Search Documents

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976

By S. E. Olsen, M. Tangstad

The main source of Mn in raw materials for SiMn production is Mn-ore and Mn-rich slag from the high carbon FeMn production. The amount of slag per tonne of SiMn metal is mainly determined by the ore/slag ratio. Increasing share of FeMn slag at expense of Mn-ore will lead to larger slag/metal ratio in the SiMn process. High volume of slag leads to an increased consumption of energy and probably to higher losses of metal inclusions in the final slag. Excavation of a SiMn furnace has shown that only modest pre-reduction of Mn-ore with CO gas seems to be obtained. Nearly all reduction of MnO was finished at the top of the cokebed. Dissolution and reduction of quartz obviously takes place in the cokebed zone after the main reduction of manganese oxide is finished. Probably the ?pick up? of Si in the metal is quite fast and takes place as the metal trickles down through the cokebed towards the metal bath. The distribution of Si between SiMn alloys and multicomponent MnO-SiO2-CaO-Al2O3-MgO slags is mainly determined by the process temperature, the silica content of the slag and its R-ratio = (CaO+MgO)/Al2O3. As an example, the equilibrium content of Si in the alloy will increase by about 6 % if the R-ratio is reduced from 2 to 1, provided constant temperature and silica content. The effect of temperature is also considerable. The equilibrium content of silicon will increase by approximately 6 % per 50°C in the temperature range 1550°C to 1700°C. The equilibrium content of MnO in SiMn slags depends first of all on the temperature and secondly on the silica content of the slag. At 1600°C the MnO content decreases from about 9 % at silica saturation to a minimum of about 3-4% when the silica content is reduced to about 40-45%.

Jan 1, 2004

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

About 15 per cent of total electricity (400 MkW) was generated by nuclear power plants in the world (2009) and about 36 000 tons of uranium has been mined in uranium mines annually. Radioactive waste material is produced from uranium mines and nuclear power plants. The wastes must be disposed or stored safely for long-term. If they leak and/or move from disposal or storage sites due to air/groundwater flow, then a serious environmental pollution can occur. Hence, multi-layer system has been proposed and employed in order to seal off these radioactive waste materials from biosphere. Basically, bentonite is now used for establishing absorbing and sealing layers in this system. However, the amount of high quality betonite is very limited and in some cases it is hard to be obtained.On the other hand, a great deal of refuse from coal burning plants is produced every year and the amount of it is expected to be higher each year, especially in developing countries. More than half of flyash is utilised and the remaining is disposed at the disposal sites. However, the life of the disposal site is limited and it is diff cult to find a new disposal site. It is requested that the percentage of the utilisation of the flyash be increased in every field.From the above two points of view, a flyash-based barrier layer/cover system is considered in this research and this paper discusses the applicability of flyash as a content of barrier layer/cover material based on the results of a series of laboratory tests.

Dec 6, 2010

By T. R. Waters, F. Li, R. L. Huston

This paper describes the development of a multi-body biomechanical model that can be used to assess the risk of low back disorders due to occupational exposure to jarring and jolting from operation of heavy mobile equipment (e.g., trucks, haulers, graders, tractors, etc.) The four-element dynamic spinal model is capable of providing estimates of the force and acceleration responses of the head/neck, upper, lower, and middle torso resulting from vibration input collected in field studies. The paper also presents a method for using the model output to assess an individual's risk of low back disorder due to a specific jarring and jolting exposure.

By W. G. Jewitt

Introduction The use of the aeroplane in prospecting is already familiar to everyone connected with the mining industry. Apart from transportation companies, three organizations, the N. A. M. E., the Dominion Explorers, and the Exploration Department of the Consolidated Mining and Smelting Company, have made the aeroplane an everyday feature in every mining district in Canada. Its use has been demonstrated successfully in the mountains of British Columbia, but perhaps its greatest field lies in the Canadian Shield, where the numerous lakes and rivers afford an almost continuous series of landing places for aeroplanes, on floats in the summer and on skis in the winter. To the man who has travelled by canoe, toiling over fly-infested portages or held for days at a time, wind-bound, on the big lakes, the ease, speed, and cheapness of aeroplane travel have marked the beginning of a new era, in which ground previously covered with difficulty in a month or more is travelled with ease in a few hours. Development of an air service in the Consolidated Mining and Smelting Company has proceeded on different lines from those of other organizations, and this paper is concerned with that development.

Jan 1, 1931

By Tracie Zoeller, G. Paul Neitzel, Jr. Sanders

"As-cast aluminum alloy microstructures are highly segregated. Coring occurs when solute is rejected during solidification resulting in a non-uniform solute distribution across the dendrite arms. Furthermore, coarse constituent phases are formed in the interdendritic channels as a result of coring. These constituents are either soluble or insoluble and can form from the major solute elements, or the impurity elements iron and silicon. The dissolution of these constituents, or precipitates, is an important consideration in determining the microstructural evolution of an alloy. The properties of an alloy are significantly affected by the morphology of the precipitates. Precipitates can be either beneficial or detrimental to the properties of the alloy. Regardless of the nature of the precipitates present, it is useful to understand the dissolution process. A diffusion-limited dissolution model for planar precipitates is presented and compared to an analytical solution and to models in the literature. Experimental data for the dissolution of AhCu precipitates in a dilute alloy are compared to the proposed model, and found to have good agreement.IntroductionDuring the processing of precipitation hardening alloys, beginning with the solidification step and ending with the final solution heat treatment step, there are a variety of particles that form. Some of these particles must be dissolved and solute redistributed and re-precipitated in a more homogeneous distribution than as it first appears in the as-cast microstructure. The particles can be classified by size as microstructure develops during processing. Coarse particles that form during solidification can either be soluble, partially soluble or insoluble. These particles can be the result of coring of the major solute elements as well as the limited solubility of elements such as iron and silicon. Iron and silicon can combine with the major solute elements such as copper in 2xxx alloys forming coarse phases often referred to as constituents. Figure l(a) shows the as cast microstructure with the constituent phases, Al2Cu and the insoluble phases containing Al-Fe-Mn-Cu-Si [7]. During preheating the soluble phases such as AhCu that were formed by eutectic decomposition must be taken back into solution, whereas the insoluble phases remain essentially unchanged by most thermal operations. Figure l(b) and (c) show some of these constituents after subsequent preheating steps. In Figure l(b), AhCu platelets are shown and in Figure l(c) the remnants of the AhCu phase are noticeable, along with Mn-bearing dispersoid phases. Reduction in the volume fraction and size of these phases improves the ductility and fracture toughness as well as reducing the inhomogeneities that occur during coring. Also adjacent to the dendrite arm boundaries are smaller AhCu phases that precipitate by a solid-state transformation on cooling to room temperature."

Jan 1, 2004

By Charles S. Ney

"ZINC-LEAD REPLACEMENT deposits straddle the steep-sided valley of Kicking Horse River at a point three miles east of Field, B.c., in Yoho National Park. The Monarch orebodies extend into Mt. Stephen on the south side of the valley, and outcrop at two points, 1,000 and 1,200 feet above the valley floor. The Kicking Horse deposits are in Mt. Field, on the north side of the valley, and they outcrop 200 feet lower.The East Monarch outcrop is said to have been discovered in 1884 during construction of the Canadian Pacific Railway. The larger West Monarch outcrop, 700 feet west of the original discovery, was not reached till 1917 because of its nearly inaccessible location on the cliff face.The Kicking Horse mine was staked in 1906. Little development was done for several decades, and mining was not commenced till 1935.At the East Monarch, mining was commenced soon after location, and several thousand tons of ore were shipped prior to 1912. At this time a gravity concentrator was installed. This was operated till 1924, and a total of 42,000 tons of ore were mined, including about 10,000 tons from the West Monarch. The period from 1928 to 1935 featured flotation milling and the mining of 265,000 tons of ore, mostly from the West Monarch orebody. Intensive exploratory development was carried out in both Monarch and Kicking Horse from 1935 to 1946. Production from both mines in this period totalled 380,000 tons. From 1947 to the time of closure in 1952, considerable new ore was found in both mines and 185,000 tons were milled. Immediate possibilities for finding ore in the Monarch were considered exhausted. Kicking Horse orebodies are known to persist with a low grade of zinc. Total production from the two mines amounts to 842,500 tons grading approximately 7 per cent lead, 10 per cent zinc, and 1.2 ounces per ton silver."

Jan 1, 1949

By Thomas T., Read

E DUCATION for the mineral industry was at first a single comprehensive curriculum, but it was early recognized that the main basis of mining is physics, while that of metallurgy is chemistry. The first school to offer curricula leading to degrees in mineral industry education in the United States (1853) had separate ones in mining and metallurgy. The Columbia School of Mines (the first really successful one) had only a single curriculum when it opened in 1864, but within a few years had so reorganized its work that it offered curricula in mining, metallurgy, geology, chemistry, and civil engineering. Interest in the metallurgy or geology curricula was slight at first, and for the next 30 years the great majority of Columbia students took the mining curriculum, probably partly because it contained nearly as much geology as the geology curriculum, practically all the metallurgy, and most of the chemistry, and partly because of the degree awarded for it. Other schools kept their mining curricula equally broad, and as late as 1900-1910 men were graduating as mining engineers who were practically as well prepared to make geology or metallurgy their life work, as they were for mining. Gradually, however, the subject matter of mining geology and metallurgy became so enriched through research and development that separate curricula in them became worth while; their progressive development is the subject of another chapter. Mining curricula also began to be somewhat diversified, and schools in areas where coal mining was of outstanding importance began to offer options in coal mining, the earlier curricula having been chiefly aimed at metal mining. The petroleum industry began its meteoric rise about the same time as mineral instruction in this country, but little more of applied science attended its birth than had attended such ancient practical arts as copper and iron

Jan 1, 1941

By Robert L. Runkel, D. Kirk Nordstrom, James W. Ball

Low-flow reactive-transport processes in Wightman Fork downstream of the Summitville Mine, south-central Colorado were simulated using the OTIS and OTEQ solute-transport models. The simulation was calibrated using data from a synoptic study conducted during October, 1998. Discharge over the 8-km reach from just below the mine site to the Alamosa River confluence ranged from 0.077 to 0.17 m3/s; travel time was 10.7 hours; pH ranged from 4.6 to 5.7. Simulations revealed that mass balance for SO4 was maintained, and that pH, Fe, and Al were non-conservative. Simulations allowing hydrous ferric and aluminum oxide or hydroxysulfate precipitation matched observed water quality conditions more closely than simulations without precipitation.

Jan 1, 2000

By C. P. Broadbent

The process metallurgy of many nickel laterite smelting operations is controlled largely by the physical chemistry of the slag system. Consequently, accurate phase diagram information and physicochemical property data are essential to interpret and predict the behaviour and optimisation of the overall process. The system (SiO2 - MgO - FeO) first described by Bowen et al. between 1914 and 1935 and the system (SiO2 - MgO - FeO - Fe2O3) determined by Muan and Osborne in 1956 are of particular relevance to the study of nickel laterite smelting slags as these systems form a reasonable approximation of many industrial slags. This paper will review the literature for these (and other relevant) phase systems. In addition data available from the ternary and (quasi)ternary phase diagrams will be compared with data obtained from industrial slags. The physico-chemical properties under consideration will include; melting and crystallisation behaviour (solidus and liquidus temperatures), viscosity - temperature relationships, heat flux considerations, electrical conductivity, surface and interfacial tension.

Jan 1, 1993

By E. C. Lane

[This is the tenth in a series of retorts on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee e end the Bureau of Mines of the United States Department of the Interior. The first report rave data on motor gasolines sold during .e winter of 1935-36.3/ The present report presents analytical data for 1,732 samples, representing the products of approximately 50 companies, which, as in previous surveys, include both lame and stall suppliers. In addition, the Pacific coast is represented by data that were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. he number of samples, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as follows: Regular price, 934 samples, 230 items, and 50 brands; premium price, 465 saris samples, 184 items, 40 brands; third-grade gasolines, 360 samples, 177 items, and of these terms as used in the surveys are follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.]

Jan 1, 1941

By Shabnam Sabah, Geoffrey Brooks

In oxygen steelmaking, splashing and droplet formation play a key role in the kinetics of the process. Though splashing has been studied by previous investigators, there is only limited understanding of how different cavity modes affect splashing. Therefore, a cold model study (at various lance heights and gas flow rates) has been carried out focusing on the issue of cavity modes and how it affects splashing phenomenon. Analysis using Fast Fourier Transform (FFT) was carried out on cavity oscillation that showed that frequency and amplitude of oscillation was highest in penetrating mode. Measurements of splashing over a range of conditions showed splashing greatly reduced when cavities went from splashing to penetrating mode. The results were validated and compared with plant data and previous model investigations.

Jan 1, 2014

By Jeff Gore, Jack Dermody, David Gribble, Brett Macaulay, Bart Sharpe, Paul Klaric, Paul Thornley, Ben DeVries

Optimal Fragmentation in Block Caving is difficult to achieve as it is generally defined by the rock mass itself and the way in which the cave is initiated. The lower portion of the cave has even less chance as the material has little time for self comminution. Blast Preconditioning of the Block Cave is designed to engineer the lower section of the rock mass to produce material of a suitable size to assist in the initial cave propagation and improve initial drawbell productivity. At Cadia East a plan was developed to drill 150-metre long, vertical up-holes from the undercut level and blast them fully confined to produce fractures in the rock mass. The blast itself was a simple undertaking. However, in the year preceding the first production blast, all aspects of the process were designed, tested and refined across multiple trials. As this type of challenging application had not previously been encountered in Australia there were many unique situations to address. Products and systems had to be developed and adapted to overcome these challenges. These included: Formulating and manufacturing an explosive that is robust and of a high VoD; designing and manufacturing easy to use electronic initiation systems; and, designing pumping systems to combat high head pressures to allow for successful and safe loading of the holes. Close collaboration with the customer ensured that the trials culminated in successfully blasting a hole containing almost 3.3t of explosive. These trials have since led to the blasting of four holes instantaneously, which contain almost 13t of explosive. This paper describes the various components of the system, the challenges and the final result.

Jan 1, 2013

By Dean Nichols, Matt Ortel

Explosive accidents in the United States have brought increased attention to emergency operation plans (EOP) at all facilities that manufacture, transport, or store hazardous materials – particularly explosive materials. Explosions are sudden, powerful, and complex events that are difficult to characterize in terms of the thermal, over pressure, and debris effects. Industry, regulatory, and public officials require emergency response planners to not only anticipate the blast effects of an explosion, but also to prepare an appropriate response.

Jan 1, 2016

Various influences determine how an Environmental Management System (EMS) for a mining or petroleum project is developed and administered. These influences include the environmental and resource legislation applying to the project, the culture of the organisation, the environmental sensitivity of the area, and the administrative policies of the regulatory agencies involved. While financial penalties and even imprisonment may be imposed for non-compliance with environmental legislation, there are other compelling reasons for the establishment of an effective EMS. If a company wishes to be considered by Governments for the grant of exploration or mining rights, it is important that it can demonstrate environmentally responsible operations at existing facilities. The development of an effective EMS requires commitment from the Board of the company and the issue of an Environmental Policy to empower all levels of the staff and workforce to achieve environmentally responsible operations. This must be supported by the provision of appropriate human and financial resources, and environmental training of staff at all levels from the Board to the mine site, workshop and office. A regular environmental auditing programme is essential to ensure that the EMS is in place and is effective in achieving compliance with regulatory requirements, corporate policies and protection of the environment. An EMS can be developed on the basis of existing management systems, quality management systems, existing and emerging environmental management standards (such as BS7750 and ISOI4000), or sophisticated computerised systems which may incorporate international experience, standards, and codes of practice.

Jan 1, 1995

By D Newton

The Mt Morgan Minesite in Central Queensland has been subject to both underground and surface gold mining operations since the late-1800s. The site is largely unrehabilitated and poor quality surface run-off and subsurface leachate is contaminating the nearby Dee River. The site is dominated by a large open cut, which now stores contaminated surface and subsurface run-off. Three models were used to simulate the complex hydrologic processes occurring at the Mt Morgan Mine: a rainfall-run-off model, a groundwater model and a storage behavioural model. Study results showed that the open cut is filling with water and will soon spill large volumes of highly polluted water to the Dee River on a regular basis if no remedial action is taken. This will result in a three-fold increase in pollutant load to the Dee River. Based on a consideration of water quality and quantity it was concluded that the first priority for future minesite water management should be the prevention of spills from the open cut. Potential management options to achieve this objective included surface rehabilitation, catchment diversions, modification of the pump-back system and controlled releases to the Dee River during floods. However, assessing the relative effectiveness of these measures required a thorough understanding of the complex surface and subsurface hydrology of the site. The results of a 100 year simulation of hydrologic processes revealed that previously favoured management options would be ineffective in preventing spills to the river. On this basis, a continuous treat and release strategy was proposed as the only reliable method of preventing future spills. The results of this study demonstrate that good environmental management decisions must be based on an understanding of the relevant physical processes and consideration of cumulative effects over an appropriate time scale.

Jan 1, 2003

By Albert F. S. Seboukens

A 5;6 MVA pyrometallurgical demonstration-scale pilot plant was commissioned at Mintek, South Africa, in 1994, using lead blast-furnace slag and coke as raw materials. The plant included a.d.c. power. supply, two plasma-arc furnaces' and an ISP lead-splash condenser. Slags containing typically 12 per cent zinc oxide and 3 per cent lead oxide are produced as a waste during the smelting of lead in a blast furnace. These slags are a potential: resource for the recovery of lead and zinc. During 1994, about 600 t of lead blast-furnace, slag was proceced through the pilot plant using the Enviroplas process. Zinc and lead oxides were reduced to their respective metals, volatilized, and collected in an. ISP lead splash condenser. Prime Western grade zinc and slags disposable in accordance with current US legislation, were produced. Zinc condensation efficiencies of about 80 per cent were achieved.

Jan 1, 1995

By G. Bonifazi

Certain deposits of incoherent materials which are near the surface and exploitable by open-pit mining may be characterized in real time before they are mined through an analysis of ground-surface imagery. If the slice to be stripped is not overly thick, in fact, surface texture and color properties may be extrapolated to its entire thickness. Image analysis techniques to process ground surface images acquired in situ (or in the laboratory shortly after their acquisition) which yield pattern vectors representative of RGB color component distributions and HSB texture parameters have been developed. The techniques were applied to a mineral sandy ore deposit containing three different lithotypes. Geostatistical analyses showed that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multi-barycenter classification algorithm. Such in situ image-analysis procedures open the way to the proper selection of the ore to be mined, or the proper way for run of mine (r.o.m). processing, or the appropriate blend to be processed before or at the same time as the mining process itself is enacted.

Jan 1, 1999