Search Documents

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The earliest industrial application of high pressure grinding rolls (HPGR) at comminution was in 1984 in the cement industry. Since then, the equipment has been widely applied in mining activities. Despite the rapid spread across the industry, several challenges are still present in the equipment’s application, especially considering the complex ore breakage behaviour reported for this process. The pellet feed’s HPGR comminution was recognized as fundamental to efficiently increase the particle surface area (e.g., blaine specific area, BSA) at a lower energy and water consumption level (Chapman et al. in J Southern Afr Instit Mining Metall 113:407–413, 2013). The present study considers a novel milling process applying only HPGR as a re-regrind stage after concentration. The amount of successive ground product recirculation into the machine to achieve the required particle size for the pelletizing process was investigated. The study compared the ball wet milling process with the innovative processing technology for hematite–goethite ores. Green pellet balling and induration processes were simulated in bench and pilot scale. The milling results showed a considerably steep increase in BSA after each recirculation step into the HPGR, although compared with the ball-milled product the size fraction <45 μm% increased a modest five percentage points after three recirculation cycles, remaining steady until the last recirculation step. As a result, the green pellet generated presented higher concentration of pellets between 10 and 16 mm (%10-16 mm), with a higher drop number than typically observed when produced with ball-milled feedstock. Consequently, on the induration process, a higher pellet deformation was observed during the pot grate loading. Despite that, the fired pellets still presented an outstanding performance in cold crush strength (CSS) considered suitable to an industrial application.

By B. Mather

I was very glad to see an article on alkali-silica reactivity of concrete aggregate in Mining Engineering. It is a topic that should be reexamined every 45 or 50 years. The last paper (that I am aware of) that examined this topic in Mining Engineering was Rexford (1950), who, at the time, was chief of the Petrography Section, South Pacific Division Laboratory, Corps of Engineers, Los Angeles, CA. The paper was presented at the AIME meeting in Los Angeles in October 1948. Professor Leming&apos;s discussion generally reflects the current state-of-the-art; but it provides no references for more detailed information. I wrote a paper titled "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," which was included in the Proceedings of the Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams (Mather, 1995). In it, I emphasized that it was the hydroxide ion (not the alkali ion) that caused the pore fluid in the concrete to dissolve reactive silica, producing alkali-silica gel capable of taking up water, thereby, causing swelling and rupturing of the concrete. Excessive expansion will not occur unless there is a sufficient amount of potentially expansive alkali-silica reaction product and water. However, this will not occur unless there is a sufficient quantity of reactive aggregate and unless there is a mechanism by which the pH of the pore fluid can get well above the normal value of about 12.6. In many cases it is sufficient that the cementitious medium not only contains portland cement but also contains ground granulated blast-furnace slag (GGBFS) or a pozzolan such as fly ash, silica fume, metakaolin, volcanic glass or calcined shale - any of which may have been included for economic reasons. If, however, the person selecting the ingredients for concrete knows that the aggregate is reactive (with no alternate nonreactive aggregate available) and if the person knows that the only available portland cement has a high alkali content (i.e., more than 0.6% Na2O.; Na2e = % Na20 + 0.658 x % K20), then it becomes irresponsible not to establish what reasonable precaution one should take. Professor Leming suggests using one of the following: 30% Class F fly ash, 50% GGBFS or 7% to 10% silica fume. My view is that one should prepare test specimens with the cement and aggregate to be used and then expose these both with and without at least two dosages of each of the various alternative materials (slag, pozzolan and lithium salts), so that the required dosage. to control the expansion is established. Then, economic considerations can dictate the final selection. I would point out to the author that GGBFS is not a pozzolan and is not an admixture, but, rather, it is a latent hydraulic cement. An admixture is, by definition, a material other than hydraulic cement. I commend him for suggesting that aggregate producers should become more active in knowing about the reactivity of their products and the precautions needed to permit those products to be safely used in concrete.

Jan 1, 1997

By Galymzhan Karamyrzayev, Rashid Nadirov

Zinc ferrite ( ZnFe2O4) is a by-product of non-ferrous metal production and is considered a promising source of raw zinc. The most efficient way to extract zinc from its ferrite is via acidic extraction, specifically leaching by hydrochloric acid. A comparative study of synthetic zinc ferrite hydrochloric acid leaching in isopropanol, aqueous, and the mixed solvent was performed. Zinc ferrite was obtained by sintering a zinc and iron (III) oxide mixture. Crushed samples were subjected to leaching in 1 M HCl at 323, 333, and 353 K and pulp density of 1 g/100 mL. The dissolution of zinc and iron into solution in organic media reached 77% at 353 K, while in an aqueous environment this value was 65%. The activation energy of 70.0 kJ/ mol was found for the leaching process in an isopropanol environment, which is lower than that in an aqueous solution by 15%. The more efficient leaching effect of isopropanol is attributed to the lower dielectric constant of the alcohol which increases the affinity of chloride anions for zinc and iron cations at leaching.

Jun 5, 2022

By John B. Hastings

THE occurrence of such a large amount of gold in the Hartsel granite, even though the surmised existence of similar areas is not new, brings freshly to mind the pegmatite type of magmatic differentiation lately brought again to attention by occurrences at Silver Peak, Nev., described by Spurr; and in Alaska, described by both Spurr and Brooks. In both localities graunitic rocks or dikes are thought to pass into metalliferous quartz-veins. An interesting association in this connection is the occurrence of diamonds in residual pegmatitic clay of San Juao de Chapado, Brazil, described by Derby :1 (P. 142) "Bodies of pegmatite are quite common in the older rocks of Brazil, both in the. diamond regions and elsewhere, occurring not only in the gneiss and granite, but in the schistose series as well. Those that have been examined are dike-like in their mode of occurrence and granitic in composition." (P. 143) "The question of the eruptive or secretionary origin of pegmatites has long been a subject of discussion among geologists. . . . The recent studies . . . seem to have clearly established that most if not all of them are essentially eruptive masses, though possibly modified in some way by aqueous agencies. Even before becoming acquainted with the literature of the subject this view had seemed to me to be the only acceptable one as regards the typical pegmatites of Brazil." What is pegmatite ? J. F. Kemp says ". . . veins or dikes-it is an open question which is the more correct term-are met formed of very coarsely crystalline aggregates of the same minerals that constitute granite. These are called pegmatite and in them is the home of graphic granite, the curious intergrowth of quartz and feldspar, such that a cross fracture of the blades of quartz suggests cuneiform characters. . . . In regard to the larger veins or dikes it seems improbable that true igneous fusion could have afforded such coarsely crystalline aggregates, and so we are forced to assume such abundance of steam and other vapors, i.e, mineralizers, as to almost, if not quite, imply solution."

Jan 5, 1908

By Rob Farnfield, Ben Williams

The A5 road in the United Kingdom forms an ancient and well-used route through the hills and mountains of North Wales. In the 1990?s a programme of work was conducted to upgrade the road to modern standards. As part of this work a new cutting was constructed to bypass a portion of road routed through a gorge close to the village of Ty Nant. This new cutting was formed by drilling and blasting and included much pre-splitting and extensive rock bolting. This operation caused much concern to local residents relating to vibration, air overpressure and flyrock.

Jan 1, 2011

By Weijie Wei, Jinwang Zhang, Shengli Yang

Due to the unbalanced top coal drawing process, the recovery ratio is low, and the equipment stability is poor in the longwall top coal caving mining (LTCC) with an inclined seam. Aimed at these problems, this paper proposes the dynamic group caving method (DGCM). The basic procedure is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Taking the panel no. 8103 in Beixinyao mine as the research object, the characteristics of drawing body shape, particle movement trace, and variation of recovery ratio are investigated by using Particle Flow Code. Furthermore, the effect of mining-caving ratio on the top coal drawing law under DGCM is revealed by the simulation results, and compared with the single-opening sequence caving method (SSCM) and the doubleopenings sequence caving method, advantages of DGCM are determined in inclined seams. The results show that the drawing body can be divided into the left and the right under DGCM. Specifically, the drawn top coal particles in the left are from the upper part of this support, that in the right are from the lower part of next support, which verifies the correctness of the theoretical analysis. The characteristics of the drawing body shape are more significant when the mining-caving ratio is relatively small. In addition, with increasing mining-caving ratio, the recovery ratio of the panel both increases gradually underDGCMand SSCM.When the miningcaving ratio is less than 1:1, the recovery ratio of DGCM is obviously higher than that of SSCM, indicating that DGCM can greatly improve the recovery ratio. While when the mining-caving ratio is larger than 1:1, the recovery ratio of two caving methods is basically equal; however, the advancing time is significantly shortened under DGCM. This study are of great significance to realize high efficiency and precise caving in LTCC with an inclined seam.

Jul 7, 2020

By Karl S. Vorres

Coal my not seem like it, but it is a perishable commodity. The basic coal scientist cannot always replicate earlier experiments with a given sample because of changes that have taken place in the sample. This has led to a stated need for stable samples Coal looks like a uniform black solid to many people, but it does vary in its composition from state to state and mine to mine it also can be shown to vary significantly within a mine or seam. These variations have led to a stated need for consistent samples.

Jan 1, 1985

The tragedy of the Moura No. 2 incident has lost much of its emotional mileage for those organisations that thrive on loss and suffering. However, for the families, workers, mine owners and operators in the Queensland underground coalfields, the challenge of delivering a positive outcome, though well underway, is in its infancy. The pressure created by interested parties is necessary for overcoming the inertia involved in change; but they cannot deliver the change. The responsibility ultimately resides at each individual minesite with the people who work there each day.

Jan 1, 1998

By Mariana Barcelos, Frederico Muylaert Margem, Giulio Rodrigues Altoé, Pedro Amoy Netto, André Gomes, Sergio Neves Monteiro

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of polyester matrix composites reinforced with continuous fique fibers, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Jan 1, 2015

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

By John H. Wright

The United States Antarctic Program (USAP), through its principal support contractor Raytheon Polar Services Co. (RPSC), has recently completed a three-year project comprising nearly 936 m (3,071 ft) of undersnow utility tunnels at Amundsen-Scott Station, South Pole, Antarctica. The tunnel serves the new station facilities that are currently under construction. It houses the piping that conveys fresh water from current and future water well sites, as well as waste water to repositories in abandoned wells. The undersnow tunnels permit year-round access for system operations and maintenance. The network of tunnels is entirely unlined and unsupported. And, for the most part, it maintains a rectangular cross section of 1.8-m-wide x 3-m-high (6 x 10 ft).The tunnel runs from 6 to 14 m (18 to 45 ft) below the surface. Eight 1-m- (3.3-ft-) diam raises bored from the surface serve the network as emergency escapeways.

Jan 1, 2002

By G. L. Oldright

The data presented in this paper were collected et the smelter of the Consolidated Mining A Smelting Co. of Canada, Limited, Trail (Tadanac), British Columbia, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent, George Murray, assistant smelter superintendent; and the staff members listed in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth4 dealing with blast-furnace gases.

Jan 1, 1934

By J. W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct iron making pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicate that 69% are less than 2.5 µm across, 21 % are 2.5-5 µm, and 10% are larger than 5 µm. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By G. J. Arseneau

Mineral resource statements are reported as tonnage and grades. While great care is placed on generating a reliable estimation of grade, the determination of bulk density for resource estimation is often overlooked. Often mineral resource statements are prepared using a simple average value of bulk density. While a simple average estimate of bulk density can be appropriate for some deposit types, an over simplistic estimation of bulk density can result in serious errors in tonnage estimates and consequently to an over or under estimation of metal content. The construction of a reliable bulk density model requires an adequate bulk density database in order to develop a good understanding of the variability of bulk density with grade and geology. A reliable bulk density database is also essential in determining the appropriate modeling technique to minimize the errors in mineral resource statements caused by incorrect bulk density determinations. This paper summarizes bulk density measuring techniques and draws on examples from various deposit types examining the basic principles of bulk density modeling and domain construction for each deposit type. Examples are presented of simple bulk density domains and more complex grade variable bulk density domains with a discussion of best approaches for minimizing errors in density estimation.

Aug 1, 2013

By Pinn N

Geosynthetics is an all encompassing word to describe a number of man-made products usually from hydrocarbons which are used in conjunction with the soil. The specific products are:Geotextiles Geomembranes GeonetsGeogrids GeocompositesIn mine establishment and associated construction work, Geosynthetics have proven to be successful in a wide range of applications. For example, geotextiles are now used to assist with the establishment of access roads, site preparation, haul roads and in connection with the construction of embankments for storage ponds and dams as well as for general hydraulic and foundation engineering problems.

Jan 1, 1990

By H. Rush Spedden, A. M. Gaudin

IN the belief that a critical study of its operating problems might be a sound investment, the Cuban American Manganese Corporation initiated an ore-treatment research in cooperation with the Massachusetts Institute of Technology. One of the early objectives of this research naturally became the relationship of the microscopy of the Cuban ores of the Corporation to their flotation treatment. The operations in Cuba have already been described by F. S. Norcross, Jr.7 and the laboratory study of manganese oxide flotation goes back a number of years .4 Broadly speaking, the difficulties encountered in the flotation of manganese ores are that the consumption of reagents is extremely high, the concentrate contains more silica than is desirable and the tailing losses are relatively high. An appreciable betterment on any of these scores would achieve a definite betterment in costs, quantity of minable ores, and quality of product. The microscope study discussed in this paper was made on samples from the Quinto mine, from the Ponupo mine, and from mill products at various stages of passage of the ore through the mill. The writers have had access to Company records and in particular to the petro¬graphic studies made on thin sections of ore by the late Professors R. J. Colony and Philip Krieger, of Columbia University. They acknowledge their debt to both of these men for the help derived from the reports. Manganese oxides are black, friable, smudging. It is, therefore, very difficult to judge operations by inspection. The mineralogy of manganese compounds seems to be confused, and the authors believe that many more minerals have been described than actually exist. Much of this difficulty is due to the prevalence of the structural conditions that will be discussed further in this paper; namely, the porosity and the friability of the ores, and the extremely intimate association of minute manganiferous mineral crystals with impurities of various sorts. By all odds the most important manganese mineral in Cuba is the one that in this paper is called "psilomelane." The name "psilomelane" has been used in so many different ways that the choice of it for this ore may not be approved by all. However, it seems to be the best under the circumstances. This mineral accounts for about 97 per cent of the manganese in the ores of the Quinto and Ponupo mines and in the mill feed. The remaining odd 3 per cent consists mostly of pyrolusite together with minor amounts of other manganese oxide minerals. DESCRIPTION OF PSILOMELANE Aggregate Structure In grains or lumps, psilomelane has a characteristic fibrous appearance and seems

Jan 1, 1942

By Konstantinos Salonitis, Joanna Mielnicka, Mark Jolly, Arun Prabhakar

Lead sheets are widely used for roofing applications, radiation protection and sound proofing. Most of the sheets are either produced by rolling cast slabs of lead sheets or via the direct method (DM) of casting of the sheet continuously. The DM method comprises of a rotating water-cooled drum that is partly immersed in a bath of molten lead and sheets are cast out continuously. The direct method of casting lead is more energy efficient compared to the rolling process which requires a casting process before rolling to achieve the required thickness. This work investigates the energy consumption in different stages of the DM process and suggests pointers for improvement. An energy audit of the process is conducted and the consumption is analysed at different stages and compared with rolled lead.

Mar 1, 2018

By Wi11iam M. Leaders

Uranium Recovery Corporation was incorporated in the State of Florida in 1968 for the sole purpose of developing a method to economically recover uranium from Florida phosphoric acid. The preliminary laboratory work culminated in the demonstration of the process to United Nuclear Corporation in the spring of 1971. This was quickly followed by a pilot plant program to identify any unusual problems such as those arising from the day-to-day variation which occurs in a fertilizer phosphoric acid plant production system. After two years of pilot plant operation, United Nuclear Corporation purchased controlling interest in Uranium Recovery Corporation and committed several million dollars to the design and construction of the first commercial plant for this purpose in the State of Florida, or anywhere else in the United States, for that matter. After many start-up problems were resolved at the production plant located at the W. R. Grace fertilizer complex near Bartow, sustained production began March, 1971, and has continued to date. We still have some problems to solve but are currently producing sufficient uranium to make shipments to the UF6 converters for preparation of Florida uranium for use in nuclear power plant fuel materials.

Jan 1, 1978

By Alcides Freitas

The great importance of aggregates as a basic building and maintenance material for both public and private projects makes the identification and availability of this valuable resource imperative for our economic and social well being. This was one of the main reasons that led the California Legislature to enact the Surface Mining and Reclamation Act of 1975 (SMARA). The Act requires the State Geologist to classify mineral areas in the state and the State Mining and Geology Board to designate mineral deposits of regional or statewide significance. What is the "Classification and Designation" process and how is it working?

Jan 1, 1984