Search Documents

By A. J. Potgieter, C. Hill, A. Humpel, D. S. Magudulela, V. Scholtz, A. Coetzee

Keywords: Pyrometallurgy, long steel products, coke, sinter, blast furnace, steel plant Located in Northern KwaZulu Natal, Mittal Steel South Africa Newcastle works produces roughly 1.8 million tons per annum, supplying long steel products, locally and overseas. The great extent of local raw material availability and low conversion cost ensures that Mittal Steel South Africa is among the lowest cost, high quality producers of steel. MSSA Newcastle works can be subdivided into two main sections: The iron making side, comprising the coke ovens, sinter plant and blast furnace, and the steel making side, comprising the basic oxygen furnace, ladle furnace, continuous casters, and the medium, rod, and bar mills.

Jan 1, 2006

By L. E. Young

THE purpose of this paper is to start a discussion on: (1) methods of supporting the immediate roof, particularly of local areas of poor roof, during the mechanical loading of coal; (2) methods of increasing the rapidity of the movement of the mining faces so that, without the use of cribs, jacks, pack walls, and filling, there will be no danger to men, equipment,, and working places from the subsidence of the overlying strata. In the Pittsburgh district the application of mechanical loading devices in mines working in the Pittsburgh seam, has been retarded by the difficulties of holding and handling the draw slate. Normally the thickness of this slate averages about 8 in. but the hardness varies, and a cut of coal cannot always be loaded without placing posts or crossbars to support the slate. Locally, the slate may be thicker and special methods of support may be required. If crossbars are placed to hold the slate when the coal averages 5 ft. in thickness, the standard methods of transporting the coal cannot be followed, and the use of conveyors may be desirable. Very little information is available on the effect of increasing the rate of movement of advancing or retreating break lines or longwall faces. A few British publications have presented some data but all such data relate to longwall faces that have moved not more than 6 ft. a day. The most rapid rate of movement of longwall faces in Germany is 6 ft. per day. In the ordinary hand-loading mine in western Pennsylvania break lines on full retreat will move about 2 ft. per day. If loading machines are used under similar conditions the, rate of retreat may reach 4 ft. per day. In a mine where coal is loaded by hand on conveyors three shifts per day, the rate of retreat has ranged from 11 to 16 ft. per day, with an average of 13 ft. If mobile loading machines could be used to load on con-veyors on break lines, the rate of retreat should be increased substantially.

Jan 1, 1938

By R. M. GRANTHAM, J. H. SOULE

C. R. Keyes, F. C. Schrader , F. A. Jones ( the first director of the New Mexico School of Mines , whose name was given the deposits ) , and N. H. Darton all described the Jones iron deposits within a decade after their discovery in 1902 . The earliest locations now on record were made in 1927. Interest in iron ores was revived during the second World War . Paul E. Pesonen , of the Bureau of Mines , reported on the deposits in December 1941 and proposed an extensive exploratory program . In March 1942 , the deposit was reported upon by C. H. Johnson , also of the Bureau of Mines , and a definite program of exploration was outlined .

Feb 1, 1947

By Noboru Masuko, Sachiko Ono

"The structure and composition of anodic films formed on aluminum in a borate solution have been investigated by using TEM and SIMS with respect to the effect of current density and electrolyte temperature. The film is composed of a boron-containing outer layer and a boron-free inner layer with disc-like crystals present at the interface. The thickness of the film formed at constant current density up to an identical voltage, decreases with increasing current density. The thickness increases remarkably with elevated temperature. The transport number of Al3+ estimated from the thickness ratio .of the cuter to the inner layers is 0.4 when the film is formed at the current density of 20 Am-2 at 60°C. It increases slightly with increasing current density and decreases significantly with increasing temperature. Content of boron in the outer layer increases 1.5 times when current density .increases 10 times. These changes in film structure and composition with electrolysis conditions must have a significant role in the determination of electric properties of anodic alumina films as a capacitor material.IntroductionThe growth of anodic alumina film in ·a neutral electrolyte proceeds at both film/electrolyte and film/substrate interfaces giving a duplex structure. The oxide layer formed at the former interface includes electrolyte anions while a-pure alumina layer is formed at the latter interface. The thickness ratios of each layer respectively represent transport numbers of Al3+ and 0 2 - (1). The film thickness and the incorporated anion content as well as transport numbers of both ions must affect the dielectric properties of the film as a capacitor material. However, the correlation between film structure and electrolytic conditions is not fully understood (2). For the further clarification of anodic film growth mechanism, more detailed characterization of anodic films in relation to electrolytic conditions is advantageous. In the present paper, therefore, the effect of current density and electrolyte temperature on the microstructure and composition of anodic barrier films formed in a neutral borate solution was studied. The films were characterized by direct observation using transmission electron microscopy (TEM) and depth profiles of constituent elements obtained by secondary ion mass spectroscopy (SIMS)."

Jan 1, 2000

By John E. Murphy, Ernest L. Ohle

Hematite-magnetite ore bodies at Iron Mountain, Missouri, have produced nearly 9 million tons of iron ore concentrates since 1844. The ore minerals occur principally as open-space filling in fractured and brecciated andesite porphyry with very minor replacement of the wall rocks. The enclosing rocks are Precambrian in age and consist of a series of dacite, rhyolite, and andesite flows aggregating about 2000 feet in thickness. All of the ore is in andesite and the mineralization is Precambrian in age. The shape of the ore bodies, the breccia character of the ore, and the gangue mineralogy are believed to be unique. One of the two main ore bodies is crudely dome-shaped with a tendency for development of concentric mineralized shells; the other is an elongated lense in plan but hook-shaped in cross section. Both have strong linear elements striking northeast, east-west, or northwest. Various modes of origin for the structures and for the tension breccias have been suggested, but none is completely satisfactory. Hematite is the main ore mineral; magnetite is subordinate. Important gangue minerals are andradite, quartz, calcite, actinolite, apatite, epidote, and chlorite. Although some evidence favors injection of an iron-rich melt, other evidence suggests ore formation by a high temperature, water-rich solution.

Jan 1, 1968

By E. N. Mounsey

The paper addresses the design of the Zhong Tiao Shan Company (ZTS) Houma Ausmelt Technology copper smelter in People's Republic of China. The smelter represents the third copper smelter development using Ausmelt Technology, the first large scale (35,000 tpy blister copper) and the first smelter to use the Ausmelt Technology smelting and converting process steps in separate TSL vessels in a continuously operated process. The project will be realised through the combined efforts of ZTS, Ausmelt and ENFI, the Beijing Non-Ferrous Engineering Institute who provided partial detail engineering services in China. Ausmelt will provide the technology licence, basic and detailed furnace engineering packages and additional technical services including cold commissioning support and hot commissioning supervision.

Jan 1, 1999

A project was funded by the Australian coal industry to investigate the mechanisms that might lead to sample bias when using cross-belt cutters, in order to help coal industry personnel to make better decisions about the purchase, maintenance and operation. It concentrated on DEM modelling of skew cutters. These are set at an angle to the belt with the intention of minimizing disturbance to the non-sampled material. Two bias mechanisms are likely to cause bias for cross-belt cutters. Waves of material are bulldozed off the belt by the upstream side of the body of square cutters and material is thrown by the leading edges of cutter blades for all types of cross-belt cutters. These mechanisms cause some parts of the load of material on a belt to be over-represented. The effects of these mechanisms cannot be made to be negligible, so cross-belt samplers cannot be trusted to produce unbiased samples, especially for segregated streams of material. However, it is possible to give a bound on the maximum likely bias. The grades of two portions of the stream can be estimated by stopping the belt and shovelling off 1/3 of the cross-section of the load on the belt into a container, concentrating on the final side of the belt and the top of the load. The remaining material should be put into another container and the difference in grade determined. The maximum likely bias is typically about 10% of this difference. For a cross-belt cutter, having an extraction ratio near to 100% is not a reliable indication that the cutter has little or no bias. Some bias mechanisms affecting cross-belt sample cutters make sample mass too high and some make it too low, so an extraction ratio near 100% can occur if two bias mechanisms are both active. Keywords: sampling, DEM simulation, sample bias, accuracy, precision

Jan 1, 2009

By P. Lefebvre, J. Sargent, K. Major, B. Darnton

"Stillwater Mining commenced mining operations at Nye, Montana in 1987 for the recovery of platinum and palladium. Exploration identified that the J-M Reef extended for 43 km. In 1998 Stillwater Mining made the decision to develop the East Boulder mine complex, located approximately 13 miles from the Stillwater mine complex at Nye, to increase production. This paper describes the design, construction, and start-up of the East Boulder process plant.INTRODUCTIONStillwater Mining Company have been producing Platinum and Palladium from their Nye, Montana operations since 1987. The mine production from Nye had been increased in stages with mine production being delivered through several portals and one vertical shaft.The deposit is narrow veined which prevents the application of bulk mining methods and thus limits the production capabilities.In order to increase the production of platinum (Pt) and palladium (Pd) Stillwater made the decision to access the ore from the J-M Reef from the East Boulder site. The East Boulder mine site is located about 21 km (13 miles) from Nye, however as shown in Figure 1, the travel distance is closer to 188 km (114 miles). Distance, on strike, and space availability at Nye precluded the expansion of the Nye concentrator to handle the increased mining rate and supported the decision to install a new concentrator at East Boulder."

Jan 1, 2003

By J. L. Jambor, T. C. Birkett, W. D. Sinclair

Abstract -The rare-earth elements (REE) form a significant part of the group of so-called "high­ technology" metals whose glamour has attracted both the scientific community and the mining industry. Despite this attraction, world production of REE declined abruptly in 1985 and only recently has begun to approach production levels of 1984. The decline in 1985 was primarily due to decreased demand for light REE used as catalysts in the production of lead-bearing gasoline. Incorporated within the current trend toward increased production of REE is an increasing demand for higher value elements such as yttrium and other members of the heavy REE group, and for specific REE rather than mixed products . The former demand has made some Canadian deposits and prospects economically attractive despite a surplus of REE reserves on a world scale. The chief attractions of Canadian deposits such as Strange Lake, Labrador-Quebec, Thor Lake, Northwest Territories, and Kipawa, Quebec, are that they are relatively rich in yttrium and other heavy REE compared to light REE, and that they offer a potential security of supply to counterbalance the rapidly escalating dominance of China in the world market.

Jan 1, 1992

By Douglas A. Sloan

"Shutdowns and breakdowns that halt the process-flow of mine production are costly. Skilled maintenance tradesmen are scarce and expensive. The cost of maintenance or of production Joss from Jack of maintenance is significant and warrants considerable managerial attention.The most appropriate maintenance policy is dependent on an economic calculation. At one end of the spectrum is the policy of avoiding all breakdowns by replacement and preventive routines before failure, such as the airlines policy. At the other end of the spectrum is the policy of minimal routines and the acceptance of a breakdown as a prelude to a repair.The complexity and cost of maintenance warrants the appointment of a maintenance manager of senior status. Within the origination, there are a number of activities that can be specialized to improve effectiveness. Among these are the inspectors' activity, the establishment of improvement routines, the planning of repair tasks, maintenance engineering research and value analysis.The maintenance system is the mechanical aid to assist the staff in the implementation of the policy. It is designed to facilitate planning to make the best use of the resources. It provides information to identify areas where managerial action is required to make improvements. The job ticket is the basis of most systems."

Jan 1, 1970

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By C. E. Hunt

Since the turn of the century, copper-nickel sulphide ores have been processed at the Sudbury, Ontario operations of INCO Limited, currently the largest integrated mining, milling, smelting and refining complex in the free world. Through the years operational, ecomomic, social and legislative changes have dictated the need for research and development directed at mitigating the impact of existing operations on the surrounding natural environment and also the reclamation of areas affected by earlier mining activities. Approximately one hundred years of mining history and the current annual processing of some 12 million tons of ore presents significant challenges with respect to waste disposal, liquid effluent treatment and land reclamation, particularly in light of rapidly evolving environmental regulations' and controls within the Province of Ontario.

Jan 1, 1992

By L. Don Leet

Abstract Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. The nature and magnitude of vibrations from various sources have been investigated and certain applications of the knowledge thus gained have been made. Vibrations from blasting have been measured on special equipment over a range from an electric blasting cap at a few feet, through the largest quarry shot in history to date ( 1,-362,985 lb.), to the first atomic bomb, in uew Mexico on July 16th, 1945. Laws relating amount of explosive to amount of vibration at different distances have been developed and tested. Special studies have been made of the effects of vibrations on buildings, particularly from the standpoint of possible structural damage. Recorded vibrations are used to study the effects of modern short-period delay shooting. It ?has been found that short-period delay firing is extremely effective in reducing vibrations under the right conditions, but with certain limitations. In quarry shooting, there appears to be a minimum number of holes below which vibrations are not appreciably reduced by short-period delay firing. In several instances this minimum has been near 7. Vibrations in the ground from rock bursts and the effects of mining in stresesd ground have been studied both underground and on the surface in a search for a rock burst warning system. Introduction Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. Analyses of blasting records have been yielding increasing funds of information of practical as well as theoretical interest. The nature and magnitude of the vibrations have been investigated with special reference to their effects on structures.

Jan 1, 1951

By Richard Keith Corbin

Canadian junior mining companies whose gold exploration and exploitation programs take them across the border into the western United States should be prepared to deal with the myriad of title issues involved in acquiring unpatented gold mining claims. The purpose of this paper is to serve as an introductory outline for Canadian junior mining companies to mining laws of the United States, as well as to relevant laws of some of the western gold mining states. Topics will include the five w's (who, where, what, why and when) of Canadian junior mining companies1 rights and responsibilities in acquiring interests in U.S. gold mining properties by claim staking, lease or purchase. Historic terms of common parlance among U.S. miners, such as "claimjumping" are defined and discussed. Various legal doctrines, such as "pedis possessio" and "good faith" in the location of claims are covered as well. Controversial subjects of contemporary interest are addressed in some detail, such as whether to locate a bulk-mineable disseminated gold deposit with placer claims or lode claims, and whether lodes may be staked over placers. By thus heightening the awareness of Canadian junior mining companies, it is hoped that they can be properly prepared to avoid title disputes, and to win lawsuits when they are unavoidable.

Jan 1, 1988

By C. L. Peng, F. F. Min, S. X. Song

"Using a parameter representing the degree of hydration of particles in a liquid called hydration index I, which we derived based on Einstein’s viscosity equation, we evaluated the degree of hydration of fine montmorillonite particles in different aqueous solutions by measuring the viscosities of the montmorillonite dispersions and plotting relative viscosity against volume fraction of dry montmorillonite particles in the dispersions. We investigated the effects on the hydration of montmorillonite in aqueous solutions of (1) the type and (2) the concentration of electrolytes in the solutions and (3) pH. For the same concentration of electrolytes, the hydration index I of montmorillonite was found to increase in the order of Na+ > K+ for monovalent cations and Mg2+ > Ca2+ for divalent cations, and to decrease with increasing valence of cations in the order of Na+ > Ca2+ > Al3+. For both Na+ and Ca2+, the hydration index I first increased with increasing concentration of electrolytes and then decreased after a certain concentration. The hydration index I increased with increasing pH. IntroductionClay minerals have the distinctive ability to adsorb water molecules and hydrated cations in aqueous solutions, resulting in hydration on their outer surfaces and in their interlayer spaces. Many investigators (Jurinak, 1963; Anderson and Tice, 1971; Costanzo et al., 1982; Israelachvili, 1992) had found evidence of ice-like structures of water on clay minerals.This phenomenon of hydration plays an important role in the dispersion and sedimentation of clay minerals in aqueous solutions. To understand clay hydration, numerous experimental and simulation studies have been carried out since 1933, including the recent ones of Hawkins and Egelstaff (1980), Skipper et al. (1995), Karaborni et al. (1996), Salles et al. (2013) and Morrow et al. (2013). Among the factors that can influence a clay mineral’s hydration characteristics are chemical composition, type and degree of isomorphous replacement in its structure, and number and nature of associated exchangeable cations."

Jan 1, 2015

By Douglas N. Kendall

There are three definite steps in the making of a mining industry in any country. These are as follows: Step A - Geological Mapping This step covers the basic geological mapping of the country at scales of 1/250, 000 up to l/50, 000. This step eliminates territory and directs the exploration teams to the areas of potential interest. Step B Prospecting This step includes all phases from detailed geology through geophysics and drilling up to the point of proving that an economic ore body exists. Step C - Mine Development This is the expensive step, involving the creation of the mine, including shaft-sinking, ore treatment plant, etc.

Jan 1, 1963

By Soheil Bahrampour

Void detection and identification of bed separation while drilling holes in rocks for roof bolting can be a great source of information for the evaluation of ground conditions and adjustment of ground control or support measures. This can be accomplished through the monitoring and analysis of drilling parameters by the roof bolter. This paper reviews work currently under way in a joint study between Penn State University and J. H. Fletcher & Co. The detection of voids, along with identification of rock types, can lead to development of 3D roof maps, which can subsequently be used to evaluate ground support and its suitability for given ground conditions in tunneling and mining operations. Existing algorithms for void detection utilize the sensory information of the drill unit, such as feed and rotary pressure, revolutions per minute (RPM), and penetration rate, to detect voids or joints on the roof/ ribs. While the void detection algorithms are being revised to allow analysis of available data from the existing sensory systems of the roofbolters with higher accuracy and lower number of false detections, additional sensors have been added to the drill to improve its ability for accurate detection of the voids and joints. This includes installation of vibration and acoustic sensors on a drilling unit at J. H. Fletcher & Co., and pertinent data analysis which are discussed in this paper. Initial results indicate that the data obtained by vibration and acoustic sensors at high sampling rates can be used to improve the performance of the void detection algorithms independently, and when combined with the modified algorithms using existing sensors, it can substantially improve the capabilities of current void detection system.

Jan 1, 2013

By Leiv Kolbeinsen, Stian Seim, In-ho Jung

"The current work presents new experimental data in the iron-unsaturated region of the FeTiO3-Ti2O3-TiO2 slag system. The samples are prepared by melting pure reactants in a high frequency induction furnace that employs a cold crucible. A similar experimental set-up has been described in literature and proven suitable to investigate high titania slags. The FeO content of the samples range from 3.7 to 21.8 wt% and the Ti2O3 content range from 3.6 to 30.1 wt%. The liquidus temperatures of the samples are measured in-situ by a spectropyrometer and range from 1450 to 1645 °C.In addition, an improved thermodynamic database for the FeO-Ti2O3-TiO2 system has been developed. Ternary parameters have been included and optimized to fit previously published experimental data. This optimization minimizes the discrepancy between experimental data and thermodynamic calculations as previously discussed in literature. New liquidus projection plots are proposed for the FeO-Ti2O3-TiO2 and the FeTiO3-Ti2O3-TiO2 systems.IntroductionIlmenite (FeTiOs) smelting is a relatively small industry world-wide. However, a reasonable focus on the process has been applied in Norway due to the location of one such smelter in Tyssedal, which is located in the western part of Norway. The process is essentially carbothermal reduction, where most of the iron in the ilmenite is reduced to its metallic state, and the titanium oxide is concentrated in the slag product. The metallic iron is sold as a high purity pig iron and finds applications in cast products. The slag concentrate is further processed for the production of TiOvpigment and/or titanium metal. This further processing can be performed through different routes according to the purity of the slag concentrate."

Jan 1, 2012

By Vivek Samu, Murthy Guddati

A new method called Effective Dispersion Analysis of Reflections (EDAR) was recently developed to effectively analyze the dispersive waves generated from lateral impact to piles. This paper presents the results of nondestructive length estimation of existing piles through EDAR. EDAR provides a new visualization method for analyzing wave reflections by transforming the response into the frequency domain thus eliminating the need to perform difficult peak picking in the time domain. In addition to being able to analyze dispersive waves, EDAR also incorporates the effects of radiation damping due to the surrounding soil leading to more accurate length estimates. Concrete filled steel tubes of different embedment depths were tested both in laboratory and field conditions. Length estimates obtained were within 10% error margins after careful analysis accounting for the presence of soil effects and effects from pile top reflection.

By Nilmani M, Malone J, Taylor RN, Floyd JM, Gray NB, Fountain CR

CSIRO staff and University of Melbourne staff and students collaborated in an intense programme of investigation on the CSIRO 50 kg Sirosmelt pilot plant.In two days of operation copper matte converting and zinc slag fuming trials were performed, whilst investigation of the process dynamics and process chemistry was carried out. This exercise is an example of the techniques available for process evaluation, which can rapidly advance the understanding of pyrometallurgical operations by use of a team approach covering a wide range of experiments.

Jan 1, 1985