Search Documents

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests.

Jan 1, 1957

By Jim McKinley

With a growing number of mines reaching closure and seeing closure costs materialize, regulators, lenders, and banks are observing projects that fail economically by miscalculating these costs. Mine closure costs are often categorized as a type of liability which is defined as the money owed by the company to offset effects from the project, and the money available to pay for those debts (e.g., bond). Often, decisions made before Day 1 of mining (e.g., co-disposal, dry stack tailings, waste segregation) can significantly change the bond calculation. Once the bond is calculated and funded, operators are encouraged to conduct closure research and use applied science for progressive bond release prior to final closure. However, this author has observed few instances of financially significant progressive bond release, as there are typically no robust procedures for bond return, either before or during closure activities. As a result, many companies decide that entering a state of Care & Maintenance (C&M) is less risky than attempting to fund closure activities with an unknown bond return mechanism. Although perhaps less risky in the short-term, the primary long-term risk with entering C&M is that it increases the chances of the bond not covering the cost of closure and the chances of the government/regulatory agency inheriting the mine closure. Bonds are typically reevaluated on a regular cycle (e.g., five years) so every mining company goes through this financing challenge eventually.

Feb 22, 2026

By K. Östcrdahl

We are developing a cost-saving and environmentally friendly process with low energy consumption to recover the metal content and recycle the acid from spent pickle baths. The metals are precipitated as metal fluorides, which can be turned into metal oxides and hydrofluoric acid by thermal hydrolysis. In the proposed process the solution is concentrated by nanofiltration and the metals are precipitated in a subsequent crystallization step. Different nanofiltration membranes have been evaluated in experimental batch tests. The membrane MPF-34 from Koch Membrane Systems offered both good flux and acceptable metal retention even after long periods of acid storage. The solubility of B-FeF3.3H20 has been measured at varying acid concentrations and at different temperatures. The solubility decreases with increasing hydrofluoric acid and nitric acid concentrations. This suggests that the crystallization process should be operated at high acid concentrations. The crystal growth rate of B-FeF3.3H2O is found to be quite low but increases significantly with temperature. This suggests that the crystallization process should be operated at higher temperatures (40 - 60°C). Within the project a pilot plant has been constructed where the spent pickle bath solution is concentrated by nanofiltration to the desired metal fluoride supersaturation, and B-FeF3.3H2O is crystallized in a 10 L continuous crystallizer.

Jan 1, 2006

By Raymond B. Ladoo

[Inquiries are frequently received by the Bureau of Minas relative to occurrence, mining, treatment and utilization of the natural hydrocarbons' such as gilsonite, elaterate, wurtzilite, grahamite, and ozokerite although have been known and used for many years, they are not yet well understood and the amount of recent literature dealing with them as comparatively small. This paper is intended merely to summarize the present knowledge The natural hydrocarbons included in this series are gilsonite, elaterite, wurtzilite, glance pitch, manjak, grahamite, albertite, arid ozokerite and many other minor varieties. With the exception of ozokerite and the other mineral waxes, then all more or less resemble asphalt in that they are dark brown or black bituminous substances of organic origin, generally with a resinous luster. Ozokerite usually light an color with a waxey luster, is closely allied to the others of the series, but is usually considered separately, Unfortunately authorities differ as to nomenclature so that determinations of physical and chemical properties from different sources may riot be readily compared. Abraham Herbert, Asphalts and Allied Substances, 1918, 606 pp. has made one of the most detailed studies of these subjects in recent years, and his classification is used in the main. The following definitions are given by him]

Jan 1, 1920

By Jackson G. Jenkins

Magma Copper Company's San Manuel SX-EW facility has operated since May, 1986. The original facility had a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solution from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing in-situ leach solutions. This paper focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research utilizing surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1993

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

By Stephen Meyer, Véronique Falmagne, Antti Pyy

Kittilä Mine is a gold mine located in Northern Finland, owned and operated by Agnico Eagle Finland. The mining operation started in 2008 with open pits which were completed in 2012 and production moved to being entirely underground. The mine consists of four separate orebodies, currently producing 2.0 Mt per annum, and requiring over 19 km of development on a yearly basis. The principal mining method is long hole stoping with delayed backfill. Microseismic monitoring was initially tested in the Suuri orebody, in the mining block between the 625 and 500 Levels. A small monitoring system was installed in 2018, after observations of stress-induced damage to the rock mass and in anticipation of future mining at greater depth. The initial goals were to evaluate if useful data could be recorded and test the signal quality of different sensor types. Prior to 2018, ground control related challenges in the Suuri and Roura mining blocks had been mostly related to sill pillar mining and block movements between weak graphitic schist planes. Seismic monitoring in the Suuri deposit proved successful for following the rock mass response to mining and helped support the rationale for early monitoring in the new, deeper mining block in Rimpi at 900 m depth. Preliminary geotechnical characterization and testing of the rock mass showed areas of silicification in the footwall rocks with potentially continuous structural features. Seismic monitoring of the Rimpi area has confirmed the brittle behavior of the rock mass, with strong seismic responses induced by stress changes following blasting being recorded. In addition to this expected behavior, a large magnitude event associated with significant damage in the footwall drive development 90 m above the stoping was experienced. Initial investigation of the rockburst showed two separate damage locations with over 300 tons of displaced rock. The seismic monitoring system recorded this rockburst as a single seismic event with magnitude significantly larger than previously recorded. Additional analyses indicated a possible thrust fault event, triggering two separate strainbursts. Following this event, the ground support system was upgraded in parts of the footwall drives to improve dynamic capacity. Systematic calculation of the source mechanisms for the small footwall events down to Mw-2.5 has revealed potential planar structures in the footwall. Early implementation of microseismic

Apr 26, 2022

By G. Asbjörnsson, E. Hulthén, P. Papadopoulou, C. M. Evertsson

Crushing plant managers need to assess, manage, and communicate the environmental impact induced by their crushing plant operations as a step towards the sustainable development of the company. However, performing reliable environmental impact calculations of crushing plants can be challenging when the availability of operational and emission data is low, and when the company’s environmental expertise is not adapted and connected to plant operations (or does not currently exist). To address these challenges, this paper proposes a practical approach where the lifecycle assessment methodology (LCA) is combined with process simulations in a web-based tool. To describe what functionality such a tool should have to be incorporated into a company’s workflow, the system that surrounds a crushing plant is analysed. Further, a case study with a three-stage crushing plant is introduced to showcase how the simulated power draw results produced with the beta version of the tool can be compared to measured sensor data from the crushing plant for one operational day. The results indicate that the simulation tool can provide an adequate estimation of the specific energy for the different material fractions and give an overview of the environmental impact of the process caused by electricity and explosives consumption. Plant managers and operators can use this tool to calculate the environmental impacts of their plant and simulate how different operational strategies influence them. Keywords: LCA, environmental impact, coarse comminution, crushing plant

Jan 1, 2020

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By H. C. Hamontre

[The Bureau of Mines well-bore caliper was designed to provide an instrument that could be operated through 2-inch tubing, which 'a used particularly in many input wells on water-flooding projects of eastern, Kansas and northeastern Oklahoma. It should find wide application elsewhere under many other conditions where it has not been possible previously to make caliper logs with the larger probes used on other instruments. The caliper has three additional advantages over other instruments of this type: (1) It measures 4 radii (up to 18 inches) 90° apart with an accuracy of ± 1/4 inch; (2) the measuring arms can be opened and closed at will by remote control; and (3) it is run and operated on a single-conductor, armored electric cable (Amergraph, type 1-H-0). The caliper probe is 1-3/4 inches in diameter and approximately 6 feet in length. The electrical control and measuring circuits are encased in a stainless-steel tubular case. Measuring arms, made of 5/16-inch aluminum tubing, are attached near the lower end of the instrument. Distances the arms are extended are indicated t the surface by a meter calibrated to read directly in inches. Depths at which the radii measurements are taken are indicated by a wireline depth indicator on the cable-reeling. The instrument is not affected by pressure or temperature, it can be run open hole or under pressure through a lubricator. This paper describes and illustrates the instrument and outlines the operating procedures. A bibliography at the end of the report gives references to articles and patents on the development and use of other well-bore calipers.]

Jan 1, 1954

By Manoj Khandelwal, Jian Zhou, Yingui Qiu, Peixi Yang, Pingan Peng

Rockburst prediction is crucial in deep hard rock mines and tunnels to make safer working conditions. Due to the complex interaction of many factors involved in rockburst prediction, such as multi-variable and multi-interference factors, three hybrid support vector machine (SVM) models optimized by particle swarm optimization (PSO), Harris hawk optimization (HHO), and moth flame optimization (MFO) are proposed to predict rockburst hazard level (RHL). The RHL is determined according to four kinds of microseismic characteristic parameters including angular frequency ratio, total energy, apparent stress, and convexity radius. Then, six types of microseismic characteristic parameters are taken as input variables in 343 sets of data, including angular frequency ratio and total energy, etc.. And the RHL is taken as the output target of rockburst prediction. The classification performance of PSO-SVM, HHO-SVM, and MFO-SVM hybrid models is evaluated by accuracy (ACC), precision (PRE), and kappa coefficient. Findings reveal that the MFO-SVM model performs best in terms of accuracy, with ACC, PRE, and kappa coefficients reaching 0.9559, 0.9063, and 0.9094 respectively, while PSO-SVM and HHO-SVM have similar performances. However, the PSO-SVM, HHO-SVM, and MFO-SVM all perform better than the unoptimized SVM model. This confirms that the three optimization algorithms significantly enhance the rockburst prediction capacity of the SVM model to help mine practitioners apply machine learning methods to rockburst prediction problems appropriately.

Feb 3, 2023

By Ulrich Leiste, David M. Fox

This paper presents the results from small scale testing aimed at measuring the loads on a rigid target due to the detonation of a buried mine. The aim of this research is to find how the impulse delivered to the target varies as the air filled void volume fraction within the soil changes.

Jan 1, 2013

By J. S. Chen

DOE recently funded 21 projects under the solicitation by its Environmental Restoration and Waste Management Division. This project is combining the expertise of an interdisciplinary team of researchers with that of three manufacturers to isolate nuclear waste storage sites using remote longwall mining. The concept is being pursued in Germany, too. This paper will present the conceptual approach to the project and discuss the problems in transferring longwall mining technology to nuclear waste containment.

Jan 1, 1994

By Michael D. Dunn

The Bureau of Mines evaluated a quartz schist formation within the Blue Joint Wilderness Study Area which was identified as having a "high potential" for copper-silver-cobalt-barium resources. Stratiform and remobilized copper occurs near, and bedded barite within, the study area. In addition, the black to gray Proterozoic quartz schist may correlate with the Yellowjacket Formation which contains cobalt-copper-gold-silver deposits at Blackbird, ID, about 30 miles to the south. Eighty soil and 43 rock samples collected across the quartz schist formation were analyzed for gold, silver, copper, cobalt, and barium. During the reconnaissance and sampling, particular attention was given to looking for malachite (copper carbonate) and erythrite (cobalt arsenate, also known as "cobalt bloom"). The sample analyses and geology in this localized area do not provide enough evidence to support the "high potential" designation for copper-silver-cobalt resources. Barium potential still appears high, however.

Jan 1, 1987

By Jas. G. Ross

Introduction Asbestos, a mineral known and used in ancient times, has become an article of commerce only during the life of the older asbestos miners in Quebec. The diversified uses of this adaptable substance are now numbered by the hundreds. Wherever insulation or resistance to heat may be required, asbestos, either by itself or mixed with some other material, may be employed to advantage. Regarded as a curiosity for centuries, it is now in such common use that it is familiar to all. The demand for long fibre for use in the manufacture of textiles and brake-lining, and for shorter fibre for making shingles, paper, and insulation materials, serves to support the industry of mining asbestos-bearing rock and milling the fibre from it in Canada, South Africa, Russia, Cyprus, and the United States. The commercial use of asbestos dates only from 1876, in which year large deposits were discovered in the Province of Quebec, Canada. Prior to that year a small amount of long fibre amphibole asbestos was produced in Italy. Occurrence In Canada In the Eastern Townships of Quebec, along the line of the Quebec Central railway, is an area of serpentine rock. It extends westerly into Vermont and easterly to Gaspe. A part of it, the section from Danville to East Broughton, contains areas in which occur deposits of commercial asbestos fibre of the chrysotile variety. Pits have been opened on some of these deposits at Danville, Coleraine, Black Lake, Thetford Mines, Robertson, and East Broughton. Thetford is distant 68 miles from Quebec city, East Broughton lies 25 miles to the northeast of Thetford, while Danville is 45 miles to the southwest of Thetford.

Jan 1, 1927

By AIME AIME

WHEN "Chief" Buehler in mid-September set out on his official 10,000 mile swing-around-the-circle visiting Local Sections he decided not to tell his audiences how to organize and operate a state geological survey. As the director for 28 years, of the Missouri Bureau of Geology and Mines (which, he concedes, is the best in existence) lie could have done this to good advantage; but he preferred to discuss affairs of the Institute. In 25 speeches made to member and student groups, he dwelt on sonic or all of the following phases of activities. He stressed the vital importance of the Local Sections in providing the opportunity for members to associate under pleasant auspices with others in their profession. The benefits of Institute membership he classified as tangible and intangible. Of the two lie felt that the latter were more important. A man's progress in his profession depends in large measure upon a broad acquaintance and friendship with others. The Institute is incomparably the best medium for meeting fellow engineers. The primary, function of the new enlarged Membership Committee is to obtain a comprehensive list of engineers eligible to be members, always hearing in mind that the standards of membership must not be lowered in any degree. These men are to be invited by individual letter to apply for membership. Whether they become members or not is of less importance; but it is vital that no qualified man should be outside the fold for the reason that membership had never been suggested to him. Dr. Buehler emphasized repeatedly his feeling that the younger man that had never had Institute membership brought specifically to his attention had been cheated:

Jan 1, 1935

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By F Diaz, G Hovestadt, B Friedrich, D Latacz, M Sommerfeld

The metallurgical sector significantly contributes to the global carbon footprint and encounters the challenge of developing more sustainable production methods. This study introduces novel approaches aimed at reducing CO2 emissions within the industrial sector, some of which have been developed up to the demonstration scale. In two case studies, urban waste from the agricultural sector (corn, olives, coconut etc) and waste electrical or electronic equipment (WEEE) recycling residues (shredder light fractions (SLF)) were subjected to thermal treatment. The resulting materials were then used as substitutes for conventional fossil-based reducing agents in both the copper and ferroalloy industries. Furthermore, hydrogen was employed at different scales to assess its efficacy as a reducing agent for recovering metal oxides from fayalitic copper slags. Our findings reveal promising prospects and defined specific challenges for the integration of these alternative reducing agents in the industry. The synergistic use of pyrolysed SLF, bio-coke, and hydrogen presents a viable pathway to significantly diminish CO2 emissions while simultaneously improving the sustainability of the metallurgical sector.

Jun 19, 2024

By L. Rintala, P. Latostenmaa, T. Kalliomäki, O. Forsén, I. Lehtiniemi, M. Lundström, J. Aromaa

Conductivity is a typical physico-chemical property that has a substantial effect on electrical energy consumption in the electrorefining process. The objective of this study was to examine the validity of regression models predicting the conductivity of industrial copper electrorefining electrolytes. The models were based on data measured with synthetic solutions on a laboratory scale. The variables included in the models were temperature and the concentrations of copper, nickel, arsenic and sulfuric acid. Both first-order and combined effects of the variables were investigated. The measured data were analyzed using MODDE 8.0 modeling and design software. The validity of the models was investigated by comparing the predicted values with tankhouse conductivity measurements taken at the Boliden Harjavalta Copper Refinery in Pori in Finland. During the tankhouse tests, the conductivity and temperature of the industrial electrolyte were measured, and the composition of the electrolyte was analyzed. The measured conductivity values were compared with the predicted conductivities calculated using the developed models. The conductivity model developed in this paper was shown to be more accurate than previous models and suitable for industrial use.

By W. J. Whiten

"Models of cone crushers and vibrating screens are described. These models have been constructed from actual plant data using a systematic model-building technique. Included in this technique is regression analysis using multi-dimensional spline functions.The models have been used to simulate complete crushing plants and hence to design and evaluate a control system for crushing plants."

Jan 1, 2014