Search Documents

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

By Ivan C. Machado

Jaguar Mining Inc. is implementing a 1.1 Mtpy, 7-year LOM gold project in the Iron Quadrangle (?Quadrilátero Ferrífero?), Brazil. Construction is on schedule and startup is programmed for Q2 2010. Mill feed grade averages 4.43 g/t and LOM gold production is estimated at 800,000 oz. The project entails two sulfide underground mines and three oxide/transition open pit mines. A state-of-the-art flotation/gravity concentration/CIP Plant has been designed based on testwork carried out by internationally recognized Canadian, U.S., and Brazilian laboratories. The mass recovery of the flotation section is only ca 10%, while its gold recovery is about 90%. Therefore, the CIP-ADR Plant will treat only 10% of the solids mass contained in the mill feed, while 90% will be fully cyanide-free material that will be partially used to feed a Backfill Plant. The leached tailings will be conveyed to a rather small tailings dam, whose 20- m3/h supernatant solution will be treated by a new electrolytic technology. The plant design contemplates a High Density Thickener for the cyanide-free rejects exceeding the backfill demand and a Regrinding Section before the Leaching Circuit. The estimated overall metallurgical recovery sits around 92%. This paper focus on the use of modern technologies to reduce costs, risks, and liabilities.

May 1, 2010

By M J. Kindley

The Golden Cross Gold Mine Project is now fully operational and into its second year of operation. Because of its location in the sensitive Coromandel Peninsula , strict water management and environmental requirements had to be met. This led to the development of new technologies for cyanide recovery and the adoption of advanced water management and water treatment systems. This paper discusses the water management and treatment system adopted for contaminated water at Golden Cross and provides data on the operational history to date.

Jan 1, 1993

By Jose Antonio Silva Souza, Emanuel Negrao Macedo, Iara Ferreira Santos, Otacilio Dias, Luis C. A. Venancio

"The Bayer process alumina production generates 0.7 to 2.0 ton of bauxite residue (BR) and an average of 1.0 ton of C02 per ton of alumina produced. The direct reaction of exhaust gases to reduce the alkalinity of the BR may allow a triple gain: improve the storage conditions, open a range of new applications for BR and sequester from 16 to 102 kg of C02 per ton of alumina. This paper shows the measurement of C02 captured during a pilot scale reaction of a suspension of BR in water with flue gas, produced from direct oil burning. Three different types of reactors were used: one spray tower and two packed columns. The inlet and exhaust gases were analyzed using electrochemical and non dispersive infrared sensors. The pH of the suspension was monitored during and after the reaction to evaluate the buffer effect.IntroductionAlumina is mainly produced from refining bauxite using the Bayer process. This process consists of extracting the aluminum oxide through its dissolution in caustic soda and the separation of insoluble residues. The remaining bauxite residue (BR) although not particularly toxic, poses risks to the environment due to the large volume and its reactivity. According to the latest technology it is stacked on sealed deposits specially constructed. To date the vast majority of the bauxite residue that has been produced was stored and were not incorporated into any existing production processes to significant amount with exception to some extent of the sintering process residue at Russia and China [l]. On the other hand, a strategic goal was set in 2010 by the Bauxite and Alumina Committee of the International Aluminium Institute (formed by the majority of the industries) to reuse 20% of BR in 2025 [2]. China has established the same objective for 2015[1].This paper is a sequel of two others presented at TMS 2010/2012 [3-4] and describes:• A pilot plant assembled for testing the carbonation process of BR with gaseous effluents similar of the refining process.• The methodology used to measure the amount of C02 captured during the carbonation process.• The results of the carbonation process, the C02 capture and the buffering effect of the pH.This process is studied in order to consume minimal power and use the effluent as efficiently as possible in different reactors from low cost to ultra high performance. The process is designed for minimizing the power consumption and equipment investment."

Jan 1, 2013

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation's petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By R. J. Gochin, P. Bevilacqua, G. D. Schena

This class of flowsheet-dependent simulators does not replace modular simulators, such as Modsim and Microsim, which are necessary for the assessment of different flowsheets before selection of the most desirable technical option and for investigation of the fine details of unit processes. The system presented here is regarded as complementary, serving in the early stages of feasibility studies as an aid to assessing the convenience and economics of preconcentration; the example used is of dense-medium preconcentration of a barytes-fluorite ore

Jun 13, 1905

Economic recovery of valuable natural resources is enhanced through an integrated approach to establishing and operating the mine.Gordonstone has a unique and valuable high quality coal and the basic aim for the mine is to satisfy customers through high standards of safety, productivity and reliability and genuine regard for its people.Gordonstone defined its main resources available for recovery of its natural resource and has designed and built facilities which display technical and engineering excellence.But to build a world class mine Gordonstone recognised the need to take a large- step beyond relying on technical excellence. In designing Gordonstone mine all aspects of coal mining were treated as part of an integrated process.This paper will explain the route Gordonstone has taken and will continue to take into the future in using an integrated approach to mining.

Jan 1, 1993

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By B. R. Stewart

The exclusion of coal fly ash from regulation as a hazardous waste has led to increased interest in returning ash to the coalfields for co-disposal. A multi-year column study used coal refuse with high potential acidity (4% total-S), and two alkaline ashes in various bulk-blends. The unamended refuse acidified rapidly, producing acidic (pH 1.7) leachates, high in dissolved metals. Treatments blended with sufficiently high amounts (20 to 33%) of alkaline ash produced alkaline (PH >8.4) leachates with low metal levels, while lower ash blending rates acidified over time to produce metalliferous leachates. Examination of solid materials indicated that pyrite oxidation was occurring to some extent in all treatments. A regression equation (r = 0.95) was developed to estimate time to net acid release for mixtures of these materials. Ash alkalinity and refuse potential acidity must be balanced to insure water quality for co-disposal environments, or the ash materials should be isolated away from acidic drainage waters.

Jan 1, 1997

By Thomas Pallua, William C. Gates

"Two major railroad companies have identified several segments along the railroad corridor betweenTehachapi and Bakersfield, Kern County in California that require construction of a second track to improve operations in this area. The total project proposes an upgrade of five segments along the Tehachapi-Bakersfield route. The authors focused on two segments: Walong to Marcel and Cliff Siding Extension. The second track project comprised design of a through-cut adjacent to an existing tunnel and up to 120-feet-high (36m) side-hill cuts (both in granitic rock). The authors characterized the geologic ground conditions and ground behavior, including rock mass quality and strength using a combination of rock core drilling and rock slope mapping. The rock mass is generally characterized as granitic tonalite with strong core stones surrounded by a matrix of decomposed granite (DG)."

Jan 1, 2017

In the late 1980s and into the 1990s, the Mountain Pass Mine in California produced about 40 percent of the world?s rare earth elements. At the height of this production, the facility produced up to 54 L/s (850 gpm) of saltwater that was piped to offshore holding ponds where the water was evaporated. In 1998, following a series of waste water pipeline breaches, separations activities were suspended, reducing the Mountain Pass site to just the openpit mine and mill. The environmental concerns were addressed and the affected areas have since been remediated. However, in the years following the breaches, 97 percent of the world?s production of rare earth elements moved to China. By 2011, Molycorp, and the Mountain Pass Mine, had rebounded from the difficult times and were once again in a position to become a significant player in the rare earth industry.

Jan 1, 2011

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Mark H. Hashiguchi

Examination of tensile bar surfaces shortly after destructive testing was conducted to search for clues that would aid in optimization of mechanical properties, especially tensile strength, yield strength and elongation to fracture. Cu-Ni-Si-Cr alloy bars in the as-cast, forged, rolled and extruded conditions were examined. Low ductility bars (<4% Elongation) showed dramatically different features than the fracture surfaces of high strength - high ductility bars (7 to 10% Elongation). Analysis of the fracture surfaces at 15X to 2000X and use of Energy-Dispersive X-Ray Spectroscopy (EDS) identified Ni-Si and Ni-Si-Cr precipitates of varying sizes and morphologies. Thermo-mechanical processing techniques to control the size and distribution of these precipitates show promise in improving the properties and performance of this alloy system and appear to correlate with improvements in the fracture surface morphology.

Jan 1, 2008

By L. C. IlsLey

The observations made by Bureau of Mines engineers of permissible equipment installed in about 40 mines have indicated a chance for improvement in designs calling for the use of bolts , screws , studs , etc. , especially with respect to bolt sizes and protection from mechanical injury .

May 1, 1931

By Mayumy Amparo Cabrera-Ramírez

Polymetallic nodules are a widespread resource in the Pacific Ocean, particularly in the areas of Clarion-Clipperton (Cronan, 2000). The most abundant mineral phases are forme d by iron and manganese oxides, with minor elements such as nickel, copper, cobalt, molybdenum and rare earths elements (Cronan, 1977; Cronan and Moorby, 1981; Iyer and Sharma, 1990; Mangini et al. 1990; Banerjee et al. 1991). In the Clarion-Clipperton Zone (CCZ), several authors mention that there are three main mineral species of manganese oxides, which have been recognized and which are associated with different processes of formation: todorokita (Mn2+, Ca, Mg) Mn3 4+ O7. H2), vernadite dMnO and birnessite enriched in Fe and (Na, Ca) 0.5 (Mn4+, Mn3+) 2O4. 1.5 H2O. In nodules of hydrothermal origin have been found todorokite, birnessite, vernadite, goethite and pyrolusite. Although there are many oxides and hydroxides of manganese and iron in amorphous and microcrystalline phases that make up the bulk of the nodule (Frondel et al. 1960; Cronan 1977; Dymond 1981; Calvert and Piper, 1984; Aplin and Cronan, 1985; Martin and Lallier, 1993; Achurra et al. 2009), identifying specific mineral phases is difficult due to the intergrowth of different phases and associated detrital material.

Sep 14, 2011

By R. E. Sinke

Demerara Bauxite Co. in British Guiana has come a long way in tackling the problem of stripping and removing overburden. When the company started mining in 1917, overburden was hand-loaded into carts pulled by donkeys. Since then it has been recognized that overburden removal is one of the greatest problems. Over the past years a great quantity of equipment has been purchased, discarded as it became obsolete, and replaced with better and cheaper tools. The policy has kept the company&apos;s overburden removal costs within reason. Accurate records of costs per cubic yard and cubic yards per hour per unit have been kept for many kinds of equipment. Walking draglines and hydraulicking equipment are the key approaches to the current operation, but shovels, tractor-drawn wagons, self-propelled rubber tired scrapers, and tractor-scrapers still have limited applications. Mackenzie, operational headquarters of the Demerara Bauxite Co. Ltd., is on the Demerara River, 65 miles from Georgetown, British Guiana. Ore treatment and ship loading facilities are at Mackenzie, head of navigation for ocean-going vessels and the mines are located 7 to 40 miles farther upstream.

Jan 4, 1955

By P. Hazebroek, M. Prats, E. E. Allen

Well locations in water floods frequently do not coincide with the ideal well locations associated with the flood pattern which is used. A question of importance is. "How much oil is lost because of this?". This is the problem treated in this paper. It is assumed that each pattern in a five-spot flood has the proper number of production and injection wells but that the wells may be off-pattern. The distance by which a well is off-patern is given in terms of the pattern spacing, defined as the length of one side of a five-spot. The influence of off-pattern wells on the performance of a five-spot flood has been investigated mathematically for unit mobility ratio. All production and injection rates are assumed to remain equal. The loss in recovery resulting from pattern irregularitie: has been calculated at a cumulative water injection corresponding to a 98 per cent water-cut in a regular five-spot. Displacing a single production or injection well by about one-third the pattern distance reduces the total field recovery by 4.4/N per cent of the recovery obtainable with regular spacing, where N is the number of five-spots in the flood (assumed large). When off-pattern wells are separated by at least one regular five-spot and are displaced by less than one-third the pattern distance, the total loss in recovery in a large-scale flood is, at most, 1 per cent of the recovery obtainable from that field with a regular five-spot pattern. However, much higher losses may occur if the off-pattern wells are not separated by a regular five-spot, if the rates are imbalanced, or if the mobility of the injected water is higher than that of the crude. Although the loss in oil recovery due to pattern irregularity often may be low, the off-pattern case will always require injection of more water to reach the same final water-cut. The volume of water injected per unit volume of oil displaced has been calculated for each five-spot adjacent to a five-spot containing a single 08-pattern well. The cumulative water injection at the time of 98 per cent water-cut may be increased by as much as 37 per cent when a production well is displaced one-third the pattern distance toward an injection well. The existence of differences between actual subsurface locations and the idealized well patterns used in secondary recovery operations is well recognized. However, the methods commonly used for predicting waterflood behavior ignore such differences, even when subsurface locations are known. The reason for this is simple. The idealized well patterns are highly symmetrical and, as such, the production history of the pattern (and even of the field) can be determined from that of a few production wells—usually from only one. Consideration of the many irregular well spacings found in a specific field would entail a large amount of work, and then the results would be applicable only to that specific field. In an attempt to provide an answer to the more general problem, this paper considers a water flood having an idealized well pattern, except for one well which is not at its regular location. When several off-pattern wells are present, their contributions are assumed to be additive unless the off-pattern wells are close to each other. Only four positions of the off-center well (at x, y. of Fig. 1) are considered in this paper. These are shown

By F. Calizaya

This paper explains and discusses a computer program developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain project, Nevada.

Jan 1, 1994