Search Documents

By B J. Monaghan, R J. Longbottom, S Prabowo, D Del Puerto, B Maisuria, C W. Bumby

The use of hydrogen as a reducing agent can substantially reduce carbon dioxide (CO2) emissions from the ironmaking process. Iron ore fines can be reduced in a fluidised bed (FB) using hydrogen (H2) at high temperatures (>800°C), although several studies have reported the sticking of particles which causes the bed to defluidise, effectively shutting down the process. Here, we report results from the reduction of New Zealand (NZ) titanomagnetite (TTM) ironsands in a small-scale laboratory FB (100 g) at temperatures between 800–1000°C using H2 flow rates up to 5 standard L/min. No sticking phenomena are observed under any of these conditions, which is attributed to the formation of a stable titanium-bearing oxide layer on each particle’s exterior, preventing iron-iron contact at the particle surfaces. Pre-oxidised NZ TTM ironsands have also been studied and shown not to stick. Interestingly, at lower reaction temperatures the reduction kinetics for pre-oxidised ironsands is faster than for as-received ironsands. This increased kinetic rate can be attributed to the preoxidation stage inducing micro-fractures that create a void for the hydrogen to diffuse into the inner regions of the particle. In addition, oxidation of TTM appears to segregate the particle into two distinct phases, a high Aluminium-Magnesium (Al-Mg) phase and a high Titanium (Ti) phase. The findings are important as increasing the operating temperature of the FB reactor results in a faster reaction rate and higher gas utilisation, making the process more economically attractive. Furthermore, oxidation of NZ TTM ironsands results in a faster reduction rate at lower temperatures (800°C– 900°C) opening the opportunity to reduce the reaction temperature which might be beneficial in a final commercial-scale process.

Sep 18, 2023

By Forrest K. Pence

BENTONITE deposits are known to occur in Texas within the Jackson group of formations. This group represents the uppermost Eocene age sediments found in the coastal plain area of Texas. It outcrops across this area of the state in a narrow band of some 4 to 20 miles width. The outcrop pattern roughly parallels the present Gulf of Mexico shore line and is some 100 miles inland from the Texas shore, Fig 1. The principal bentonite deposits are found in the areas where this outcrop pattern cuts across the south-central Texas counties of Karnes, Gonzales, and Fayette. In these deposits, the better quality bentonite is found in the lower or bottom layers of the volcanic ash deposits in which they occur. Some of these better quality bentonites develop very light colors upon firing and therefore justify their being classified as "white firing." The deposits in Karnes and Gonzales Counties apparently occur in commercial quantity, whereas the white firing strata so far uncovered in Fayette County have been too thin to be classified as yet as "commercial." A study of the ceramic properties of the weathered ash in Gonzales and Karnes Counties was reported in 1941.1

Jan 1, 1949

By D. A. Fenton

The reliability of large diameter, high horsepower ball mill is paramount when large production and minimum downtime is required. The 17 ft. x 56 ft. double compartment ball mill at St. Lawrence Cement Company has the first gearless drive built in North America and has the world's largest hydrodynamic bearings currently built and running. The machine has seen three years operation and has met its specifications. The mill was designed by Aerofall Mills Limited and the gearless drive built and designed by the Canadian General Electric Company. This paper discusses the operation of the first North American installation of a gearless drive ball mill from the mechanical, electrical and process aspects.

Jan 1, 1977

By Theodore James Kurela

Analysis of adverse technical issues has traditionally relied on a snapshot of the state of the operation complemented with both the melt shop’s archived data and eyewitness accounts of adverse events. The GrafTech ArchiTech System is helping EAF shops solve problems faster by combining continuous analysis of information with statistically based alerts of process deviations. After one year of system implementation, a number of cases have been detected and communicated to melt shops worldwide. The objective of this paper is to examine a few of these cases; the early detection, statistical analysis, deviation reporting and the resulting countermeasures implemented.

Aug 17, 2017

By M Thompson, N Vines, Z Hearne, S Lam, G A. Gomes-Sebastiaõ, D van der Spuy

Construction and commissioning of the Nova Copper-Nickel project of Independence Group was completed in late 2016. The plant is in the Fraser Range of Western Australia, about 120km east of Norseman and produces separate Copper and Nickel concentrates. Since the early feasibility phases of the project, the importance of automation and control was recognised and planned for to ensure the plant performance meets the design expectations. The site is well equipped with common as well as advanced instrumentation. It currently boasts the largest number of Blue Cube MQi (mineral quantifier inline) slurry grade analysers on a single plant worldwide. It was also decided that 25 Blue Cube TempoTracks would be installed on the flotation cells. The TempoTracks provide information on froth height and velocity, hence giving continuous, quantitative measurements of the froth that is pulled off each cell, rather than relying on infrequent, subjective visual inspections.The Nova concentrator consists of a differential flotation circuit whereby copper bearing mineral are selectively floated prior to nickel flotation. It is imperative that losses of copper to the nickel circuit, and vice versa, are minimised. The plant metallurgical team and Process IQ collaborated to develop and implement the advanced control strategy for the plant. This paper focusses on the optimisation of the copper concentrate that is pulled off the copper rougher and scavengers. This strategy was made possible by the additional measurements listed above. The control optimisation of the copper rougher and copper rougher scavenger circuit was implemented during August 2017 on the StarCSTM advanced control platform. It continuously optimises the level and air setpoints. The control philosophy incorporates several notable techniques which include: a variable mass pull target that is a function of the quantity and grade of material entering the circuit, integrated compensation to prevent inventory build-up in cells, balancing of the froth velocity over the lip of each cell to adaptive, modular system usage and advanced error handling. CITATION:Gomes-Sebastiaõ, G A, Hearne, Z, Lam, S, van der Spuy, D, Thompson, M and Vines, N, 2018. Nova copper-nickel project optimisation of the copper rougher-scavenger circuit through advanced measurement and control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 77–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By H. G. Wang

The production process of a coal mine can often be interrupted by all kinds of events scheduled or unscheduled and thus often needs gas drainage for a temporary or long-term sealed area. Gas drainage has a relatively high risk, therefore attention must be paid to its design to keep the process safe. Based on the conservation laws of mass and constituents, and under the conditions of the allowable gas concentration limit in the return air route, the relationship between gas concentration and gas drainage flow rate as a function of time during the drainage process is discussed in detail to build a mathematical model of gas drainage from a sealed area. With respect to the gas drainage process, two different conditions need to be considered: one with a methane free fresh air supply, the other with a low gas concentration. This paper presents the derived mathematical models for these situations and then shows that they can be incorporated into one model with some modification. This combined model can be employed to determine the optimum gas drainage flow rate with the shortest drainage time. The application is coded using the C# programming language within the .NET framework. Finally, the application program developed by the author is used to validate the mathematical model through an example of gas drainage with varying rate.

Aug 1, 2013

By William Gleason

For the first time in many years, the Liebherr Group chose to host its annual conference for the international construction trade press in the United States. The reason for the move is simple ? mining. Like other large corporations, especially those in the construction fields, Liebherr felt the effects of the global economic crisis that began in 2008. The slowdown in the housing market was especially hard on Liebherr?s mobile crane and earth moving divisions. The mining division, however, while affected by crashing commodity prices that led to cancelled orders and the loss of financing for some customers, was not battered as badly as the other divisions. And now, with the price of commodities once again on the rise, it seems that it will be Liebherr?s largest machines that lead the family-owned company to better days. ?We can report that our generally optimistic view during the crisis has proved adequate,? said Joachim Janka, president of Liebherr mining equipment, at the conference in Williamsburg, VA, just down the road from the company?s mining truck division global headquarters in Newport News, VA. ?Since the third quarter of 2009, our mining equipment activities have been recording once more a strong and steady demand. This has already yielded a substantial increase in market shares for our product lines of large mining shovels as well as for mining trucks.?

Jan 1, 2011

By Milton Fies

Introduction The first experiment in underground gasification of coal in the United States was conducted at Gorgas, Walker county, Alabama, under a co-operative arrangement between the U.S. Bureau of Mines and the Alabama Power Company, at the suggestion of the Power Company. The test was conducted on property of the Alabama Power Company, that owns some 19,000 acres of coal-bearing lands on which there is developed a highly mechanized mine producing some 2,500 cons of good quality steam coal per day. At the same locality ?there is a 200,000 kilowatt steam plant one of the largest in the southern portion of the United States. The Alabama Power Company owes much of its beginning in 1912 to British vision and courage. The original plans for building hydroelectric plants in Alabama, and for the construction of necessary transmission lines, were submitted to Sperling & Company, bankers of London, who agreed to underwrite certain bond issues, the proceeds of which would be used in launching the new Company on its programme. The set-up by which these funds from England were received was through an intermediary Canadian company, which the English investors desired. The Canadian company - Alabama Traction, Light and Power Company, Ltd. became owner of the securities of the Alabama Power Company and marketed its own securities through the banking house of Sperling & Company. Without assistance at this time the Alabama Power Company could not have gone ahead with its programme of expansion and the bringing together of the properties necessary for laying the foundation for a strong Company, fortified with ample power resources essential for future requirements and for dependable service to the public.

Jan 1, 1948

Mines in the future deliver a paradigm shift in the way mining, material handling and processing are performed, unlocking significant value through production efficiency, flexibility and lower costs and enabling substantial safety and environmental benefits (V Schweikart). Mines in the future are highly productive, with low production costs and are significantly safer. They operate with a skeleton crew and use intelligent systems that fuse information from field instrumentation and other sources to generate the most efficient operating environment. Automated systems are seamlessly integrated across the mine and across the corporate enterprise. Geological models, long-term and short-term plans create optimised production schedules, suitably generated by the mine simulator. Production schedules are shared with the operations management system for deployment mainly by remotely operated and autonomous equipment. As the schedule is implemented, information is collected and shared with various plans, schedules, models and optimisation programs. This production environment is managed in real time from a æCentral Operations CentreÆ and it is visible across the business providing fast and accurate information about productivity, machine condition and environmental conditions. Central Operations Centres also house teams of subject matter experts that monitor and manage the mines and are able to communicate directly with the skeleton crew in the field. Constraints across the production line are displayed and managed appropriately from this location to maximise throughput. Maintenance is interactive and predictive. Reliability specialists in Central Operations Centres monitor the status of machinery and equipment and adjust maintenance plans and strategies to suit. Mining businesses rely heavily on knowledge workers û people with considerable knowledge and learning û and by manual workers. This new knowledge workforce is a team of associates rather than of bosses and subordinates. Field experts become leaders with tremendous autonomy regarding their work. The former line hierarchy becomes a support structure, intervening only in extreme emergencies; instead of giving orders, they are now removing barriers, expediting resources, conducting studies and acting as consultants.

Jan 1, 2009

By E. T. Dumble

Introduction..........914 I. Topography,........915 The Nueces Basin........915 The Coastal Slope...........918 Streams..........919 II. Geology..........921 Eocene..........923 Basal Beds .......923 Lignitic Stage........923 Atascosa Sections......924 International and Great Northern Sections .. . 928 Leona Sections.......929 Nueces Sections....929 Rio Grande Sections.....930 Lower Claiborne Stage......932 Marine Beds ........933 Atascosa Sections....... 933 International and Great Northern Sections .. . 934 Frio County Sections,.....935 Rio Grande Sections.....936 Yegua Clays........938 Atascosa Sections......938 Tilden Sections.......941 International and Great Northern Sections .. . 942 Rio Grande Sections.....942 Fayette Sands........945 Atascosa Sections......946 Tilden Sections......948 Rio Grande Sections.....950 Frio Clays........953 Atascosa-Frio Sections.....953 Tilden-San Diego Sections....955 Rio Grande Sections......955 Neocene ....966 Oakville Beds.......957 Lapara Beds,....... 987 Nueces Sections......958 Bartlett's Ford Sections.....959 Fort Merrill Section......963 Lapara Sections,.....964 Tilden-San Diego Section.....967 Lee Tiendas.......969

Jan 1, 1903

By Vitor Fonseca de Barcelos, Jair Carlos Koppe

Our society is experiencing a digital revolution. Technology is demonstrating its significant potential for mining industry. In this paper are presented the measured and estimated impacts of applying new technologies on blasting operations in a copper mine.

Feb 1, 2020

By E. J. Eisenach, Edward Matsen

AT the present time the Climax Molybdenum Co. is the largest molybdenum producer in the world and the operator of the largest underground mine in North America. It has grown steadily and rapidly since its beginning in 1917. Only 250,000 lb of MoS2 were produced during the first year from 1917 to 1918 when the company was formed. Operations were suspended shortly thereafter because of the lack of a market and knowledge of the uses of molybdenum. During World War I it was used as a substitute for some rare metals and for minor chemical purposes. After 5 years of intensive research and sales promotion, Climax metallurgists succeeded in finding proper applications for the newly discovered metal and the mine was reopened in 1924. Demand for molybdenum increased gradually and in 1930, 3.5 million lb of MoS2 were produced. In the meantime, research work for additional uses of molybdenum continued until it had established itself as one of the most important alloying elements in producing high quality steels. After the start of World War 11, from January 1942 to October 1953, 43 million tons of molybdenum ore were mined and 484 million lb of MoS2 were produced. Climax mine is located in Colorado, 100 miles southwest of Denver and 12 miles northeast of Leadville on the Continental Divide of the Rocky Mountains. The principal mine workings range from 11,170 to 12,000 ft in elevation. Topographically, it lies in the base of a large cirque that is surrounded by Mt. Bartlett to the north, Clinton Peak and McNamee Peak to the east and Ceresco Ridge to the south. This cirque opens to the west and to the Ten Mile Valley.

Jan 3, 1954

By P Craig, I Canbulat, J Naylor, J Emery, A Sykes

Longwall mining is by far the most common method of underground coal extraction in Australia. Industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. Longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin-encapsulated bolt installation is still the principal method used in all major coal producing countries around the world. Anglo American realised that an opportunity existed to introduce an alternative roof bolt installation technique called ‘spin-to-stall’ (STS) into Australia. STS was first introduced by Anglo American Coal in South Africa, where it has been successfully used for over a decade, though implementation of South African STS resin in Australia has proven to be near impossible. Therefore, a new STS development project was initiated between Anglo American Coal and Jennmar Australia. This paper summarises the journey of this project, the results achieved and the successful implementation of STS at Grasstree mine.CITATION:Emery, J, Canbulat, I, Craig, P, Naylor, J and Sykes, A, 2014. Development and implementation of spin-to-stall resin at Anglo American’s Australian Underground Coal Operations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Luigi Giacomini, Bruce Kiefer

A new plant for special steel long products was commissioned in recent years at Dangjin, South Korea, for Hyundai Steel. Two multi-line rolling mills can produce yearly 1 million tons of billets, straight and coiled bars, with dimensions from 5.5 to 350 millimeters. The products are used for manufacturing engine and transmission components used by Hyundai Kia Automotive Group. The processed grades include carbon, special alloy, spring, bearing and free-cutting steel. The first mill rolls blooms into finished large round and square products, as well as into intermediate billets. A 2-high reversing breakdown stand is followed by a finishing and sizing train with CGA stands equipped with an under-load roll parting system for automatic gap control. The second mill combines lines of small bars, rods and bars-in-coil. Billets are rolled in a continuous rolling mill with original RedRing Series 5 stands. The rod outlet features Morgan No-Twist and Rod Reducing/Sizing mills, Morgan High-Speed Laying Head and Stelmor conveyor. Advanced sensors and electronics integrate with mechatronic packages, thus equipping the mill for Industry 4.0 applications. Hyundai can meet the demanding requirements posed by the automotive industry and benefit from optimized conversion costs, the flexibility to meet market changes, achieve high product quality, and reduce floor personnel.

Oct 1, 2019

By Earl F. Hastings

The Pilgrim mine, operated by the Pioneer Gold Mining Co., is 9-1/2 miles west of Chloride in the Pilgrim mining district on the eastern slope of the Black Mountains, or River Range, Mohave County, Ariz. In March 1937, 100 tons of gold ore per day were being mined and milled at the property by a total force of 5i men. Climatic conditions allow year-round operations. Due to present activity in the county there is an ample supply of labor for the requirements of the mine. The Pilgrim is the only producing property within s radius of 6 miles; recently, however, the South Pilgrim Mining Co. has launched a development campaign on claims that adjoin the Pioneer Co. property to the south.

Jan 1, 1937

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007

By F. T. Rabbitts

Introduction When the investigation of radioactive ores began at the Mines Branch about five years ago it was at once evident that improved chemical methods for the determination of uranium were essential. The published methods available were time-consuming and insensitive and were lacking in accuracy and precision. It was desirable to obtain methods which would be rapid, sensitive, and accurate. They should also allow for the possible presence of any interfering elements and should be adaptable to routine analysis by technicians. Chemical methods are necessary to provide standard analysed samples for counting and to check analyses by counter methods. Moreover, counter methods cannot be used, and only chemical methods are suitable, when the sample is not in equilibrium, as with weathered minerals and leach residues. As leaching processes are improved, more sensitive chemical methods are required for the increasingly lower content of uranium in the leached residues. When the leaching process reaches the plant stage, speed of analysis becomes more important, without sacrificing accuracy. The purpose of this paper is to describe briefly .the methods used at the Mines Branch for the chemical analysis of uranium in ores. These methods represent the results of investigations by a number of groups in the United Kingdom, the United States, and Canada.

Jan 1, 1952

By Lee J. Raabe

A specialized loading system for tensile and fatigue testing of wire rope was constructed and installed in the U.S. Bureau of Mine Wire Rope Test Facility in Bruceton, Pennsylvania. The computer-controlled closed-loop servo-hydraulic test system which can apply up to 800,000 pounds of force on the rope while stretching it up to 30 inches will be used in the development and verification of hoist rope retirement criteria for ropes in the 1 to 2 ½ in. diameter range. Characteristics and capabilities of the system are discussed.

Jan 1, 1984

By T Raynlyn, A Edenton, M Adam, R J. Holmes, J R. Manuel, N Ware, R Smyth

Due to ongoing demand and increasing depletion of high-grade iron ore resources from large deposits, Australian iron ore producers are developing smaller size deposits to maintain current export levels. The iron grade, mineralogy, chemical and physical characteristics of iron ore fines being mined from different deposits vary considerably. It is therefore imperative to develop long-term strategies to maintain the quality and consistency of iron ore fines while moving to a larger diversity of smaller deposits. Blending is a common practice in sinter plants as it is almost impossible to produce a high performance sinter mixture displaying the required characteristics from one single ore. Blending is also one of the most effective options being used by iron ore producers to ensure the long-term stability of their products while increasing production. When designing a blend, the blend components are selected to support each other to achieve the required overall balanced metallurgical performance of the final product at a relatively low cost. To do so, a fundamental understanding of the key characteristics of iron ore fines and their potential impacts on the iron ore sintering process and sinter quality are required. In this paper, the sintering process and sinter structure have been analysed and the key factors affecting the sintering performance of iron ore fines, including productivity and quality, identified. Under fixed sintering conditions, the granulation efficiency, nuclei stability and the volume and properties of the primary sinter melt are believed to have important impacts on both sintering productivity and sinter quality. Discussion is then focused on the effects of ore chemical, physical and mineralogical characteristics on the key factors identified and in turn the consequences for sintering productivity and sinter quality.

Jan 1, 2009