Search Documents

By S Marshall, A Fowler

The Augusta underground mine at Costerfield in Central Victoria has been in operation since mid 2006; however, AGD Operations Pty Ltd have explored and undertaken open pit operations in the area for over 20 years. The high-grade, narrow gold-antimony orebody is being mined using both mechanised and hand-held methods, to produce up to 70 000 tonnes per annum at ten grams per tonne gold and six per cent stibnite. AGD Operations Pty Ltd processes the ore on site using gravity and flotation to produce two products; a concentrate which is sold to Chinese smelters and a gravity concentrate which is refined off-site. The circuit achieves up to 30 per cent recovery of gold from gravity methods. There are many challenges in the underground mine, including an orebody with an average width of 300 mm, very poor rock mass conditions in the host rock and variable dips in the ore along strike, between 45¦ and 90¦. The upper levels of the mine have been developed ready for stoping; however, their depths range from 20 m to 70 m below surface in both oxide and transitional material. A major fault structure consisting of mud has been encountered underground and is associated with the orebody causing very poor ground conditions, water inflow and requiring additional reinforcement. The northern limit of the mine is defined by the proximity of historical workings in the South Costerfield mine, which is being continuously dewatered.

Jan 1, 2008

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

This report summarizes the work performed and results achieved in the period from 18 June 1971 through 18 October 1971 under Phase I (Task 1: Literature and Industry Search; Task 2: Conceptual Design and Evaluation; and Task 3: Concept Selection and Preliminary Design) in substantiation of the drill/impregnation machine concept recommended for detailed design in Phase II. Also included as Task 5 are recommendations for an experimental investigation to be conducted during Phase II. The report is submitted for approval and authorization to proceed to Phase II.

Jan 1, 1972

By C. A. Rowland

With the rapidly rising cost for electrical energy and the long range pre¬dictions for continued rising costs and even possible energy shortages, operation of rod, ball, autogenous and partial autogenous grinding circuits to efficiently utilize the power delivered to the mills will be demanded. This calls for a method to evaluate grinding circuit performance that is accurate, reliable and readily usable as an operating tool by supervisory, technical and operating personnel. Neither the Rittinger and Kick theories of comminution,(1) which preceded the Bond Theory by more than 50 years, had a mathematical means that could be used to predict and evaluate the performance of crushers and grinding mills used to comminute ores and rocks. This severly limited the practical use of these two theories, which were contradictory to each other. They have been superseded by the Bond Third Theory of Commnution.(1)

Jan 1, 1976

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Wayne D. Gould

The Cities Service Company's Pinto Valley mine and concentrator lie about 6 miles west of the town of Miami, Arizona at an elevation of approximately 4,000 feet above sea level. The concentrator started its first ballmill in July 74 and all six were available by November. Every effort was made to reduce capital costs, consequently, each unit process was studied critically to eliminate excess capital costs without loss of efficiency. Equipment selection was made on the basis of proven dependability and operating costs rather than on low bids. The result is a very workable plant with some important innovations. The concentrator is nominally 40,000 tons per day. The flowsheet is typical with 3 stage crushing, single stage closed circuit grinding, flotation, regrinding of rougher concentrate and cleaning of the rougher concentrate. The major equipment list is: 1 60 x 89 Traylor Primary Crusher 1 84" x 20' Stevens-Adamson Apron Feeder 3 7' x 16' Double Deck Tyler Screen 3 7' Nordberg Standard Crushers 6 8' x 20' Tyler Screens

Jan 1, 1975

By William Gleason

At 6,898 ft below surface, the historic No. 9 shaft at Resolution Copper near Superior, AZ is now the second deepest single lift mine shaft in the United States and connects to the deepest single lift mine shaft in the U.S., Resolution Copper’s No. 10 Shaft (6,989 feet). The shafts serve as ventilation and access for future underground development of what could one day become one of the most significant copper mines in the United States. It is from the base of No. 9 and No. 10 shafts that hundreds of employees of Resolution Copper, a joint venture of Rio Tinto and BHP, hope will soon be given the go ahead to begin driving lateral tunnels to reach a copper deposit that is estimated to contain 28 Mt or 40 billion pounds of copper. Copper was recently added to the U.S. Geological Survey’s (UGGS) critical minerals list, in large part because of increasing demand. A study by S&P Global Energy & Market Intelligence “Copper in the age of AI: Challenges of electrification” released on Jan. 8, 2025, “identifies a transformative trajectory for copper demand, projecting a surge from 28 Mt (31 million st) in 2025 to 42 Mt (46.3 million st) by 2040 – a 50 percent increase that underscores the metal's pivotal role in multiple technological and economic domains.” The surge in demand is driven in large part by the global energy transition, electrification of vehicles, growth of artificial intelligence and data centers, and most recently robotics. Meanwhile, geopolitical tensions have increased the focus on the need for the United States to secure more of its own mineral supply chain. S&P Global’s report is one of many warnings that while copper demand has accelerated rapidly, future supply is being held back. Resolution Copper stands out as one example of a known mineral deposit remaining locked in the United States’ complex and lengthy permitting slog.

Feb 1, 2026

Low-cost housing, like automobiles, should be appraised in the light not merely of first cost but of upkeep as well. Even more important than the number of miles the family car will go on a gallon of gasoline is the number of days the family home can be kept comfortable on a ton of fuel. A furnace tender who tossed every third shovelful of coal into the ashcan would lose his job promptly, but the effect is the same when homes continue year after year to pour out precious heat through uninsulated roofs and walls, Greater economy in household heating means even more to the national economy than to the individual, especially now that we are preparing for defense. Our fuel resources, although large, should be conserved. If less fuel is used for civilian needs, augmented requirements for defense can be met without unduly increasing the number of men needed at the coal mines and oil ells or adding new producing units that might complicate ultimate readjustment to peacetime conditions when the emergency is past and over-expansion of many industries brings new problems if unnecessary demands for transportation facilities are reduced, public carriers will be able to haul more munitions, and manpower needed for national defense will be released; and by protecting workers from health hazards in their homes additional man-hours of productive effort will be gained. Moreover, reducing the running expenses of houses by proper heat insulation helps home owners to maintain payments on property, and by minimizing foreclosures helps to stabilize the financial structure of the country. In short, here is a situation where the interests of the individual and the Nation are identical and the greatest good for the greatest number is obtained without sacrifice to anyone.

Jan 1, 1941

By Peter Middendorp, Gerald E. H. Verbeek

"This paper will describe a brief history of the method of characteristics as an accurate solution of the wave equation, and the author's experiences with the method of characteristics over a period of 30 years.As a result of the offshore pile driving activities associated with the development of the North Sea oil fields in the 1970's, two Dutch companies initiated extensive research efforts. Heerema started to research the dynamic behavior of soil during driving and HBG (Hollandsche Seton Groep) extended the method of characteristics with a straightforward theoretical solution for the shaft friction along a pile.The research institute TNO started the development of the wave equation program TNOWAVE in the late 1970's based on HBG's friction model extension for the method of characteristics. Today the program has a worldwide application in the field of pile testing. This paper will describe its development and application over time and its relation to today's applications for driveability studies for impact hammers (PDPWAVE) and vibratory hammers (VDPWAVE), signal matching for Dynamic Load Testing (DL TWAVE), Pile Integrity Testing signal matching (SITWAVE), and Statnamic simulation (STNWAVE).The paper will highlight that these developments have been the result of multi-disciplinary and multi-national efforts and encourage geotechnical engineers to seek further developments of the wave equation program in a similar manner. Finally, the paper will indicate some areas where such further developments are required."

Jan 1, 2005

By Gillyeard J. Leathley

The Cassiar Asbestos mine is situated on McDame Mountain in northern B.C. at a mean elevation of 6000 ft (1830 m), some 6 miles (9.6 km) from the townsite /mill complex. Asbestos ore production averages 1,200,000 tons at 9% R.M.G. (Recoverable Mine Grade) and waste production is 6,000,000 cu. yd annually. Waste is loaded by P&H 1900 AL 11-cu.-yd shovels and transported by 75-ton and 85-ton end-dump trucks to the waste dumps. The ore is loaded by a 992 Caterpillar 10-cu-yd front-end loader into 50-ton and 75-ton trucks, which transport it to the crushing plant located at the mine. The ore is transported by a 15,370-ft (4685-m) tramline to the mill complex.

Jan 1, 1978

By Michael W. Driller, Wen Yan (Grace) Chen, Steven J. Friesen

"Remediation for Perris Dam has been proposed in response to deficiencies identified in a seismic stability study prepared by the California Department of Water Resources (DWR) in 2005. Lenses of potentially liquefiable soil have been identified within the dam foundation which may lose strength during a seismic event. The remediation was designed primarily to limit deformation of the dam. Nineteen construction methods were compared and evaluated for the remediation. The final decision was to use cement deep soil mixing (CDSM) to strengthen the foundation and to construct a downstream berm to stabilize the dam. The entire CDSM treatment will cover over 4,000 linear feet of the downstream toe of the dam. Over 300,000 cubic yards of CDSM will be used to strengthen the foundation. The construction of the project started in Fall 2014 and is anticipated to take approximately 3 years. This paper describes the design aspects of using CDSM to treat the foundation, including laboratory testing, investigation of overstressing/cracking, extent of treatment, effect of CDSM on pore pressures under the dam, and the results of a full-scale CDSM test section.INTRODUCTIONPerris Dam is a zoned earthfill dam with a length of 2.2 miles, a maximum height of 128 feet, and a capacity of 131,450 acre-ft of water. The dam is located in Riverside County, California at the terminus of the East Branch of the State Water Project. The embankment was constructed between 1971 and 1973 over an alluvial deposit between the Bernasconi Hills to the South and Russell Mountains to the North. A rock outcrop divides the dam into left and right reaches when viewed from the reservoir looking downstream. The embankment soil was obtained from a borrow source at the North end of the reservoir. The dam has a sloping sandy clay core (Zone 1) with a 10-foot deep cutoff trench and a silty sand shell (Zone 2) with a downstream chimney and blanket drain (Zone 3 and Zone 4) as shown in Figure 1."

Jan 1, 2015

By S. Mohanta

In composite washeries optimization of operating parameters to achieve maximum clean coal yield at the desired clean coal ash level is a major problem. This problem is more acute in countries like India, which have predominant reserves of difficult-to-wash coals. The constrained operational parameters of washing for some equipments make it more severe. In addition to this, the dependence of separating performance of different equipments upon various variables aggravates the situation. Here an attempt is made to find a numerical solution to get maximum yield and minimize the difference between the actual and the theoretical yield. The solution is arrived through constrained non-linear optimization of a multivariable objective function that utilizes spreadsheet tools; the method accommodates any number of source coals or washing size fractions. By using a designed Ep value the predicted yield of composite clean coal has been calculated and the yield is optimized subject to constraints on both the ash and specific gravity. It is shown that operational constraints of different washeries in the composite plant that utilizes gravity separation methods can also be over-come. The technique offers the coal preparation engineer an effective and straightforward method for determining the optimum cut-points of separation for different coals or blended coals to obtain maximum product yield at a specified level of ash content.

Jan 1, 2014

"THE CONCEPT of energy as a commodity, while not entirely new, is not as widespread as the importance of the idea to this modern world would lead one to expect. The growth in the supply and use of energy over the past years has been tremendous, but our very closeness and familiarity have somewhat distorted the viewpoint, particularly of the younger generation. To many of us who remember the wonderful satisfaction of our first responsibility for directing two horsepower hitched to a farm cart or hay wagon, there still arises a feeling of some awe at the casual flick of the switch with which our sons and daughters summon to their convenience the service of some one hundred or more horsepower.Energy is the vital component of our existence and, no matter what contempt our day-to-day familiarity may •breed, it is wise to .pause from time to time and consider our national energy standing. Have we still capital in the bank? Are our expenditures wisely •conceived and well directed? Is provision being made for the years •ahead for the needs of our children and our children's children?"

Jan 1, 1953

By H. Sato, Y. Sato, T. Ooishi, K. Sakamoto

"Sumitomo Metal Mining Co., Ltd.(SMM)'s Niihama Nickel Refinery(NNR) produces high quality Nickel cathode, Cobaltcathode and other by-products using hydrometallurgical refining process called “MCLE”(Matte Chlorine Leach and Electro-Winning). In 2005,NNR started to use nickel and cobalt mixed sulfide (MS) produced by one of the SMM’s subsidiaries Coral Bay Nickel Corporation(CBNC)’s HPAL plant in Philippines, although its main and the only raw material until then was nickel matte. With start-up of the second HPAL plant at Taganito in 2013, NNR expanded its production capacity of nickel cathode from 41,000 to 65,000 tpa and finally achieved its target in 2015 by producing 65,980 tpa. SMM developed the technologies to improve poor reactivity of MS and installed new facilities to cope with increased Cobalt and Sulfur production at that time. This paper describes the technical approach to increase MS treatment with high efficiency.INTRODUCTIONThe Sumitomo Metal Mining Co., Ltd.(SMM)Niihama Nickel Refinery(NNR) produces Nickel cathode, Cobalt cathode and other by-products using Matte Chlorine Leach and Electro-Winning (MCLE) process technology. SMM uses nickel matte and nickel & cobalt mixed sulfide (MS) as raw materials for the MCLE process. Table 1 shows typical composition of these raw materials. Nickel matte had been only raw material until 2005, and with start-up of Coral Bay Nickel Corporation (CBNC) operation in the Republic of the Philippines, MS became major part of it. In 2009, when CBNC doubled its production capacity, NNR also expanded its plant capacity of electrolytic nickel from 36ktpa to 41ktpa, keeping an eye on the possibility of 65ktpa with oncoming SMM’s second HPAL in Philippines. Poor reactivity of MS was the prime concern at that time because our intention was to increase production with MS. Nickel extraction rate deteriorated with increasing usage ratio of MS in raw materials. To keep high nickel extraction rate under high ratio of MS, NNR developed a new leaching technology. Another concern arising from treatment of MS was Cobalt and Sulfur contents that are much more than those of nickel matte as shown in Table 1.NNR introduced new technology of solvent extraction process as to Co/Ni separation process in order to keep cost competitiveness instead of the conventional cobalt oxidation–neutralizing method. As to sulfur products, new sulfur productive facility was installed to improve the exposure to sulfur dust and the hot working conditions for workers. As a result of process development and installation of new facilities against the problem with MSusage,65 ktpa production was achieved in 2015."

Jan 1, 2017

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By C. M. McKinney

This report presents analyses of crude oil from most of the fields in the United States producing 2,500 barrels per day or more. The purpose of the report is threefold : 1) To present detailed analyses of crude-oil samples from as many al possible of the important fields in the United States. On January 1, 1947, there were 340 fields producing 2,500 barrels & day or more. Analyses for 283 of these fie1ds are presented. Fifty-seven fields have been omitted because the Bureau of Mines did not have analyses or the crude oils being produced. As one sample was not representative of the promotion from several of the fields, two analyses are given for each field of this kind. (2) To compile these analyses, many of which have not been published previously in a single report. Since the publication of Bulletin 291 in 1928, there has been no report showing analyses of crude petroleum from fields throughout the United states, but a number of separate reports according to area or state have been issued. Many of these are out of print. (3) To provide a means of ready comparison of the properties of crude oils from different areas of the United states.

Jan 1, 1948

By Omid Frough, Hossein Changani

Application of Tunnel Boring Machines (TBMs) is one of the main solutions to achieve a safe and high-performance method of construction in hard rock and soft ground tunneling. In order to adequately assess the progress and potential impacts of the tunneling operations with the TBM, it is required to record a series of data during the tunneling and process of the data to evaluate the TBM performance. Applying the right machine parameters during the excavation not only delivers an optimum penetration rate, but also prevents extra downtime due to over excavation or wear of cutting tools. In this paper, the effect of machine and operational parameters on TBM downtimes has been studied and supported with the real examples of TBM operation data.

Dec 1, 2022

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By J. R. Thoenen

This circular is the second of a series presenting methods employed in solving the technical problems encountered in the production of sand and gravel. The first paper3 discussed the methods use in prospecting and exploration. This one teals with the problems involved in bringing a raw prospect to the production stage and considers the various methods of development and the Factors affecting that development. Later publications are planned to present and discuss methods of recovery and treatment. The recovery of sand and ravel from natural deposits and their preparation for market involve a progressive sequence of operating steps or processes. Each step or process presents its own peculiar problems which require different angles of mental approach, methods, and tools, but all are more or less dependent on the step or process which precedes or follows.

Jan 1, 1933