Search Documents

By J. H. East, E. R. Maize

Probably no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. SO far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. Adjustments of Diesel Engines foR Underground Use A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn I lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:1, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Dicsel Operates hi confined places should contain less than % pct of carbon dioxide and at least 20 pct of

Jan 1, 1949

By Spooner H. W

The paper describes the search for mineral deposits in an area of 4,500 sq. miles of south-west Tasmania. The area is one of difficult access and the problem of speedy movement and maintenance of field parties was solved by the use of helicopters. The programme has followed a systematic pattern of the aerial photography of the exploration area with the preparation of photQmosaics and topographical base sheets from these mosaics. Geological maps were initially prepared by photogeological interpretation and making use where possible of pre-existing information. The maps produced were later checked by ground traverses. Geophysical maps were obtained by the use of airborne magnetic, electromagnetic and radiometric methods. Geophysical and geological anomalies were checked on the ground by a campaign using ground geophysical equipment in the former case and geological and geochemical work in both instances. Audio Frequency Magnetic and Induced Polarization techniques were used in an area which was covered by several hundred feet of Tertiary sediments.The campaign has reached the stage of the drilling of specific targets.INTRODUCTIONThis paper describes the activities of Lyell-E.Z. Explorations (L.E.E.), an organization which was formed in 1956 by the Mt. Lyell Mining and Railway Co. Ltd. and the Electrolytic Zinc Co. of Australasia Ltd. to explore for mineral deposits in an area of approximately 4,500 sq. miles in southwest and southern Tasmania. To provide the necessary personnel and equipment for this project the exploration resources of both Companies were pooled and augmented and a headquarters was established in Queenstown. The work was directed by a Committee of four made up of officials from both Companies; a review of this structure has recently been presented by Hall (1959).

Jan 1, 1960

By David E. Hardt

"One of the critical variables to be controlled during arc welding is the size or geometry of the weld pool. The measurement of pool geometry has become an increasingly important problem with the advance of welding automation and control, and this paper addresses that problem. The basic concept of pool size estimation via measurement of pool dynamics is presented. The theory underlying this concept is discussed and is followed by a review of the current work in this area. It is concluded that pool dynamics can be characterized by natural frequencies of oscillation, for stationary welds, and that these can be measured by appropriate signal processing performed on the arc voltage. However, it appears that only full penetration welds show a strong correlation between weld size and natural frequency. Also, the extension of these results to the realistic case of moving welds has yet to be considered in detail. Nonetheless, this method of in-process measurement for real-time weld process control is still quite attractive where applicable since it can be accomplished simply by modifying the arc current schedule and by signal processing of the arc voltage.INTRODUCTUIONThe study of welding process control has been dominated by research into methods of in processing sensing of the weld pool geometry. While it has been shown feasible to measure the topside pool geometry using video methods [1,2], the penetration or backside bead width have remained elusive quantities. This is particularly true if a topside sensor location is required.The concept of using weld pool motion as a pool geometry sensing method was proposed by Hardt et al. [3] and later demonstrated by Hardt and Zacksenhouse [5] and Richardson and Renwick [6]. The concept is based on the fluid dynamics of a pool constrained by a solid container and by significant surface tension forces (i.e. a small shallow pool, not a ""pond"" or ""lake""). Such a pool, if subjected to external forces, will exhibit a surface motion is a function of that force, the properties of the fluid, the surface tension, and the shape of the container. Thus, if this motion can be excited and measured, and the relationship to the pool geometry determined, a means of sensing pool shape will exist."

Jan 1, 1986

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX!EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 2000

By Jr. Taylor

The following heats of solution have been measured in 1.160 molal H2SO4 at 25° C: AH298, kcal./mole Be(c) + 77.44(H2SO4?47.849 H2O) H2(g) + BeSO4 (soln) -92.83 ± 0.11 BeSO4 ?(c) + 77.44 (H2SO4?47.849 H2O) BeSO4(soln) -16.45 ± 0.02 BeSO4?2H2O(c) + 77.44(H2SO4?47.849 H2O) BeSO4?2H2O(soln) -5.395 ± 0.019 BeSO4?4H2O(c) + 77.44 (H2SO4?47.849 H2O) BeSO4?4H2O(soln) 1.513 ± 0.010 Combining these data with other experimental results and data taken from National Bureau of Standards information yielded the following heats of formation at 298° K:

Jan 1, 1966

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By Arthur Wilson, Frederick Carr

INTRODUCTION 1. The application of retreat longwall mining to the North American coal mining conditions is becoming more advantageous as more experience is gained. The productivity results being achieved and potential possible illustrates that this system can be keystone of future underground coal production. 2. In the American coal fields multi-entry is normally practiced as this allows profitable longwall development with existing equipment and systems. Difficulties are being experienced however in the longwall retreat phase by the collapse of multi-entry roadways and excessive use of supplemental support in the following panel tailgates. In some instances the headgate of an operating face can also be in difficulty. 3. Jim Walter Resources Mining Division is developed on a mining plan that calls for three retreat longwalls at each of its four deep mines which have varying depths of cover and immediate roof and floor conditions. The 63 Mine has experienced longwall entry difficulty and there were differing viewpoints with respect to the best development systems to adopt particularily regarding the number of entries and pillar sizes. In an attempt to reconcile these different points of view J.W.R. asked Dr. Wilson to examine the problem and this paper outlines the new approach developed.

Jan 1, 1983

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By Waldbillig. D.

A baseline of the poisoning effect of hydrogen sulfide (H2S) fuel impurities on solid oxide fuel cell (SOFC) anodes was developed using polarization testing. After the baseline behaviour was characterized, tests to study the effect of various H2S concentrations on the rate and amount of cell voltage degradation and recovery were performed. Attempts were made to improve the rate and amount of recovery by various methods. Testing was very reproducible, but significant electrochemical performance degradation was seen after all H2S poisoning tests even at an H2S concentration of 0.1 ppm. Degradation is initially quite rapid, but after a period of time the rate of degradation levels off. After poisoning was complete, the H2S flow was stopped and the cells were allowed to recover. Some recovery was seen after poisoning, but cell performance was never fully recovered.

Jan 1, 2005

By Peter R. Whiteley

"This paper discusses gaseous, solid and liquid injection technologies employed in the aluminium industry. The reasons for injection systems are presented, together with a description of the processes used. This includes a review of injection in crucibles, furnaces, launders, and into special purpose metal treatment boxes. The paper covers both the primary and secondary aluminium industries. IntroductionMany injection technologies are used in the aluminium industry and are in a rapid state of development. This paper provides a review of these systems and presents some thoughts on the possible future application of injection to further improve productivity and reduce losses associated with current applications.The Needs for InjectionThere are many issues facing the process metallurgist in the aluminium industry which call for the application of injection technologies now and in the future. In order to categorise these issues the industry may be broken into primary and secondary aluminium, although some of the concerns occur in both areas.The forementioned issues are variously concerned with improving metal quality, improving productivity, and reducing process problems.The use of injection techniques will be discussed under the heading of solid, gaseous and liquid injections, and the objectives and benefits of each covered briefly."

Jan 1, 1996

By H. Kazemi

An ideal theoretical model of a naturally fractured reservoir with a uniform fracture distribution, motivated by an earlier model by Warren and Root, has been developed. This model consists of a finite circular reservoir with a centrally located well and two distinct porous regions, referred to as matrix and fracture, respectively. The matrix has high storage, but low flow capacity; the fracture has low storage, but high flow capacity. The flow in the entire reservoir is unsteady state. The results of this study are compared with the results of the earlier models, and it has been concluded that major conclusions of Warren and Root are quite substantial. Furthermore, an attempt has been made to study critically other analytical methods reported in the literature. In general, it may be concluded that the analysis of a naturally fractured reservoir from pressure transient data relies considerably on the degree and the type of heterogeneity of the system; the testing procedure and test facilities are sometimes as important. Nevertheless, under favorable conditions, one should be able to calculate in-situ characteristics of the matrix-fracture system, such as pore-volume ratio, over-all capacity of the formation, total storage capacity of the porous matrix, and some measure of matrix permeability. INTRODUCTION The analysis of flow and buildup tests for obtaining in-situ characteristics of oil and gas reservoirs has received considerable attention in the past decade. Most of the available techniques result in reliable conclusions in macroscopically homogeneous reservoirs or in the homogeneous reservoirs with only certain types of induced and/or inherent heterogeneity (such as wellbore damage, etc.). In general, the greater the degree of heterogeneity, the less the reliability of the information deduced from the pressure transient data. A commonly encountered heterogeneous system is a naturally fractured reservoir where two types of distinct porosities occur in the same formation. The region containing finer pores may have high storage and low flow capacities. This is called the matrix. The remaining region may have high flow capacity with low storage. The latter region is generally the set of interconnecting fractures and fissures of the rock, and for this reason it is called the fracture. Ordinarily, we wish to obtain the permeability and porosity of each region and perhaps the frequency of the fracture distribution in a reservoir. Such information is necessary for reservoir engineering. Other information, such as wellbore damage, will be useful in evaluating possible remedial work for such fields. Few authors have suggested theories to aid in calculating the in-situ characteristics of a naturally fractured reservoir similar to what we have described above. Pollardl suggested that a naturally fractured reservoir contained three distinct regions: a damaged or an improved region surrounding the wellbore, and the two remaining regions the same as described earlier. He suggested that the flow was taking place from the tight matrix into the highly conductive fractures, then into the we wllbore region and finally into the well column. He concluded that the average pressure buildup in each of these distinct regions can be expressed approximately in terms of an exponential decay function of time. He also hypothesized that the decay coefficients for each of these functions were significantly different from each other; consequently, each of these functions became dominant in turn, in the process of pressure buildup. Thus, by a proper graphic plot of the logarithm of wellbore pressure differences vs buildup time, each of these functions could be determined (see Fig. 1). Pollard suggested methods of determining the wellbore damage and fracture volume. Later Pirson and Pirson2 extended

Jan 1, 1970

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By R. Wang, N. J. Grant, B. C. Giessen

By crystallographic and X-ray methods, the existence and isonzorphism of Ti3Rh5 and Hf3Rhs were confirmed. Both phases are of the orthorhombic Ge3Rh5 type; lattice parameters and refined positional parameters are given. The structure is related both to the filled-up NiAs-B8 and Cu-AI types. An analogous phase with zirconium does not exist; the effect of ternary substitutions for titanium ad hafnium suggests a size factor limit to be active. A recent survey of phase diagrams of the T4 metals titanium, zirconium, and hafnium with the T, noble metals rhodium and iridium indicated the existence of the A3B5 phases Ti3Rhs, ZrsRhs, and HfsRhs. Ti3Rhs and Hf3Rh5 were found to be isostructural, based on the line-rich powder patterns which had not been analyzed. Zr3Rh5 was considered to have a substructure of the NbRu type (orthorhombically distorted B2-CsCl type).&apos; Because, in combinations with other transition metals, hafnium and zirconium are generally more likely to form isostructural phases than hafnium and titanium (with the significant exception of the Ti2Ni-"E93" type phases based on T4 metals2), the reversal of this relation for the A3B5 phases was of interest. As shown in the following, the nonexistence of Zr3Rhs has been established, the structures of Ti3Rh5 and Hf3Rh5 have been worked out, and crystal chemical relationships and stability criteria are reported. EXPERIMENTAL METHODS AND RESULTS Alloy Preparation and Phase Diagram Work. Alloys were prepared from high-purity (99.99+ pct) elements by arc-meltin3,4.Heat-treated alloys were annealed in a vacuum of 3 x X torr for 24 hr at 1300DC. Metal-lographic samples were etched electrolytically in concentrated HCl with 5 v ac for 5 min.3 X-ray diffraction powder patterns were taken on a GE XRD-5 dif-fractometer with Cum radiation at low scanning rates (0.2 deg per min for 28). It was confirmed that Ti3Rhs and Hf3Rh5 have similar diffraction patterns, and that an alloy with the composition Zr3Rhs has a different pattern. Six Zr-Fh alloys with 59 to 69 at. pct Rh were therefore prepared and investigated in the as-cast state by X-ray diffraction and metallography. Alloys at 59 and 61 at. pct Rh were found to be a single phase, with the distorted B2-CsC1 type structure typical for the off-stoichio- metric region of the phase (Zr,-,Rh,)Rh. This phase forms a eutectic with ZrRhs at about 66 at. pct Rh: accordingly, alloys between 61 and 69 pct at. pct Rh consisted of two phases. There is no evidence for the existence of Zr3Rh5. Based on the results in Rafs. 1 and 5, on the present work on Zr-Rh, and on several additional alloys investigated, the portions between the AB and AB3 stoi-chiometry for Ti-Rh, Zr-Rh, and Hf-Rh are as follows: Further, several ternary alloys near Ti3Rhs and Hf,Rhs were prepared in which it was attempted to replace titanium and hafnium partly by zirconium, niobium, tantalum, and germanium. The results will be discussed in a later section. Structure Determination of Ti3Rh5. Since Ti3Rh5 and Hf3Rh5 are isostructural, the following discussion will largely deal with the former. Although the powder pattern of TisRhs is complex, as found previously,1 it could be indexed by comparison with other structures of A3Bs stoichiometry. Ti3Rh5 was found to be isostructural with Ge3Rh5, whose orthorhombic structure had been elucidated by Geller.9 As both the sizes and atomic numbers of germanium and titanium are comparable, the unit cell volume and the peak intensities could be expected to be similar; however, significant differences exist in the atomic positions, as will be shown. All lines in the powder patterns of Ti3Rh5 and Hf3Rhj could be indexed with primitive orthorhombic unit cells with the lattice constants: The fractional errors are 10 The low-angle portion of the indexed powder pattern of Ti3Rh with sin2 8 < 0.30 is listed in Table I. The extinction laws Okl only with k = 2n and hOl only with h - 2n are compatible with the space group Pbo2 and the more symmetrical space group Phnm of Ge3Rh5. Finally, the positional parameters of Ti3Rh5 and HfsRhs were refined under the assumption that titanium and hafnium occupy the germanium positions in Ge3Rh5. Integrated intensities were obtained from the diffraction patterns by planimetry. Intensities of overlapping reflections were separated by an iteration process incorporated into the least-squares positional refinement program according to a method described previously. The intensities of Ge3Rh5 were used in the first separation cycle, while the atomic parameters of Ge3Rh5 were used as starting values in the first refinement cycle. Absorption due to specimen

Jan 1, 1970

By H. M. Chance

(Butte Meeting, August, 1913.) ADEQUATE treatment of the difficulties surrounding the valuation of mineral lands requires that agreement be first reached defining value as understood for the purpose of appraisal. To define value as the price of a product is not sufficient, and does not assist us in using the factors that cause variations in values and in relative values. The real value of any product depends primarily upon its relation to the necessities, comforts and pleasures of mankind. As the necessities, comforts and pleasures of the civilized races differ-from those of more primitive man, the value of products varies with the degree of civilization and the environment of the consumer. Coal has no value to the savages of warm climates, and arrow-head flint none to the residents of New York. It has long been recognized that what has. been termed ?intrinsic value " must be limited to materials that are essential to existence-air, water, food. But " intrinsic value " cannot be measured in monetary terms. The intrinsic value of a bushel of wheat is due to the fact that it will support the life of an individual for a certain definite time, but this fact does not enable us to measure or to express that value in monetary terms. It has often been proposed to adopt as a measure of the value of any product the quantity of labor necessary to produce it, but this method is of limited application, and will not apply to what may be termed " intrinsic values." For many reasons it might be well, while assenting to the fact that any material may be intrinsically valuable, to abandon the use of the term "intrinsic value." One of these reasons is the tendency to confuse the idea of " intrinsic value with a value that is conferred by economic conditions, that is purely artificial and that may be permanent or evanescent. Intrinsic value must from its nature be permanent and unchangeable.

Jan 7, 1913

By Riley S

Many regulatory bodies have, or are considering, guidelines that require rehabilitated mine spoils to be erosionally stable (satisfying quantitative limits) over specified design lifetimes. One of the problems facing the industry is that many of the computer models used for erosion assessment were developed for agricultural applications and are unable to predict the change in the shape of engineered landforms over extended periods of time. In particular, they cannot predict where valleys and gullies will develop in the landforms and how big or deep they will be. Furthermore, many existing models require considerable skill to use. A computer model (SIBERIA) developed by the first author, able to model this valley and gully development over long design lifetimes, and which is directly based on digital terrain maps is discussed here. Proposed rehabilitation strategies for waste rock dumps at Ranger Uranium Mine as assessed with SIBERIA are discussed. New features of SIBERIA of interest to the mining industry include the spatial distribution of erosion, deposition and gully development, and various measures of the quantitative risk of failure. A collaborative project with the Queensland Coal Association, involving the first author, aims to deliver these capabilities to the coal industry in a user-friendly package. The objective is the cost-effective rehabilitation of strip mines. Some preliminary results from this project are presented.

Jan 1, 1994

By S. E. Khalafalla

In support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has investigated a novel hydrometallurgical system with sulfur dioxide. Differential leaching with dissolved SO2 of manganese, nickel, and cobalt from their hydrous oxides was found to be very rapid and efficient--almost instantaneous and quantitative. In this method a given weight of mixed oxides previously ground to minus 200-mesh is slurried with a leach solution containing a specified quantity of dissolved SO2 for 10 minutes at room temperature and ambient pressure. An empirical leaching parameter, R, is defined as the ratio of the number of SO2 moles in the leaching solution to the weight of the metal oxide charge. Plots of the variation of metal extraction with the ratio R generate a series of sigmoidal-shaped curves, each of which is characteristic of a specific metal extraction. A threshold value of R is required to initiate the leaching of a given metal from the mixed oxides. Once this threshold is reached, the metal recovery can increase to more than 95 pct in very short times. For increasing values of R, the extractability of various metals by SO2 follows the order: Mn > Ni > Co >> Fe, Al, Cu. Differences in the threshold R values permit a variety of metal separations to be made simply by adjusting the quantity of SO2 in the contacting solution. Success in this leaching system depends upon comminuting the sea nodules to less than 0.149 mm (100-mesh). Above this critical size, leaching is slowed due to the inaccessibility of inner particle reacting groups to the SO2 leaching agent. This results in nonselective extraction and less extraction of preferred metal values. At or below 0.149 mm, leaching by SO, is possible with all its attributes of selectivity, sensitivity, and rapidity. Leaching with HC1 solutions of the same pH level as dissolved SO2 yielded mixed, slow, and incomplete metal extractions. This observation rules out any interpretation based on hydrogen ion as the leaching agent. The leaching curves resemble the complexometric titration curves of heavy metals with specific coordination species.

Jan 1, 1981

By Kathryn C. Sole

A novel solvent-extraction process for the refining of gold was recently commercialised, with the commissioning in May 1997 of a 24 t a-&apos; refinery at Harmony Gold Mine in Virginia, South Africa. The MinataurTM Process (Mintek Alternative Technology for Au Refining) uses solvent-extraction technology to produce gold of 99.99% purity from the cathode sludge arising from a conventional carbon-in-pulp / electrowinning circuit. Implementation of this process introduces significant cost benefits compared with the conventional dore smelting / toll-refining route previously followed. This paper outlines the process, presents selected operating results obtained during the first few months of operation, and provides some details of the associated techno-economic advantages.

Jan 1, 1998

By José J. Suárez

As pressure grows for commodity pricing, new mines are more difficult to develop, the stock markets demand better financial returns from mining companies, resources for the developing and operations are scarce, and developing countries in Asia, and Africa demand more metals, it is important that mining companies effect better utilization of capital to develop capital projects. In the last few years, the costs for Capital projects have been impacted by the following factors:

May 1, 2013