Search Documents

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010

By D. P. Goodall

THE development of the oil and gas resources of Western Canada is not, as many suppose, a new industry. For more than half a century an intensive search for these valuable products of nature extended from near the western edge of the Precambrian Shield to the Pacific coast, and from the International boundary north to the Arctic circle. The chief centre of interest to the oil prospector has, however, always lain in that region lying east of the first range of the Rocky mountains and confined largely within the boundaries of the Province of Alberta. Although there are many geological problems yet to be worked out in this Province, the oil-well driller has helped in no small way in determining sub-surface conditions and distribution of rock formations. The chief geological conditions as they affect the drilling of wells are generally re-cognized, and for this purpose the Province may be partitioned into three main divisions: first, the disturbed belt or foothills region extending along the eastern edge of the Rocky mountains; second, the Alberta geosyncline, a broad trough lying to the east of and parallel to the disturbed belt and from which the formations rise eastward to level off and form, third, the plains ? ? region, extending over the rest of the Province. A relatively small area in the northeastern part of the Province is underlain with Precambrian rocks and may be excluded from this classification, as it is of no interest to the oil prospector. The foothills, or disturbed belt, has presented the greatest difficulty to drilling, though it has produced the largest yield of oil within the Province to date. Within the foothills belt, the rock formations consist largely of hard shales interspersed with layers of abrasive sandstones, which wear out drilling bits at an alarming rate. The strata, in most flaces, dip steeply and are cut by numerous thrust faults. Although some o the faults have great displacements, their presence may easily be overlooked or the extent of the fault misinterpreted. Many a prospect well has been located on what appeared to be a suitable geological structure only to find, after drilling through a normal succession of rocks for 4,000 feet or more, that the drill had passed through a major fault plane to a younger formation than that in which drilling was started. Only a repetition of formations already drilled could be expected at greater depths.

Jan 1, 1942

By Marc C. Bétournay

Hydrogen fuelcells are a known technology, having been applied to stationary (e.g equipment, buildings, power plants) and vehicle applications (e.g transit buses, space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and green house gas emissions. To date, however, fuelcells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuelcells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuelcell type of choice for the industry, the Proton Exchange Membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk. A small fuelcell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, INCO, the Ontario Ministry of Labour, Sandia National laboratories and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter as well as from shock and vibration provided to the unit in underground conditions, at INCO?s 175 Orebody minesite and INCO?s Stobie Mine. The test results provided will show that the unit was not affected by the underground conditions: physically and electrically the unit performed without any reduction in operation or adverse effects imposed.

May 1, 2003

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By A. Gülmez

The complex ore deposit containing fluorite, barite and bastnaesite minerals is located in Beylikova Region of Sivrihisar town of Eskisehir Province of Turkey. The ore contains 40.80% CaF2; 35.35% BaSO4; 2.01%Ce; 1.5% La; 0.39% Nd and 0.1% Th. Barite recovery from this ore by flotation of the HCl leached tailings is presented in this paper. Rare earths are recovered by leaching. The leached residue (tailings) containing fluorite and barite is subjected to froth flotation to recover barite. The effect of pH and collector concentration on the flotation of barite have been studied in this work.

Sep 1, 2012

By S Henderson

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Microprobe analyses.of sphalerite grains from the Waitangi deposit mostly range from 0.8 to 1.5 mole % FeS, although one sample contains 9.5 mole % FeS. Arsenopyrite from Waitangi yields a range from 33.1 to 34.6 atomic As (%). There is no discernible correlation between the FeS content of sphalerite and gold grade in the Waitangi deposit suggesting that gold deposition is probably not controlled by changes in temperature and activity of sulphur aS2 that control the FeS content of sphalerite. The possible causes for gold deposition are thought to be boiling, mixing and changes in pH. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-ehalcopyrite samples yield a narrow range of d34SCDT values (-1.0 to 0.9 ë;n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source. However, the source of light sulphur in the late pyrite grains is not known. Preliminary fluid inclusion+studies indicate homogenisation temperatures between 173¦ and 284¦C and salinities of 0.23.0 NaCI equiv. wt % (uncorrected for C02). Vein quartz at Waitangi yields d18OSMOW values from 6.8 to 12.7 ë (n=23). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1-5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in d18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that d18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1993

By R. K. Kandasami

"Naturally occurring geomaterials such as sandstone, limestone and other soft rocks, residual soils are composed of a particulates held together through a cohesive matrix, usually composed of argillaceous or siliceous cementing agents. Geo-materials such as these have been reconstituted in the laboratory using ordinary Portland cement in lieu of the naturally occurring cohesive matrix, in addition to using sand particulates. This cohesive frictional granular ensemble is an ideal model material for understanding the mechanical behaviour of transitional geomaterials such as soft rocks. An important consequence of this cohesion that pervades the inter particulate system is the enhanced tensile strength when compared to a purely granular ensemble. The assessment of strength of these soft rocks and cemented sands is often understood in the framework of continuum mechanics, i.e. considering the cemented sand to be a continuum, and performing simple elemental tests such as uniaxial compression or tension tests. A simple model to describe the behaviour of these cemented sands has been to use elements such as springs, sliders, and dashpots in parallel to describe the existence of a cohesive and frictional component of strength (Jiang et al. 2007). In the framework of continuum mechanics, the mechanical response of these cemented sands have been modeled using traditional plasticity theory, for example utilizing variants of the traditional Mohr Coulomb model, Modified cam clay (Sun and Matsuoka 1999) etc. The typical sand models are amended to include the effects of cohesion, as proposed by Lagoia and Nova (1995).The mechanical response of cemented sands is understood to be transitional to the behaviour of a typical particulate assemblage and a quasi-brittle material. However, the effect of length scale in these material systems has not been investigated. This paper presents a series of uniaxial compression experiments conducted on weakly cemented sand specimens of various sizes. The effect of length scale in these weakly cemented sands is investigated through unconfined compression tests."

Jan 1, 2015

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Cristiane Ericksson, Ananda Scomazzon, Irineu Schadach, Juliano Tonezer

The state of Rio Grande do Sul, southern Brazil, appears on the national and international scene as an important producer of precious stones and the main gems are amethyst, citrine and agate. However, despite the immense potential of this mining activity, the extraction and processing of gemstones in Brazil present critical issues of infrastructure, which prevents a better development of these activities. In general, local production is still concentrated in small rudimentary mining. Recently some of these mines have begun to regularize their activities, in conjunction with the National Department of Mining Control. Besides these problems best practices for extraction activities and environmental control are not usually observed. Another problem which is placed in a critical way is the absence of aggregate value for the products of small mines. In this situation, the miners have great problems to obtain access to technology and adequate infrastructure. In most cases miners need negotiate their gems without processing, transferring most of the profit to intermediate traders. These results in heavy losses for the producer and for the communities involved. Given this scenario, the present study aimed at defining systems technically and operationally viable to be implemented in these communities in order to add value to gemstones. In this study best practices to thermochemical coloring systems, analysis of effect of raw materials and operating parameters on the final color of the gem were analyzed with attention.

Jan 1, 2014

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By S. Kelebek, E. Yalcin

"Diethylenetriamine (DETA) and/or triethylenetetramine (TETA) are reagents that can generally be categorized under ""flotation modifiers"". These polyamines are known to be effective for the deactivation/depression of pyrrhotite that is present in Canadian nickel-copper sulphide ores in large quantities. Recent bench scale testing on some of these complex ores indicated that chalcopyrite flotation can also be adversely affected under certain conditions involving polyamines, which may be taken to be an evidence of their specific affinity towards chalcopyrite. In general, DETA shows no significant depressant action on chalcopyrite while TETA's promotion of hydrophilicity for this mineral has been observed even in the presence of xanthate. This prompted an investigation on thermodynamic equilibria involving these polyamines and copper ions. Results serve a useful purpose to identify conditions for deactivation phenomena. CuDETA2+ and CuTETA2+ chelates as products of sequestration have large predominance areas covering a wide range of redox and pH conditions, where copper xanthate species are not stable, especially in the presence of TETA."

Jan 1, 2009

By M Qiao, A Sugden, W Zong, J Hines, J Roberts, T Ren

Long-term exposure to respirable dust continues to present an occupational health and safety hazard to mine workers in underground mines. Workers who are exposed to mine dust can develop occupational lung diseases including coal workers’ pneumoconiosis (CWP) or ‘black lung’, progressive massive fibrosis (PMF) and chronic obstructive pulmonary disease (COPD). To demonstrate the exposure impact of certain working conditions and improve dust management in longwall development panels, this paper details the development of a computational fluid dynamicsvirtual reality (CFD-VR) based training tool. The tool has been developed as an educational platform to facilitate the effective communication of workplace health and safety (WH&S) dust control measures for continuous miner operators and engineers. The study introduces a promising approach to model ventilation and dust flow patterns based on site-specific data, employing computational fluid dynamics (CFD) for a detailed analysis and visualisation of these mechanisms. Additionally, an algorithm has been developed for processing the large and complex CFD data sets into a form amenable for visualisation within a virtual reality (VR) environment using standalone VR headsets with limited processing power. This training tool has been deployed to mine sites with the specific purpose of educating users on the hazards of dust emissions and the best practices for control.

Apr 16, 2024

By W. C. Smith

Even with conservative mine planning, rib instability can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation. sporadic zones of progressive rib instability were detected that culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1991

According to the Australian Bureau of Statistics, fatalities from road transport accidents represented an average of over 97 per cent of all transport related accidents between 1997 and 2002. With increasing traffic density, tunnels are becoming a more viable means of providing alternative travel routes to ease areas of congestion in the road transport network. However, unlike open road conditions, a fire incident in the confined space of a tunnel environment may impact upon many users that are remote from the incident location. In this context, designing for an appropriate level of safety in tunnels is therefore an important consideration for achieving consistency in the life safety measures for users of the road transport network. Unfortunately, like fire safety engineering design for buildings, there are presently no clear measures in the design processes to assess the adequacy of the design in terms of attaining the level of safety implicated in the design objectives. This is partly due to the indeterminate nature in which the design objective or the level of performance measure is stated û the intent of the objective is relatively clear but the measure of it is not. Another reason is the lack of a standardised procedure for determining the critical design variables affecting life safety. This is important to ascertain consistency in the use or adoption of the important parameters for design. This paper looks at the processes involved in the fire engineering design of road tunnels that are currently practised. A review of the design processes for fire safety in road tunnels is provided, which includes the range of fire scenarios in a tunnel environment, the traffic flow and composition, the relevant fire protection systems, the ventilation and smoke control system, the egress provisions and the benefits of incorporating fire brigade intervention. A simplified risk assessment approach is developed for a typical road tunnel to assess and evaluate the impact of a range of design parameters on life safety. Using a sensitivity technique, the important variables are then identified and means of reducing design variations associated with them are recommended. The technique may be further refined for use in the development of codes or guidelines in order to develop a suitable means of deriving more consistent design values, and hence achieve better consistency in the overall level of safety in the design.

Jan 1, 2008

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)- based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jan 1, 2024

By Thomas T. Read

IN reviewing the field of mineral industry education last year reference was made to recent assertions, mostly emanating from sources not in a position to know the facts, that mining engineers as a class are disappearing. Attention might also then have been called to a statement that appeared in Engineering News, August 11, 1892 (p. 130), ". . . the great absolute decline in number of mining graduates, which last amounts almost to a complete abandonment of mining engineering as a distinct branch of study." Evidently we outrank opera stars in the number of farewell appearances we are able to make; 43

Jan 1, 1936

By Shengli Wu, Fengjie Zhang, Feng Chang, Hua Lu, Kaiping Du

In order to make a complete understanding of steel plant metallurgical dusts and to realize the goal of zero-waste, a study of their properties was undertaken. For these purposes, samples of two sintering dusts (SD), two blast furnace dusts (BFD), and one electric arc furnace dust (EAFD) taken from the regular production process were subjected to a series of tests. The tests were carried out by using granulometry analysis, chemical analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy via SEM (EDS), and Fourier transform infrared spectroscopy (FTIR). The dominant elements having an advantage of reuse are Fe, K, Cl, Zn, C. The dominant mineralogical phases identified in sintering dust are KCl, Fe2O3, CaCO3, CaMg(CO3)2, NaCl, SiO2. Mineralogical phases exist in blast furnace dust are Fe2O3, Fe3O4, with small amount of KCl and kaolinite coexist. While in electric arc furnace dust, Fe3O4, ZnFe2O4, CaCO3, CaO, Ca(OH)2 are detected.

Jan 1, 2015

By Hojong Kim, Isehaq Al-Nafai, Kwadwo Osseo-Asare

The standard Gibbs free energy of formation (ΔGo f, 298) of bastnasite, (Ce, La, Nd, Pr)FCO3, was estimated using four different methods. The obtained average values were − 1589.5 kJ/mol for CeFCO3, − 1599.5 kJ/mol for LaFCO3, − 1589.1 kJ/mol for NdFCO3, and − 1595.4 kJ/mol for PrFCO3. The value for cerium bastnasite, CeFCO3, was used to construct a potential vs. pH (Eh-pH) diagram to investigate the stability relations of cerium bastnasite. The diagram shows that CeFCO3 is stable in neutral to basic conditions (pH ~ 6.5–11).

By Ben E. Lindsly

The study of "bottom-hole samples follows in natural sequence the study of samples obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1930, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs.. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, That physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing Tells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental data were obtained in the study of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at higher pressure, and later became mixed with the original undissolved gas.

Jan 1, 1933