Search Documents

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"One of the most pervasive diseases in the mining industry is noise-induced hearing loss. The exposure of miners to noise levels above the permissible exposure level results in hearing loss in approximately 80% of coal miners by retirement age. In this context, the U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for longwall mining systems, which are used to extract half of the national underground coal production.From field measurements, previous research determined that the dominant sound-radiating components at the shearer of a longwall system are the two cutting drums used to remove coal. Due to the dimensions and complexity of longwall mining systems, the NIOSH project developed a validated finite element model of the cutting drum to use in predicting the sound radiated by the drum due to the excitation forces experienced in underground operations. This same model will be used to develop engineering noise controls for the drum. The excitation forces arise from the interaction of the cutting bits and the coal and are transmitted to the cutting drum through the bit holders. Due to the adverse conditions at the face, and a lack of instrumentation approved for underground use, the operational coal cutting forces have not been assessed before. To this end, NIOSH, in collaboration with Michigan Technological University, developed a self-contained, intrinsically safe instrumented bit to measure these forces.This paper describes the development of the instrumented bit and the measuring of operational coal cutting forces at three working coal mines. The measurements revealed that the forces have a flat spectrum, representative of the impact nature of these forces, up to around 100 Hz. Above this cutoff frequency, the force magnitude decreases at a rate proportional to the inverse of frequency squared."

Jan 1, 2014

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The Dynamics Effects Laboratory at the University of Maryland conducted a series of very small scale tests to measure the impulse delivered to a plate by the detonation of an explosive charge which was buried in saturated sand. These tests were conducted to support a full scale tests series being supported by the Navy (NSWC Indian Head Division) to learn more about loads applied to structures by explosive detonation. For each of the tests being predicted, a series of three tests were conducted at Maryland, one with a 0.203 gm charge, one with a .609 gm charge, and one with a 3.3 gm charge. A high speed digital camera (500 frames per second) was used to record the displacement of the plate as a function of time. From this the initial velocity of the plate was determined and then the impulse delivered to the plate by the explosive. A best fit line through the data was determined for the three model tests conducted and this equation was used to extrapolate the predicted impulse for the full scale tests.

Jan 1, 2005

By K Williams, G M. Evans, S M. Iveson, K P. Galvin, C E. Loo

The Australian Research Council (ARC) has recently established an Industrial Transformation Research Hub in the area of iron ore, focused on iron ore characterisation, beneficiation, materials handling and end-use functionality. The research hubs are part of a new initiative aimed at building stronger relationships between industry and universities, while addressing issues of national significance. The ARC Research Hub for Advanced Technologies for Australian Iron Ore will focus its attention on developing innovative approaches for creating enhanced value across the full value chain through the characterisation of different ore types, beneficiation and materials handling and transport. This hub brings together five industrial organisations and a research team formed from well-established research groups based at the Newcastle Institute for Energy and Resources. These groups have a record of working closely with industry to create opportunities. Examples include new beneficiation technologies such as the Reflux Classifier for achieving gravity separation, the expertise of TUNRA Bulk Solids in materials handling and the Iron Making Centre at Newcastle, which is a capability maintained by BHP Billiton following the closure of its Technology Centre in 2009. The purpose of this paper is to provide an outline of the research hub and its objectives, some background on the research groups that now form the hub and an insight into the strategy adopted for developing and implementing new technologies. The paper also describes a range of novel technologies that have the potential to be developed and applied to iron ore beneficiation.CITATION:Galvin, K P, Roberts, A, Loo, C E, Evans, G M, Williams, K and Iveson, S M, 2015. Australian Research Council research hub for advanced technologies for Australian iron ore – an introduction, in Proceedings Iron Ore 2015, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By Scott Rosenthal, David Gilkey, Michael McGivern, Lorri Birkenbuel, Daniel Autenrieth, Ty Murphy, Hadi Aldossari

A safety climate case study was carried out at a surface metal mine where investigators administered the Liberty Mutual Short Scale Safety Climate Survey to 365–368 miners to measure safety climate in consecutive years. Following the baseline safety climate survey in 2019, Foundations for Safety Leadership (FSL) training was conducted with 81 middle to upper management employees at the mine site. Investigators found statistically significant differences in the pre vs. posttraining FSL assessment scores of the middle to upper management employees who attended the training. The follow-up safety climate evaluation was compared to baseline scores and revealed no significant improvement. The overall baseline company safety climate score of 76.38 increased minimally to 76.50 (p-value = 0.616). Investigators also evaluated differences in safety climate between the company’s three major divisions (operations, maintenance, and administration). Both years administration had the highest mean score and operations had the lowest mean score. The authors attributed the statistically significant differences found among the three major divisions to various dissimilarities in their work environments.

Aug 13, 2021

By Al Gagnon

Since start-up in 1972, many circuit problems have been encountered, most of which were related to the abundance of fines (-28 mesh), which the circuit had not been designed to treat. The major problems associated with the original circuit included excessive loss of magnetite, reduced throughput during periods of a high proportion of fine coal in the plant feed and low yield in the fine coal circuit. This paper outlines the coal processing circuit at Fording Coal Limited as it exists today, with emphasis on the changes to the original fine coal treatment circuit.

Jan 1, 1978

By David Miller

Longwall gateroad support can be supplied by a variety of methods. The system of support also needs to be flexible as conditions change. This is especially true in the complex geological conditions of the west Kentucky # 13 seam. Methods of gateroad support used in this seam will be presented along with the successes and failures of the systems as conditions changed Lodestar Energy&apos;s gateroad support progression through the seven longwall panels retreated to date will provide an insight into planning for future panels

Jan 1, 1998

By Paul Worsey, Larry Frost, Braden Lusk, Seok Bin Lim

For certification of blast resistant windows, current tests consist of arena tests or large air gun tests. Arena tests involve the detonation of more than 1000 pounds of explosives with windows placed in the range of hundreds of feet. The result of an arena test is a loading on a window consistent with an expected industrial or terrorist blast. Due to the nature of this type of test, only a limited number of facilities are available and operational costs can be extremely high. Air gun tests involve the use of compressed air and a failing diaphragm fired through a large tube. Although this test is more cost effective and easier to administer with lower environmental impacts, it is not an explosive loading and does not create a negative phase on the tail of the pressure pulse. Simply using a small charge in close proximity to the window is not a viable option either. The pressure peak can be reached using this method, but the duration of the pressure pulse is such that the positive phase impulse is on the order of ten times less than that for an arena test.

Jan 1, 2006

By P. C. Holloway, M. J. Collins, K. R. Buban

Historically, there has been little incentive to process copper-arsenic concentrates by leaching, rather than via established smelting operations. However, with ever tightening environmental emission standards and more arseniferous concentrates being produced, increasingly sophisticated and upgraded off- gas handling facilities are required in smelting operations, generating greater quantities of challenging metallurgical dust. In this context, oxidative pressure leaching offers distinct advantages. The current state of pressure leach technology delivers high extractions from copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. However, as was shown in an earlier study, copper extractions and environmental leach residue stability are impacted negatively by arsenic levels above 2.5 to 3.0 wt%. In further studies on pressure leaching of copper concentrates, Sherritt has developed process conditions that allow even highly arseniferous (> 7 wt% As) feed materials to be converted into environmentally stable residues, with excellent copper extractions. At the same time, pressure leach residues can be generated that are amenable to silver recovery via direct cyanidation, without pre-treatment by lime boiling or hot curing. The results of pilot plant test work are discussed. INTRODUCTION As the production of copper has expanded over the years, resource exploitation has extended beyond relatively clean, high grade and easily accessible ores, and copper sulphide concentrates increasingly come with higher levels of contaminants, such as As, Hg, Sb and Bi, and lower copper and sulphide sulphur concentrations. However, as concerns on the impact of the emission of such contaminants into the natural environment have mounted, import/export restrictions have made the trading of copper concentrate more difficult, and, in particular, the export of concentrates with greater than 0.5 wt% As; under ever tightening environmental emission standards, these lower quality concentrates can be a significant strain on the off-gas handling facilities in smelting operations. The processing of arsenic bearing copper concentrates is, therefore, an increasing challenge as copper producers seek to exploit more complex mineralization and to extend the life of their operations. In this environment, processing arsenical copper concentrates with high temperature pressure leaching (>200°C) must be considered as an alternative to pyrometallurgical processing. Leaching kinetics for copper minerals at these temperatures are rapid and acid is generated for potential use in heap leach operations. Pressure leaching of copper concentrates eliminates gaseous emissions of arsenic and sulphur, while generating environmentally stable residues, as measured by the Toxicity Characteristic Leach Procedure (TCLP) (Kalanchey et al., 2007). Both medium and high temperature pressure leaching of copper concentrates have also proven themselves technically on an industrial scale (Marsden et al., 2004) with high copper recoveries.

Jan 1, 2019

By G Deans, M Longbottom

OZ Minerals’ Carrapateena mine is one of Australia’s newest ‘greenfield’ mining deposits. It will be a 4.25 Mtpa sub level cave underground operation, with an estimated mine life of 20 years. The integration of stakeholder values to inform project development influenced the social and environmental outcomes. A Native Title Mining agreement was developed in 12 months. Project primary approval was obtained 12 months from submission, with achievable licence conditions and one public comment. The project moved from a Pre-feasibility Study in 2016 to construction in 2018. Following recent international dam failures, the Tailings Storage Facility (TSF) was a focus for Government approvals and stakeholder engagement. Significant effort was made into understanding the science around potential effects, impacts and risks. A leading practice Impact Assessment Framework that identified Sources, Pathways and Receptors was applied. A process of failure mode identification and layers of protection analysis was undertaken for robust design controls at each stage, while simultaneously transitioning between downstream and upstream discharge arrangements. Participatory selection of the TSF site and design layout was critical in managing project costs and environmental constraints, and in incorporating cultural heritage constraints and technical risks.

Jul 1, 2021

By J. Drelich

The adsorption of oleate at the surface of titanium dioxide from aqueous solutions was examined by Fourier transform infrared (FT -IR.) spectroscopy using a germanium internal reflection element coated with a thin film of TiO2. This thin film, with a thickness of 100-200 A, was deposited on the surface of a germanium single crystal by RFIDC magnetron reactive sputtering. It was found that significant adsorption of oleate from a 0.02-0.03 mM aqueous solution on the surface of TiO2 thin film occurs at neutral pH, from about pH=5.5 to pH=7.7. Adsorption of oleate at the surface of the amorphous TiO2 thin film appeared to be reversible, involving soap-acid dimers.

Jan 1, 1997

By Myron W. Mellor

Our efforts at McNally, to find a better way to mechanically separate particles from liquid in a slurry have led to the development of two new centrifuges. The first unit utilizes a slotted opening screen as the filter media and retains all plus 200 Mesh and most of the 200 by 300 Mesh particles. The second unit is a solid bowl centrifuge with a novel method of removing the solids and delivers an effluent containing as little as 300 PPM solids in suspension. The first unit was designed to separate particles in the range of about 1 MM x 0 or smaller top size from the liquid slurry and produce solids having low surface moisture content, and a liquid concentrate containing a low percentage of solids. A prototype of this unit has been in the field undergoing tests for over two years. A few of these test results are shown in Tables I & 11. Testing has been mostly limited to the field of coal, how- ever this does not mean that the machine would accept only coal slurries. The machine has produced a dewatered product having as low as 5.5% surface moisture, and an effluent containing as low as 1.4% solids and handled slurries containing from 15 to 50% solids by weight.

Jan 1, 1975

By J C. Koppe, L Vieira

One common problem for blasting in iron ore mines with significant weathering is the occurrence of large blocks of hard rock mixed with softer material. This situation causes a problem for blasting design and sometimes produces large boulders of rock that require a secondary blasting, as well as excavation difficulties. To minimise this situation, geophysical techniques were used to identify the hardest material amid the weathered material. To study the problem, seismic, ground penetrating radar (GPR), electrical resistivity and induced polarisation (IP) methods were used in an intensely weathered Brazilian iron ore deposit. The methods of GPR combined with IP, resistivity and seismic showed to be effective in modelling the contrast among hard, friable materials and soil. The results were used to improve the geological model and create more favourable conditions for the subsequent blast design. The blast design based on geophysical/geological models resulted in significant improvement in the fragmentation of the iron ore. This was achieved by the adoption of a specific drilling pattern for a given geological situation. With the new specialised blasting design the formation of boulders was eliminated.CITATION:Vieira, L and Koppe, J C, 2015. Geophysical techniques applied to blasting design, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 289–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Frank T. Sisco

DURING the past year the iron and steel industry of the world as a whole operated on a satisfactory basis. No discoveries nor new processes of outstanding importance were announced either here or abroad, although rumors of such were persistent. In general, the efforts of operating and research men in the iron and steel industry seemed to be confined to improving quality and reducing cost, not a new aim, for the same efforts have been noted in nearly all of the annual reviews of the industry for at least fifty years. Most published papers on blast furnace or steel-making practice were of minor importance, at least when judged by the criterion of radical change in process or product. If the number of reports in the technical journals, or articles in the trade press, is used as a basis for comparison, continuous-mill sheet is still the most important single product of the industry; papers were published detailing the results of the investigation of various phases of the

Jan 1, 1938

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By Soumitro Nagpal

Bacterial oxidation of a pyrite-arsenopyrite-gold ore concentrate was carried out in .14-liter continuous-flow stirred-tank reactors (CSTR). Oxygen and carbondioxide consumption rates mineral dissolution rates, and bacterial concentrations were measured at various steady-state residence times and with 6, 11, and 16 wt.% solids in the feed slurry. A sharp optimum in biooxidation rate .was found at a residence time of approximately 40 hours for operation at each of the three pulp-densities. Biooxidation rates increased consistently. with increasing pulp density. Cell washout accompanied by negligible biooxidation rates was found to occur at a residence time of approximately 20 hours. Mineral&apos; oxidation was found to be strongly dependent on bacterial activity. Arsenopyrite was found to be preferentially oxidized? at the higher Pulp densities.

Jan 1, 1991

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991

By Xinyang Xu, Chen Zhang, Lixia Li, Zhitao Yuan

"Density functional theory was employed to clarify the mechanisms of the activation of a quartz surface and its collection by the flotation method at the molecular level. The calculation results indicated that hydrogen bonds on the quartz surface (1 0 1) existed in pairs while in contact with water. The simulation was carried out to investigate the different effects of Ca2+ and Ca(OH)+ on a quartz surface with hydrogen bonds, and the results suggested that Ca(OH)+ most likely adsorbed onto and activated the quartz surface. Mulliken population analysis of the external oxygen atom of the quartz surface, calcium atom of Ca(OH)+, and the oxygen atom of oleate showed that there were electron transfer and the formation of a chemical bond between Ca1-O1 and Ca1-O3, which were indicative of strong interactions between the three atoms. In addition, the –OH of the Ca(OH)+ contributed to the activation, which suggested that the Ca(OH)+ group acted as a bridge between the surfaces of oleate and quartz.INTRODUCTIONFlotation is an effective separation method in mineral processing that takes advantage of the physicochemical differences between minerals and gangue, and the properties of the mineral surfaces play a key role in this process (Liu et al. 2016, Qin et al. 2017). In the reverse flotation process of iron ore, gangues are captured by cationic or anionic collectors and floated with air-bubbles as tailings, and the pre-depressed iron oxide minerals are left at the bottom as concentrates (Lima et al. 2013, Yianatos et al. 2015, Zhu et al. 2015). Quartz (SiO2) is one of the major gangues of hematite ores and cannot be easily removed. It is a naturally hydrophilic mineral, in which silicon is the cation in its crystal structure and has very limited solubility. Therefore, quartz must be activated, usually by metal ions, for its effective rejection as a float-product by reverse flotation (AIME. et al. 1976)."

Jan 1, 2018

As a bubble travels through the pulp region of a flotation cell, it will collect the most hydrophobic particles of an intermediate particle size range, this being the primary source of true flotation selectivity. Despite its role on bubble-particle attachment, however, particle hydrophobicity is still missing a mathematical definition that can be used for plant simulation. In this paper, particle hydrophobicity is defined in terms of the induction time necessary for attachment and then linked to the mass of collector adsorbed per particle. This allows particle hydrophobicity to be written as a function of density of collector adsorption as well as particle size and mineralogy. The model is calibrated from the experimental measurement of the flotation rate constant. Liberation data from an industrial flotation rougher is used for model validation. It is demonstrated that the model can describe a broad experimental dataset by means of a minimal number of parameters. Main industrial application is in simulating the effect of the chemical environment upon plant metallurgical performance.

Jan 1, 2006