Search Documents

By R. J. McLaughlin

Acid mine drainage (AMD) can occur as a natural phenomenon through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhibit low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations -the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiquitous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treatment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper.

Jan 1, 1996

By M. Karmis

mining factors and representative ground movement parameters. Based on this analysis, the previously developed prediction methods were modified and tested for their applicability in the Appalachian coalfield. Finally, in order to facilitate the implementation of the prediction methods, as well as the data processing of the monitoring program, a number of computer software were developed and will be discussed in the paper. Surface deformations above underground mines and their prediction and control have been the topics of an extensive research effort by Virginia Polytechnic Institute and State University over the past few years. During the initial stages of this research, a number of case studies were collected from the literature, the mining industry and various government and state agencies and, based on the analysis of this information, appropriate prediction methods were proposed (Goodman, 1980; Webb, 1982; Hasenfus, 1984; Karmis et al., 1984). Although the prediction methods were based on sound concepts, it became evident that their accuracy and implementation were a reflection of the size and quality of the collected case studies. In this respect, the data bank was rather insufficient and posed certain questions regarding the development of subsidence information due to inappropriate length and spacing of monuments used in subsidence surveys, density and accuracy of such surveys, lack of monitoring horizontal movements, etc. In an effort to alleviate these problems, a comprehensive monitoring program was initiated in the coal mines of southwest Virginia, which included: - Two longwall and five room and pillar mines. - In total, seven longwall and sixteen room and pillar panels. - Monitoring lines in excess of 35,000 feet. - Vertical as well as horizontal measurements. A high accuracy digital computer tacheometer was used in all surveys and the type and spacing of all monuments were in accordance with well accepted guidelines. The data from this monitoring program completed the initially collected data bank and, thus, enabled a much needed statistical analysis between

Jan 1, 1987

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977

By R. T. Jones

The largest known platinum group metal (PGM) deposit in the world is the Bushveld Complex in South Africa, with the Great Dyke in Zimbabwe also being one of the biggest. It is therefore not surprising that the majority (just over 5 million troy ounces or 156 metric tons per annum) of the world's platinum is produced in Southern Africa. Primary smelting of ore concentrates is carried out in that region by five companies, namely Anglo Platinum, Impala Platinum, Lonmin Platinum, Northam Platinum, all of South Africa, and Makwiro Platinum in Zimbabwe. The only other primary smelter of platinum group metals is Stillwater Mining of Montana, USA, although very significant quantities of PGMs are produced as co-products by Norilsk Nickel of Russia. Smaller (but still significant) quantities of PGMs are produced by Falconbridge and Inco of Canada, also as co-products from nickel sulphide smelting. There are many similarities between PGM smelting and nickel sulphide smelting, and the range of technologies in use includes six-in-line rectangular electric furnaces, three-electrode circular AC furnaces, Peirce-Smith converters, and Anglo's ACP (based on Ausmelt technology). PGMs are also recovered from residue materials using DC arc furnace technology.

Jan 1, 2005

By E. Kalhan, C. Kincal

One of the biggest problems in open pit mining is slope stability. The avoidance of slope stability problems depends on a comprehensive assessment of environmental and operational factors such as geology, climate, and mining activities. In the light of these considerations, slope geometries should be determined in accordance with engineering principles. In this research, the slope stability of rock slopes in a mine opened in a gneiss geological unit has been studied. Production activities were ceased in 2019 due to the slope movements in the eastern part of the quarry. In order to safely continue the production, field works were primarily carried out. To assess slope stability, detailed discontinuity surveys were carried out on bench faces. Subsequently, kinematic and numerical analyses were employed to identify geometries that are expected to maintain stability under the prevailing geological structures and environmental constraints. Engineering geological studies such as scanline measurements in steps and investigation of potential failure mechanisms by kinematic analysis technique were carried out. Small module reactor and Q-slope rock mass classification systems were used to evaluate slope stability. Based on these classification systems potential unstable rock slopes were identified and thematic maps were created using geographic information systems. The most suitable slope geometries are suggested for these slopes. In addition, the improvement methods suggested by the rock mass classification systems were proposed for these slopes.

Sep 1, 2025

By Lanny Pasternak

"This article is directed at plant production, engineering and maintenance personnel. Seldom does any industrial operation take the time to study the costs involved in the generation of what is probably their most expensive plant utility energy source.IntroductionIn the typical industrial plant in Canada, a 200 hp, 900 cfm, air compressor costs about $60,000* per year to operate (Fig. 1). In 1989 when BC Hydro embarked on their industrial energy management program Airflow Energy Ltd. were asked to spearhead the “Efficiency Compressed Air” portion of that program with a mandate to perform onsite overview surveys and physical hands-on testing of some 300 selected industrial plants throughout British Columbia for compressor efficiencies and wasteful air leaks (Fig. 2). The program duration lasted until 1995, during which time a tremendous amount of data were amassed relating to equipment types, clients’ operating habits, end-use applications and operating costs.During the past six years, Airflow Energy also performed somewhat similar surveys but on a smaller scale in Alberta, Ontario, the United States and the Republic of China. It was no surprise to find some inherent equipment concerns related to efficiency as well as neglected energy wasteful air leaks, so British Columbia was not alone and the problems appear somewhat universal."

Jan 1, 1996

By E. Fregeau-Wu

The mineralogy and grain size distribution of phases in a steelmaking slag and experimental products from the heating of the slag under various conditions were determined to explore the possibility of recycling of the iron and manganese to the blast furnace. The steelmaking slags consisted of three major phases: dicalcium silicate, dicalcium ferrite, and Mg-Mn-wustite. Most of the phosphorus was contained in the dicalcium silicate and to lesser extent in the dicalcium ferrite. Due to the fine grain size of the dicalcium silicate, grinding and magnetic separation required pretreatment to increase the grain size and hence the liberation. Experiments on a steelmaking slag were conducted by heating the slag to 1633-1748°K( and slow-cooling in an inert atmosphere at various rates with or without the addition of fluorspar (CaF2) as a flux. Grain size distribution analyses of the starting material and the slow-cooled products were performed using the SEM-IPP area scan method and the QEM*SEM linear scan method. Comparable and reproducible results were obtained on the same sample using both methods. A size versus volume percent plot showed the increased grain growth most effectively. Examples of the grain size distributions obtained were used to show that a higher soaking temperature prior to slow-cooling, a slower cooling rate, and the addition of fluorspar to the slag promoted grain growth.

Jan 1, 1989

By R. C. Berry

The Environmental Impact Statement (EIS) has become a routine requirement for mining operations on federal lands. A similar document is being required in developing countries. Baseline studies are needed prior to writing an EIS and these studies involve surface water, groundwater, air quality, and wildlife/ native plant evaluations. The required baseline hydrology and geochemical studies are often the most expensive and lengthy evaluations. This paper summarizes the hydrology and geochemical baseline studies required for .An EIS and presents suggested methods to expedite these studies and to shorten the time and the cost to complete the studies and the EIS.

Jan 1, 1999

By G. F. Cross

INTRODUCTION THE electrical system associated with the mining development of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, may be conveniently divided into three main parts, namely, the Island Falls power plant, the transmission line, and the distribution systems at the mine and metallurgical plants. For a description of the Island Falls power plant and the transmission line, the reader is referred to the paper, to be presented at this meeting, by R. W. Davis and M.F. Huffaker (1). The transmission line and sectionalizing combinations are shown diagrammatically in Figure 1. The present paper deals with the distribution systems at the Flin Flon mine and metallurgical plants. THE FLIN FLON DISTRIBUTION SYSTEM In the high-tension sub-station at Flin Flon, each incoming 110 kv. line is provided with manually operated, gang-type disconnecting switches. Each line is connected to Canadian General Electric type F.H.K. 39-60B-F.2 T.P.S.T. 110 kv. 400 amp. oil circuit breakers, each provided with M.K.4 centrifugal motor-operated closing mechanism. Gang-type disconnecting switches are installed on each side of incoming line breakers, and a complete ring bus system is formed through station tie breaker, which is' further provided with gang-type disconnecting switches on either side. The?bus tie breaker is of Canadian Westinghouse design, type G.22B, 110 kv., 400-amp., solenoid-operated. All three breakers are provided with bushing-type current transformers, and the two line breakers are further equipped with bushing-type potential devices. Oxide film lightning arresters (121 kv.) are installed on each incoming line and are located outside the station. Each line is further provided with interlocked gang-operated ground disconnecting switches. All disconnecting switches are mechanically connected to auxiliary switches, which provide pilot service to indicating lamps in the remote-control room, located in a separate building.

Jan 1, 1935

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By C S. Walker

This paper analyzes the physical, operational and economic site conditions which were conducive to the design of a diesel-electric power plant wherein the over-all use of the thermal energy of the fuel exceeds 80 per cent. The heat energy supplied to the diesel engines is recovered in power generation, vapour phase cooling, waste heat boilers, air to exhaust gas heat exchangers and lubricating oil coolers. Electric boilers are also integrated into the plant design to enable the ratio of electric power output to heat recovery to be varied to suit the seasonal and daily variations. The criteria relative to thermal and electric power design requirements are discussed, and the design details of some parts of the plant which conform to these criteria are illustrated. Some data in regard to the actual operation of the plant over a short period are also included. Introduction THE Cantung mine (Canada Tungsten Mining Corporation) is located some 180 miles north-east of Watson Lake, Yukon Territory. It is situated on the upper reaches of the Flat river at an elevation of about 3,700 feet.

Jan 1, 1965

By D. D. Southworth

In 1987, the Bureau of Mines initiated a mineral assessment of the 5.7 million-acre Valdez Creek Mining District (VCMD). Following a literature search and interviews with persons knowledgeable about deposits within the district, limited on-site field visits were made to various deposits. Present within the district are the industrial minerals limestone, argillite, granite, basalt, perlite, zeolite, and sand and gravel. At least six limestone deposits of potentially economic size and grade are known to exist within the district. Adjacent to the Parks Highway and marginal to the district, a limestone deposit is currently being mined as a source of agricultural lime. A perlite occurrence near Yacko Creek was evaluated but proved not to be of industrial grade. The sand-and-gravel resources of the district are vast, but high silt content renders many of the glacial deposits unsuitable for use in construction applications.

Jan 1, 2011

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By W. J. S. Craigen, G. E. Wittur

"In the context of today's continuously changing world, there are many factors which must be considered when attempting to assess the ability of Canada's primary copper producers to remain competitive in the face of increasing competition in world markets. In this paper, we have attempted to document those factors that will have the greatest impact on the future viability of Canada's copper industry, and to suggest possible strategies to fully utilize whatever inherent advantages Canada may have to enhance its competitive position. Technological factors related to the efficiency of precious and by-product metals recovery, energy type and utilization efficiency, production and sale of sulphur by-products, and control of 502 emissions are given high priority in this evaluation of Canada's future needs to remain competitive. Particular emphasis is placed on assessing the relative viability of hydrometallurgical versus pyrometallurgical processes for copper; to address uniquely Canadian conditions and problems. Due consideration is also given to the economic incentives required to allow Canada's copper producers to compete under anticipated world market conditions and to facilitate the continued development of Canada's copper resources. IntroductionWhen we try to assess the viability or competitiveness of any industry the bottom line is still usually, ""Can we produce a pound of product cheaper than the competition?"" Canada's copper industry is certainly no exception. However, as with most resource-based industries dependent upon exports, there are many factors which have a significant effect on the cost components which make up the total cost of producing and selling a pound of copper. It is desirable therefore to have as clear a picture as possible of the cost components, the major factors affecting them, and how they compare with the competition, particularly the third-world copper producers.In this paper we have attempted to provide a brief outlook for world copper markets and a brief overview of Canada's competitive position. We have also attempted to document those factors which will have the greatest impact on future production costs, and have suggested possible initiatives to utilize inherent Canadian advantages to enhance our competitive position. Special emphasis has been placed on technological initiatives designed to make full use of these ""advantages"", to develop superior beneficiation and extraction! refining technologies. Major factors considered in the present study are:"

Jan 1, 1986

By D Michaelsen, S Miller

The Grasberg Mine is a copper and gold open pit mine operated by PT Freeport Indonesia (PTFI) and located in the high equatorial mountains of the Indonesian province of Papua. The climate is alpine/subalpine with little seasonal variation in temperature or rainfall. The daily average temperature ranges from about 2¦C to 14¦C and the annual rainfall in the vicinity of the mine and overburden stockpiles is about 4000 mm to 5000 mm. Mining of the Grasberg open pit will continue until 2014 at which time approximately 2750 Mt of overburden will have been produced. Current overburden production rates are 200 Mt per annum. The current mill rate is 230 000 t/day from the Grasberg pit (190 000 t/day) and the underground operations (40 000 t/day). The acid rock drainage (ARD) issues associated with overburden from the Grasberg operations were identified early in the mining operation. Almost all overburden placed to date has been Potentially Acid Forming (PAF). Laboratory testing has identified four main overburden types: limestone and non-acid forming (Green waste), PAF low capacity (Blue waste) and PAF high capacity (Red waste), and Heavy Sulfide Zone (HSZ), which contains greater than 20 per cent pyrite. Waste type block modelling indicates that at least 30 per cent of the overburden production from 2003 to the end of Grasberg pit operations will be limestone. Strategies are being developed to maximise the beneficial use of limestone through strategic blending and placement for ARD mitigation and control.

Jan 1, 2003

By S. H. Seyedein

A mathematical model was developed to study fluid flow and solidification in a single-roll casting system. Fluid flow coupled with energy equations were solved numerically using a finite volume method. A body-fitted coordinate transformation technique was adopted to handle the irregularly shaped domain. In order to couple the continuity and momentum equations, a SIMPLEC algorithm was used. A fixed-grid enthalpy method was considered to model the solidification in the system. The turbulence effect on flow field was modeled using a low-Re k-e model The model developed in this work was further run under various conditions to optimize the operating parameters of the process.

Jan 1, 2004

By Cassandre Nowicki, Louis Gosselin, Carl Duchesne

"Quebec's primary aluminium production industry consumes roughly 39 TWh of electricity per year and is accountable for roughly 7 million tons of CO2 equivalent. By tapping only a small portion of waste heat and integrating it inside the production facility itself, we can significantly reduce GHG emissions and energy consumption. Although the amount of thermal waste can be adequately estimated by applying an energy balance to production processes, this provides very little information on the quality of waste heat and its potential for integration. A measure of exergy is required. Waste heat streams characterized by high exergy content may generally offer valuable incentives for recovery and integration. More generally, exergy values limit integration possibilities. An exergy analysis is provided for the aluminium electrolytic reduction process. This is meant to guide future heat recovery initiatives and energy efficiency measures.IntroductionCanada is one of the world leaders in primary aluminium production and 92% of its aluminium production capacities are located in the province of Quebec. In 2007, production capacity reached 2,786,000 tons in Quebec alone. Since it is estimated that 2.5 equivalent tons ofCO2 are released for each ton of aluminium produced in Canada, Quebec's aluminium production industry is accountable for roughly 7 million tons of CO2 yearly [1, 2]. Furthermore, with an average electricity consumption of 14 MWh per ton, primary aluminium accounts for 39 TWh of electricity per year in Quebec and this energy consumption represents 350 thousand tons ofCO2 equivalent [3, 4]. Natural gas consumption associated with primary aluminium production accounts for less than 1 TWh, but it represents an additional 350 thousand tons of CO2 equivalent [ 4].This work is meant to provide a tool to guide future efforts towards heat recovery and energy efficiency in the primary aluminium industry. Waste heat recovery and thermal integration can cut down both energy consumption costs and GHG emissions. In a primary aluminium production facility, waste heat represents roughly half of the energy input into the Hall-Heroult process. Tapping only a small portion of this energy could reduce natural gas and electricity consumption significantly. In order to evaluate how much of this energy is actually usable, we propose to apply an exergy analysis to individual transformation processes in an aluminium production facility, such that a potential to do work can be assigned to every waste heat flux. The approach will be described in the next section."

Jan 1, 2012

The Australian Mineral Industry has to compete on world markets, so its mineral research has to be aware of overseas developments, it must be of world class, and it must utilise as many ideas as possible in order to solve those problems that uniquely affect Australian minerals processing. North American mineral and resource research may be taken as a guide to world government, industrial, contract, and entrepreneurial research trends and ideas. A number of interesting findings are noted that may guide Australian developments and strategies for the future, in minerals research and exploitation.

Jan 1, 1986

By Jim F. Lemons

The Bureau of Mines Minerals Availability System collected and analyzed data for 34 nonlaterite and 9 nickeliferous laterite domestic chromite deposits in order to assess their viability as sources of chromium under present technologic and economic conditions. These 43 deposits, none currently in production, contain approximately 6.3 and 22.3 million metric tons of Cr203 at the demonstrated and identified resource levels, respectively. Approximately 4.6 and 15.6 million metric tons of Cr203 are recoverable at the demonstrated and identified levels, respectively, for the 34 nonlaterite deposits. None of these resources are economically recoverable at January 1981 market prices. Production of metallurgical-grade chromite (market price $128 to $144) would require a minimum chromite market price of $237 per metric ton. Chemical-grade chromite production (market price $74 to $85) would require a chromite market price in excess of $188 per metric ton. From the 34 nonlaterite deposits, roughly 5.4 and 17.6 million metric tons of ferrochrome could be produced at the demonstrated and identified resource levels, respectively; however, a minimum market price of $770 per metric ton of ferrochrome would be required to stimulate production. The nine nickeliferous laterite deposits were not evaluated through production stages because of uncertainties in process technology and cost.

Jan 1, 1982