Search Documents

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By Joseph D. Davis

The term "fusain" was first adopted from the French by the American geologist J. J. Stevenson in 1911, according to Wheeler, (1),3 who applies it to that portion of coal resembling charcoal, which he treats as one of the four ingredients of banded bituminous coal. The term has since been adopted by American writers. The Germans use it with slightly different spelling - namely, fusit. It is the equivalent of "mother-of-coal" and "mineral charcoal" of the earlier British writers. The English word fusain is also applied to "a crayon of fine charcoal" and is derived from the Latin root fusus. OCCURRENCE OF FUSAIN IN COAL AND ITS RECOGNITION Fusain is fairly widely distributed in coals of all ranks in varying amounts. It is almost always present in very thin sheets between the bedding planes of the banded coal constituents and presents a jet-black silky appearance who n the coal is split away. As fusain has little cohesive power the coal splits readily along the planes where it occurs. Such fusain bands often attain appreciable thickness -- frequently 1/4 to 3/4 inch. -Beet (2) has reported a maximum thickness of 2 inches for fusain partings, and Sinnatt (3) has found it in the form of plates and lumps; one lump taken by him from the Peacock mine weighed 3-3/4 pounds. Bore (4) has found it in coal balls. Sinnatt (3) states that fusain occurs in two forms, "the first a hard compact variety occurring rather rarely, which can not be pulverized by pressure of the fingers the second type is the common substance" -- that is, a very friable, easily pulverized material. The writer has also found the two types of fusain in the same coal bed and has observed that the hard variety contained considerable calcium carbonate, which probably entered the material in situ by infiltration. Sinnatt further remarks that the layers of fusain (soft type) usually contain less moisture than the coal (or lose it more readily on exposure), and when exposed they quickly change to flocculent powder so that the fines of the coal as mined are likely to contain a major proportion of this substance.

Jan 1, 1929

By W. K. Loftus, H. S. Simpson

Discussion I. R. M. Cheston (Visitor): I should like to congratulate the authors on this interesting paper which graphically illustrates the overall effects of the gradual developments in diamond concentrating processes which have taken place over the past few years. These final stages of diamond concentration represent only a minor factor in the cost of diamond production but because of the shortage of highly trained people for this work, any easing of the burden on the sorting staff has an importance far beyond the immediate economic sphere. The search for the solution of problems posed by the economic and social conditions of industry is never-ending. The Diamond Research Laboratory is, even now, carrying out further work to improve still more the operation of general diamond recovery processes as described in the paper. Before looking at some of the latest developments in this field of final recovery, there are a few points arising from the paper on which I would like to comment. On page 321, reference is made to the X-ray sorters originally developed by the DRL. The paper gives a figure of 100 per cent recovery of diamonds from +7 mesh concentrates in two passes through the prototype machine. Not wishing to claim miraculous powers for our group, I would prefer to see this given as virtually 100 per cent recovery of all fluorescing diamonds. Firstly however much care is taken, there is bound to be an occasional operating loss. In the test work, 100 per cent recovery was made on many occasions but this was not always so. Secondly, although most diamonds fluoresce strongly under X-rays, some diamonds only fluoresce weakly. Type IIB diamonds, in fact hardly fluoresce at all, but the incidence of this special type of diamond is very low in most deposits. However, in operating the commercial X-ray machines, there is a certain background level of reflected radiation from other feed particles. Unless the diamond fluorescence is several times greater than this, it is not possible to achieve sufficient sensitivity in ejection. A certain small but variable proportion of diamonds from each deposit is always found to fluoresce too weakly to be recovered by the X-ray machine. Tests have shown, that for the De Beers mines, this proportion is considerably less than I per cent. These diamonds are nearly all dark brown or black in colour and therefore of low value. The degree of fluorescence does not, however, depend entirely on the colour or quality of the diamond and some of the brightest fluorescence comes from the lowest quality of boart diamonds. Investigations into the property of the diamond which causes this low fluorescence are being carried out. On page 322 it is suggested that zircon fluoresces in the same colour spectrum as the diamond. This is not quite accurate. The total light given out by zircon under X-rays is of the same order as that of diamond. However the zircon radiation has a much wider spectrum band than the diamond fluorescence. Reference is also made on page 322 to the effect of selective milling in small laboratory mills on diamonds. Perfect diamonds are very hard and very strong and are extremely difficult to break. Imperfect diamonds, which form the majority of diamonds recovered from most deposits, although hard, can be very brittle. Even under slight impact some of these diamonds may shatter to powder. Milling conditions must therefore be extremely closely controlled to minimize breakage, and even so, some breakage will always occur. As suggested in the paper, the necessary conditions are: the use of small balls, slow speed mills and very limited water addition. Tests elsewhere have suggested that the water content of the pulp in such a mill must be less than 25 per cent by weight of pulp to prevent diamond breakage reaching significant proportions. The skin flotation techniques described on page 323 operate on a very small scale. It is of interest to note that in West Africa a large-scale continuous skin flotation machine is used to recover the fine diamonds. In this operation the feed is dried and, after standing, is mixed with water and fed in a single layer onto a woven phosphor-bronze conveyor belt. This belt runs at a shallow angle into a water bath and as the particles are carried through the air-water-interface, the diamonds float off and over a weir into a collecting box. The bulk of the particles, being wettable, sink to the bottom of the tank and are continuously removed. If treated without prior drying, the diamond recovery is poor. If material is treated immediately after drying, a lot of the gangue particles also float. During standing, in the hot and humid atmosphere of West Africa, it is found that the gangue particles recover their wettability much faster than the diamond particles. Optimum selectivity is obtained after standing for approximately 24 hours. At the DRL we have been experimenting with optical filters to differentiate between the fluorescence of diamonds and zircon. By limiting the light transmission to the fairly narrow range emitted by diamonds, it is

Jan 4, 1970

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

In 1950, about a third of the world?s population lived in cities. That figure has steadily risen throughout the following decades. Now it is believed that about 60 percent of the estimated 8.1 billion people in 2030 will be living in urban areas. The strain on infrastructure in cities in the developed world is already showing. And the rapid growth in developing nations today is adding to the shortage of materials, equipment and labor needed to keep up with this growth. So, while materials and labor may be in short supply, there is no shortage of work for the underground tunneling and space industry. In June, 718 of those professionals from around the world were in San Francisco, CA for the North American Tunneling (NAT) conference, put on by the Underground Construction Association (UCA) of SME. The attendees spent the three days of technical sessions listening to international authors discuss the state of the industry, new technologies that have become available and updates on major tunneling projects throughout the world. The accompanying exhibit attracted 79 vendors, who displayed the latest in tunneling and underground space equipment and services. In addition to the technical sessions and the exhibit, the NAT featured three short courses ? ?DRB Process Update Workshop,? ?Soft Ground Tunneling Technologies? and ?Underground Blasting Technology and Risk Management.? And the post-meeting field trip to the Devils Slide tunneling project near San Francisco was sold out.

Jan 1, 2008

By Frederick Laist

THE ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaces, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of -copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper;: this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it was found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first-.and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator, produces a product that is self-fluxing; in fact, it is possible to produce a

Jan 1, 1920

The Tertiary gold deposits of the Hauraki area are predominantly epithermal vein types containing mineral assemblages of quartz, calcite, pyrite, sphalerite, galena, chalcopyrite, acanthite and native gold (electrum). Sulphosalt, telluride (eg hessite), seleniferous sulphide and selenide minerals are important locally. Studies of wall rock alteration mineralogy, fluid inclusions in gangue minerals, and sulphur isotopes of sulphide minerals indicate that the ore forming fluids had the following parameters: pH, near neutral at depth but acidic near surface; temperature, predominantly 320 - 270¦C for base metal dominated assemblages, 280 - 200¦C for precious metal dominated assemblages and generally below 200¦C for late stage barite; apparent salinity, six to zero equivalent weight per cent NaCl; and CO2 concentration, generally around one mole per cent CO2. There is fluid inclusion evidence for boiling during mineralisation in some deposits. Moderate values off S2 and FO2 are indicated for base metal and mixed base metal û precious metal assemblages of most deposits by the predominance of pyrite + chalcopyrite over other iron-bearing phases; primary bornite is absent, whereas pyrrhotite, hematite and magnetite rarely occur in the veins. The largest gold û silver deposits formed from solutions in which the sulphur species in solution were predominantly reduced. Near surface environments and some deep, predominantly base metal, deposits were formed from solutions with approximately equal concentrations of oxidised and reduced sulphur species.

Jan 1, 1984

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

"A new method for oxidative destruction of cyanide in industrial waste waters and slurries, such as gold mill barren liquors, tailing slurries and flotation tailings has been developed at the Inca research laboratories. Rapid decomposition of cyanide and related species is attained by treating the waste waters with a mixture of S02 and air at controlled pH and in the presence of a small amount of copper which acts as a catalyst. The approach selectively oxidizes cyanide and metal cyanide complexes, and also removes iron cyano complexes which are not removed by alkaline chlorination.The new method is shown to be less reagent intensive and therefore more economical than alkaline chlorination for treating gold mill and flotation waste waters. INTRODUCTIONOver 90% of the gold mined in Canada is extracted from the ore by ""cyanidation"". Wastes from the process consist of tailings which contain free cyanide, cyanide combined with heavy metals, thiosalts and thiocyanates. Because of the concern over the effect of toxic cyanides on the environment, all cyanide containing effluents will have to be treated in the future to meet certain government set concentration limits."

Jan 1, 1982

By Tellis D. A

An outline is given of the general position of earthsciences information in Australia, the background to development of the Australian Earth Sciences Information System (AESIS) and the role of the Australian Mineral Foundation in developing and co-ordinating the projeot in co-operation with the CSIRO, BMR, National Library of Australia, AGIA, and many companies.Details 'of the system, method and anticipated rate of input (especially of unpublished material at which the System particularly aims), mode of dissemination, and use of the data base are discussed. Information on theAustralian Thesaurus of Earth Sciences and Related Terms and brief details of some 30 earth sciences information collections in Australia is given.

Jan 1, 1977

By Y Zhu, D J. Williams, M O’Neill, C Zhang, X Lei

A cover of inert material overlain by topsoil is required over compacted, seawater-neutralised red mud, a waste product from the refining of bauxite to produce alumina. The cover is to be revegetated, and it is necessary to demonstrate that the potential evapotranspirative-driven uptake of salts from the seawater-neutralised red mud will not impact the revegetation. An instrumented column was designed and constructed to test the evaporation-driven uptake of salts from compacted red mud into an overlying cover material with a thickness limited to 600 mm. The PVC column is 1.2 m high, with a 200 mm internal diameter. The column is instrumented with up to ten of each of moisture, suction, salinity and temperature sensors, together with a data logger, designed and manufactured at The University of Queensland (UQ) in Brisbane, Australia. The sensors were installed through the wall of the column at various depth intervals, with each set of sensors located at quarter points around the circumference of the column. Two pressure transducers were installed in the column to monitor the change of water level due to rainfall and evaporation. The column was filled with compacted red mud to a depth of 600 mm overlain by 600 mm of cover material, both sourced from the Queensland Alumina Limited (QAL) site in Gladstone, Queensland, Australia. The column is installed on a building roof at UQ, alongside a weather station, and will be subjected to the prevailing weather conditions for up to 1 year in the first instance, during which time the weather conditions and sensor responses will be continuously monitored. This paper reports on the instrumented column set-up and the early results obtained from the test.CITATION:Zhang, C, Williams, D J, Lei, X, Zhu, Y and O’Neill, M, 2018. Instrumented column testing of salt uptake from compacted red mud into a cover, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 220–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996

Iron production in one year exceeds that of all other metals combined in ten years. It is a huge industry that started from a modest furnace producing one - two kilograms metal per day to a gigantic reactor producing 10 000 tons per day. The major milestones of these developments are reviewed.

Jan 1, 1999

By P. Ramachandrarao, T. R. Anantharaman

EVER since the technique of quenching metals and alloys from the melt (splat cooling) was perfected a decade ago, it has been recognized that the grain size of products solidified by this technique may be extremely small.' The further observation that fcc metals quenched from the liquid state contain very few dislocations has led to the inference2 that metals are subjected to negligible or no stresses during the rapid solidification characteristic of the "gun" or "piston-and-anvil" technique. Evidence for the incidence of appreciable densities of stacking faults has, however, been obtained in case of some splat-cooled fcc and hcp alloys,3 although not for pure metals. In the light of these earlier observations it was considered desirable to study X-ray line-broadening effects, if any, in fcc metals rapidly cooled from the melt. In the present work pure silver (>99.99 pct), aluminum (>99.99 pct) and lead (>99.9 pct) were quenched from the liquid state from temperatures about 50°C above the melting point by the "gun technique" and the resulting foils were subjected to X-ray examination in a Philips Diffractometer. The quenched foils (up to -10 u thick) did not generally stick to the substrate surface and could be easily transferred to the Diffractometer without introducing any plastic deformation. The profiles of the first five reflections from the foils were recorded in each case with Cu Ka, radiation at the slowest available scanning speed of 1/8 deg per min. To correct for instrumental broadening, profiles were also recorded from the metals annealed in vacuo at suitable temperatures. The integral breadths of the X-ray reflections were arrived at by a procedure described earlier.' There was a distinct suggestion of preferred orientation in the recorded intensities of reflections from aluminum and lead foils. Such an effect was not observed in case of silver. In addition, the integral breadths of X-ray reflections from splat-cooled aluminum and lead were not significantly different from those recorded for the annealed metals. The analysis was therefore continued only for silver where the X-ray line broadening was appreciable. The pure diffraction broadening, B, was evaluated for each X-ray reflection (hkl) from silver from the observed, B, and instrumental, b, breadths with the aid of each of the three equations due to Scherrer,5 Anantharaman and Christian,6 and Warren and Biscoe,7 respectively: Bs= B-b BAC=B- b2/B Table I gives the values of particle size, 71, the lattice strain, E, arrived at by the use of the following well-known relations and on the assumption that all observed diffraction broadening could be attributed to lattice strain or particle size, respectively: E = 1/4 cos ? n= B cos ? where A is the wavelength of X-radiation and 0 is the Bragg angle. As no significant peak shifts or asymmetry could be detected in the profiles from the foils, the possibility of any significant contribution due to twins or stacking faults was ruled out. The absence of faults is by no means surprising since pure silver is known to develop stacking faults only on severe deformation and the stacking fault densities recorded so far for even silver filings have been extremely low.' The very low values for percentage mean deviation from the mean value for the particle size in Table I strongly suggest that all observed broadening in splat-cooled silver can be attributed only to small particle size. This conclusion receives further support from the lowest mean deviation recorded for data computed from the Scherrer equation based on Cauchy profiles that are considered characteristic of particle size broadening. Further analysis for separation of particle size and lattice strain effects was considered unnecessary in view of the very large mean deviations obtained for strain values and also the earlier results suggesting absence of even detectable strain in metals and alloys quenched from the melt. It is to be stressed in this connection that the particles are actually grains and not cells formed by walls of high dislocation density usually encountered in deformed samples. As such, the absence of strains is not surprising. The present results are probably the first to record X-ray line broadening due only to small particle

Jan 1, 1970

By Harmon E. Keyes

Harmon E. Keyes (Chemical & Metallurgical Engineer, Eagar, Ariz.)-Chemical dissolution of chalcocite by acidic ferric sulfate is well known. Resulting elemental sulfur may be oxidized to sulfuric acid by heated ferric sulfate. Laboratory tests at Southwest Experiment Station, USBM, Tucson, generally confirmed stoichiometric relations of 1 part Cu dissolved to 1.750 parts ferric iron reduced, using CP chemicals, dried ore samples, and apparatus cleaned with potable water. Recirculation with open-drainage percolation to increase copper in leaching solvent was followed successfully when appropriate, both in laboratory and Pinto Valley pilot tests. Before 1924 attempts to produce ferric sulfate by aerating ferrous sulfate solution were known. Initial oxidation was satisfactory, but rate slowed below practicality as oxidation progressed and acidity increased. Also, due to hydrolysis of ferric sulfate, a ferric precipitate of hydroxide and basic sulfate resulted. Both laboratory and pilot plant tests gave similar results, regardless of whether CP ferrous sulfate or scrap iron cementation discard solution was used. Rapid oxidation of ferrous hydroxide by air alone is well known to analytical chemists. I demonstrated a process to produce acidic ferric sulfate solutions by precipitating ferrous hydroxide with milk of lime, aerat-

Jan 1, 1973

By John G. Henning

The Porcupine Joint Venture operates the Dome Mine in South Porcupine, Ontario. Dome underground began production in 1910. It is the longest continuous operating gold mine in Canada, producing in excess of 15 M ounces. More than 900 underground stopes have been mined and hundreds of miles of drifts, sublevels and raises developed. Underground mining methods included shrinkage, cut and fill and longhole. Not all stopes were backfilled upon completion, particularly the longhole stopes. The Dome open pit was designed above the underground mine workings such that, as the pit is excavated, it intersects underground drifts and stopes. Potential operational problems associated with the interactions between the stopes and the pit walls may occur, necessitating pit wall redesign, ground support installation and operational rescheduling. Each intersection of the pit with the underground mine workings is closely evaluated to maintain a safe working environment and wall stability. This paper discussed how risks to pit wall stability are assessed, mitigated and monitored.

May 1, 2004

By Johann van Wjk

Mandatory Codes of Practice to Combat Rock Fall Accidents came into force on South African Collieries in 1997. These were drawn up in accordance with guidelines issued by the Chief Inspector of Mines, The Codes of Practice (CoP's) are legal documents in terms of the South African Mine Health and Safety Act 1996. One of the main results Of the introduction of the COP'S from a practitioner's point of view is that they formalized much of what would have constituted a typical visit to an underground section previously. Other important requirements were as Billows: Support rules and Strata Control Standard Procedures were to be drawn tip. Identification of Special Areas (areas requiring a higher level of rock engineering input and with, typically, higher order of support and restrictions on mining geometries), Changing conditions underground to he identified timeously. Implementation of the CoP to he monitored. To comply with these requirements on Ingwe Collieries (a division of BHPO Billiton Energy Coal) it was decided to produce too separate forms to be used in conjunction with each other. The first of these, the "Underground Section Physical Risk Rating" measures the physical conditions in each section whereas the second form, the "Section Perfomance Rating" determines how well the section personnel are Coping with the conditions. This form also pleasures compliance with the Support Rules and Strata Control Standards. Both forms are essentially risk matrices but with various scenarios described, each with a certain weighting. The "Risk and Performance Form" system for bord and pillar operations has by now been used for five years in the Ingwe and Eyesizwe Mining Collieries and has achieved a great deal of acceptance. This system has enabled the quantification of previously subjective observations and has improved the strata control awareness and management of underground mining sections. Amongst other initiatives it has assisted ill reducing the severity and frequency of fall of-ground accidents.

Jan 1, 2002

By Gonzalo Díaz, Diego Mesa, Willy Kracht

"It is well known that frothers affect the amount of water that is transferred to the froth, which has an effect on both the froth stability and the water recovery. On the other hand, since non-selective recovery by entrainment is directly related to water recovery, it can be said that frothers have an indirect effect on flotation selectivity. Recent research on this subject has shown that the non-selective recovery by entrainment, which is characterized by the entrainment factor, is frother dependent. In other words, the entrainment factor is not unique, but depends on frother type.Having different entrainment factors implies that for the same water recovery, the amount of undesired particles reporting to the concentrate may vary if one changes the frother type, which suggests, as a possible explanation, that it is not only the amount of water in the froth what is affected by frother type, but also the froth structure.The purpose of the current work is to study the effect of frother type on foam structure (two phase froth). A quasi-2D cell operated with a slot sparger was used to study the foam structure in the presence of three different frothers: Methyl Isobutyl Carbinol (MIBC), OrePrep®549, and Octanol at the same gas flow rate and reagent dosage. The foam structure was studied using image analysis, and an algorithm based on textural analysis was developed to classify the foams. The results show that it is possible to classify foams according to the frother used, which proves that frothers have an effect on the foam structure.INTRODUCTIONFrothers are usually dosed paying attention to froth stability, condition that is commonly estimated by sight, according to the operator's criteria and experience. This happens because there is not an established procedure or technique for frother characterization, generating qualitative descriptions such as “powerful” or “selective” frothers, which lack of scientific thoroughness and remain under subjective factors. Nevertheless, several works have been done in this line of research. Moyo et al. (2007) classified frothers based on their water-carrying capacity, proving that this characteristic is related with gas holdup and frother type. Previously, Trahar (1981) had related water recovery and gangue particles recovery, defining the entrainment value (ENT). Nowadays it is known that entrainment affects both hydrophilic and hydrophobic because it is not a selective process. In the last decade some studies (for example the one of Konopacka and Drzymala (2010)) delved into different entrainment behaviours dependent mainly on the flotation type (batch or continuous, agitated or columnar, etc.), but there were no studies on the effect of frother type regarding entrainment, since Rahal et al. (2001) argued that the ENT factor was independent of the frother type and concentration, and froth height."

Jan 1, 2016

By M. Z. Dogan, M. S. Celik, G. Onal, O. Ozcan, I. Yildirim

A fluorite ore (51.85 % CaF2) containing high contents of calcite, quartz and iron oxides was upgraded by flotation using a new reagent, oleoyl sarcosine (OS). In addition, quebracho and sodium silicate were used as depressants for calcite and quartz, respectively. The effect of pH, collector and depressants concentrations on grade and recovery was determined with the aim of optimizing the flotation conditions. Application of the two-stage cleaning achieved a concentrate assaying 92.17 % CaF2 with 80.1 % recovery. The Si02 content (0.76 %) was below the required level of 1 % SiO2. The mechanism of interaction between OS and fluorite, as compared to oleic acid, is also elucidated based on the zeta potential measurements.

Jan 1, 1993

By F. P. Haver

The Federal Bureau of Mines developed a 10,000-ampere cell to determine the economic feasibility of producing high-purity electrolytic titanium from mill scrap or offgrade sponge. Operating variables were investigated, matetial handling procedures were established, and the cost of electrorefining titanium was determined. The prototype cell produced premium-grade metal (<100 Brinell hardness number (B.h.n.)) from very impure Kroll sponge at a processing cost of less than $0.60 per pound. Refined metal was deposited at the cathode in the form of coarse (85 percent plus 34-mesh), hexagonal crystals of a titanium when the cell was operated an 850° C. A cathode current density of 1,000 amperes per square foot and a molten sodium chloride electrolyte containing approximately 5 percent by weight of soluble titanium were used. In continuous operation, at the optimum number of ampere-hours, (40,000), the current efficiency averaged slightly less than 60 percent. It was possible to supply large enough amounts of electric current for electrolysis to maintain the temperature of the bath, thus reducing overall power consumption to less than 5 kilowatt-hours per pound of metal refined.

Jan 1, 1961