Search Documents

By Ben E. Lusk

First of all let me say what a genuine pleasure it is to be here. Acapulco certainly is a beautiful change. I'm going to spend sometime talking about change, because frankly I'm astounded at the rate of change in our world today. One good example of this, reminds me that the first time I spoke before the AIME two years ago, we were at the Ramada Inn in Beckley, West Virginia. Today we're at the Princess Hotel in Acapulco, Mexico. Now that's what I call a change. Seriously though, I'm sure you've all heard it said that the most consistent thing about our society is its constant change. Five years ago, no one could have predicted the changes we experienced in the United States during the first half of the 1970's. In the past twenty-four months alone, we have seen two presidents, three vice-presidents and hundreds of administration and government personnel changes. We have stumbled from one social crisis to another, while suffering through rising inflation, major energy shortages and labor unrest that could plunge us into a full scale economic depression. In view of these constant and unpredictable changes around us, it's obvious that we must learn to deal with change and "roll with the punches" if we are to survive. A controversial book published recently, explores in detail the various aspects of change and its impact on man.

Jan 1, 1974

By X. Xu

This paper presents the research on comprehensive recovery of copper, gold, silver and iron from tailings from high-intensity magnetic separation in Tonglushan Mine. By comparison of experimental results of three flowsheets?regrinding of tailings-conventional sulphidizing flotation, water heating enhanced sulphidizing flotation and acid leaching-sulphidizing precipitation flotation, it is concluded that regrinding of tailings-conventional sulphidizing flotation flowsheet has the best economical and technical performance and practicability. Regrinding and using the mixture of sodium hydroxamate and sodium xanthate are two of the notable technical characteristics of this best flowsheet. The system for comprehensive recovery of tailings has been put into production. It not only can recover the valuable minerals from tailings in Tonglushan Mine, but also can reduce the environmental pollution, resulting great economic and social benefit.

Jan 1, 2014

By M. R. Julien, A. Maqsoud, J. Martschuk, B. Bussière

Acid mine drainage (AMD) from mine wastes is one of the most challenging environmental problems currently facing the mining industry. When mining wastes have the potential to produce AMD, the effluents produced have to be managed to meet existing regulations on water quality. The LTA impoundment (property of Barrick Gold Corp.) located near Malartic, Quebec, contains sulphide tailings that have the potential to generate an acidic leachate. The closure option selected by Barrick was to construct a cover with capillary barrier effects (CCBE), in which the moisture- retaining layer is made of non-acid-generating tailings. Since its construction in 1996, the cover has been monitored to evaluate its performance. For that purpose, various parameters have been measured, including the volumetric water content and matric suction in the different layers of the cover. This paper presents some of the main results from the monitoring program that started eight years ago. The results show that the cover is able to maintain a high degree of saturation in its moisture- retaining layer, acting as an oxygen barrier. The actual performance of the CCBE on the flat surface of the 60 ha site is better than expected at the design stage. The only concern with the LTA cover is the effect of slopes that can reduce the performance of the CCBE during dry periods. However, these effects appear only for short periods of time, and are limited to very localized areas, so that they do not significantly affect the overall performance of the CCBE and its ability to limit the production of AMD.

Jan 1, 2006

By L. J. Defferding

This report documents the work performed by Battelle-Northwest and its sub-contractors in Phase I of a project to develop a cross pit conveyor system for the Bureau of Mines. The conveyor system description includes details of the conceptual design as well as system and component specifications. The selection of primary and back-up sites for system demonstration is discussed. Maneuvers and operating sequences required for mining the selected demonstration site are described and illustrated in detail. Economic viability of the cross pit conveyor system was analyzed by estimating the cost of overburden removal per ton of coal using the Battelle-designed concept and comparing these costs to the cost of an available state-of-the-art 30-yd3 dragline operation. Testing and trade-off studies conducted are documented and the results presented. Alternate designs considered in developing the selected cross pit concept are included for completeness. Based on the evaluation of the selected concept, it was concluded that the cross pit conveyor system proposed by Battelle is a technically and economically feasible overburden handling method with a good potential to improve western coal mining efficiency.

Jan 1, 1976

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By Manfred Krutein

Ocean mining has a number of problems which are critical to its development: ? Political hurdles on national and international stages ? The worldwide economic situation, with the possibliity of a recession ? Financial difficulties in funding further work ? Technical problems for the development of ocean mining and transport subsystems ? Demands for technology transfer This paper touches the last two points and provides some thoughts for discussion and creative objectification. The many technical problems of ocean mining will be identified and some proposed solutions will be investigated relative to the state-of-the-art technology of ocean mining and nodule transport. An outlook into the future attempts identification of the steps necessary to eventually develop components for workable systems that are not only technically but also economically feasible.

Jan 1, 1978

By M Frenzel

At the last MassMin Conference in Sudbury, Caterpillar’s vision of a continuous mining concept for block caving operations was presented on the background of global raw material demand and its continuous increase. By analysing today’s structure of mining processes in block caving, the paper (Krings, Steinberg and Frenzel, 2012) highlighted the main bottlenecks in the process chain and identified conceptual solutions by help of a case study. The main focus was the paradigm shift from discontinuous batch type operation to a continuous mining process of the blocks.In 2016, the strategic vision has taken major strides forwards and remote continuous operation has become a reality. Caterpillar’s continuous operation system – the Rock Flow system – was successfully installed in Codelco’s Andina mine and start of operation is scheduled in the first half of 2016.Based on continuous product developments, this paper sets the focus on two main aspects of continuous mining. First, field experiences of the Rock Flow system will be shared, highlighting the Andina project course from system installation, to commissioning and successful system start. The second aspect concentrates on the system and mine layout as discussed in the case study scenario in MassMin 2012 (Krings, Steinberg and Frenzel, 2012).Based on Caterpillar`s continuous product development, the Rock Flow system set-up and panel design were modified for a general roadway design and drawpoint layout. The new design allows an optimised use in block preparation phase (spreading) and full production phase (reaping), operating a fleet of load-haul-dumps (LHDs) and Rock Flow systems. The combined use of the two technologies optimises the mining process in every stage of block life and significantly increases the performance of the continuous block caving operation in the production panel to pave the road for the next generation of super caves.CITATION:Frenzel, M, 2016. New continuous production system in block cave mining – the rock flow system, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 543–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Xiangwen Wang

Electrochemical measurements associated with the electrowinning of lead metal from concentrated brine (NaCI) - lead chloride (PbCI,) electrolytes at temperatures in the range 328 to 353°K (55 - 80°C) were conducted. The electrodeposition of lead metal onto a lead rotating-disk electrode may be described by the electrodic reaction: {PbCl 4 2 + 2e- = Pb° + 4Cl-} The deposition-overpotential requirements are low (approximately 41mV per decade of current density - Am+), with a corresponding high exchange current (approximately 0.018 A.cm2). The diffusion coefficient of the electroactive PbC142- species in a 3.5 NaCl electrolyte at 353°K was insensitive to the total PbCI, concentration (0.01 to 0.1M), and its value was found to be (1.21*0.1)~10-5 cm2Is with a temperature-sensitivity coefficient (E,/R) of approximately 1.98x103K-1 (328OK(T<353OK).

Jan 1, 1993

By Shoji Taniguchi, Lifeng Zhang, Kaike Cai

"In the present paper, based on the two-phase (Eulerian-Eulerian) model, the 3D fluid flows in gas-stirred systems, i.e., air-stirred water vessel and argon-stirred liquid steel ladle, are simulated. In the Eulerian-Eulerian two-phase model, gas and liquid are considered to be two different continuous fields. The phases are assumed to share space in proportion to their volume fractions. The exchange between the phases is represented by source terms in conversation equations. Turbulence simulated by the k- e model is assumed to be the property of the liquid phase. The following effects of mathematical treatments and operational factors on the fluid flow are discussed, such as interphase drag force, turbulent model, the size of bubble, and gas injection mode.Some interesting results are derived. Except the interphase drag force, the interphase lift force should be taken into accounted in order to exactly simulate the fluid flow in gas-stirred systems. Suitable turbulent model and drag coefficient have effect on the mathematical simulation. Injecting small bubbles can realize a well mixing flow condition. The distance between the two gas-injection nozzles has effect on the fluid flow."

Jan 1, 2000

By Liwen Hu, Jianxun Song, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

The subchloride titanium was prepared by sponge titanium and titanium tetrachloride in the CaCl2 at 1173 K. The species were detected are mainly titanium dichloride, and the average valent in the melt are 2.05. The accurate equilibrium constants were obtained for the reaction 3Ti2+ = 2Ti3++Ti after the accurate activities of titanium chloride were evaluated with emf method, and the observed deviations from ideal behavior are discussed.

Jan 1, 2015

By Edmund S. Leaver

[In previous reports 5/ of ore-testing studies standard methods of conduction tests with precious-metal ores selected as representative of certain mining districts were discussed in considerable detail.]

Jan 1, 1941

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By Richard P. Cislo

The evaluation of the effectiveness of the time domain Coal Interface Detector developed by the General Electric Company under contract H0155120 is the subject of this report. The sensor utilizes differences in the time characteristics of shearer vibrations as sensed by an accelerometer mounted on the ranging arm to discriminate the cutting of coal and rock. Pour identical time domain sensors were supplied by the Bureau for field evaluation. The performance of the time domain sensor was evaluated by an extensive field test and data collection program that included four longwall mines and a total of nine mine visits. The intent was to determine the sensor&apos;s applicability to a wide range of mining conditions and to document its limitations. Results of the extensive field tests indicate that shearer vibration data processed by GE&apos;s time domain signal processing algorithm cannot be used to reliably detect when the cutting drum crossed the coal/rock interface.

Jan 1, 1987

By Hiroyuki. Fukuyama

The pseudo-binary phase diagram of the cuspidine (3CaO2?SiO2?CaF2) - CaF2 system has been studied by electron probe microanalysis (EPMA) and X-ray diffractometry (XRD). To prevent fluorine loss in the form of a HF gas by a reaction of CaF2 with water vapor at elevated temperatures, the equilibrium experiments were conducted with the sample hermetically sealed in a platinum tube. By employing this technique, it was successfully revealed that cuspidine exists as a stable phase and congruently melts at 1684 ± 1 K, and the cuspidine - CaF2 system presents a simple eutectic type of phase diagram, of which eutectic temperature has been estimated to be around 1540 K, corresponding to the composition of 40 mass% 3CaO?2SiO2 - 60 mass% CaF2?

Jan 1, 1999

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By H. Thomasson

This paper will deal with on-site maintenance welding using the stick electrode, electric arc process. It is primarily concerned with the underlying principles, the application of which, or the lack of such application, governs the success or failure of the operation. It will discuss first the base metal or item to be welded, including the field identification of its weld-ability and the determination of the procedures to be followed. Second, it will outline heat effects and the interrelation between heat applied as part of a welding operation and heat deliberately applied as part of a heat treating cycle, stressing the fact that in welding the same basic principles are effective. The third consideration will be weld metal and its control of both composition and properties. Last, but not least, distortion, shrinkage and residual stress will be considered and practical means for minimizing their adverse effects outlined.

Jan 1, 1967

By G. L. Hopps

Various chemicals, including compounds of copper and lead, were added to a mixture of No. 2 and No. 6 fuel oils that was fired in an experimental furnace. Tests were made to determine (1) the effectiveness of these chemicals in removing soot deposits on probes devised to simulate heat-transfer surfaces in boilers and (2) the effectiveness of the chemicals in preventing the deposition of soot on the probe surface. Test conditions were regulated so that the temperature of the products of combustion adjacent to the probes was in the range of 625° to 700° F. The clean-metal temperatures of the air-cooled probes were comparable with the water-tube temperatures in boilers operated at 40 to 100 p.s,i.g. The dosages of the fuel oil additives used in these tests were generally larger than those usually recommended for most proprietary compounds.

Jan 1, 1962

By Frank E. Sullivan

The separation of liquids from granular materials has been widely studied by a number of: investigators over a period of years in an effort to more fully understand the physical phenomenon which occurs. Liquid may be removed from solids, or partially removed, by gravity separation, mechanical separation&apos; or heat drying. Mechanical separation is advantageous when compared to heat drying principally from a cost saving standpoint and also on certain materials which are heat sensitive. It is realized however that mechanical separation of liquids has certain practical limitations. In order to evaluate the efficiency of mechanical separation and predict the extent of, liquid removal, it is first necessary to study the forces which hold the liquid to the solids. From a very practical observation using gravity drainage, it is soon obvious that a pile of coarse solids will drain faster and retain less liquid than a pile of finely divided solids of the same material. For commercial operations it is important to estimate the residual liquid which will remain after a mechanical separation. Batel (1) explored the various quantities of liquid present in the interstices of the bulk granular material. From his work and other authors which he has correlated in one of his recent papers, various formulas are now available which permit an empirical relationship to be developed showing residual moisture versus mechanical separating forces.

Jan 1, 1965

By Greg Border

Many unique ventilation problems have been faced as Avery Island Mine&apos;s large openings have been mined. High humidity of outside air combines with the hygroscopic salt to create a corrosive atmosphere. Massive rooms preclude routine use of brattices to direct air flow to the working faces. Large amounts of explosives are consumed in single blasts. Resulting concussion pounds air control structures and ANFO ignition creates large amounts of nitrogen dioxide in single rooms. Geologic constraints confine new shafts and slopes to areas thought to be free of potential ground water hazards. Dust control techniques are limited by dry product demanded by customers. The Avery Island Mine&apos;s ventilation system has evolved to deal practically with the conditions and to dependably provide fresh air to the miners. International Salt Company&apos;s Avery Island Salt Mine, a multiple level room and pillar operation, has been mined steadily since about 1900. It is known as one of the "Five Island" salt dome mines of South Louisiana&apos;s Gulf Coast. Production from the area places Louisiana first in United States rock salt mined tonnage, according to the United States Bureau of Nines, 1982 (1). International Salt Company is a major force in U.S. salt production, as it also operates mines in Detroit, Michigan; Cleveland, Ohio; and Retsof, New York; a solar salt facility in Bonaire, Netherlands Antilles; and a solution mining plant at Watkins Glen, New York.

Jan 1, 1983

By S. Hoerger

Newmont has a large integrated operation in Northern Nevada with numerous mines, stockpiles, and processing facilities. There are over ninety defined metallurgical ore types and over sixty defined gold recovery process options. To take better advantage of the available synergies, a complete Nevada wide mine plan and process model along with a mixed Integer and Linear Programming optimization tool has been developed and implemented. This system is maintained and operated by a Nevada Planning Group. Standard in-house planning software tools and methods have been implemented at all mine sites. While increasing the effectiveness of planning in Nevada, these changes have allowed a significant reduction in overall Mine Engineering staff.

Jan 1, 1999