Search Documents

By W. E. Benton

Diatomite or diatomaceous earth is a siliceous sedimentary rock principally made up of the skeletal remains of the diatom, a microscopic, single-cell aquatic plant related to algae. The unique structure, chemical stability and physical properties are the major attributes of diatomite not met by other forms of silica. The production of diatomite was down in 1982 vs. 1981, reflecting the worldwide recession. The principal markets for diatomite products continue to be basically filtration and fillers. The outlook is for small but steady growth into the 1990s.

Jan 1, 1983

By R. Strandahl

As one of the largest private utilities globally, E.ON currently operates hard coal fired power stations in with a total installed capacity of some 20.000 MW: These thermal power plants consume domestic coals but are increasingly dependent on imported seaborne traded coal (in 2009 approx. 17 million t). Knowing that the company’s reputation and credibility depends in part on how E.ON lives up to the responsibilities along the entire energy value chain, E.ON takes a collaborative approach with the various suppliers. Hence, E.ON’s responsible policy also applies to the procurement of coal; the utility launched in 2009 a comprehensive Corporate Responsibility program with special focus on supply-chain audits. One of the first coal audits focussed on the Cerrejón coal mine in North Eastern Colombia. The authors will share the key learning’s and experience from the Colombian audit jointly conducted with an independent auditor and E.ON experts from the Corporate CR and E.ON Energy Trading.

Jan 1, 2011

By Oliver W. Keener

The operation described herein differs from the usual practice in the Tri-State district in two important respects: (1) the ore is loaded into cars which are tramped to the shaft and hoisted on self-dumping cages, and (2) about 30 per cent of the ore is loaded by power shovels. The four-month period covered by the cost data appended at the end of the paper immediately followed a period of about one year during which the mine was shut down, and the expense incident to the resumption of operations is reflected in the costs. The author acknowledges the assistance of C. F. Jackson, mining engineer, U. S. Bureau of Mines, in the preparation of this paper and the compilation of the data.

Jan 1, 1929

By S. H. Seyedein, Hamed Tavakkoli, Mohammad Reza Aboutalebi, S. N. Asharafizadeh

The liquid–liquid extraction behavior of lutetium from different acidic solutions was investigated using two extractants, D2EHPA and PC88A, in kerosene. Lutetium extraction reactions with D2EHPA and PC88A from HNO3 and H2SO4 solutions were chemically and thermodynamically analyzed. It was found that each Lu cation was complexed with six monomers of the organic extractant and released three protons. Simultaneously, the Lu cation was instituted in the P–O–H group of the extractants. Thermodynamic analysis of reactions between extractants and acidic solutions showed that the D2EHPA-HNO3 system is the most favorable for extracting lutetium. It is noted that the calculated equilibrium constant of the reaction in this system was approximately six times larger than that of the D2EHPA-H2SO4 system. However, the value of the equilibrium constant for the D2EHPA-HNO3 system was evaluated to be approximately 200 times greater than that of the PC88A-HNO3 system. Therefore, one can conclude that the extraction behavior of lutetium is more influenced by the extractant type than the solutionmedium. The synergistic effect of different mixtures of extractants on the solvent extraction of lutetium was also examined, and the highest synergistic factor was obtained for a binary mixture of PC88A:D2EHPA at the ratio of 4:1 for both aqueous solutions.

Mar 15, 2021

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By W. C. Brice

Minnesota's mineral resources are widespread and diverse (Figure 1). In addition to the nation's largest iron and manganese reserves, the state contains sizeable vanadium, copper, and nickel resources. Recently it has been determined that the proterozoic unconformities in Minnesota have a favorable potential for uranium deposits. Finally, major potential exists in Minnesota's archean greenstone belts for gold, silver, and copper-zinc massive sulfides. Many of the state's mineral resources have been found in environmentally sensitive areas. This is not surprising since the natural forces associated with the formation of mineral deposits are often the same processes that create unusual landforms. For example, much of the state's copper-nickel is found within and adjoining the Boundary Waters Canoe Area (BWCA) and Lake Superior. The history of mineral development on the Mesabi Iron Range has also created culturally sensitive areas. Early iron mining development required the workers to live close to their jobs, and mine wastes were dumped as near the mine as possible. Few, if any, foresaw the time when taconite would be economic to mine. Therefore, it is not unusual to find valuable taconite resources located under towns and waste dumps on the Mesabi Iron Range.

Jan 1, 1980

By Pamela Bogust, York R. Smith

Photovoltaic (PV) modules are becoming an ever increasingly larger part of our energy portfolio. As more and more PV modules are installed and come on-line, management of end-of-life (EOL) modules becomes an important issue. Currently, management of overburden EOL PV modules is not an issue, but is anticipated to be by 2030. Recovery and recycling of valuable metals in PV modules presents several environmental and economic advantages. In this brief review, we will describe processes for refurbishing and recycling of PV silicon. These processes involve some combination of mechanical, thermal, and chemical processing, all of which all have their oPV) modules have become wn respective challenges. Also, projections of PV module material streams are also highlighted.

Mar 1, 2018

By J Kuva, M Parian, B I. Pålsson

One of the main factors affecting the suitability of an ore for autogenous grinding is the ore’s competency, ie providing enough critical stones for the grinding process. Several experimental test routines exist and are used for assessing the viability of the ore for autogenous grinding. However, very little attention is given to the generation of fatigue in large stones experiencing repeated shocks in the mill. To investigate this, large pebbles sampled from an industrial autogenous grinding mill running hard and soft ores were categorised based on the grinding energy. From the pebbles, small drill core samples were prepared and went through a series of fatigue cycle tests. Both hard and soft ores showed similar average resistance to failure in compression tests, but the hard ore had a consistent resistance with lower variations. The cores were scanned by XCT before and in-between fatigue tests at the highest reachable resolution, 1.5 µm voxel size. The outcome showed that a higher number of micro-cracks were visible in the soft ore compared to the hard ore. The frequency of micro-crack development in the soft ore may be the reason for its lower specific grinding energy compared to the hard ore. It is obvious that for realistic conditions in an autogenous grinding mill, stones are pre-weakened by fatigue before they fracture. Therefore, shortcut methods focusing only on running tests on fresh and small samples may operate in unrealistic conditions by ignoring the fatigue phenomenon. This is even more important for ores that are on the borderline to be considered as competent for autogenous milling.

Aug 24, 2022

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By Alfonso Guzmán da Silva

El análisis del trabajo señala la importancia y aplicación del proceso Sink & Float en la aceleración de la industria minera metálica, la no-metálica y la del carbón del Perú. Dicho procedimiento que implica la separación de una mezcla de partículas de densidades distintas a través de la diferencia de las mismas, tiene como ejemplo más próximo de su ejecución, a la compañía minera Milpo S. A., así como la primera planta instalada para la pre-concentración de minerales en el Perú, la corporación minera Castrovirreyna, en Huancavelica.

Jun 20, 1954

By John C. Stam

During the past 20 years, the seismic refraction method has been used for depth to bedrock investigations. Its usefulness, however, has been recognized mainly in engineering applications, for instance in connection with the construction of power stations and in dam site investigations etc. Although some knowledge of the depth to bedrock can be of advantage in many other fields, the use of the conventional 12 or 24 channel seismic refraction equipment has been very limited, especially in ore prospecting and mining operations. The reasons for this are mainly the rather complicated operation of the instruments and the high costs. A conventional seismic equipment requires a crew of six men, a highly trained operator and an interpreter. Furthermore, the use of explosives can under certain conditions be undesirable (naighbourhood of houses, damage to agricultural areas etc.). Since 1957 a new one-channel seismograph, 'constructed by Geophysical Specialties Company, Minneapolis, Minnesota, has been in use and this instrument simplifies operations and reduces their costs considerably.

Jan 1, 1959

By Jon Y. Kaneshiro, Ed Walton, Stephen J. Navin, Robert M. Sergeant, Storer J. Boone

The Coronado Traffic Tunnel is a proposed two-lane, reversible, road tunnel, which will relieve severe peak hour congestion problems on surface streets. The tunnel will take traffic from the Coronado Bay Bridge to Naval Air Station North Island. The project will include 12.5 m (41 ft) inside diameter by 1,112 m (3,650 ft) of tunnel, 552 m(1,815 ft) of cut and cover box structure, and 400 m (1,315 ft) of open cut structure. The geology consists of predominately clean and silty sand, saturated sand, with some clay layers, requiring Earth Pressure Balance or Slurry Shield tunneling technology.

Jan 1, 2001

By J. D. Forrester

SINCE the introduction of the first percussion rock drill in about 1850, drilling equipment has undergone a progressive evolution so that a wide range of special classes of machines now are marketed by several manufacturers. Essentially all of the drilling machines presently employed for blasthole drilling are of the hammer-drill type. They are classified as hand-held hammers (jackhammers, sinkers, etc.), drifters (light or heavy), and stopers and are of many sizes; varying in weight and rotative and blowing power. Most makes of drill machines fundamentally are the same in principle of operation as they are designed to strike a blow on the end of a drill rod in the manner of early-day hand drilling. However, beyond this common characteristic, the similarity among different makes ceases. In choosing between similar machines of one make or another, it is important to remember that rock drill manufacturers have not attempted to standardize drill parts, the result being that a mine operator must approach, because of replacement parts, standardization by limiting the makes of machines used. The present-day selection of any particular drilling machine is dependent fundamentally on its inherent ability to make a hole, or series of holes, as speedily and as cheaply as is possible. Two categories of controlling elements become apparent in any analysis devoted to making the choice of a drill, namely: 1-Conditions under which the equipment is to be used, such as mining method practiced, type of labor available, character of rock material. 2-Physical characteristics or features of the given drilling machine. Regardless of the controls of class 1, above, the elements of this category are fixed by several factors. All of them are interrelated and, though some often are more important in one case than in another, an unfavorable variation of any-others being essentially equal-is sufficient to discredit the optimum applicability of the particular drill machine. The relative factors in the selection of a machine are as follows: First cost-This is not generally an important item on a comparative basis as the marketing of drill machines is highly competitive and most makes are priced closely.

Jan 1, 1952

By Loic Galisson

"Urban tunneling projects are usually extensively monitored. Most of the instruments used rely on benchmarks providing a sustainable datum throughout the life of the project. The monitoring program also is based on a predicted model of deformation induced by specific construction methods. Events can interfere with those assumptions and eventually alter the stability of these datum. In addition, the anticipated ground conditions and hence the theoretical deformation model often differ from reality. Satellite Radar Interferometry provides useful information to overcome the weakness of the hypothesis made before construction. It is also a powerful tool to ensure the continuity of the monitoring program throughout the life of the project, accurately describing the true effect of the project on the surrounding environment. This paper emphasizes the benefits and limitations of this technique for urban tunneling applications, illustrated by examples of major tunneling projects around the world. MONITORING URBAN TUNNEL PROJECTS Why Monitoring? Retrofitting existing tunnels or constructing new tunnels – including access and retrieval shafts, portals and cross passages – implies an alteration of the neighboring soil structure. Excavating, dewatering, grouting, loading tie backs, etc. artificially modifies the natural equilibrium of the pore-water pressure, of the water table level and of soil stability. In many cases, the effects are immediate: ground loss, deformation of utilities, settlements of buildings, and distortion of infrastructure are a few examples resulting from construction activity.Instrumentation and Monitoring Scope To control and mitigate the risks of damage associated with the above effects, tunnel projects usually include an instrumentation and monitoring program. Depending on the level of geotechnical, structural and environmental risk, the magnitude of this program varies. Projects with a low exposure to risk may restrain the program to conventional methods such as limited topographical surveys and intermittent manual readings of geotechnical instruments. On the other hand, iconic projects with high risk or with controversial history may implement complex and extensive instrumentation plans, involving highly technical solutions such as Automated Motorized Total Stations (AMTS – see opposite Picture 1), Multi-Point Borehole Extensometers (MPBX), In-Place Inclinometers (IPI) and a wide series of fully automated geotechnical, structural and environmental sensors. In this case, all the devices are usually connected to field data loggers collecting raw data around the clock at frequencies ranging from days to seconds, depending on the sensors."

Jan 1, 2016

By Iván Mendoza

La Responsabilidad Social Empresarial (RSE) es una política que adoptan las empresas de manera voluntaria -en tanto relaciona las empresas mineras que instalan las unidades operativas y las poblaciones del entorno. En ese sentido, el presente texto describe los lineamientos que comprende dicha política. Luego, se desarrollan las diferencias entre los ámbitos económicos, organizativos e institucionales en las zonas rurales del país. El aspecto organizativo se aborda enfatizando el papel de las comunidades campesinas, mientras que el institucional destaca los roles de las municipalidades. Finalmente, se revisan las relaciones entre las empresas y la población.

Jul 1, 2013

By Takeshi Yoshikawa, Kazuki Morita, Yuichi Kato

"A composite composed of carbon fiber and a Cu-Si alloy is a promising candidate for next generation brake disc materials used in high-speed trains. The composite can be prepared by vacuum infiltration of the Cu-Si alloy into the fibrous carbon matrix. The activity of Si in the alloy plays an important role in controlling the formation of SiC; this formation is attributed to the reaction between the Si in the alloy and the carbon fiber during the infiltration process. Because Fe has strong affinity with Si, the addition of Fe is expected to decrease the activity of Si in the alloy. In the present work, the variation in the activity of Si in the alloy with the addition of Fe has been investigated by equilibrating a Cu-Fe-Si alloy with solid SiO2 and graphite under controlled CO partial pressure. The first-order and second-order interaction parameter of Fe on Si in molten Cu was determined to be -16 and 160, respectively. The negative value of the first-order interaction parameter clarified the addition of Fe to the Cu-Si alloy is effective in decreasing the activity of Si in the alloy.IntroductionIron-based materials have been commonly used for brake discs in high-speed trains. It becomes critical for brake disc materials to withstand high thermal loads with an increase in the maximum speed of high-speed trains. The fabrication of high heat-resistant, light-weight brake disc materials is then crucial for their use in next-generation high-speed trains. Carbon fiber is known to be a light-weight, high-strength material, and is considered to be a promising matrix material for use in brake discs. The Cu-Si alloy exhibits high thermal conductivity. The composite in which the Cu-Si alloy is added to the carbon fiber matrix is expected to be a high performance material for brake discs. The composite can be prepared by the infiltration of the Cu-Si alloy into the carbon fiber matrix at a temperature higher than 1700 K."

Jan 1, 2012

By H. R. McCabe

"The study of a detailed series of structure and isopach maps of the Palaeozoic strata of southwestern Manitoba indicates that the principal Palaeozoic tectonic elements -the Williston Basin and Elk Point Basin -have been modified to a considerable extent by major tectonic features of the Precambrian basement. The principal basement feature is the break between the Churchill and Superior provinces, which coincides roughly with the Manitoba-Saskatchewan border. East-west-trending orogenic belts within the Superior crustal block may also be reflected to some extent in later Palaeozoic movements. In addition, the Superior crustal block, as a whole, appears to have had a slightly different response to the tectonic forces, giving rise to both basin subsidence and basin uplift. During periods of deposition, especially during Ordovician time, the Manitoba portion of the basin appears to have undergone a relatively higher rate of subsidence, whereas during periods of erosion relatively greater amounts of uplift and truncation have occurred. As a result, the depositional and erosional patterns for most of the Palaeozoic formations in southwestern Manitoba are somewhat anomalous relative to the regional basin framework.Some prominent Palaeozoic structures probably are the result of salt solution and differential compaction caused directly or indirectly by relatively minor tectonic movements related to Precambrian basement features. In particular, the prominent hinge line at the edge of the Devonian Prairie Evaporite salt basin may be due, in large part, to salt solution. Numerous other small structural lows, structural highs and isopach thicks, probably resulting from salt solution, occur along the salt edge and have been important in modifying and controlling Mississippian oil accumulation in the Daly-Virden producing area."

Jan 1, 1967

By T. M. Needham

Increasing ore hardness led to a gradual reduction of mill throughput rates. This, combined with declining head grades and low gold price, prompted a review of milling practice at Kidston. Plant trials and computer simulation of the grinding circuit indicated the potential to increase mill throughput by up to 451 by reducing SAG mill feed size. Secondary crushing and additional ball milling capacity were installed. Commissioning was carried out successfully in September/October 1992. Design, operation and problems of the expanded circuit are discussed, and recent operating results are presented.

Jan 1, 1994

Hamersley Iron Pty. Limited has maintained an interest in the screening of iron ore fines (nominally -6 mm). However, no dry screening process had successfully demonstrated acceptable separating efficiencies at high tonnage rates, low operating costs, and mechanical reliability when screening iron ore fines (containing up to 6% free moisture) at sizes of around 1 to 2 mm. A new type of vibrating inclined screen has recently been developed which is claimed to have a non-blinding screening surface. It was decided to test a pilot scale unit in an existing pilot plant located at Hamersley's facilities at Dampier, Western Australia. The appropriate operating parameters such as vibration speed and feed rate were determined using one fine ore type. Mats with different aperture sizes, and different feed moisture contents were also tested. Trials were then conducted on various fine ore types to indicate the effect of different size distributions on separating efficiencies. The effects of feed moisture content were determined with these ore types, and a blend of lump (nominally -30+6 mm) and fines was tested to compare the screen's performance with that of the bottom deck of the minesite product Screens.

Jan 1, 1991

By Shaun Booth

Automating Delay Reporting to Deliver Effective Maintenance Corporate Background: Technology Company: Matrikon Inc. Global software and service provider of Information Technology and Control Solutions that deliver Business Results. Case Study Facility: Bulga Coal Handling and Preparation Plant <CHPP> Australian site, part of Xstrata, an international Swiss natural resources group. Technology: ProcessMORe ? Missed Opportunity Reporting (Delay Reporting). Matrikon?s technology implemented at many facilities, to deliver effective maintenance Matrikon International Inc. Global software and service provider of Industrial Decision Support, maintenance and control solutions, with universal connectivity to existing systems and work processes. ? 1999 ? 100 employees ? 2003 ? 450 employees ? Our offices: 20 offices worldwide: ? Quebec, Toronto, Edmonton, Calgary, Ft.McMurray, Vancouver ? U.S. ? Australia (formerly Hunter Controls)

May 1, 2003