Search Documents

By J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) slip along steeply dipping faults and (2) fracturing of strong strata above, or below, the coal seam. Both failure modes produce dynamic or ?shock? loads on the perimeter (roof, rib, floor) of mine openings. Special consideration should be given to these failure modes in planning of deep coal mines since their occurrence is not within the professional experience of many contemporary workers, and their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By Tony Walsh

Timely disclosure of information germane to the taking of investment decisions makes an essential contribution to ensuring the growth, efficiency and integrity of our capital markets. It is a core contributor to the maintenance of fair, orderly and transparent markets. The communication of relevant and comprehensible information to the investor plays a vital part in fostering investor confidence, thereby building depth and liquidity in our market. Australian Stock exchange Limited ("ASX") has had and continues to have a rewarding partnership with the mining industry to develop and recognise reporting standards, the JORC Code. This allows ready comparability and investor understanding of the mining investment vehicle. ASX's mining market has been successful because of the high reporting standards in the JORC Code and the high standards of professionalism and the intellectual capital that has been built up among the participants - the mining professionals, brokers, analysts, mining investors, professional advisers and the market operator. The balance of knowledge and understanding among these participants combined with the competition for capital, contributes to the standards for our mining market in a way that the market operator simply cannot replicate by market rules alone.

Jan 1, 2003

By M. J. Ferrante

High-temperature enthalpy and X-ray powder diffraction studies were con-ducted on aluminum sulfide (Al2S3) as part of the Bureau of Mines effort to provide new data for the advancement of mineral technology consistent with environmental preservation and energy conservation. Relative enthalpies were measured with a copper-block calorimeter from 298.15 to 879 K. Tabulated values are listed for heat capacity, entropy, Gibbs energy functions, and relative enthalpies between 298.15 and 900 K. Enthalpies were also given in the form of an equation and combined with published data to calculate standard enthalpies of formation and Gibbs energies of formation for reactions of crystalline aluminum with crystalline, liquid, and gaseous diatomic sulfur. The hexagonal, rhombohedral, and cubic phases of Al2S3 were identified by X-ray powder diffraction studies, and the indexed powder diffraction patterns of these phases are given. The hexagonal phase was stable to about 852 K and was partially converted to the rhombohedral form at 879 K.

Jan 1, 1981

By W. I. van Drunick

The Anglogold Ashanti (AGA) Navachab single stage SAG mill has provided an excellent setting for incremental optimization. Over the past decades, several interventions have resulted in marked improvements in specific performance; including steel ball scat removal, re-design of the mill lifters, replacement the pebble crusher and cyclone cluster, as well as the use of a vibrating screen in place of a discharge trommel. Recent initiatives now include an operating fine DMS circuit, studies on pre-crushing of the ROM feed and also fine-screening as an alternative to hydrocyclone classification. The current optimized state of the Navachab mill allows it to operate at approximately 20% higher efficiency when compared to mills of similar shell dimensions in gold mining, treating similar ore. This paper describes the systematic improvement of the SAG circuit to its current state.

Jan 1, 2012

By Mitchell, Edmund I.

VARIOUS suggestions as to proper fees for engineering services have been put forth by individual practitioners and by the American Institute of Consulting Engineers, the Connecticut Society of Civil Engineers, the Iowa Engineering Society and the Mahoning Valley (Ohio) Engineers, for the guidance of both the engineer and his client. The American Institute of Architects also has a schedule of minimum charges (revised 1908). So far as can be determined, however, the four national societies representing civil, mining, mechanical and electrical engineering have never given consideration to this question. An examination of technical periodicals published during the past decade shows that these schedules make provision for three methods of charging; i.e., (A) a percentage of the cost of the completed project; (B) a per diem rate; and (C) a fixed sum. Suggested minimum charges are as follows:

Jan 1, 1921

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By D. W. Scott

Thermodynamics is a powerful tool for investigating rotational isomerism in substituted ethanes and related molecules. Accurate calorimetric data can be interpreted to give information, not only about the energy difference between conformations, but also about the shape of the potential barrier hindering rotation from one conformation to another. However, a deterrent to this use of thermodynamics is the labor required to calculate the contributions to the thermodynamic functions for assumed potential functions. Tables of thermo-dynamic contributions for appropriate potential functions can eliminate that labor and greatly facilitate the thermodynamic study of rotational isomerism. In this research, tables of contributions to the thermodynamic functions were compiled for two potential functions typical of some commonly encountered examples of rotational isomerism. TYPES OF POTENTIAL FUNCTIONS Potential function 1, illustrated in figure 1, A, has two equal minima higher than the third. It has the general shape of the barrier to internal rotation in n-butane, for example. The trans conformation of n-butane has the lowest energy, and the two skew or gauche conformations have equal but higher energy. Potential function2, illustrated in figure 1, B, has two equal minima lower than the third. It has the general shape of the barrier in 2-methylbutane, for example. The two C1 conformations of 2-methylbutane have equal energy much lower than the assumed Cs conformation, which has not been observed spectroscopically.

Jan 1, 1962

By C. V. Millikan

New developments in air-gas lift practices in the Mid-Continent area since our Pall meeting in Fort Worth have done much to increase the efficiency of installations, and thus bring within economic limit of air-gas lift many wells which could not have been flowed profitably before. After the gas-lift had so thoroughly demonstrated its value in the Seminole field, its use spread to other areas and many installations were made of which the economy could be questioned. In the Seminole area, when production began to decline it was necessary either to increase the efficiency of the air or gas-lift or to put the wells on the pump, and pumping was not a process of lifting oil to which any operator looked forward with confidence. These conditions have resulted in the development of many practices which increase the efficiency and permit wells to be flowed with air or gas which earlier could not have been flowed economically, and wells which have been flowing to continue to a lower rate of production. The practices which have come into more common usage in the Mid-Continent area recently are mostly revivals of and improvements on practices which have been known in air-lift work for several years. Many arc peculiar to the individual well on which they are used. Intermittent Flowing Some interesting results are being obtained in Seminole and other districts by intermittent injection of gas. Gas is introduced during per-iods iods of 3 to 5 min. at a rate considerably over that necessary to acquire the production at a steady rate of injection, and is then cut off for a period of 3 to 15 min. Two to five wells are run from the same group of conlpressors. The total volume of gas required is sometimes reduced as much as one-third of that required when it is introduced at a constant rate, without changing the amount of oil production. The maximum pressure required is usually higher, but the average equal to or lower than that required for constant rate of flow. The effect on the wells is usually an irregular rate of flowing which may cause inconvenience where recycling is practiced. It would seem that this increase in efficiency is due to less slippage when the gas is introduced intermittently than when it is intro-

Jan 1, 1928

By Philip Thompson

Many new evaluation tools have been developed since the early 1990’s to aid the minerals processing test engineer. The areas of comminution, gravity concentration, flotation, and process mineralogy have received particular attention. This paper will describe new laboratory procedures in the areas of SAG mill testing, gravity concentration, and flotation testing. Computer assisted mineralogical examination equipment, new generations of mass balancing programs, and simulation programs will also be discussed.

Sep 12, 2005

By H. H. Murray

Abstract. World reserves of bauxite are abundant. Domestic reserves are limited and as a consequence the United States must rely on foreign suppliers for over 90 percent of its bauxite. Nationalization of many bauxite mining operations, levying of higher taxes, increased production and transportation costs, and attempts to create a uniform market price combined to place the United States in a vulnerable position. Alumina from kaolin, alunite, anorthosite, and oil shale have-been-or are being evaluated. World bauxite reserves are increasing and attempts to establish a uniform price have failed; therefore, it may be many years before domestic non-bauxite sources of alumina can compete with imported foreign bauxite.

Jan 1, 1980

By Harold Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand-book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By W. Lin

When a large area of open gob collapses suddenly, a windblast is produced that can cause considerable damage throughout the infrastructure of a mine. In a few cases, the windblast has been accompanied by ignitions of methane and/or coal dust. This paper describes the conduct and results of laboratory tests involving the compression of mixtures of air, methane and coal dust under a falling weight and while allowing controlled escape of the mixture. The transient responses on pressure and temperature sensors were recorded. In addition to an analysis of those records, the paper highlights those conditions in which ignitions occurred.

Jan 1, 1997

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007

By Y. J. Wang

A graphical technique by which the operating points for a two-fan ventilation system can be represented as the intersection of the modified fan curves is described. In constructing the diagram, the air quantities associated with the fans are considered to be independent variables and used as the axes of a rectangular coordinate system. The diagram may include, in addition to the modified fan curves, contour lines for resistances, pressures, and air powers. Procedures for drawing the diagram are discussed and illustrated with an example of the ventilation system.

Jan 1, 1986

By Hugo Leandro Rosa

A CBMM aplicou aços micro ligados ao nióbio em dois tipos de caçambas de carregadeiras de rodas que operam na usina de Araxá, Brasil. O objetivo foi avaliar os benefícios destes aços relacionados com redução dos custos, aumento da produtividade e vida útil dos componentes. Uma das máquinas analisadas coleta peças quentes de ferro nióbio para carregamento dos silos do britador. O uso de um aço ferramenta de alta resistência e resistente ao desgaste solucionou os problemas de deformação, desgaste e rachaduras durante o serviço, aumentando a vida útil da caçamba em cerca de 190%. A outra máquina avaliada foi uma carregadeira de rodas que opera na mina de minério de nióbio. O novo desenho com aços de alta resistência mecânica e resistente ao desgaste reduziu o peso em 14%, correspondendo ao incremento na capacidade de carga. A carga extra possibilitou um aumento na produtividade dos caminhões de 42 toneladas. Com os novos materiais, as trincas anteriormente encontradas na caçamba da pá carregadeira foram eliminadas, enquanto foi mantida a resistência ao desgaste antes oferecida pelo aço revestido com carbeto de cromo reduzindo também os custos de investimento em 7%.

Aug 17, 2017

By Kym Runge, Wei Huang, Fengnian Shi, Christian Antonio

"This paper presents an emerging High Voltage Pulse (HVP) technology for ore pre-treatment. Unlike previous studies where HVP was utilized as a crusher to pulverize ore particles to micron size ranges for downstream processing, the researchers at the Julius Kruttschnitt Mineral Research Centre (JKMRC) use HVP to enhance ore processability. Application of relatively low levels of HVP energy to selectively break mineralized particles from barren rocks, followed by size-based screening separation enables the feed ore to be split into high grade and low grade products. During HVP treatment, cracks/micro-cracks are generated which results in pre-weakening of the treated ore particles, which ultimately results in energy savings in the downstream comminution processes. HVP treatment followed by conventional grinding also results in improved liberation of the valuable minerals in comparison to that achieved with traditional conventional comminution, subsequently improving downstream separation efficiencies. The three major improvements in ore processability through HVP pre-treatment have the potential to facilitate rejection of low grade ore prior to processing, increase production rates, reduce the energy required for comminution and improve flotation separation recoveries. This paper summarizes the major research outcomes of HVP pre-treatment demonstrated using ores from various mining operations conducted by the JKMRC. It also discusses the barriers that must be overcome before it can be adopted by industry with confidence in a continuous high tonnage rate application.INTRODUCTIONThe challenges of declining ore grades and increased plant throughput rates, resulting in higher energy consumption and operational costs, require the mining industry to adopt new technologies to make future ore treatment economically viable. Over the past 50 years, many researchers have engaged in investigating novel comminution techniques. Since Yutkin (1955) first demonstrated the potential to generate shock waves with pressures exceeding 103 MPa via electrical breakdown of water, several applications of electrohydraulic crushing by shock waves have been reported (Curley-Macauly, 1968). Interest in this technique was bolstered when Andres (1977) demonstrated that electrodynamic fragmentation results in superior liberation of mineral grains as compared with conventional grinding techniques. Despite mounting laboratory-scale evidence of the efficacy of electrodynamic fragmentation for mineral liberation, development of the technology for full-scale operation has stalled, primarily because the energy required to achieve desirable mineral liberation is approximately two to three times that of mechanical comminution, amounting to approximately 100 kWh/t for typical mineral ores (Andres et al., 2002)."

Jan 1, 2018

By R. Casagrande, L. R. Moore, J. Sessoms, P. Macy

"A South American nickel mine has been producing a nickel concentrate that also contains copper and iron (15 percent nickel, 5 percent copper, 28 percent iron) for the end use of stainless steel production. A critical specification for the quality of the steel is the iron to magnesium oxide ratio (Fe:MgO), with a ratio of below 3.5:1 having a substantial impact on the nickel value. This nickel concentrate producer historically mined the sulfur-rich mineral pyroxenite but had been forced to move to a magnesium oxide/silicate (MgO/SiO4)-rich mineral harzburgite, resulting in nickel recovery being reduced to around 50 percent to maintain the required Fe:MgO ratio. In this study, ore mineralogy, water chemistry and the chemistries associated with the flotation process were evaluated in an effort to increase nickel recovery while maintaining the Fe:MgO ratio according to specification. New chemistry was introduced with the specific goal of complexing with the MgO and retarding its interaction with the bubble flow in the flotation process.IntroductionGlobal nickel production in 2011 totalled to 1,770,000 tons, according to the Raw Materials Group (2013). From 1950 to 2005 there was an aggregate 4.4 percent increase in nickel production, with a market-value high of $1,000/ton nickel reached in 1998 (Mudd, 2010). Approximately 65 percent of nickel production is consumed by the stainless steel industry, with 12 percent of the remainder used in super alloys or nonferrous alloys. Nickel imparts corrosion resistance, temperature resistance and other benefits to its alloys (Table 1) (Oberg, 1996; Cáceres, 2003). The dominant types of nickel-bearing ores are classified as either laterites (limonite: nickel-iron oxide; and garnierite: nickel hydrosilicate) or magmatic sulfide deposits (pentlandite: iron-nickel sulfide) (U.S. Geological Survey, 2013a, 2013b). In 2012, about 40 percent of the nickel ore mined was sulfidic-type ores and about 60 percent was laterite. The processing of laterite ore is expected to continue to increase as the availability of sulfidic ores continues to decline."

Jan 1, 2015

By R. Mathur

Cu isotope fractionation in low temperature aqueous environments has been well documented. Here we apply Cu isotopes to two distinct, yet related mining problems. First, an exploration geological application where we measured copper isotope fractionation in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in 4 porphyry copper deposits located in South western USA. Cu isotope patterns exist in the lateral and vertical distribution within the mines coupled with distinct relationships with Cu grade. Second, a hydrometallurgical application where we measured the leach fluids, feed and residues from a quick leach text of Cañariaco ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the power and ability of using the Cu isotope technique to understand low temperature aqueous processed involving copper.

Jan 1, 2010