Search Documents

By K. Barani, S. M. S. Ganji

Creatine was used as a lixiviant for gold dissolution from gold ore. The effects of creatine concentration, temperature, leach time, and pH were examined for their influence on extent of gold dissolution. The results show that at a temperature of 75°C and pH 11.5, gold dissolution increased from 51% to 88% on increasing creatine concentration from 25 to 50 g/t. Further increase in creatine concentration showed a negative effect on the gold dissolution. Gold dissolution increased from 47% to 87% by increasing the temperature from 25°C to 55°C, and from 61% to 89% by increasing pH from 10 to 11.5. Under the optimum conditions of solids’ content of 30%, pH 11.5, creatine concentration of 100 g/t, temperature of 75°C, and hydrogen peroxide addition of 2%, about 90% of the gold could be dissolved from the ore after 24 h. A comparison between creatine and cyanide leaching showed that 90% gold dissolution was achieved at a cyanide concentration of 300 g/t, which is three times higher than the creatine concentration under optimal conditions.

Apr 14, 2024

By W. B. Agocs

"IntroductionWITH THE DISCOVERY of natural radioactivity at the end of the 19th century, and the design of equipment for the detection of this phenomenon, radioactivity surveys bad their inception. Early in the 20th century it was found that almost all rocks are radioactive to a certain degree. This radioactivity is due to the nuclear disintegration of six naturally radioactive elements: potassium, thorium, uranium, rubidium, samarium, and lutecium.The radioactivity of these elements manifests itself by the emission of some concentration of alpha, beta, and gamma 'rays'. Of these, the alpha and beta 'rays' are, respectively, helium atoms and electrons, while the gamma 'rays' are short wave length x-rays generated in the nuclear disintegration by the transformation of mass into energy.The alpha and beta rays, being particles of matter, are stopped ve• easily by material barriers, but gamma rays are extremely penetrating and they will pass through a foot or more of rock or several inches of lead.The radioactivity may be detected by the causing of ionization by the radiation. The radiation detectors may be divided into four classes: ionization chambers, proportion al counters, and Geiger counters, all of which use gas for ionization, and scintillation counters, in which a solid is ionized. The basic principle of all these detectors is the same; the difference lies in the method used to measure the degree of ionization produced by the rays. Currently, the scintillation counter is displacing, the other instruments in radioactivity surveying."

Jan 1, 1955

By H. Dundar

An extensive testwork was performed around the HPGR plant at GoldFields Ghana Limited Tarkwa Gold Mine. The HPGR was used to prepare the feed for heap leaching. The circuit was configured in such a way that the edge material from the HPGR discharge was recycled for further crushing while the product from the centre reported to the heap leach section. The set-up of the Polysius HPGR provided an opportunity to study the effect of different design and operating variables. This paper will discuss the results from the tests performed to assess the effect of rolls? speed and applied pressure on the capacity and the grinding efficiency of the HPGR. Applying different pressure values appeared to have an influence on the amount of edge material recycled.

Jan 1, 2012

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

By Victor Nazimko

A new technique for reaming the holes has been tested. This technique is available for reaming a hole at its deep end creating an enlarged cavity that has helicoidal grooves oriented at less than 40 degrees to the hole axis. This technique increases bolt resistance by a factor 1.3-1.62; its bearing capacity by 3 times and enhances underground roadway stability. This technique is suitable for great depth (1000m and greater) and weak wet rocks.

Jan 1, 2008

By S. Mukai, Y. Shah, T. Zshikawa, T. Wakamtsu

In order to recover coal concentrate of low ash and low iron content, the electrostatic separation of coal was studied. It is more successful in the corona discharge field to recover the coal concentrate of low ash and low iron content than in the field without corona discharge. The effect of humidity on the electrostatic separation of coal was then studied. From the experimental results, it was clear that the electrostatic separation was excellent in about 60% relative humidity of atmosphere. Thus, the separation of vitrite from coal is practicable by electrostatic separation. In recent years the demand for high quality coal containing low ash, low iron, and low sulfur has increased. To fulfill this requirement, a higher grade coal concentrate must be produced. Study on the electrostatic separation of coal has been performed for several years in the author's laboratory. From the results of this research, it was considered that the behavior of coal particles in the electrostatic field relates closely to the ash and iron content in coal. In the present paper, the electrostatic separation of coal in corona discharge field was studied in order to recover the high quality coal concentrate and then the effect of humidity on the electrostatic separation was investigated. PREPARATION OF COAL SAMPLES The coals from the Akabira mine, the Kushiro mine, the Miike mine, and the Oshima mine which are famous coal mines in Japan were used in this study. The ash contents of these coals are shown in Table I. From the results of the analysis of the coal samples by the Norelco X-ray diffractometer, it is recognized that the Miike coal includes mainly pyrite, quartz, kaoline, calcite, and epidote; the Kushiro coal: kaoline, quartz, and montmorillonite, and the Oshima coal: siderite, dolomite, and other substances. For the preparation of samples, the coarse pieces of coal were crushed to about 2 mm in diam and then ground in an agator mortar. The ground products were sieved and fractions of 10 — 14 mesh, 14 — 20 mesh, 20-28 mesh, and 28-35 mesh were prepared, respectively. APPARATUS OF ELECTROSTATIC SEPARATION The principal part of the apparatus of the electrostatic separation used in the experiments is shown in Fig. 1. In order to generate the corona discharge field, a needle-shaped electrode combined with a pole electrode is installed as the high tension electrode. In the case of investigating the effects of the humidity on the electrostatic separation of coal, the needle-shaped electrode was combined with a plate electrode instead of the pole electrode as shown in Fig. 2. The pole or the plate electrode was installed to promote the repelling of the charged particles by producing the electrostatic field between this electrode and the grounded roller. It seems to be very useful on the coal separation to install these combined high tension electrodes. SEPARATION OF COAL PARTICLES IN CORONA DISCHARGE FIELD The separation testings on the coal samples in the corona discharge field were performed by the apparatus as shown in Fig. 1. These experiments were carried out under the following conditions: feed size 20 — 28 mesh, room temperature, normal humidity and applied voltage 15-20 KV, and the combined electrodes including the needle-shaped electrode were negatively charged. The results of these testings are

Jan 1, 1968

By P. M. Krishna

An example illustrates the use of ASTM Standard E901-82, Classification System for Uranium Resources. The example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that ,remain in fixing the classification of a given uranium resource include the uncertainty in estimating the quantity of undiscovered resources and resolving the differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1983

By S. H. Davis

THE pyrites used in making sulfuric acid in the United States have been largely imported from Spain and Canada, the Spanish imports amounting to nearly 1,000,000 tons per annum in the pre-war period. The greatly increased use of sulfuric acid and the cutting off of these Spanish imports, incident to war conditions, brought about a threatened shortage of sulfur supplies during the war period. The bituminous-coal mines of certain districts have, for many years, furnished a small tonnage of pyrite in the form of coal brasses. A mechanical concentrator at Danville, Ill., for a number of years, has been treating hand-picked lump pyrite and coal from the picking belt and from the mines and a small plant near Gillespie, Ill., for a few months has been recovering pyrite from washery refuse. Many mines throughout Illinois, Indiana, Western Kentucky, Ohio, and Pennsylvania have shipped an occasional car of the hand-cleaned lump pyrite. Only a very small percentage of the available pyrite has been recovered in this way, however, as usually the miners throw such lumps into the gob with slate and other impurities. It has been estimated that the western Indiana coal field could furnish more than 100,000 tons of pyrite per annum. The present production is very small. The possibility of furnishing the domestic trade with pyrites recovered as a byproduct from coal-mining operations appears attractive but there are certain features difficult to overcome. Pyrite, to be used in acid making, must meet with certain requirements as to size and purity. Lump ore for grate burners should be under 3 in. (7.6 cm.) and over 1 in. (2.5 cm.) in diameter. Fines for use in mecnanical roasters should be under quarter mesh. The material should be high in sulfur, free from arsenic and phosphorus, and as low in carbon as possible. The pyrite obtained from coal can be made to meet all the above requirements, but it is difficult to remove all the carbon. The pyrite in coal occurs as bands and nodules of varying thickness and size and of comparative purity, but mixed with this is more or less web sulfur. The web sulfur carries with it admixed coal, which may make the concen-

Jan 8, 1919

By AIME AIME

As already announced in the January Bulletin, this publication will be issued during the coming year monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates for membership, and other items of timely information. Spokane Meeting and Excursions. Further details of the 97th meeting of the Institute have been sent to members in the Circular of May 8, 1909. The list of those intending to go on the excursion is filling up, and since preference in position of state-room or berth is given in the order of application, members and guests who expect to accompany the party and have not yet communicated with Mr.. Theodore Dwight, 29 West 39th St., New York, N. Y., are earnestly requested to do so without delay. For convenience of the members a summary of the additional information is here presented. A special train of Pullman cars will leave Chicago about September 15. This train will be side-tracked at all places visited, and the sleepers will be available for lodging and the dining-car for meals during the entire trip, except during the Yellowstone Park tour. The general cost of the trip per member will be $300, which includes transportation, berth, and meals for the entire trip from Chicago back to Chicago, almost 6,000 miles, and the tour through. Yellowstone Park, occupying in all about 30 days. Special, accommodations on the train will be furnished at the following rates

Jun 1, 1909

By Hassan El-Shall, Rosana M. Macedo Borges, Ponisseril Somasundaran, Regis Stana, José Renato B. Lima, Patrick Zhang

The phosphate fertilizer industry is a large activity in Brazil because the soil has a phosphorous deficiency. The phosphoric acid that is produced is extensively used in the production of fertilizer. It is produced by reacting phosphate carbonaceous rock with sulfuric acid, generating phosphogypsum as a by-product. In 1991, there were about 29 million tons of phosphogypsum stored in Brazil. This has increased to an estimated 280 million tons in 2001. While the phosphogypsum is used in the cement industry and also in agriculture, the quantity used is much less than the production rate, and the stockpiles are still increasing. The radioactivity of this waste may not allow its continued use as a construction material and some other uses. However, Brazilian phosphogypsum contains a smaller quantity of radioactive materials than is reported for phosphate rocks from other countries. One important reason is the geological origin of the Brazilian apatite. All the large deposits being currently mined are igneous, not sedimentary, as is the majority of the phosphate rock produced around the world. An extensive study is being conducted to characterize the phosphogypsum generated in two production facilities in Sao Paulo state to develop safe uses for this waste and determine the environmental impact caused by the present method of phosphogypsum disposal.

Jan 1, 2002

By R. Hogg

"Particles play an important role in our environment and in many aspects of human activity. Much of the Earth's surface - sand, soil, rocks - consists of particles, as do clouds in the atmosphere, smoke from fires, and dust in our homes. Many of the foods we eat - cereals, flour, instant coffee - and everyday items such as pharmaceuticals, cosmetics, detergents and other cleaning products are encountered in the form of particles. Inks and paints consist of very fine particles dispersed in liquids. Modem agriculture uses huge quantities of fertilizers and pesticides, largely in particulate form. The list could be extended almost indefinitely; particle systems are obviously an important part of our daily lives. But what do we know about them? For most people, the answer is probably: not much.We are all familiar with the three common states of matter: gas, liquid and solid. In many respects, particle systems should be regarded as a distinct class of their own. The particles themselves may be solid but we all know that a heap of sand is quite different from a solid rock. A cloud of liquid droplets - fog - has much more in common with a cloud of solid particles - smoke - than it does with a bucket of water. There are certain characteristics and properties which are unique to the particulate state. The behavior of any particle system is determined not only by the material from which the particles are made, but also by interactions among the particles and with their environment. These interactions become increasingly important as the size of the particles decreases, and for exceedingly fine particles, smaller than about one micrometer (0.000001 meters or 0.00004 inches), these interactions dominate and we enter the realm of colloidal systems.Particle SystemsA system in which discrete entities - particles -are dispersed in a continuous medium can be regarded as a particulate system. The particles and the medium can consist of a solid, liquid or gas. The various combinations and some common examples are listed in Table 1. The properties and behavior of these systems depend on the characteristics of the particles, the nature of the medium, and the relative abundance of the two phases. In general, it is the latter which determines the kind of behavior exhibited by the system.As a general rule, the behavior of particle systems follows that of the dispersed phase (the particles) at high concentration, and that of the continuous phase (the medium) at low concentration. For example, both powders and smokes consist of solid particles in a gaseous medium. However, in a powder the solids typically occupy over one half of the total volume; in many respects powders behave like solids. In a smoke, on the other hand, the particles may take up only a few parts per million of volume, so that these systems generally behave like gases."

Jan 1, 1989

By S. J. Hubbard, S. D. Michaelson, A. W. Last, B. H. Ensign

Of the seventeen western states, five-Arizona, Utah, New Mexico, Montana, and Nevada-produce about 90 pct of this country's primary copper. All seventeen of these states occupy 60 pct of the nation's land area but receive only 25 pct of the country's total precipitation. Seventy percent of this precipitation returns directly to the atmosphere through evaporation and transpiration, leaving very little for ground reservoir recharge or immediate domestic, agricultural, or industrial use. With so limited a supply available for all, competition for water rights among users is severe. The result does not always permit using the limited supply to produce the most valuable end product. Most of industry and much of agriculture can shop around for suitable operating locations. Where water is critical to their purposes, they can and do locate in areas where the needed amounts are available. Such is not the ordinary lot of the mining industry, which must locate in the area of the deposit it is planning to mine and concentrate. In the case of copper this happens to be, for the most part, right in the heart of the semi-arid regions of the West.

Jan 7, 1960

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By Mayara Gallego Cucchiara

Neste trabalho, blendas de ABS (acrilonitrila-butadieno-estireno) e HIPS (poliestireno de alto impacto) provenientes de carcaças de equipamentos eletro eletrônicos (EEE) foram estudadas. O material foi moído em duas granulometrias diferentes (uma fina e outra grossa). Os corpos de prova para ensaios de tração e impacto de blendas ABS/HIPS na proporção 50/50 (% em massa) foram obtidas diretamente por injeção variando-se a velocidade de dosagem (50, 150 e 300 mm/s) e a granulometria do material moído (fina e grossa). Os corpos de prova obtidos foram caracterizados quanto às suas propriedades mecânicas (resistência à tração e resistência ao impacto). As diferenças obtidas nas propriedades mecânicas foram avaliadas através da análise de variância (Anova-fator duplo com repetição). Observou-se que a velocidade de dosagem e a granulometria do material não afetaram significativamente os valores de módulo de elasticidade aparente e deformação na ruptura das blendas obtidas. Já a granulometria mais fina resultou em blendas com uma maior resistência à tração e maior resistência ao impacto, não importando o valor da velocidade de dosagem utilizada durante o processo de injeção.

Aug 8, 2018

AS we contemplate the bestowal of the John Fritz medal year after year on men of wide-world dis-tinction in the various fields of engineering, men who in one way or another have given impulse and direction to the progress of mankind, the question becomes inter-esting as to what manner of man was John Fritz and what were the qualities that singled out his name to be so conspicuously associated with the world's great scientific and industrial achievements. If, as Lowell said, it is the duty of the nation to pro-duce great men, our country surely rose to her oppor-tunity when she guided and guarded the career of John Fritz. Starting life as a blacksmith with no advantages of education, without influential friends or the favor-ing accidents of fortune, he advanced steadily in use-fulness, power and respect of his fellowmen until by common consent he occupied the first place in the domain of the steel industry of this, country. The numerous honorary scientific memberships conferred upon him in this country and abroad attest the esteem in which he is held by his fellow engineers. Twenty years after his retirement from active business at the age of seventy, he lived to enjoy, as few men have been permitted to do, the fame and the friendships which he had so amply earned. His sterner qualities of industry, integrity and sterling character were re-lieved by unfailing human sympathy, humor and spon-taneous good-will toward his fellowmen. To all who

Jan 3, 1928

In general, modern mining companies all over the world have to face the same economic circumstances as any other part of the industry: considering the tough competition, production and haulage costs must be reduced permanently whereas productivity has to increase substantially in order to remain price-competitive. However, the imposed pressure also offers the chance for consideration of alternative mining concepts, the application of which can result in substantial cost savings and improvements in the quality of the mined material. As one of these alternative mining concepts, surface mining technology offers substantial improvements in productivity. It also influences aspects of haulage, such as safety and speed, in a positive way. The capability of selective mining ties in nicely with the production of small-sized crushed material, the granulometry of which allows the elimination of the primary crusher. Mine operators profit from reduced costs for the maintenance of their haulage vehicles due to reduced wear, a decreased likelihood of accidents and higher average transport speeds. Surface Miners can also be used to cut haul roads into virgin rocks and leave a clean and level surface behind, improving the quality of these created roads. Thus, it is even possible to use ordinary road trucks for transport in mines. The current paper outlines in detail the effects of the surface mining technology on mining and haulage aspects and reports on applications where substantial cost savings could be achieved due to the application of what is also referred to as æsimple mining processÆ.

Jan 1, 2003

By E. Beril

This may be a most unnecessary paper—from what does crude oil come and how was it formed. Many people, inside and outside of the petroleum industry, believe that we have actually enough oil, and that we can easily produce very important products from this extremely valuable raw material. The writer believes, however, that the answer to this question concerning the parent material and the formation of oil is of broader interest, because it may be that from the answer to these problems it would be possible to get answers to other important industrial questions. Therefore, a study in this line seems to be justified, and the writer will submit some of the results which he has collected during more than ten years with many very capable collaborators, to whom his thanks may be expressed on this occasion. Older Theories There is no doubt that plants were the parent material of coals, but opinion is divided as to the parent material of crude oil and asphalts. One group of specialists believed that they were formed from dead fish. The hydrocarbons of crude oil were formed by the splitting off of CO² from fatty acids formed by the saponification of the fat (glycerides) of fish. Enormous quantities of crude oil are present in many places on the earth, very often in several nonconnected horizons at the same location. This could hardly be explained by the so-called "catastrophe theory," which states that fish died through the entrance of salt water into fresh water, and vice versa. Furthermore, this theory cannot explain the presence of aromatic hydrocarbons, which can be found in nearly all oils, especially in the oil of the Netherlands Indies, which has more than 50 per cent of aromatics. Geological and chemical observations both lead to the belief that the temperature of formation of asphalt, crude oils and coals, perhaps with a few exceptions, did not exceed 200° C. Chlorophyll and haemin derivatives, which decompose above 200° C., have been found in all these materials by Treibs and others. Thermodynamic considerations show that the temperature necessary for the conversion

Jan 1, 1938

By Kazutaka Kunii

It is invariably certain that after punching for IC Leadframes, scrap metal were generated. These seraps were re-dissolved and in order to use as raw material for leadframes, it is necessary to remove the Ni plating. In this study a simple method was developed for the removal of Ni plating by surface oxidation of Ni plating. For this purpose a fundamental study was carried out on the oxidation behavior of Ni plating. Results showed that by controlling the oxidation condition, a considerably high rate of Ni could be removed.

Jan 1, 1996

By F. Rosenblum, P. Cancilla

The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automatic control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool. A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic¬based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the "wish list" of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight utilizing uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content.

Jan 1, 2002

By B. D. Cullity

This investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy—the thermoelectric efficiency—has been discussed by Telkesl in a recent review of the subject. She gives the thermoelectric efficiency as: W o Efficiency = -Wo ______________i____________ TR-TC+ O2TR-Tc) where W, = power output in external load (watts) Wi = rate of heat input to hot junction (watts) TE,T, = temperature of hot and cold junctions (oA) K1,Kz = thermal conductivity of the two thermocouple materials (watts/cm°C) p,,pz = electrical resistivity of the two thermocouple materials (ohm cm) 9 = thermoelectric power (volts0/C) For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of pfoperties. Bismuth-selenium Alloys work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson who gives the diagram reproduced in There are two intermediate phases in this system, BiSe and Bi²Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedra1 crystal

Jan 1, 1949