Search Documents

By Duncan Chalmers, Rob Nowell, Miguel Araos

Australian underground mines produce in excess of 60 mtpa of coal. Most of these use the longwall method, and they require the use permitted explosives (which are called “permissible” in other countries) for challenges that appear during the day-to-day activities. To obtain the approval for these explosives, they should pass Testing Memorandum #2 (TM-2), which sets out the test required for each category of permitted explosive. These categories are P1, P3, and P5. With P5 being unrestricted use and P3 and P1 have conditional use in underground mines. The TM-2 test was originally set up for NG-based permitted products around 1900. With the closing of NG plants around the world, ammonium nitrate explosives were the natural replacement, and therefore these explosives need to pass the TM2. Australia does have a P1-emulsion based explosive available. For high-risk scenarios (like blasting coal), no P5 explosives are available. The lack of P5 explosives has been prolonged for more than 25 years, since the phasing out of nitroglycerine-based permitted explosive products around the world. The main problem has been that when emulsion based permitted products are tested in the deflagration cannon, the results obtained were not considered in the TM2 criteria and therefore the tests were invalid. A research work on permitted explosives began in 2005 funded by the Australian Coal Association Research Program (ACARP). The aim of the project was to address the lack of P5-type permitted explosive (and, potentially develop them further, i.e., develop safer explosives) and understand the behaviour of emulsion explosive and the results they presented in the tests. Both bureaucratic and technical barriers appeared along the way. On the bureaucracy side, the facility was shut down, reopened, and shut down again. In view of these difficulties, assistance was sought overseas. On the technical side, from the very start the results of the tests when using emulsion-based permitted explosives were not established in the criteria, ignitions occurred for trial samples that were expected to be P5-type, etc. The aim of this document is to present the painful journey in the Australian industry to have a P5-type emulsion-based permitted explosive, for use in UG coal. Also, the technical learning acquired about emulsion explosives and the ignition path of mixtures methane / air will be shown.

Jan 21, 2025

By Chas. F. Jackson

During the current business depression the Bureau of Mines has received many inquiries concerning placer mining, the prospects for men of small means to make wages by small-scale placer operations, the locations of placer deposits in the United States, methods of working placers on a small scale, and allied subjects. It has therefore seemed desirable to prepare a circular covering, in nontechnical language, the principal questions which have boon referred to the Bureau of Mines for answer. There are a number of bureau publications dealing with placer mining, most of which are now out of print, but which may be consulted in the larger libraries. Other articles on placer mining nave appeared from time to time in the technical press and several good textbooks have been written on the subject. A partial bibliography of this literature appears at the end of this paper. A recent pamphlet published by the Idaho Bureau of Mines and Geology to assist the prospector and inexperienced small operator has received wide and favorable attention and is recommended as a useful reference. In the present paper no attempt will be made to cover the subject of placer mining in a comprehensive manner, but discussion will be confined to elementary questions of particular interest to persons of limited experience.

Jan 1, 1932

By Fred Fuchs

"Most deep foundation work is either unseen by the general public or viewed as an inconvenience in their daily lives. Hurricane Katrina changed that perspective for everyone in New Orleans — and many other people in the U.S. and abroad. The public and the government of south Louisiana, and the U.S. Army Corps of Engineers (USACE), all needed to restore trust in the system that protects their property and, more importantly, their lives. While much has been written about the failures of government agencies, in this case incredible solutions were devised and implemented despite daunting schedules and arduous conditions. These solutions were achieved through collaboration, and through the efforts of USACE, where the goal was to fi nd the most expeditious and effective design/build solutions. This disaster thrust the pile driving industry into the national spotlight. Boh Bros. Construction Co., L.L.C., along with numerous local and national heavy construction companies, subcontractors, material suppliers and government agencies, take pride in the milestones reached after Hurricane Katrina.The majority of New Orleans’ population lives below sea level. Historically, the city has been protected by a fl ood control system consisting of earthen levees and I-walls (steel sheet pile topped by vertical concrete wall). Rainwater is pumped out of the city over this protection system and into canals that feed into Lake Pontchartrain. On August 29, 2005, when Hurricane Katrina made landfall just east of the city, the levee system experienced a major failure of several I-walls lining the outfall canals, causing flooding of 74% of the east bank of the city. The counterclockwise rotation of the wind pushed the lake water onto the south shore, raising the level of water more than 10 ft (3 m). A failure of 450 ft (137 m) of floodwall lining the east side of the 17th Street Canal caused extensive damage. This breach prevented the use of the pump stations that outfall into the 3-mile (4.8 km) long 17th Street Canal."

Jan 1, 2008

By C. West

Structured or embossed HDPE and LLDPE geomembranes have been available to mine owners and designers for over ten (10) years. As many owners and designers discover and demand the consistent high quality characteristics of this type of geomembrane due to the unique manufacturing process, the use of these materials in new mines, mine expansions and final closure designs has steadily increased. Structured liner materials are available for double lined and final cover systems and are revolutionizing the way ponds, pads and final closures are constructed. This paper will discuss the structured or embossed geomembrane concept and manufacturing process. Additionally, the paper will present comparative testing illustrating the major advantages of using this type of product in these types of applications. Both technical and economic advantages are illustrated. The cost savings include lower installation costs, less material used, and third party inspection times not to mention better performance. These new systems will be presented.

Jan 1, 2011

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

By D. E. Larson

The U. S. Bureau of Mines has developed a image analysis methodology to correlate the energy consumed during the grinding of an ore to the mineral liberation achieved. Energy consumption values are obtained using a laboratory-scale ball mill equipped with a torque sensor, and an automated image analyzer is used to determine the liberation present in ground products. By combining liberation information with energy consumption data an appraisal can be made of the energy required to liberate the mineral(s) of interest. Results of tests performed on a complex sulfide material determined the effects of grind duration on the liberation achieved and the energy efficiency.

Jan 1, 1995

By Joseph A. DeCarlo

The rapid growth of the organic chemical industry in the United States and abroad has focused attention on the future raw-material sources for this important industry. Chemical products are essential to modern civilization; and millions of tons of organic chemicals are used annually, ranging from basic raw materials to finished chemical products such as drugs, cosmetics, and soaps. Hundreds of chemical products are made directly or indirectly from coal, but in this report "coal chemicals" will be limited to crude tar, crud light oil, and ammonia recovered in the high-temperature carbonization of bituminous coal and the important principal products obtained by processing these materials. Specifically these include benzene} toluene, xylene, naphthalene, creosote oil, tar acid oil, pitch, and ammonium sulfate. Therefore the term "coal chemicals", wherever used in this report, includes only these products and does not include the secondary or intermediate products such as styrene, synthetic phenol, aniline, phthalic anhydride, or finished products made from these, such as synthetic rubber, plastics, and dyes. The United States leads the world in production and consumption of coal chemicals. In the past five years nearly one-fourth of the total output of coal-tar crudes in the world was produced in the United States. Consumption of some of the more important products derived from these crudes such as benzene, toluene, xylene, and naphthalene, however, ranged from about one-third to one-half of the world total because of imports and production of benzene, toluene, and xylene from petroleum. The synthetic organic chemical industry of the United States was established during World War I on chemical raw materials obtained by the high-temperature carbonization of bituminous coal but this source of supply currently furnishes less than 40 percent. More than 60 percent of the chemical raw materials used to produce organic and inorganic chemical is supplied by the petroleum industry and production of petrochemicals is rising rapidly.

Jan 1, 1960

By Earl R. White

In 1950 Kaiser Steel Corporation acquired control of the Utah Fuel Company, a pioneer Utah coal concern owning large reserves of high volatile coking coal near Sunnyside, Utah. The mines at Sunnyside have been producing high quality coking coal since the late 1890's. Kaiser Steel acquired the coal deposits at Sunnyside in order to supply the necessary coke for its steel plant at Fontana, California. The Sunnyside coal deposits are made up of two mineable beds, the upper and lower Sunnyside seams. Both seams outcrop along the southward facing escarpment of the Book Cliffs. The coal seams dip under the massive sandstones of the Book Cliffs to the northeast at 5 to 22 pct., with the steepest-part being near the outcrop. Mining at Sunnyside up to 1961 had been carried on with room and pillar methods. The deep cover and rotten roof conditions, along with the need of increased tonnage, required a change of mining technique. Numerous ideas were presented, discussed, and economically analyzed. Several people involved in these discussions, with the aid of W.W. II, had been introduced to the European methods of coal mining, namely the longwall technique. The European mines had long been plagued with near similar conditions as those at Sunnyside, particularly the deep cover problem. The longwall method seemed to be working very well under these conditions, and with the extensive studies given longwalling by the Kaiser Steel mining officials, it was decided to give longwalling a try.

Jan 1, 1976

By The Staff

THE property of McKenzie Red Lake Gold Mines, Limited, consists of eleven claims located on McKenzie island in Red lake. The mine is about 4,Y:l miles by water from the Howey townsite on the same lake, and about 95 miles north of Kenora, Ont. (see Figure 4). Mail and express are flown-in daily, winter and summer, from Sioux Lookout, Hudson, Kenora, and Winnipeg. All heavy supplies are freighted-in during the summer over a water route, using four marine railway portages, from Hudson, Ont., a distance of about 180 miles. During the winter, freighting over the same route is clone by tractor if necessary, but costs are three to four rimes the summer rate. Due to these conditions, large inventories of supplies must be kept on hand, varying from a spring minimum of $45,000 to a peak of $110,000 early in November. The average cost of all freight brought in from steel during 1937 was $0.01 per pound.

Jan 1, 1938

By Nidhi Kumari

This work is based on surface chemical properties of bacteria during adaptation to high grade copper minerals and the projected consequences in Bio-Flotation process. The utility of bio-processing in the beneficiation of copper ore through bio-flotation is demonstrated. An autotroph Acidithiobacillus Ferrooxidans bacterium is adapted to high grade mixed copper ore sample by repeated subcultures. The surface characteristics were studies by analyses at different pH and time intervals. From the studies, it was established that the mineral-adapted cells became more hydrophobic as compared to unadapted cells during bio-flotation. It was also noticed that there was no significant changes in the surface charge of bacteria before and after adaptation. Keywords: bio-flotation, copper, Acidithiobacillus ferrooxidans, hydrophobic

Sep 1, 2012

By Foster Bain

MOST of us householders in the East burn anthra-cite, so the problem that interests us most is the distribution and supply of the domestic sizes of anthracite. That, however, is only a small part of the coal problem and has its own peculiarities. Whether anthracite prices are high or low is largely a matter of relativity, depending on the size of the transaction, the available supply, and other things. As an isolated example which I hesitate to quote because it is not entirely representative, you may be interested to know that the Government fuel yard has been delivering to the Government buildings in the District of Columbia, white-ash stove coal at 16 c. a ton less during January, 1923, than during the same month of 1922. The reason is that the Government deals only with large companies who have been wise enough not to boost their prices and the small increase at the mine has been more than offset by the decrease in railroad rates. The total cost is $12.50 per ton, but I want to make it perfectly clear that it does not follow that this would be a just price for a retail dealer to charge the domestic consumer. For example, in the Government business there is no such thing as a bad debt, and certain other fixed or general charges are charged to other departments. The Bureau of Effi-ciency made an effort to determine what would be a. legitimate handling charge for a retail dealer, in Washington, and concluded that if the Government's cost of handling was $1.00, then $1.88 would be the corresponding fair charge to pay a retail dealer carrying the same volume of business, allowing for bad debts, complete depletion and depreciation of his equipment, and 10- per cent. profit. Assuming that this is the correct differential for Washington, it does not' follow that it would be equally just for Pittsburgh, New York, or elsewhere; nor does it by any means follow that it is a fair differential this year, because the dealer, after being unable to use his equipment in the summer months, now has to deliver an unusually large quantity of coal. I merely cite this instance to show that on the basis of primary cost of coal plus railway charges the retail price is not necessarily higher this-year than last.

Jan 4, 1923

By P. Hajiani

Rare earth elements (REEs) are critical materials in many leading-edge technology products. However, REE separation outside China has remained a challenge in addressing environmental concerns of current production. The author has worked on a technique employing the emphasised variability in the electrophoretic mobility (μi) of REE for the purpose of REE separation. In continuation of the results presented in IMPC 2016 [1], this contribution summarizes the progress achieved in 2016 and 2017. The major goal was to increase the REEs concentration by a factor of 1000 and to attenuate the consequent drawbacks, specifically joule heating effect. Amphiprotic hydroxylic solvent was selected to replace water, which has a major impact on the complexation mechanism and buffer requirement. Non-aqueous media result in a significant drop in the specific molar conductivity of the electrolyte, whilst μi reduces several times only. Moreover, a quasi-steady state electrophoretic separation in conjunction with temperature gradient focusing is adapted to improve scalability.

By H. Wotruba, L. von Ketelhodt, M. Kowalcyk, C. Kleine, M. Robben

Sensor-based sorting is a financially and technically viable technique that is operating with little or no water and relatively little power consumption. Sensor-based sorting has already proven its operational stability at two gold applications in South Africa. Sensor-based sorting cannot only turn waste dumps and diluted mining blocks into reserves. The implementation can also cause a decrease in specific operating costs of mill and mine when for example replacing selective mining by bulk mining methods with subsequent sorting. Successful installations, operational experience, test work data and flow sheet integration from mine-to-mill underline the impact and potential that sensor-based sorting can have on the gold mining and processing industry.

Jan 1, 2011

By Scott W. Hazen

COMPREHENSIVE summary is presented of results of several years of research at the Bureau of Mines Mining Research Center at Denver on adapting and applying techniques of statistical analysis in mine and mineral-deposit sampling and in computing grade and tonnage of ore for a mineral deposit. In addition to elementary statistical theory the material presented in the bulletin includes: (1) Certain special statistical techniques that have been found useful in mining applications; (2) problems, implications, and limitations that may be encountered in applying these techniques in mine sampling and evaluation; and (3) numerous examples to demonstrate application of the theory and techniques.

Jan 1, 1967

By R. J. R. Welwood, F. J. Grebenc

"Brunswick Mining and Smelting Corporation Ltd. (controlled by Noranda Mines Limited) operates two lead-zinccopper- silver mines approximately 20 miles inland from Bathurst, N.B. The principal No. 12 orebody is mined by underground methods; the second, the No. 6 orebody (6 miles away), is recovered by open-pit mining. No. 12 underground operations ar•e in two parallel massive sulphide orebodies about 400 ft apart, dipping at 75 to 80 degrees and plunging almost vertically. The initial mining phase involved longhole open stoping from the 1550 level to the crown pillar, with main levels at 150-ft intervals and sub-levels between at 75 ft. Stope dimensions average 120 ft long, 100 ft wide and 400 ft high, with alternate rib pillars as well as sill and crown pillars. Initially, ore was transferred through scram drifts below each stope by means of 125-hp electric slushers and 72-in. folding scrapers, being delivered to gravity ore-pass collection •systems feeding a primary jaw crusher below. Later, track and trackless drawpoints were utilized below most longhole open stopes and pillars. Rib pillars were recovered by longhole methods, with large blasts into a central slot and undercut, after adjacent stopes had been filled. Waste-rock stripping from No. 6 open pit has been supplied to No. 12 stopes as backfill, by means of gravityfill raises.In 1968, the decision was made to mine the remaining ore zones by mechanized cut-and-fill methods, utilizing Load-Haul-Dump equipment. Currently, approximately 60 per cent of No. 12 mine production comes from mechanized cut-and-fill mining. As before, backfill is supplied from No. 6 open pit stripping waste rock, which has been crushed to minus 6 in. The ultimate objective is to supply virtually all production requirements by mechanized cut-and-fill techniques. The No. 6 open pit, which commenced production in 1966, covers an area of 1,500 by 1,200 ft, equivalent to 41 acres approximately. Ramp roads are graded at 8.5 per cent. Each mining bench is 36 ft high and the ultimate pit will consist of 14 benches for a final pit depth of 504 ft. Present depth is 180 ft."

Jan 1, 1971

By Dan A. Mackie

Cyanide leaching operations have taken a beating from the press and the public at large for its seemingly haphazard approach to control of cyanide solutions and containment of tailings. Major spills in Colorado, Guyana, Spain, and more recently, Romania, have highlighted what had already been perceived to be a bad scene. Citizen initiatives and legislative actions are increasing. Whether these indictments are justified or not will not be debated in this paper. What this paper presents is that the technology to avoid these disasters and future ones has been around for more than ten years but has been ignored by the industry, despite demonstrated' cost effectiveness. It is time for miners to wakeup, and use emerging, instead of old, technologies.

Jan 1, 1998

By K. S. Radcliffe

Results are presented for the first phase of an experimental program to study the feasibility of using acoustic velocity for predicting the state of stress in a rock mass. Compressional wave velocities were determined axially in cylindrical samples during uniaxial compression for several rock types conditioned in dry and water-saturated environments. Results indicate that in rocks containing compressible voids or cracks, substantial velocity change occurs with the application of stress in the lower (below 100 MPa) stress regime. The effect norm- ally is nonlinear, however, and diminishes to asymptotic values when cracks or voids become closed or with saturation. Empirical prediction equations were derived for each rock type by linear and nonlinear regression analyses, and correlation coefficients were calculated to determine the equations that best fit the stress- velocity data. The operational range for predicting stress using compressional-wave velocity appears to be within the range of vertical stress expected in most shallow to intermediate depth mining operations (less than 1,000 m). Based on the experimental results to date and theoretical considerations, it appears that the technology can be advanced to predict in situ stress based on acoustic P-wave velocity determinations in most mining situations.

Jan 1, 1986

By V. A. Leão, M. L. M. Rodrigues, L. C. Sicupira, I. C. B. Rodrigues, T. C. Veloso

Brazilian sulphide ores can contain a significant content of chloride and fluoride, which are harmful to bacteria and thus bioleaching. This work summarizes a four-year research investigation on the effect of fluoride on both bacterial growth and sulphide bioleaching, supported by studies carried out with secondary copper ores. Firstly, the influence of fluoride on the kinetics of ferrous iron bio-oxidation with Sulfobacillus thermosulfidooxidans was addressed. Values as low as 10.0 mg/L F- fully inhibited bacterial growth, although fluoride toxicity could be overcome by the presence of aluminium, which reduced the concentration of hydrofluoric acid through the formation of aluminium-fluoride complexes. This required at least a 2:1 aluminium/fluoride molar ratio, which ensured bacterial growth rate values similar to that observed in the absence of fluoride ions. Subsequently, both batch and column bioleaching with mesofiles (30 ºC), moderate thermofile (50 ºC) or hyperthermophiles (67.5 ºC) of two secondary copper ore samples were analyzed with focus on the relevant effects of fluoride-containing minerals on the bioleaching of such sulphide ores.

Jan 1, 2014

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983