Search Documents

By Mark R. Svinkin

This paper deals with application of the wave equation analysis to determine capacities of piles driven in saturated sandy soils. It shows that pile capacity in sandy soils changes with time after the completion of pile driving and depends on the ground water elevation. In saturated sandy soils the setup coefficient ranges between upper and lower curves represented by power functions. For a reliable prediction of pile capacity wave equation input should be adjusted with soil damping. Back calculation of soil damping from known pile capacity performed for five tested piles shows that skin damping coefficient changes with time in the same manner as the pile capacity and can be represented by the power functions for considered damping models.

Jan 1, 1995

By ERNEST A. HERSAY

ACCURATE ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fine¬ness of the pulverized product. Fine screens are expensive, easily injured by mis-use, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to he actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

May 1, 1906

By Paul. D. Merica

I LIKE to look upon the award this year also as a recognition of the importance of metallic materials of construction to the engineer and of the active progress which I believe is continually being made in almost all branches of that field today. It has been said that metals are the material backbone of industry and technology. Well in that case, I suppose we metallurgists are industry's bonesetters. And it is possibly not inappropriate that we should occasionally give some atten¬tion to those bony structures of our industrial activities upon which engineers in other fields hang their manifold and striking creations. What is going on in the field of metals development? Well, in the first

Jan 1, 1938

By J. F. McIlwain

The Bureau of Mines investigated fumes generated by selected welding materials used in mines in order to help determine their relative hazard potential. The initial phases of the study have been completed. A welding-fume generation and collection apparatus was designed, assembled, and calibrated. Five brands of coated, AWS-type E308-16 stainless steel electrodes were tested. Total fume generation rates of 0.39 to 0.51 g/min were measured. Quantitative chemical analyses were conducted for all of the principal firms constituents. Two analytical schemes were used to determine levels of the Cr6+ and Cr3+ species contained in the welding fumes; comparable results were obtained. The Cr6+ was found to be the most hazardous constituent, leading to a maximum allowable total fume exposure of 1 mg/m3. Fume generation rates and fume constituent analyses will be derived for other groups of welding electrodes using similar procedures.

Jan 1, 1983

By Jesse White, Tyler Salisbury

Research projects contain many stages of development from the conception of an idea to a fullscale commercial operation. The transition from laboratory-scale research to bench-scale roasting can represent a significant increase in complexity and cost, depending on how many variables are being evaluated. Thermogravimetric analysis (TGA) can simulate roasting conditions and produce a small sample for chemical analysis or materials characterization. A simultaneous thermogravimetric and differential scanning calorimetry (TG–DSC) can identify endothermic and exothermic reaction temperatures. Using thermal analysis, some of the process variables can be tested and eliminated such as ore and reagent blends, retention times, operating temperatures, and some atmospheres.

Jan 1, 2015

By Carlos Almeida, Bruno Matias, Stef Kapuskiak, Eduardo Silva, José Miguel Almeida, Alfredo Martins

Underwater intervention operations have been supported by robotic systems such as remotely operated vehicles (ROV) for a long time. In particular challenging scenarios such as the deep sea, the use of ROV systems for environment awareness is in fact the main tool of choice. With the technical advances in autonomous robotics, there is an increased effort in substitute ROVs whenever possible for autonomous underwater vehicles (AUV). These systems don't have tether and thus provide large advantages from the operations and logistic point of view. However the limited options for underwater communications render them impracticable for many tasks were real time environment awareness and direct human control is needed. Emerging applications in underwater mining, both at sea [1] and in inland flooded mines [2] pose additional requirements in terms of operation support needs and environment restrictions. Two main tasks are to be addressed by assisting robots in these underwater mining operations: providing adequate environment awareness for human operators and obtain precise realtime 3D environment modelling (particularly relevant for the mining planning). The use of ROVs with umbilical cable, has in this case large limitations due to the nature of the mining cutting (performed by dedicated systems) that limit manoeuvrability and pose high risk of cutting the cable or damaging the vehicle. In this paper we present EVA (Exploration VAMOS AUV) an innovative hybrid ROV/AUV system developed for operations support in inland underwater mining operations. This robot is always operated without tether, and the can be used in a wireless ROV tele-operation mode using very short range high bandwidth underwater communication systems and in autonomous AUV mode.

Jan 1, 2018

By Shigeru Ueda, Shin-ya Kitamura, Dong Jun Shin, Xu Gao

Steelmaking slag contains useful elements such as P and Mn. Generally, in the carbothermic reduction of slag, not only P but also Mn are reduced and a Fe–P–Mn alloy is formed. In this study, the possibility of the separation of Mn and P was investigated. A mixture of synthesized slag and graphite was heated at 1773 K, and the compositions of the separated slag and metal were analyzed. The results showed that with a decrease in basicity, the reduction of P was enhanced but that of Mn was suppressed. Thus, under an optimum condition, steelmaking slag was separated into a Fe–P alloy and a high MnO-containing slag. Although further investigation is necessary, the formed alloy and slag could be used as raw materials for fertilizers and Fe–Mn alloys, respectively. This paper elucidates the concept of this process and the results of the fundamental experiments.

Mar 1, 2018

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By R Winterberg

Concrete is a well established and reliable construction material for the permanent lining of tunnels, but shows some weak performance characteristics, which can be overcome by the addition of specialised fibre reinforcement. This paper addresses the particular performance design requirements of segmental linings, discussing the improvements of fi bres on concrete properties. Focus is made on the beneficial effects of fibre reinforcement on the cracking behaviour and the toughness performance, providing a safe and durable tunnel lining.Not only the mechanical performance of fibre reinforced concrete (FRC) for segmental linings, but also the durability of the linings has gained growing attention among the designers and consultants. Especially tunnel linings with exposure to media with corrosion potential, such as wastewater sewer tunnels or desalination plant outfall tunnels, have high requirements on their durability. The design of these structures must provide a comprehensive study of durability aspects. Fibre reinforcement can substantially improve the durability of concrete.Research has been carried out on the cracking behaviour of concrete. The beneficial effects of steel fibres on the cracking behaviour reduce the permeability by reducing the flow paths within the concrete. Crack bridging steel fibres create necking effects in bending cracks, leading to earlier closure of the cracks. Further, steel fibres create particular crack formations, which lead to a substantial reduction of the fl ow rates through separation cracks. The results also show that considerable cost savings can be achieved using FRC, as the thickness of the linings can be reduced.The durability design issues will be addressed and underlined by a case history on the Hobson Bay sewer tunnel in Auckland, New Zealand.

Mar 8, 2011

By Bjorge, Guy N.

MINING method improve through the gradual process of evolution and in 1340 there were no marked outstanding innovations. On the other hand refinements of detail and betterment: in equipment design continued to progress. Among the most important changes have been the increased application of trucks and highway equipment, including tractors and bull- dozers, to open-pit mining as exemplified by Phelps Dodge's Morenci operations; the Mesabi iron range; and the Tri-State district. Mass or bulk handling contributed its part underground with slurhers and conveyors at Consolidated Coppermines and slushers at Climax; and in open-pit mining. conveyors found increased use on the Mesabi range.

Jan 1, 1941

By Yaxiong An, Jianwen Yu, Yuexin Han, Peng Gao

This paper presents an industrial verification test, adding a high pressure grinding roll and magnetic separation operation after the third-stage fine crushing operation to reduce the particle size of ball mill feed and improve the processing capacity of grinding operation. The optimal process parameters of high pressure grinding roll and magnetic separation were determined to be a 10 mm of roller surface spacing, a 10.5 Mpa of roller surface pressure, a 14 r/min of roller surface speed, a particle feed size to the magnetic separator of P100 3 mm, and a 3000 Oe of magnetic field intensity. Under the above optimized conditions, the iron grade of magnetic pre-enriched concentrate increased significantly from 28.27% to 36.30%, and the iron recovery was 87.59%. Meanwhile, the yield of coarse tailings was 36.16%, which significantly reduced the amount of ore entering the subsequent ball mill-magnetic separation operation. The ball mill Bond work index Wib of raw materials and the pre-enriched concentrate were 11.76 kW•h/t and 10.46 kW•h/t, respectively. The relative grindability of the pre-enriched concentrate was increased by 34%.

May 31, 2024

By Edward Hanrahan

September 1981 I'm here today to report on a revolution -- a revolution in the way the Federal Government looks at energy. I'm not talking about a simple change in the relative emphasis on sources -- such as more recognition for coal and nuclear power, with less rhetoric about "soft- technology." Nor am I describing a mere change in focus -- from the demand side to the supply side. And I am not referring exclusively to our obvious goal of budget cuts. No, I'm here to discuss a fundamental change in Federal direction -- one that started as soon as President Reagan was inaugurated, and one that is articulated in the National Energy Policy Plan he sent to Congress in July. That brief policy document was backed up by three volumes of supporting data; but I think I can catch it's flavor for you in just three phrases: * First, various energy forms complete with each other and complement one another. * Second, fair competition among them (which includes honest pricing) will give us the best "energy mix." • And, finally there may be ligitimate arguments about where Federal responsibility in regard to energy spills over into Federal interference; but it's about time we drew the distinction -- and eliminated the latter. This Administration's national energy policy is quite different from any we have had in recent years. It is tuned to human nature and changing times. We are seeking the best practical solutions in the energy -a lot better than the ones we have been offered before, but still something less than perfection. One way we do that is by counting on a fully informed public to guide it's own destiny. And, instead of treating energy as an isolated entity, we recognize it as part of the overall economy. The President's Program for Economic Recovery is as much a factor in energy policy as the specific actions of the Department of Energy. One striking difference from the past energy policy 1s that this policy plan does not say: "In 1985 we will -produce so many hundreds of millions of tons of coal: . . . or . . . "By the end of this century the Nation will be deriving X percent of it's electricity from wind generators." Unfortunately, targets like these are what many people have come to expect from the Federal Government -- and what they think of as energy policy, whether the figures hold up in the long run or not. But . . . think about it! Nether the Department of Energy nor any other part of the Federal Government produces coal, or mines uranium, or manufactures solar collectors. There are only a few sections of the country where the Federal Government generates and sells electricity. So it does not take any great insight to recognize that the amount of energy we will produce or consume as a Nation In the future depends on many factors beyond direct government action. And those future totals cannot be predicted precisely, anyway -- by the Government or by anybody else. According to our way of thinking, the choices should be up to the people. When the free market works within a healthy economy, individuals express their preferences in the marketplace -- adjusting the balance of all energy factors continually in a way that no computer could be programmed to reflect perfectly. So, instead of having the Government issue a rigid set of numerical goals, our main concern simply is that there be enough energy. We want the Nation itself to decide how much that should be, what form it should take, and how that energy should reach consumers. The marketplace decides. Considering the recent past, this is indeed a revolutionary idea. It has some pitfalls, and we won't reach this ideal of free choice overnight. But that is where we are headed. And I'll offer some evidence in a few minutes that the policy has already started working. First, let me give you some of it's highlights: 1) Nobody who appreciates the philosophical underpinnings of this Administration will be surprised that the energy policy shows faith In domestic energy production and the supply side of the economy; but it also recognizes the important role of energy conservation -- the wise and efficient use of energy resources.

Jan 1, 1982

By C. B. Wu

This paper presents an analysis of comminution behavior of using cast iron segment (CIS) as fine grinding media with comparison to conventional steel ball. Grinding experiments utilize just one-size medium and mixed size media in laboratory were carried out and its efficiency is expected to be improved. The results show that no matter whether one-size medium or mixed size media employed, grinding efficiency of CIS media can be considerably equal to that of steel ball, on the other hand, grinding product by two kinds of media can conform to Robin-Rammler?s size characteristic curve and distribute in function of . )exp(100nbxy-= Comparing with steel ball, the milling capacity with CIS media could be increased up to about 8.6 percent, overcomminution decreased 3.96 in percentage and qualified size increased 3.98 in percentage in case of grinding fineness retained. At the same time, due to the improvement of grinding product size characteristic and its metal distribution characteristic, the grade and recovery of easy to separation size increased 0.24 in percentage and 6.47 in percentage respectively. Based on these results, the CIS media can be employed as novel fine medium for grinding process substituting for steel ball.

Jan 1, 2014

The promotion of good standards of reporting of the valuation of mineral assets in- public documents has been of concern to professional mining industry bodies, the securities industry, and. Government regulatory bodies for some time. This concern led to the National Companies and Securities Commission Release 149 (1990b) which laid down standards for Expert Reports on mining and petroleum securities, and other assets. The formation of the Australian Securities Commission provided an opportunity for a timely revision of Release 149 and the Mineral Valuation Committee was established by The Australasian Institute of Mining and Metallurgy in 1991 to review the existing code, and to develop an appropriate new Code and Guidelines.

Jan 1, 1994

By Erico Tabosa, Kym Runge, Peter Holtham

"The distribution of turbulence in an industrial scale mechanical flotation cell and its effect on flotation kinetics was studied using a fully instrumented 3m³ cell. The cell was operated at a copper concentrator in Australia with different combinations of airflow rates, impeller speeds and sizes and cell aspect ratio providing a wide range of hydrodynamic conditions. An analysis of the overall flotation cell performance showed that the overall copper recoveries were very similar for the conditions tested. However, by decoupling pulp effects from froth effects it was possible to evaluate whether the changes made affected the pulp zone and/or froth zone responses. The analysis showed that the overall recovery has the potential to be up to 7% higher, if not limited by froth recovery. The cell hydrodynamics were characterised by the overall energy dissipation rate and, to understand the distribution of turbulence within the cell, localised measurements were made using a piezoelectric vibration sensor. By comparing the metallurgical performance of the cell with the different hydrodynamic conditions it was found that the collection zone flotation rate constant was not directly related to overall energy dissipation, as is commonly observed at laboratory scale, where energy is usually only changed by varying impeller speed. In this study, energy dissipation rate was varied using not only impeller speed, but also the size of the impeller and the cell aspect ratio. In these circumstances, the best correlation was found to be between the collection zone flotation rate constant and the distribution of turbulence, i.e. the size of the turbulent zone."

Jan 1, 2014

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By Huanmei Yuan, Yuanyuan Wang, Hao Bai

Composite phase change materials are widely used in energy-saving and energy efficient process. Nano-encapsulated phase change materials are especially significant for making advanced working fluid applicable to waste heat recovery or storage. In this study, silica-coated stearic acid (SA) Nano composite phase change materials were prepared from tetraethyl orthosilicate (TEOS) and stearic acid (SA) via sol-gel process. The materials were investigated by Field emission scanning electron microscopy (FE-SEM), Transmission electron microscope (TEM), Fourier transform infrared spectroscopy(FT-IR) and Differential scanning calorimeter (DSC).The FE-SEM and TEM results show that monodisperse microspheres with stable core– shell structure were formed and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reaction between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity.

Jan 1, 2016

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By I. Gaballah

About forty percent of the SOx emissions are generated during the processing of metal sulfides of Cu, Pb, Zn, Ni, etc. Although new technologies for metal sulfide's smelting allow the production of H2S04 with a reasonable cost and decrease the emissions of sulfur oxides, the generated quantity of SOx is considered as a serious threat to environment. This paper suggests alternatives for low temperature processing of complex sulfide ores or concentrates 'CSO or CSC' under neutral, reducing and chlorinating atmospheres or their combination. At T > 400 "C, The neutral and reducing treatments allow the decomposition of pyrite and the partial recovery of sulfur as So and H2S. At 300 "C, the chlorinating treatment of CSC is fast, exothermic and allows the separation of FeC13 from the valuable elements' chlorides. It also generates SyCIx that can be either reduced by H2 or hydrolyzed in presence of sodium sulfide. The recovery rate of elemental sulfur with respect to the sulfur input exceeds 90 %.

Jan 1, 1999