Search Documents

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By Mehmet Guney

Acceptable working environments in production areas and service openings of Mindola Mine on the Zambian Copperbelt are currently maintained with an air volume of 1000 cu m/s and 5500 kW of installed refrigeration plant. It is planned to open up additional deeper areas of the mine for future production. Temperature problems, due to the increased heat generation from various underground sources are recognized as potential hinderances to efficient production. Findings of research work indicate that the present total heat output of 58,000 kW will inevitably increase by the second five-year period of the deepening program to 52,900 kW and by the fifth five-year period to 63,200 k\V. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 53.8/40.2 °C and 35.5/42.1 °C respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 k\V This paper deals with the thermal problems in Mindola Mine, current heat output calculations, future prediction of temperature and heat load in various working areas of the mine with the application of computer programs and interpretation of data in order to find the effective solution for long-term planning of ventilation and air-conditioning.

Jan 1, 1982

By Ralph H. Nafziger

The Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory, has electroslag melted a V-5Ti-5Cr alloy using a fused CaF2, flux. The alloy is a candidate for use in future fusion reactors. One objective of this research was to evaluate the feasibility of the electroslag melting process in separating simulated radioactive isotopes from the V alloy to demonstrate recyclability. Small amounts of Ca, Y, and Mn were added as surrogates for radioactive isotopes. Results showed that this vanadium alloy can be electroslag melted satisfactorily. The impurities added intentionally were removed or decreased successfully. Among the major alloying constituents, Cr was retained but there were some Ti losses. The latter may be controlled with process refinements. This research suggests that the electroslag melting process could be a suitable method for recycling V alloys after use in future fusion reactors, or for processing other reactive metal alloys with more immediate applications.

Jan 1, 1996

By Gordon Jackson

"There are two accomplishments of air and gas drilling: a new series of economic and mechanical challenges; and, acceptance as a standard drilling and completion tool.The new challenges are related to the concept of using a gaseous circulating medium in drilling for oil or gas. For purposes of discussion, a two part division has been made: the challenge of fluid invasion control and that of equipment and tools. Great strides have been made in the development of materials and techniques to combat formation fluid invasion. Chemicals and the ""mist drilling"" technique, now in use, have the versatility to cope with a wide range of downhole fluid entry conditions.Equipment and tools have been developed to meet the challenges of better, more economic drilling and completion possible with a gaseous circulating fluid. Economic and operational challenges remain.Acceptance of air and gas drilling as a normal operating tool was reached with difficulty. It is now established as a means of reducing costs in exploratory and develop-mental well drilling, exemplified in a recent study of 226 wells covering 419,407 feet of hole in the United States. Air reached the projected depth in 85 per cent of the operations, although formation water was encountered in 48.7 per cent of the holes. Slim hole bit performance and cost all compared for overall bit averages as part of analysis."

Jan 1, 1961

By Ping Zhang, Shahram Mozaffari, Andreas Ylmefors

The risk associated with mining induced seismicity and the related rock bursts has become one of the major threats to the safety and sustainability of mining at the Kiirunavaara mine. The causes of mining induced seismicity at the Kiirunavaara mine are very complex and have affected our understanding on the source mechanisms of seismicity and further the mitigation of the seismic risk. Detailed analysis of historical mining induced seismicity at the Kiirunavaara mine was conducted. The focus of this analysis was placed on the classification of large seismic events and the evaluation of the influential factors on the classified seismic events. 145 events with local magnitude larger than 1.5 that occurred between January 1, 2011 and March 31, 2021 were analyzed. For this analysis, seismic events located in the hanging wall were not included, as these have not been observed to cause large damages to the mine itself. It was found that the magnitude of the events had good correlation with the stress change in relation to the production location. The seismic events were classified as mining-front associated, ore-pass associated, mining-front and ore-pass associated and others, according to their hypocenter location. Most of the mining-front associated events, concentrated around the production levels and slightly above and below them, generally correlated with shear cracks, and most of them occurred when the ore flow between two production levels started. The numerical modelling showed that slip of the geological discontinuity, due to unclamping between hanging wall and footwall, could be the major causative mechanisms, which further supports this finding. The ore-pass associated events are located close to the ore passes. Large seismic events located between ore passes have the source mechanism of both fault-slip and non-shear, but events located at the outer side of ore passes were all fault-slip type. By checking with the ore pass scanning data, it was concluded that the most of the events located between ore passes could be pillar bursts. An elastic core concept has been then used to define a critical pillar width. The paper is not intended to be prescriptive but rather to initiate discussion of the possible classification of seismic events at the Kiirunavaara mine and to present new perspectives of the causes of the seismicity for improving the present seismic risk management.

Apr 26, 2022

By N. S. Dalal, X. Shi

"It has been recently suggested that the exceptionally high antitumor and antibacterial activity of natural fredericamycin A (FMA) is related to its ability to spontaneously generate the superoxide anion (02-) and hydroxyl (""OH) radicals in aerobic solutions [Hilton, B. D., Misra, R., & Zweier, J. L. (1986) Biochemistry 25, 5533]. With a view to understand the mechanistic details, attempts were made to reproduce earlier electron spin resonance (ESR) evidence for the oxygenated free radical formation in well-aerated solutions of natural FMA in dimethyl sulfoxide and dilute H 20 2• Little or no evidence was obtained for the formation of the 0 2- and methoxy (""OCH3) radicals, while the detected formation of the 'OH and methyl ('CH3) radicals was attributable largely to mechanisms not involving FMA. These results thus reopen the T question regarding the mechanism of its exceptionally high tumoricidal-bacteriocidal activity. This paper reports on an electron spin resonance (ESR) investigation of the formation of oxygenated free radicals in solutions of natural fredericamycin A (abbreviated as FMA) which has recently been reported to be a highly potent anti¬tumor antibiotic (Pandey et al., 1981; Warnick-Pickle et al., 1981). The impetus for this undertaking was provided by recent reports (Hilton et al., 1986; Stinson, 1986) suggesting that the strong tumoricidal activity with high therapeutic—toxic index of FMA was related to its ability for the spontaneous generation of superoxide anion (02-) and hydroxyl (OH) radicals. For example, the suggested mechanism for the formation of 02- by FMA was (Hilton et al., 1986)FMA-OH + O2 FMA-O + H+ + 02-Here FMA—OH is simply the FMA molecule emphasizing the —OH moiety which becomes FMA-O, the free radical rep¬resenting the oxidized form of the drug. While some other highly effective anticancer drugs in current clinical application, such as bleomycin, are also thought to exert their antitumor effects via the formation of reactive drug-based or oxygenated free radicals (Carmichael et al., 1985; Gianni et al., 1983), FMA was considered unique in that only in this case the free radical formation was thought to be spontaneous, rather than through a metal- or an enzyme-activated process (Hilton et al., 1986; Stinson, 1986). Thus it was suggested (Hilton et al., 1986; Stinson, 1986) that FMA could be the forerunner of a new class of anticancer drugs. However, we noted that while the hypothesis seemed plausible, the reported ESR spectral evidence appeared to be ambiguous. Because of the high significance of the earlier conclusions (Stinson, 1986), we undertook a systematic ESR study of the radical formation in FMA solutions, and as discussed below, our conclusions disagree with those reported earlier."

Jan 1, 1989

I am honoured and very pleased to have been given the opportunity this evening to say a few words of thanks not only on behalf of all the guests but especially for the delegates and accompanying persons attending the 13th Congress of the Council of Mining and Metallurgical Institutions. Firstly, I would like to congratulate Sir Hamilton Whyte,KCMG for his most interesting address. In his far ranging talk, when he showed knowledge of widely diverse subjects, I had a brief fear that he was going to be talking about the details of support methods in deep level mines, or how to avoid flotation problems in multi-metal mines. Although he did not go that far, he touched on subjects which have arisen this week - long term planning and secure supply of minerals at acceptable prices. The dire predictions of the Club of Rome have been debunked with a far more elastic supply of minerals having been proved. Combined with the importance of a falling birthrate in some parts of the world, this will lead to many changes in the future, when hopefully governments will take the long term view rather than look at the next budget or the next election. Maybe some of them are not too lazy to do this for all of us. However as a fellow Ukranian, I feel that he might have been called something different if he had been in Australia. Sir Hamilton, thank you for your talk. Once upon a time - and this is not a fairy story - there was a cobbler who had two sons; one very bright who became a professor of mathematics; the other, dim, who became a millionaire shoemaker. Asked for the secret of his success, the millionaire attributed it to a vital piece of economics which his father had imparted, "Be content with small margins on a large turnover." "So", said the millionaire, "I make my shoes for $2 a pair and sell them for $5. I am very happy with the three per cent profit."

Jan 1, 1986

By H. L. Teicliman, E. M. Sipprelle

ENACTMENT of Public Law 290 by the 78th Congress authorized the U. S. Department of the Interior, Bureau of Mines, to conduct an experimental program to develop the technology for obtaining oil from oil shale. In adopting and later extending this legislation, the Congress recognized the impending necessity of supplementing ground petroleum reserves with synthetic fuels. Under the provisions of this legislation, the Bureau of Mines, among other things, was charged with the responsibility of developing mining techniques, methods, and equipment for mining the oil shales of the Green River formation of Colorado, Utah, and Wyoming.

Jan 1, 1950

INDEX OF CONTENTS.1. Historical.2. Manufacture.3. Heat Treatment.4. Fatigue, Failures.5. Consideration of the Establishment o£ a Central Testing or Proving Station.HISTORICAL.Since the introduction of improved high air pressure drilling machines in the early part of the century, efforts have been made to develop the quality of the rock drill bit, in order to take advantage of the greater increase of power output per unit weight of the machines (1). This resulted in the change from solid to hollow steel in the second decade of the present century (2).As the greatest sufferers from the dread disease of silicosis (3), it seemed appropriate that the South African gold mines should be the first to use hollow drill steel. Since then solid drills have become practically obsolete for mining purposes.Water is used with hollow steel drills not only to keep the cutting end cool, but also to assist in preventing the formation of undue dust during drilling. It is of interest to note, however, that water fed through hollow steel or sprayed into the air is only partially effective in removing fine dust particles a few microns in diameter, which particles are said to be the most potent in producing silicosis (3a).So far as the composition of "straight" carbon steel drills is concerned, a commission appointed by the Johannesburg mines carried out a very exhaustive series of tests on drill steels.These drills were manufactured from steel made by all the standard methods, including Swedish, Bessemer, crucible, openhearth, and, to a limited extent, electric furnace steel. It should be remembered that the commissioners' report was issued in 1913, when hollow drill steel had not yet been introduced. Only solid steel drills were then in use.

Jan 1, 1947

Objective To characterize the roof fall risk associated with underground limestone mining. Background During the first 5 years of this decade, more than one-fourth of the underground mining fatalities occurred as the result of fall of ground. The large openings in underground stone mines present limitations in observing ground conditions because of floor-to-roof heights ranging from 20 to 60 ft or more. Generally, the status of ground conditions in under-ground stone mines is based on observation and experience obtained during mining development. Some mines use monitoring instruments to gain information on roof conditions, but this practice is typically focused and localized to address issues in a particular area or section of the mine. The Roof Fall Risk Index (RFRI) described here provides a method of systematically characterizing the risk of roof falls to enhance the safety of mine workers. Approach As in many industries, a defective product signals the potential for failure. Similarly, defective rock or strata in an underground stone mine presents a potential risk. Assessing ground conditions relative to the concentration of defects observed provides a way to index or rate these conditions and the subsequent risk. Through observations at approximately 50 underground limestone mines in the United States, strata defects were categorized to develop a quantitative method for determining the RFRI. This method is specifically geared to underground lime-stone mines because strata defects are difficult to see and limited by the experience and knowledge of the observer. Overall, 10 defect categories were deter-mined: 3 that relate to geology, 4 that result from mine development, 2 that are indicative of the roof profile, and 1 that addresses moisture or water flow (see RFRI Chart 1). The defect categories are also weighted to reflect the conditions indicative of roof or strata movement or separation (categories 4 through 8). These weights are multiplied by the assessment value to determine the total category value. The benefit of using monitoring techniques to gain information on roof conditions is also factored into the RFRI for overall assessment of an area in the mine. Each defect category is assessed with a value of 1 to 5 based on parameters as defined in each defect category, with 5 indicating the highest degree or level of defect. The assessment value of 3 is also used when information on a parameter is unknown. The parameters for the defect categories are illustrated in RFRI Chart 2 for use in determining the assessed value. How It Works The RFRI provides a means to categorize the risk for roof falls in underground stone mines. The concept of this calculation is aimed at providing an indication of the level or degree of defect relative to the area of the mine examined. The RFRI for the calculation produces a distribution where RFRI values approaching 0 represent a stable condition and those ap-proaching 100 represent an unstable condition.

Oct 1, 2006

By J. J. Zaluski

The Surface Mining control and Reclamation Act (public Law 95-87) (here-inafter the "Act" or "SMCRA") passed by congress in August of 1977 represents a comprehensive federal scheme for controlling surface coal mining and the surface effects of underground mining through permitting requirements, performance guidelines, and reclamation planning. While the provisions of the Act have been the subject of numerous legal challenges and court battles over the years, it is difficult to identify a more controversial program within the Act than the provisions for designating lands as unsuitable for surface coal mining operations. The lands unsuitable designation process provides for the acceptance and review of petitions submitted by citizens or organizations seeking to have specified land areas designated unsuitable for all or certain types of surface coal mining activities. In filing these petitions, the interested parties or petitioners are required to make allegations about potential adverse impacts on people or the environment and submit evidence supporting their allegations.

Jan 1, 1992

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro, NC, treating crude Waelz oxide (WOX) to produce special high-grade zinc by a hydrometallurgical process comprising leaching, zinc solvent extraction/electrowinning, melting and casting and bleed treatment. Cadmium removal by zinc-dust cementation plays an essential role in the bleed treatment circuit to prevent cadmium buildup in the circuit. Silica, though present at a low level of approximately 0.3 percent in the WOX feed material, had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also affected. To identify the source of the silica issues, silica levels were mapped throughout the circuit, and adjustments, including using pregnant leach solution as the feed to cementation, and pH control in the WOX leaching and neutralization were introduced to mitigate the issues created by silica gel in the circuit. IntroductionLocated in Mooresboro, NC, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz oxide (WOX) to produce special high-grade (SHG) zinc. The flowsheet, known as the Modified Zincex process, consists of leaching, solvent extraction (SX), electrowinning (EW), melting and casting and bleed treatment (Fig. 1). Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press.At the refinery, WOX pulp is leached at a controlled pH to achieve the maximum zinc extraction, according to the main reaction:"

Jan 1, 2016

By S. B. Mishra

Ni-20Cr metallic coating was deposited on a Ni-based Superalloy (3Fe-19.5Cr¬0.3Ti-Balance Ni) by a shrouded plasma spray process; NiCrA1Y was used as a bond coat. Erosion studies were conducted on uncoated and plasma-spray coated superalloy specimens using an air-jet erosion test rig at a velocity of 40 m/s and impingement angles of 30° and 90°. The coating has been characterized for porosity, microhardness and microstructure and X-Ray Diffraction (XRD). An electron probe micro analyzer (EPMA) was used to obtain X-ray elemental mappings of the coating along the cross-section. Scanning electron microscope (SEM) with EDAX attachment was used to analyze the eroded surfaces.

Jan 1, 2005

By M. Tokoglu

Accurate estimation of resources is one of the major challenges in mineral project evaluation. Contemporary mineral resource estimation practice calls for contribution from several disciplines and execution of several interdependent tasks. 3D estimation domain modelling is obviously one of the most essential components of such a substantial process which forms the basis of this research. The study constitutes a comparative analysis of four major domain modelling techniques; (i) explicit modelling, (ii) implicit modelling, (iii) indicator kriging, and (iv) conditional simulation. It involves comparison of outcomes for alternative scenarios to assess the implications of the modelling decision on resource estimates of a polymetallic massive sulfide deposit located in western Turkey. Thus, identical grade estimation method and parameters are considered to identify the discrepancies arising only from the choice of the domain modelling approach and underlying assumptions. Economic implications are demonstrated in the form of range of outcomes for the extends of the ultimate pit, ore tonnages (min:37.0 Mt, max: 46.7Mt), waste tonnages (min:201.2 Mt, max: 251.2 Mt), stripping ratios (min:5.18, max: 5.71), and total pit values (min: $1.05B, max: $1.45B). Examination of solid models as well as cross-sections revealed that major discrepancies are observed beyond outlying drillholes. Therefore, it has been proposed that assumptions regarding extrapolation distance is the main source of mentioned dissimilarities. Key words: Domain modelling, explicit modelling, implicit modelling, indicator kriging, conditional simulation INTRODUCTION Resource estimation is apparently a challenging process calling for extensive expertise and input from several sources, each of which introducing its related uncertainties. In the last decades, substantial role of quantitative analysis of several forms of risk and uncertainty in evaluating projects’ upside potential and downside risks has been realized. Studies indicated that mining companies have been severely impacted because of not meeting project expectations. As noted by Vallee (2000) “… in the first year of operation after start-up, 60% of mines surveyed had an average rate of production less than 70% of designed capacity”. Several other studies on mining projects also revealed that uncertainties related with the resource model are one of the major contributors of mentioned shortfalls. In this perspective, quantification of uncertainties associated with each component of estimation process is critical. 3D estimation domain models capturing major mineralization controls are the fundamental components of contemporary mineral resource estimation. Domain models are key guiding tools for estimation and are products of a complex process involving many unknowns and assumptions. There exists a number of 3D modelling alternatives which are distinct with respect to complexity, time and effort involved. Acknowledging potential influences on downstream mining practices and relavent economic implications, risks and uncertainties associated with 3D domain modelling are critical yet poorly studied aspects.

Jan 1, 2019

By J. E. Urosek

Decisions made during a response to a mine fire or an explosion greatly affect the final outcome. The safety of miners should be the primary concern with accounting for all of the miners the first issue for resolution. If miners have not safely evacuated from the mine, the last known location of the miners at the time of the event and anticipated travel routes are primary exploration areas. After the mine is evacuated, there are many very important decisions that must be made quickly and often under great stress. It is critical that the mine operator establish an orderly method to direct the mine emergency response. Designation of a Command Center, staffed with personnel charged with developing plans, is a common method of establishing control. Scheduling of key mine managers will be critical, since decisions must be made 24 hours a day and people working for extended periods with little or no sleep do not always make clear or cognizant decisions. Internal communications, passing information on to subsequent shifts, and external communications with families and media must be accurate and timely. Assembling resources for responding to the mine emergency is critical for an effective response, and pre-planning can pave the way to a successful recovery. Sampling mine gasses and accurately determining the composition of gas mixtures is a common tool used to develop response plans in all fires and explosions. It is essential that preparations for emergency situations are made well in advance of a disaster. Effective communications are essential for mine management to successfully respond to a mine emergency. This paper discusses some considerations which need to be addressed in directing a response to a mine fire or explosion.

Jan 1, 2009

By Ch. R. V. S. Nagesh, Ramesh Naidu Mandapati, Venkata Swamy Nalajala, Tondepu Subbaiah, Naga Jyothi Kothamasu

Leaching studies of magnesite obtained from Tamilnadu Magnesite Limited, Salem, have been carried out using hydrochloric acid leaching and percentage of magnesium chloride recovered was estimated. The variables considered in this study were the following: duration of leaching, volume percentage of hydrochloric acid, temperature, and pulp density. Percentage recovery of magnesium chloride increased with duration of the leaching, volume % of concentrated hydrochloric acid, and temperature. Percentage recovery of magnesium chloride decreased with increase of pulp density. The optimum conditions found to be pulp density (10%), hydrochloric acid concentration (30%), duration of leaching (2 h), and temperature (348.15 K). Iron was removed by treating the leach liquor with hydrogen peroxide and by raising the pH to 3.5–4. The purified leach liquor was subjected to spray drying for producing high pure magnesium chloride.

Jun 7, 2022

By Cláudio Batista Vieira

Nos últimos dez anos grande atenção tem sido dada a tecnologia de realidade virtual, sendo sua aplicação cada vez mais marcante para o desenvolvimento de ambientes virtuais imersivos em diferentes áreas. Nesse trabalho é apresentada uma descrição da plataforma inovadora em realidade virtual de uma planta industrial de produção de ferro-gusa verde. O modelo 4D do alto-forno a carvão vegetal contempla o projeto detalhado de engenharia dos equipamentos e a partir da integração de softwares e hardwares foi modelado um ambiente tecnológico em realidade virtual de alto grau de realismo. Essa plataforma foi customizada para ser utilizada como Indústria-Escola de Educação Profissional para escolas técnicas, universidades, institutos de pesquisa, indústrias e museus. A Usina-Escola Siderúrgica utiliza um sistema de blended learning, agregando assim as vantagens existentes tanto na modalidade do ensino presencial tradicional, como na abordagem do ensino a distância.

Aug 1, 2018

By J. Aydt, W. McCombe, H. McLaughlin, L. Nightingale-Mercer

The McClean Lake mill is located approximately 850 kilometers north of Saskatoon, Saskatchewan, Canada and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and in 2014 completed a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum. This expansion included significant changes to the mill’s secondary leach circuit in support of safely processing high grade ore directly from the Cigar Lake mine. In particular, inter-stage pumps were introduced for slurry transfer between the secondary leach tanks, replacing the original pressure feed forward operation. The design and selection process for these pumps was strongly influenced by the uncertainty related to actual radiation dose exposure when processing undiluted high grade ore (up to 30%U), and consequently the desire to maintain minimal occupancy in the vault enclosure containing the secondary leach tanks. These constraints resulted in the decision to install positive displacement pumps above the leach tanks in a suction-lift configuration. Operating experience with this design has shown that the pump capacity is significantly de-rated due to process solution gas-entrainment and pipe scale build-up, particularly in the front end of the secondary leach circuit where reagent dosage is high. Experience processing high grade ore also provided accurate radiation dose data to demonstrate that the level of occupancy in the leaching vault enclosure could be re-evaluated to accommodate alternate pump configurations. This paper reviews the lessons learned and improvements made to safely increase the capacity and reliability of the leach inter-stage pump system.

Jan 1, 2020

By Clyde E. Williams

MORE has been said about the iron and steel situation on the Pacific Coast than has been done .about it; but perhaps as much has been done as conditions have warranted. The production of finished steel in an amount sufficient to take care of the local demand for certain sizes and shapes is an established industry on the .coast. The amount .and the variety of products, so made, changes with the demand or them which is largely dependent upon the growth in population. An increasing demand will not always increase the quantity of steel produced locally because the cost of production may rise so -high as to let in steel from the outside. The reason for this is that all of the steel made in the West comes from steel scrap, the supply of which is .limited. From the standpoint of the metallurgist, it would. be desirable to subititute pig iron for some of ' the steel scrap, but this cannot be done profitably because the pig iron now available is too expensive. In other words, the large future demand for steel and pig iron on the Pacific Coast must be supplied by reduction of ores in the West, unless we are to be content with paying high transportation costs for material produced elsewhere. ."

Jan 1, 1924

By A. G. Pathan

Rock and soil mechanics investigations were carried out in block VIII at Thar Coalfield, Pakistan. Most of the strata were mainly composed of sand, with an average content of 67.68 %. Laboratory studies of rock and soil samples from drill hole GT-01 revealed that the strata in block VIII are very weak with an average uniaxial compressive strength of 3.59 MPa, an average tensile strength of 0.68 MPa, an average Young?s Modulus value of 0.234 GPa, an average cohesion of 129.19 KPa, and an average friction angle of 55.47°. Slope stability analysis, based on a probabilistic approach, was carried out using Slide-V software. Monte Carlo simulations have been applied to investigate the probability of failure in the slopes of an open pit lignite mine in block-VIII. From the slope stability investigation, it was found that the probability of failure is 0 % at a slope angle of 16°.

Aug 1, 2013