelt furnace finds some use in Sweden (1)c, notwithstanding its high metal loss on alloys high in zinc, Two German firms are reported(2) to be using the Rochling-Rodenhauser induction furnace on bronze, the average energy consumption being given as 400 kw.-h. per ton. No comment is made on any trouble from the ""pinch effect"", A firm in Switzerland is reported (3) to use three 600-lb., direct-arc furnaces of its own design to melt babbitt, antimonial lead, coinage silver, nickel, copper, and brass. The metal loss on yellow-brass turnings is high. Use Of a direct-arc furnace in England, with precautions aimed to prevent surface overheating, vas abandoned (4) in favor of an Ajax furnace."

Apr 1, 1924

By Paul B. Batten

Shutdown is a generic term for what may be called an Outage, Turn Around (TAR) or Overhaul etc. Running a plant shutdown well has always been key to the financial contribution of a mine. However, something important has changed. The post pandemic reality is that it is harder to retain workers and many of those near retirement just didn’t come back to work. This is creating a shortage of experienced people and a workforce that changes employers easily. We are seeing the impact of this manifested in the erosion of established maintenance and supply chain processes that now struggle to yield the plant runtime that could once be taken for granted. The scope, cost and duration of a shutdown varies widely depending on the nature of the work and the equipment being renewed. The PM of an electric shovel might require a week of downtime and cost $100,000. A gold plant may need to go down for 3 days when its time to change mill liners and cost $500,000. A turnaround in a refinery can take more than a month and cost multi millions. Despite the huge differences.

Jan 1, 2023