Search Documents

By S. Chatterjee

Mining represents the first industry in the United States to have federally mandated training for its workers. Although the topics to be covered are specified in 30 CFR 48, course content is left to the discretion of the individual mine operators. Unfortunately, certain topics to be covered, such as prevention of accidents, are usually mine specific, making it very difficult to use the same course content in every mine. Further, training requirements may change from one mine to another, due to changes in the demographic characteristics of the workers, or changes in job and organizational characteristics. Therefore, if the intention of safety training is to modify the behavior of workers, it is expected that there should be some changes in the content of safety training programs in order to address the specific requirements of individual mines, or at least mines of similar worker and job characteristics. This study has been directed towards the development of a systems-based procedure for conducting a needs analysis. A special effort was made to understand the psychology of worker behavior by analyzing worker reactions to various organizational and job characteristics.

Jan 1, 1994

By H. R. Taylor

The history and development of this property is more or less familiar to nearly everyone connected with the mining industry, so that only a brief outline of the more important facts will be given in this article. In 1916, a small pilot mill was constructed by the British Columbia Copper Company at Copper Mountain, and during 1916 and 1917 test work was conducted to determine the possibility of concentrating the ore and also to work out a suitable flow-sheet. In the spring of 1917, the location of a mill site at Allen by, which is about 8,% miles from Copper Mountain, and near the Similkameen river, was decided on, and the designing of a 2,000-ton plant was then worked out by Bradley, Bruff and Labarthe. Early in 1918, the actual construction of the concentrator began, and, after considerable labour difficulties, it was completed in 1920. During this period of construction, the West Kootenay Power Company ran a 60,000-volt power line over from Greenwood, a distance of 102 miles, and also built a sub-station at Allenby to take care of the mine and mill. The concentrator was started up on October 20th, 1920, and ran until December 11th, 1920, a total of 18,354 tons of ore being milled. The results of this short period of operation were encouraging, but, due to tlie prevailing low price of copper and high wages, it was necessary to shut down until a more favourable time. During the latter half of 1923, some work was done on remodelling the mill. This work continued until January 8th, 1924, when it was suspended.

Jan 1, 1929

By F D. I Hodgson

Twenty-seven observation test pits were excavated at four different spoils dumps at three collieries in the Witbank Coalfield. The holes were dug into the upper three metres of the spoils to ascertain if any weathering profiles, variation with age or influence of topsoil covering could be gauged. Samples from these holes were also subjected to laboratory testing (ABA, humidity cells and mineralogy on several selected samples). The test pits showed that there was a good correlation between in situ paste pH-values and ABA results for samples taken from the pits. At all the collieries, no correlation between age of spoils and in situ acidity could conclusively be drawn. The depth of soil cover also appears to be a minor consideration in determining the eventual acidity of the spoil. In the pits where acidity was found, the weathering was evident when contrasted to areas still buffered. It is unclear if the weathering leads to the acidity or vice versa, as the soil covering appeared to be similar. The spoils proved to be extremely variable with regard to particle size and material on a micro and macro scale. Evidence from most of the holes suggested that there was enough water contained in the fine material in the spoils to support the initiation of acid generation. Conclusions from this investigation are that the mineralogy of the spoils is the most important factor in determining the eventual occurrence of acidic hotspots, and that prior characterisation and selective handling will provide the best management practice for these spoils.

Jan 1, 2003

By Sidney Katell

An estimated capital investment of $76,499,800 will be required for a plant designed and built to produce 90 million standard cubic feet per day (std.c.f.d.) of synthetic pipeline gas through Lurgi gasification of bituminous char. This investment figure does not include the pretreatment plant, the cost of which is assumed to be reflected in the cost of the char fed to the gasification system. Shift conversion, C02 removal, and methanation are required after gasification in the Lurgi unit to make a gas suitable for pipeline transmission. Capital investment data are based upon equipment costs, January 1959. Based on a 90-percent or 330-day operating year, the operating cost before profit and Federal taxes with the char price as a variable will amount to the following: [ ]

Jan 1, 1959

By M Lellis

During the last decades, maintenance has changed from an ordinary repair activity to a complex function that plays an essential role contributing for the companyÆs results. The increasing level of complexity of modern equipment motivates maintenance personnel to improve both techniques, and management systems, in order to face the new challenges. Managing properly those modern means of production requires knowledge of methods and planning systems, controlling and performing maintenance tasks, in such a way that two objectives are achieved at the same time: system efficiency and cost-effectiveness. This paper shows CVRDÆs experience on evolving and implementing a model to plan and manage maintenance activities in order to achieve a higher level of performance on its operations.

Jan 1, 2003

By Dart Wantland

"AbstractThe scope of geophysics in civil engineering and the nature of exploration geophysics are briefly discussed. Engineering problems amenable to geophysical attack are illustrated by specific examples. The various methods available, accuracy of results, and costs are treated. The possibilities of new uses of geophysical techniques are pointed out.IntroductionTHE SCOPE of geophysics in engineering is different than in oil or mining exploration. In civil engineering, geophysics solves specific problems; as for example, what is the depth to bed-rock along the axis of a proposed dam? The area to be surveyed is of limited extent, and the subsurface information .sought is relatively near the surface. The engineering geophysicist is not called upon to investigate geological basins or extensive mineralized areas or to probe for data to thousands of feet in depth. The geophysical tools employed in the three fields are, however, quite similar; the differences are mainly in the objectives.The Natural Geophysical ExplorationThe terms geophysics and geophysical exploration have been used heretofore and will .be employed in what follows. The question is, therefore, What is geophysical exploration?Geophysical exploration is a line of field work where measurements are made at the ground surface with special instruments to get geological subsurface information. Briefly stated, geophysics is a form of exploration that supplements geological work. It is a blend of physics and geology since physical measurements are made •at the surface of the ground that can be interpreted in terms of subsurface conditions."

Jan 1, 1953

By Andreas Dietrich

Laser off-gas measurement of CO, O2 and temperature has been carried online in EAFs. A visualization screen shows the values of CO and Oxygen and temperature for the entire heat, and includes the status of furnace equipment. The historical data of the heats are stored such that the furnace performance can be evaluated and optimized. A short comparison between laser based and conventional systems has been carried out related to speed, influence of dust, water, pressure, protection for bag house explosions. A high water and/or dust content in the sample does not represent a problem for this type of system. The measurement method works without interruption even under worst conditions such as dirty scrap, carbon injection etc. The installation was developed in conjunction with Marienhuette, Graz. They are 100% scrap based with a tap to tap time of ca. 46 min. Keywords: Laser Measurement, Off Gas, CO, O2, Temperature

Jan 1, 2003

By R. N. Schulz

The recently completed modifications and additions to Reserve Mining Company's taconite concentrating process incorporate a totally new control system. Design of the new control scheme is centered on reliability, versatility, centralization, and optimization. The design objectives were achieved through a distributed control system based on a network of independent field located microprocessor based control system connected to a central control room. Operation of each micro-processors can be interrogated and modified from the central control room by the operator or by either of two computer systems. The two computer systems handle logging, alarming, specialized sequenced controls, and complex process optimization routines.

Jan 1, 1984

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Nicaragua has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Jul 1, 1930

By K. E. Stanfield

One of the initial projects under the oil-shale research and development phase of the Synthetic Liquid Fuels Act, Public- Law 290, 78th Congress, approved April 5, 1944, was a survey of oil shales of the United States for the selection of a site for an oil-shale demonstration plant. The oil shales were assayed by the conventional Bureau of Mines retort method proposed by Karrick and described by Guthrie in a more recent publication. From previous experience and that had in making these assays, it became evident that the assay method should be modified or replaced by a more satisfactory one. There are several outstanding objections to the Bureau of Mines oil-shale assay method: (1) the oil yields are frequently smaller than those obtained by other types of assay equipment and by commercial retorts; (2) the assayed oil yield represents only a portion of the organic matter in the shale, which under more favorable conditions, may, Jae converted, more completely into oil; (3) the retorting procedure is controlled mainly by trial-and-error methods; and (4) the assay requires approximately 6 hours for completion.

Jan 1, 1949

By E. M. De Souza

"A scientific testing program, sponsored by the Mining Industry Research Organization of Canada (MIROC), was undertaken on the surface and underground facilities of Inca's Crean Hill Mine to investigate the effectiveness of using dry drilling with a dust control system.The surface test work consisted of the monitoring of advance rates and bit life white a series of 165 mm holes, wet and dry, were drilled at both mine air (0.69MPa) and high pressure air (1.72MPa). The results, based on statistical evaluations of field data, indicated that penetration rates can be increased by an average of 24% when drilling dry with high air pressure and by approximately 27.5% when drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of reducing button wear by approximately 69% using high pressure air. The underground test work employed a dust collection system developed for use with large diameter holes (165 mm) and high pressure drilling. The testing program has indicated that an average increase in penetration rate of 35% can be achieved when dry drilling in rock (waste) and of 49% when dry drilling in ore with high air pressure. Although preliminary dust monitoring did not indicate any appreciable increase in dust concentration during dry drilling, further dust monitoring is still required.A comparative cost analysis has indicated the potential for reduction in drilling costs when dry drilling is utilized. Further testwork is to be conducted to develop a reliable dust collection system for underground production."

Jan 1, 1992

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By W. B. Hayes

The origin of the titanium pigment and metal? industries began with the discovery of the element titanium in 1791 by an Anglican clergyman named William Gregor. The titanium was discovered in magnetic black sands found in the beaches near Cornwall. England. The name titanium was established by the German chemist who discovered the mineral rutile in Hungary. Rutile is the oxide of the element titanium, which he called titan alluding to the mythological titans, giants of ancient Greece. The commercialization of titanium minerals began probably in 1916 with the production of titanium tetrachloride which was to be used in tracer bullets, flares and smoke screens during World War 1. In the 1920's composite pigments based on TiO2 barium sulfate and calcium sulfate were produced, followed by the introduction of the sulfate process anatase TiO2 crystal in the 1930s. The U.S. Bureau of Mines in 1938 began investigating titanium metal technology and promoted the development of the Kroll process. which is the magnesium metal reduction of titanium tetrachloride to produce titanium metal sponge.

Jan 1, 1989

By Zongliang Zuo, Mengqi Wei, Huaqing Xie, Qingbo Yu, Qin Qin

The resource utilization of copper slag is an attractive option of iron resource. Thermal energy recovery and direct reduction (TER-DR) system was proposed in this study. By theoretica lanalysis,the exergy efficiency of this system can reach to 57.3%. To investigate the feasibility of TER-DR system, copper slag composite pellets within lignite were prepared. As a new binder, pinesaw dust was added into the pellets. The diameter of pellets was 20 mm in experiments and the compressive strength of them was up to 831 N when the addition ratio of biomass was 29%. The results showed that the overall iron recovery reached to 90% and the separated iron concentrate was up to 93.5% when thetemperature is at 1423 K for 90 min with CaO addition ratio of 0.3. The process reduces the secondary environmental pollution of copper slag and will be applied well in the future.

Mar 1, 2018

By K. R. Vost

Calculations are given for the reduction in amplitude and change in phase of the diurnal variation in air temperature as the air flows through a mine. The concrete lining of a typical shaft was found to have a much greater effect than the steelwork. An increase in the conductivity of the concrete, or filling of the steelwork with water, did not have enough effect on the rise in air temperatures underground during the day to justify the costs involved. The steel temperature followed the air temperature much more closely than the concrete temperature did. Calculations are given for the heat stored in steel and concrete during the day.

Jan 1, 1980

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

By Husamuddin Ahmadzai

A survey of regulations and state of the art control technologies is presented relating to the smelting of primary aluminium, copper and recycling of residues. Some costs associated with the alternatives and trends for the coming decade in this. sector are identified.

Jan 1, 1992

By G. W. Birge

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Westmoreland County for coking tests was based, in part, on estimates of the coal reserves by Dowd,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in thousands of tons, as follows: [ ]

Jan 1, 1957

The paper reviews the results emanating from an experiment conducted in Bochum?Germany in which various international rope inspection authorities were requested to assess the conditions of a corroded rope sample as well as a rope sample containing internal fatigue breaks. Both samples were of the multi-layer low rotation construction.

Jan 1, 2000