Search Documents

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

By Richard A. Winters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,680-acre Lime Canyon Wilderness Study Area (NV-050-231) to evaluate its identified mineral resources. The Wilderness Study Area is in Clark County, NV, about 30 air miles southwest of Mesquite, NV. The area studied contains an estimated 44 million tons of indicated subeconomic resources of gypsum, an inferred subeconimic resource of limestone and dolomite, and occurrences of gold, copper, uranium, and zeolite. The Wilderness Study Area is underlain chiefly by carbonate rocks with lesser amounts of sandstone and shale. Metamorphic, granitic, and volcanic rocks also crop out within the area. Large portions of the area are overlain by alluvium. The Wilderness Study Area is within the Gold Butte mining district. Several gold mines with past production are nearby to the south of the Wilderness Study Area; one mine is reported in operation on a small scale. Several silver-bearing copper and zinc mines with past production are nearby to the east of the Wilderness Study Area

Jan 1, 1988

By K. K. Kelley

Thermodynamics data for silicates have applications in the fields of extractive metallurgy, ceramics, and geochemistry. To facilitate these applications, up-to-date tables of heats and free energies of formation are needed. It is the purpose of this report to supply such tables for anhydrous silicates. During the last 15 years the heats of formation of a substantial number of anhydrous silicates have been reliably determined at or near room temperature. This resulted from the development (first by the Bureau of Mines and later by the Geophysical Laboratory of the Carnegie Institution of Washington, by the Institute of Geology of the University of Helsinki, Finland, and by the Department of Geology of the University of Chicago) of accurate solution calorimeters, employing hydrofluoric acid as the reaction medium. Specific references to work of these laboratories will be made in the next section of this report. Also, entropy data at 298.150 K. and high-temperature heat-content values are available for many of these silicates, mainly owing to work of the Bureau of Mines. Most of these entropy and heat-content data have been compiled in Bureau of Mines Bulletins (13, 15).3

Jan 1, 1962

By C Zschiesche, alam, A Abadias Llamas, A K

An integrated experimental and thermodynamic modelling study of the phase equilibria in the FeOFeO1.5- SbO1.5-SiO2 system in equilibrium with liquid Sb and Sb-Ag metal has been undertaken to develop thermodynamic model of the Na-Si-Fe-O slag system with S-Sn-Sb-Pb-As minor elements based on the experimental investigation of the selected sub-systems. New experimental phase equilibria data at 575–1600°C were obtained for this system using high-temperature equilibration of synthetic mixtures with predetermined compositions in sealed silica ampoules, Fe3O4 basket in sealed silica ampoule, or Re foils, a rapid quenching technique, and electron probe X-ray microanalysis of the equilibrated phase compositions. Experimental results on phase equilibria in the Fe-Sb-Si-O+Sb metal system obtained helped to produce initial set of model parameters in the slag. The primary phase fields of quartz/tridymite/cristobalite (SiO2), 2 high-SiO2 immiscible liquids, olivine (Fe2SiO4), wustite (FeO1+x), spinel (Fe3O4), schafarzikite (FeSb2O4) and valentinite/ senarmontite (Sb2O3) were identified in the binary Sb2O3-FeO, Sb2O3-SiO2 and ternary FeO-Sb2O3- SiO2 systems. Further refinement, particularly the distribution of excess Gibbs energy among the ‘FeO’-Sb2O3-SiO2 and ‘FeO1.5’-Sb2O3-SiO2 interactions, required the study at more oxidising conditions. Oxygen potential was increased using an inert metal (Ag) rather than using the gas flow due to the high volatility of Sb-containing gaseous species. Liquid Ag-Sb alloys with low concentrations of Sb of a few percent were used. At these conditions, the concentration of AgO0.5 in slag was below 1 mol per cent, which had a small effect on observed phase equilibria in the system. In addition, important information on the solubility of silver in slags is produced, which can be valuable when treating electronic recycling materials or primary silver-containing ores through the Pb process. Two main areas were addressed: the spinel-tridymite boundary (40–70 per cent SiO2 in slag) and spinel liquidus near 15 per cent SiO2 in slag. This allowed to deconvolute the separate contributions of the FeO-Sb2O3(-SiO2) and Fe2O3-Sb2O3(-SiO2) systems.

Jun 17, 2024

By Rune Gammelsmter

Turbulent chemically reacting flows are generally very complex, involving interactions of chemical, thermodynamic, and fluid mechanical processes. A combustion model based oh algebraic moment closure has been developed. The model is applicable for reaction rates where the chemical kinetics can vary from slow to fast. The effects of turbulence is taken into account by means of modifications to the well known k-e modelling procedure. The model is applied to an industrial combustion process. Calculation of furnace off-gas combustion from an aluminum reduction cell has been performed. The theoretical results agree well with experimental values.

Jan 1, 1992

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By D. Moronkeji, R. Maharidge, D. A. Curry, B. J. Davis, U. Prasad, J. Franquet

"Proper shale characterization is crucial in shale gas drilling, exploration, completion and production. Unlike porous sandstone and carbonate reservoirs, the challenge with shales comes from their micro- to nano-darcy permeability ranges and the anisotropy of their mechanical and hydraulic properties. Most porosity-dependent logs are not sensitive enough to capture the true behavior of shales. Consequently, mineralogy and other strength and stiffness-related properties must be determined to characterize magnitudes and variances in shale mechanical and flow properties. In addition, these properties must pass quality assurance/quality control (QA/QC) practices to give confidence in their use in subsequent log calibrations, during geomechanical modeling, or in fracture design models. This paper presents a technique to integrate shale properties that are measured by various methods, and a methodology to perform QA/QC on the data before application.Shale properties originate from various sources, including downhole and laboratory measurements. Physical samples for laboratory testing are usually limited to a few depths. Lab tests are often costly, and replicating in-situ conditions can be difficult or impossible. In addition, results frequently show wide scatter, reflecting inherent depth variability and lateral heterogeneity. Wireline logs provide nearcontinuous data, but rarely yield direct measurements of rock strength properties. Although geomechanical and fracture models use log data, calibrating it with reliable and previously verified lab-measured properties is important. This paper presents a process to perform QA/QC on lab-measured data using various crossplots.Ten mechanical, microstructural and physical properties are graphically displayed to visually characterize shale strength behavior in ambient and in-situ conditions, whether measured or modeled statically or dynamically. These properties are often sourced from different departments. The properties are integrated but are individually subject to the previously mentioned uncertainties. Pairs of property values are crossplotted and compared with correlations from the literature or previously established with qualified data from related formations. Conformance with these correlations gives confidence in the data, whereas outliers are flagged as questionable. Repeating the process with questionable data crossplotted against other parameters for the same depth highlights the property with the greatest uncertainty. The determination of its value is investigated to locate the source of the inconsistency and establish a more reliable value. Where this is not possible, the user has a rational basis for rejecting that property value."

Jan 1, 2015

By W. W. Beaton

The Coxheath copper mine is situated on the north side of the Coxheath hills and opposite the French Vale, at a distance of about 10 miles southwest of Sydney, Cape Breton county. The deposit was discovered in 1880, and the first work on the property was carried out with local capital. Lacer some Boston men became interested and formed a Company to finance the undertaking. This group operated the mine intermittently for approximately 20 years, spending close to one million dollars on the undertaking. Three shafts were sunk to depths of 110, 190, and 340 feet, and further underground workings to the extent of approximately one-half mile were driven. Also, an extensive surface programme was carried out. in which many test pits and hundreds of feet of trenches were dug, Early in the summer of 1928 the Arno Mines, Limited, optioned the property and immediately started an exploration campaign. A series of trenches were dug along the parallel vein system, and over 4,000 feet of diamond-drilling was done. The results obtained were so encouraging that a mining plant was erected in the fall of chat year and No. 2 shaft was drained. A complete new plant was installed, consisting of one 120 h.p. Fairbanks-Morse Diesel engine, direct connected to a Sullivan angle compound, air compressor; an 80 h .p. Leonard boiler, which supplies power for the 7 by 11 Ingersoll-Rand hoist; and a Sullivan class C steel sharpener and oil furnace. Two 250-gallon Cameron pumps, one operated by steam and the other by air, were placed in the mine so that, in case of a break-down, the mine would not be flooded.

Jan 1, 1930

By T. Donkin, B. Patterson, M. I. Guthrie, J. T. Ross

"The interest in the use of sensor-based particle ore sorting has increased significantly with the recent advances in the sorting technologies and higher capacities per unit. This technology has the potential to provide great value in processing lower grade ores from the mine whilst delivering higher grades to the mill as well as in upgrading waste rock into ore. Typically, the focus is on the amenability of the ore to ore-sorting and associated reductions in the consumption of energy, water and consumables. However, layout has a significant impact on the installed cost of a concentrator and the layout impacts from fitting an ore-sorting circuit into the concentrator plan need to be carefully considered. This paper examines layout considerations that play an important role in ore sorting projects. These include additional crushing and screening requirement, transportation of the rejected material back to the waste stockpile (mine fleet requirements) and effects on concentrator footprints.INRODUCTION Ore sorting has been practiced throughout history with an early report by Agricola in 1556. Metallic and non-metallic minerals were extracted from rocks by laboriously breaking them with hammers and picks and hand-picking selected material with higher grade off a table. The concept has not changed but the sorting technology has evolved significantly over the last 20 years. Ore sorting is usually a dry process in which a portion of the material is rejected based on mineral properties and/or grade. The methods used for sensing ore particles cover a large range of physical properties. A variety of sensors are available that differ on the discrimination technique that is used, which include: photometry, radiometry, conductivity, magnetism, microwave, X-ray transparency: X-ray transparency and luminescence and UV fluorescence (Sivamohan and Forssberg, 1991; Wotruba, 2006). There are two main ore sorting techniques: particle ore sorting and bulk ore sorting. According to Nadolski et al (2018), the potential for sorting is determined though analysis of grade heterogeneity within the orebody (greater heterogeneity represents more opportunity to add value to a project) at the scale of the intended sorting unit size."

Jan 1, 2019

By Alexander M. Gow

This paper summarizes a survey of fine-grinding practice in ore-concentrating plants throughout the United States, Alaska, Canada, Mexico, and Cuba as reported in the Bureau of Mines Information Circulars on milling methods. The survey covers 49 concentrators, which have a combined capacity of over 160,000 tons per day. In these plants 470 ball, rod, and pebble mills prepare material for flotation, gravity concentration, amalgamation, cyanidation, and air separation. The ores are those of gold, silver, copper, lead, zinc, molybdenum, feldspar, and pyrite. The metallurgy is that of the period 1928-32. Of these 49 concentrators, 36 are in the United States. They can treat 134,400 tons per day, and they have 326 fine-grinding mills. In the United States there are about 100 active or temporarily idle concentrators, exclusive of the many plants in the Tri-State zinc district, the washeries of the Lake Superior iron ranges and the Florida phosphate area, and small gold and silver concentrators. These 100 plants have an estimated capacity of 290,000 tons per day and employ about 650 ball, rod, and pebble mills. Consequently, since this paper covers about half of the production of this country it may be considered as particularly representative of fine grinding in ore mills in the United States.

Jan 1, 1933

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By Lloyd Litwin

The ARTA 2008 Project (Alpha Ridge Test of Appurtenance) was a Canadian Government sponsored deep water seismic survey carried out on the high arctic permanent polar ice cap. This Geological Survey of Canada operation was the second seismic research project in the high Arctic and was monitored by the Danish Government. Utilizing 100% air support from Eureka and then helicopters from an ice based tent camp north of Ellesmere Island, the five week study was accomplished in the early spring just after the sun returned to the far north.

Jan 1, 2011

By J. C. Cawley

Improvements in today's maintenance practices are mandatory as more complex and productive machines evolve in the mining industry. By keeping machine reliability high, through improved maintenance procedures, overall mining costs can be reduced. The Bureau of Mines is investigating diagnostic maintenance systems for underground mining machinery. A hydraulic expert diagnostic system and an electric motor predictive diagnostic system have been designed and installed on a Joy 16CM continuous miner. An electrical diagnostic system has been designed and installed on a Joy 14CM continuous miner. Each system is functionally described and the relative merits of expert diagnostic systems versus algorithmic diagnostic systems are discussed.

Jan 1, 1991

By Russell R. Trengove

In order to extend or delimit the known ore reserves adjacent to the Comet Coalition property on the western slope of the Highland Peak Range about 8 airline miles west of Pioche, Nev., the Bureau of Mines undertook an exploration project of diamond drilling. Production figures from this property, formerly known as the Schodde, are not available, but it has been reported that small amounts of rich silver and gold ore were Shipped by wagon to a smelter in the Salt Lake valley during 1900-1910. Small shipments were reported for the period 1915-1927, also. A study of the Pioche District by the Federal Geological Survey in 1942 and 1943 was the basis for the exploration program of the Bureau of Mines in 1947 This program consisted of diamond-drilling three holes. The total footage was 2,967 feet. No. 1 hole was drilled 1,260 feet, a record depth for diamond drilling in the Pioche District. Silver-bearing lead-zinc sulfide ores are found in the Combined Metals limestone, known locally as the C.M. bed, These deposits have been formed by replacement of the limestone that is inclosed in the Pioche shale.

Jan 1, 1949

By C. B. Kenahan

The Bureau of Mines is developing methods for reclaiming the metal and mineral values contained in municipal incinerator residues. This report describes the first phase of the research, in which reliable methods for sampling and analyzing municipal residues were established and the composition and characteristics of the residues were determined. Samples were obtained from a variety of grate-type furnaces and also from a rotary kiln furnace. The samples were processed on a batch basis and separated into their natural categories by a variety of methods including screening, magnetic separation, air separation techniques, and handpicking. The main components of the residues were determined to be metal and metal oxides, glass, and ash.

Jan 1, 1968

By J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) slip along steeply dipping faults and (2) fracturing of strong strata above, or below, the coal seam. Both failure modes produce dynamic or ?shock? loads on the perimeter (roof, rib, floor) of mine openings. Special consideration should be given to these failure modes in planning of deep coal mines since their occurrence is not within the professional experience of many contemporary workers, and their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By Leena Suopajärvi, Karin Käär, Marcin Szumny, Jari Joutsenvaara, Md Ariful Islam, Helmut Mischo, Georg Meissner, Ossi Kotavaara, Catalina Vrabie

This study outlines implemented tactics and results for community empowerment through participation in questionnaire surveys, educational programs, and discussion on sustainable sourcing from new critical raw materials (CRMs) projects. Utilising questionnaire surveys, including the Public Participation Geographic Information System (PPGIS), the research gathered public opinions from Estonia, Germany, Poland, and Zambia, receiving 1,068 responses. These responses addressed various social, economic, and environmental issues related to CRM projects. Feedback from educational courses with participants from over 25 nations and public events provided additional insights. The collected data and feedback offer crucial input for advancing sustainable and responsible CRM sourcing strategies in these regions.

Feb 1, 2025

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By Hiroyuki. Fukuyama

The pseudo-binary phase diagram of the cuspidine (3CaO2?SiO2?CaF2) - CaF2 system has been studied by electron probe microanalysis (EPMA) and X-ray diffractometry (XRD). To prevent fluorine loss in the form of a HF gas by a reaction of CaF2 with water vapor at elevated temperatures, the equilibrium experiments were conducted with the sample hermetically sealed in a platinum tube. By employing this technique, it was successfully revealed that cuspidine exists as a stable phase and congruently melts at 1684 ± 1 K, and the cuspidine - CaF2 system presents a simple eutectic type of phase diagram, of which eutectic temperature has been estimated to be around 1540 K, corresponding to the composition of 40 mass% 3CaO?2SiO2 - 60 mass% CaF2?

Jan 1, 1999

By G Balog, T Ormerod, D Sidea

Carrapateena is a copper-gold sub level caving operation located in the Gawler Craton, South Australia. One of Australia’s largest undeveloped copper deposits, the project will be a 4.25 Mtpa underground operation, with an estimated mine life of 20 years (OZ Minerals, 2017). First concentrate production was achieved in December 2019, within the Iron Ore Copper Gold (IOCG) hematite breccia complex. The Carrapateena orebody is overlain by 500 m of barren sediments of the Stuart Shelf, which hosts two aquifers. The cover sequence is dominated by shales, quartzites and sandstones in order of thickness. The cover sequence presented challenges to the mine ventilation system as a result of highly variable rock strengths. On this basis, the site developed the first vent rise, Vent Rise 5 (VR5), earlier than required as a means to test the empirical stability assessment. Assessment for VR5 was completed in 2017, with the mine yet to develop through much of the cover sequence. Due to the geotechnical data available at the time, it was anticipated that break out would occur within the vent rise walls as a function of the low strength Woomera shales. VR5 was developed to 4.5 mᴓ in late 2018. The timing of the VR5 development enabled the site technical team to calibrate empirical stability factors for the assessment of future vent rises. At the time of writing, four additional vent rises have been successfully developed to a diameter of 5.5 m. No significant overbreak has been observed within any of the vent rises. This paper is intended for geotechnical practitioners designing large-diameter vent rises in geological environments similar to the Stuart Shelf where a similar approach to vent rise design may be warranted.

Mar 15, 2021