Search Documents

By K. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 meters (1MPa, tensile strength) in the rock mass, a distance that is sufficient to impact the pit-scale slope over the long term. In addition, the damage zone was calculated using the reasonable assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone ? up to 5.6 meters (30MPa, 30% of the compressive strength) ? indicates that microfracturing can occur throughout the entire rock mass in the blasting area. Finally, an economic analysis was conducted by comparing two reasonably assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond?s law after increasing the blast energy from 180kcal/t to 350kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. An optimal blast design should consider both slope stability (safety) and downstream comminution energy (production).

Feb 23, 2014

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

By Gilbert Sauriol

The mining complex, which the Mines Gaspé division of Noranda Mines Limited has operated in Murdochville since 1954, includes open pit and underground mines, two mills, one leaching plant and a smelter. The under- ground mining uses predominantly a large scale room and pillar method, rooms 15 m wide, 30 m high and 300 m long being common. Ore production is effected by 4.5 m3 front-end loaders and 32-tonne trucks powered respectively by 225 and 325 kW diesels. Daily dust and gas readings show that air quality can be maintained at an acceptable level with much less ventilation than that normally specified. This paper emphasizes the point that air requirements should be based on Air Quality Standards, thus allowing an operation to benefit from favourable conditions or from improvements such as exhaust treatment, fuel alteration, etc.

Jan 1, 1983

By Kyle S. Brinkman, Kenneth L. Reifsnider, Fazle Rabbi

"Mixed ionic and electronic conducting (MIEC) ceramic membranes are HeteroFoaM's which play an essential role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC), oxygen separation and permeation membranes, partial oxidization membrane reactors for natural gas processing, and high temperature electrolysis cells. Dual phase oxygen membranes consisting of an ionic conducting phase Ceo.sGdo.z02 (CGO) and an electronic conductive phase C0Fe204 (CFO) were fabricated and characterized by structural (XRD), microstructural (SEM-EDS) and broadband dielectric measurement techniques. In-situ measurements of the dielectric properties of working oxygen separation membranes are presented which indicate that the material's dielectric behavior can be an indicator for MIECperformance.IntroductionCeramic membranes which transport oxygen ions play an essential role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC) [l ], oxygen separation and permeation membranes in the commercial and nuclear arena [2, 3], partial oxidization membrane reactors for natural gas processing [4], and high temperature electrolysis cells [5]. For the electrolyte functions, the membranes must transport oxygen ions only. On the other hand, permeation membranes, typically used in combustion devices to support oxy-fuel combustion or for partial oxidation reactions involving the production of synthesis gases, require mixed oxygen ion and electronic conduction (MIEC). Traditionally the tailoring of the ratio of ionic conductivity to the materials electronic conductivity, measured as the transference number, has been accomplished by the introduction of aliovalent doping elements creating point defects in the material facilitating the diffusion of charged species. However, several decades of research have not yet produced single phase materials which possess the concomitant ionic and electronic conductivity required for use in membrane separation applications. It is clear that novel ""dual phase"" heterogeneous materials will be required and that the surface reactions of these materials will be of particular importance as the industry moves toward thin films membranes [6]."

Jan 1, 2013

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By T. H. Jeffers

The U.S. Bureau of Mines has developed porous beads containing immobilized biological materials such as sphagnum peat moss for extracting metal contaminants from waste waters. The beads, designated as BIO-FIX beads, have removed toxic metals from over 100 waters in laboratory tests. These waters include acid mine drainage (AMD) water from mining sites, metallurgical and chemical industry waste water, and contaminated ground water. Following the laboratory studies, cooperative field tests were conducted to evaluate the metal adsorption properties of the beads in column and low-maintenance circuits, determine bead stability in varied climatic situations, and demonstrate the beads' potential as a viable waste water treatment technique. Field results indicated that BIO-FIX beads readily adsorbed cadmium, lead, and other toxic metals from dilute waters; effluents frequently met drinking water standards and other discharge criteria. The beads exhibited excellent handling characteristics in both column and low-maintenance circuits, and continued to extract metal ions after repeated loading-elution cycles. Based on laboratory and field data, cost evaluations for using BIO-FIX technology to treat two AMD waters were prepared. Operating costs for BIO-FIX treatment, which ranged from $1.40 to $2.30 per 1,000 gal of water treated, were comparable with chemical precipitation costs.

Jan 1, 2010

By W. V. McKnight

The paper discusses the equipment and methods used to establish some of the characteristics of a braking system. Some typical tests are described and an explanation of the approach used to derive information from the recorder charts is given.

Jan 1, 1966

By Markus A. Reuter, Jacques J. Eksteen

The modelling of bath type furnaces tends to be either fundamental in nature or total empirical "black box models". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Therefore, this paper argues that to understand complex metallurgical furnaces a hybrid approach is the only method to fully grasp the intricacies of metallurgy, to improve operations, economics as well as environmental performance.

Jan 1, 2003

By Robert C. Merritt

This report describes laboratory as well as pilot heap leaching investigations of low-grade sandstone ores from Wyoming, New Mexico, and Colorado. Sodium carbonate-bicarbonate solutions containing sodium hypochlorite extracted up to 86, 54, and 16 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively. Ammonium carbonate-bicarbonate solutions containing sodium hypochlorite were less effective at leaching these ores. Acid leach in replicate pilot plant testing resulted in U308 extractions of 96, 88, and 81 percent from the Wyoming, New Mexico, and Colorado ores. The development of cost-effective processes for extracting uranium from low-grade ore is essential to the assurance of a continuing domestic supply of uranium.

Jan 1, 1977

By Dale Coffin

Definition Of A Crisis Crisis \kri-ses:\ An unstable or crucial time or state of affairs whose outcome will make a decisive difference for better or worse (Webster's New Collegiate dictionary) An event or set of circumstances that could significantly affect a company?s ability to carry out its business, damage a company?s reputation and/or threatens the health, safety and well-being of employees, the community or the public at large You?re Having A Crisis When... . The emergency poses a significant threat to the public or employees . The emergency situation provokes government scrutiny . The company no longer has full control of the situation . The situation has created significant regional, national or international media interest . The corporation?s reputation may be damaged or there is a threat to the bottom line or share value

May 1, 2004

By Meghan M. Murphy, Derek Penrice

The Downtown Rail Extension (DTX) is principal element of the planned second phase of the Transbay Joint Powers Authority’s (TJPA) Transbay Program. When complete, this regionally critical project will connect Caltrain’s regional rail system and the California High-Speed Rail Authority’s statewide system to the Salesforce Transit Center in downtown San Francisco via a 1.3-mile tunnel. Studied since the 1970s, the DTX has now received environmental clearance, and key stakeholders are aligned on the project’s configuration and its expedited delivery. This paper describes efforts to optimize the DTX configuration and develop an informed project delivery strategy that incorporates construction industry feedback on project phasing, contract packaging, and procurement methods that accomplish the project’s budget goals.

Jun 13, 2021

By C. E. Gregor

Current modern trends in mining show that hoisting shafts are being expected to fulfill an important ventilation function. However, where rigid guides and supporting structures are mandatory, ventilating power costs will be high, unless the transverse structures (shaft sets) are streamlined. In the complex configurations of hoisting shaft furniture patterns, either for original design purposes, or for the adjustment of an existing shaft, a useful degree of aerodynamic optimization, by reduction of overall resistance, can only be effectively evaluated by model studies in a special purpose wind tunnel, as described herein. The author has shown that, in one particular case, an annual power cost saving of more than $50,000 was indicated, mainly by the selection of buntons and dividers of improved aerodynamic profile. Mining companies are now realizing the advantages that can accrue through proper attention to the aerodynamic aspects of mine shaft design. With progressive demands of civilization for an ever greater supply of coal and metals, and with greater depths of working, higher rates of extraction, advanced degrees of mechanization, and improved standards of environmental health and work comfort, shaft design is becoming an extremely important aspect of mining operations. In addition, because the cost of sinking, equipping, maintaining, and operating a mine shaft is continually increasing, there is a greater incentive to use a shaft for the maximum duty, consistent with economy. The current natural tendency is therefore to sink multi-purpose shafts, to install as much equipment as is safely and effectively possible to operate; and then, over and above all these functions, to use the shaft to its maximum possible ventilating capacity, as a major, or auxiliary, airway. Clearly, this latter additional function can only be employed at a significant cost, since the most economic operating airways are smooth-lined and devoid of internal rigid furniture. It is true that hoisting functions can be carried out in such shafts if rope guides are used, but only under restricted conditions. Where a manway must be provided, fixed guides and supporting structures are mandatory, and ventilation costs become accentuated. It is generally recognized that the prime element of cost in ventilating a mine can be represented by the power required to drive the fan unit. It is also known that the largest component of total mine resistance is that of the downcast shaft, where this shaft is equipped with rigid guides for hoisting purposes. The pressure loss varies directly as the resistance of the shaft, in accordance with a modification of the Atkinson equation p = RQ2/3600. Furthermore, the air horsepower drawn is given by the equation AHP = (p x 0/33000. Therefore, the power required to drive the fan unit varies as the resistance of the shaft and the cube of the air quantity. Clearly, if Q is a specified minimum, then the only way to minimize the pressure loss (and the power costs) is to reduce the shaft resistance R. (See Table I for a list of symbols.) The resistance to airflow of a shaft equipped with rigid guides and supporting structural sets consists of two components which, for the sake of analytical simplicity, can be regarded as additive. 1) Frictional resistance, represented by the viscous frictional forces within the boundary layer, as air flows along the surfaces of the walls and the periphery of the vertical elements (guides, pipes, cables, ropes, etc.) of the furniture. The friction loss can be readily calculated by the Atkinson equation, after selection of a suitable value for the friction factor K from the McElroy compilation.' KxLxO xQ2 5.2 xA3 Friction loss can be minimized by lining the shaft walls (particularly if of circular or elliptical cross-section) with a smooth continuous lining of monolithic concrete.

Jan 1, 1968

By Vincent C. Smith, Agit Singh, Bernard Muller

The control of minerals processing plants is by no means trivial. In order to address some of the difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written to test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimising algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. The controller was tested for various scenarios that are often encountered in the minerals processing industry. When problems were encountered, the MPC algorithm was specially adapted to accommodate for these difficulties. Control was further improved by using feedforward control as well as quadratic programming. The movement of the manipulated variables was reduced by using a region of uncertainty that allows the controlled variable to vary within a specified region around the setpoint. Integrators were handled by adapting the algorithm slightly and adding an optional integral error portion in the MPC controller. The performance of the enhanced MPC controller was compared to PI controllers on both the simulator and a commercial plant. The MPC controller showed faster responses with less interaction in both cases.

Jan 1, 2003

By AIME AIME

LIFE in few countries is dominated by geographic conditions to the degree that it is in Peru. The broad plateau of the Andes, bordered by lofty ice-clad ranges with deeply eroded flanks, imposes a pattern on the region to which most human activities must conform. On the Pacific side, desert conditions prevail, interrupted only by irrigated valleys along rivers that descend from the highlands. Above seven or eight thousand feet the rocky ridges become grass covered, and the central zone is one of high pastures with cultivation in the valleys or on terraced slopes except at altitudes over 15,000 ft. where glaciated landscapes prevail. Each of the three belts has its own distinctive resources and climate, and each its own special ways in which its inhabitant, must make a living. The Pacific region is one of the most arid regions in the world. Except for the irrigation, the country is an unmiti¬gated desert. The climate, in spite of the tropical latitudes, is mild with the heat relieved by air from the adjoining cold ocean. Fogs are prevalent throughout the winter months but precipitation is scarcely measurable. Ideal conditions exist for cultivation of sugar and cotton which are the dominant crops. Lima, the capital. situated in one of the most productive valleys, is an impressive city which in its modern development is well maintaining the high position it held when it was the

Jan 1, 1945

By Jessica Egan, Daniel Hodouin, Claude Bazin

"The recovery of gold by leaching is influenced by the size of the gold carrier particles and the chemical environment. Using the relationships between the leaching rate, infinite recovery and particle size for a given set of chemical conditions, it is possible to simulate gold recovery for various feed size distributions. However the use of these particle size relationships is only valid if the leaching of gold from a given size class is independent of the production history of this size class. For instance, to use these relationships it is necessary to verify that gold recovery from the leaching of the 200-270 mesh size class remains the same if the size fraction is taken from a coarse or finely ground ore sample. Several laboratory tests were carried out to answer that question. Results of the tests show that within the large error margin associated to gold content measurements, the history of the production of a size class does not affect the gold leaching from that size class. Emphasis of the discussion is put on the difficulty associated with the processing of data containing significant measurement errors as it is the case for gold assays of leaching tests.INTRODUCTIONMore than 75% of the gold produced in the world is extracted by cyanide leaching of gold ores. The ore is ground to expose the gold carriers and the ground material is reacted in an oxygenated cyanide solution that dissolves gold, leaving solids gangue minerals that are disposed to tailings ponds or returned in underground mines as paste fill. The gold contained in the solution is recovered by either the carbon in pulp process or by cementation onto zinc powder, before being melted and casted into a brick (Marsden and House, 2006)."

Jan 1, 2009

By B. Mishra

Calcium and lithium gallides have been synthesized by powder metallurgy techniques in the stoichiometries that can be used as reduction alloys for the Rocky Flats Plant Salt-Scrub (SS) process. The SS process is performed to recover valuable metals from salts generated in the electrorefining and the molten salt extraction processes. Combustion synthesis has been optimized for variable heating rates up to the reaction ignition temperature and for green densities of the powder compacts in terms of the ignition temperature and the exothermic heating of the product in an effort to develop LiGa and CaGaz alloys. The problems arising from the melting point and density differences of calcium, lithium and gallium have also been studied. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. The efficiency of the intermetallic alloy, Ca-17 wt. pct. Ga, as a reductant and the effect of gallium on salt clean- up has been discussed. Measurement of actinide recovery has been studied with cerium as the surrogate for the actinide metal. The development of an alloy for SS reduces a major contaminated waste disposal problem besides recovering the valuable reactive metal.

Jan 1, 1993

By H. M. Lima, L. A. Gomiero, C. A. de Morais

ABSTRACT The Caetité-Brazil uranium facility produces approximately 400 tonnes U3O8 per year from an ore averaging 0.29% U3O8. The process steps are ore crushing, heap leaching with sulphuric acid, uranium separation and purification by solvent extraction (SX) with a tertiary amine, followed by stripping with a sodium chloride solution, precipitation as ammonium diuranate (ADU), and product drying. A change in the milling process is being evaluated to increase production and uranium recovery. Heap leaching will be replaced by conventional agitated tank leaching of the –590 µm ground ore slurry in a sulphuric acid medium. Replacement of the stripping reagent is also being considered.

Jan 1, 2012

By Jacques J. Eksteen

Any effort to improve the metallurgical control of industrial furnaces employed in the primary extraction of high carbon ferroalloys are bound to fail unless the variability of the melt is not fully accounted for. A number of sampling campaigns were performed on both 3phase AC submerged arc and single phase DC open arc furnaces at different smelter sites in South Africa where High Carbon Ferrochrome is produced. It was found that the heterogeneity between multiple samples during a single taps were much higher that for heterogeneity found within a sample. Moreover, this heterogeneity (as quantified by the relative standard deviation per tap) varied with the operating conditions of the furnace, the element monitored and the type of furnace. A relationship was found between the relative standard deviation of certain elements and the degree of subcooling of the melt.

Jan 1, 2006