Search Documents

By Corey Vaughan

Unplanned shutdowns from abrasive wear part failure in crushers, chutes, and slurry pipe assets can cost millions in lost production and reactive maintenance. 2Censor patented sensor technology enables real time abrasive wear monitoring of mineral processing equipment, turning passive assets into smart, data driven components. Wireless sensors embedded in liners and pipework transmit wear data live to operators, allowing for predictive maintenance, safer scheduling, and optimized asset life. This paper will present global case studies showing reductions in downtime, increased throughput, and improved maintenance accuracy. The system is ready to retrofit, neutral to original equipment manufacturers, and proven across more than twelve countries in abrasive wear liners and slurry pipe applications.

Feb 22, 2026

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By Alfredo Valencia-Toledo

This study delves into the satisfaction levels of indigenous communities in Apurimac-Cusco, Peru, concerning mining activities in their region. Our primary objective is to elucidate the interrelationships among observable variables, which are conceived as linear combinations of multiple factors. Employing the statistical methodology of exploratory factor analysis, we aim to pinpoint the pivotal factors influencing the progress of mining activities in Apurimac-Cusco. Through our analysis, we have identified eight key factors that exert a significant impact on mining’s sustainable development in the area. These factors encompass diverse facets, ranging from the support offered by mining company to communities, environmental considerations, education, economic factors, provision of basic services, transportation and communication, support for social organizations, and social-health-related aspects. This research endeavors to provide a comprehensive understanding of the complex dynamics surrounding mining activity satisfaction among the indigenous population, offering a basis for further exploration and policy development.

Feb 17, 2024

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By Ron F. Schritt

Over the many years since the development of the steam powered shovel, various powering and control techniques have been employed for the various shovel functions. While volumes have been published on this subject, this paper will be limited to a very brief discus-sion of one of the latest of these and its application to a unique machine. The evaluation of the subject machine is far beyond the scope of this discussion, which will be limited to the techniques and equipment employed, and the considerations involved in their choice. The basic requirements for any power and associated control system for any power shovel function have remained relatively un-changed over the years. To the extent possible, such an equipment grouping must be: Easy to install during fabrication Easy to maintain and repair by available personnel Life cycle cost competitive Adequately reliable Adequately responsive And as may be expected these factors are arranged in various orders of priority by different manufacturers and users. All the various time honored approaches have to some extent fulfilled these require-ments but were discarded or fell into disuse when more effective approaches were developed. The latest in this long line of develop-ments and perhaps the most promising is that of electro-hydraulic controls and hydraulic drive.

Jan 1, 1977

By N Lefebvre, M Jakeman, R Aseervatham

Semi-arid regions suffer from two afflictions; evaporation may exceed precipitation by multiples of two or more and variations in precipitation can be both extreme and difficult to predict. Many Australian mines are situated in semi-arid areas where communities are reliant upon locally sourced water or special purpose infrastructure is built as part of the mine construction. As the question of climate change looms, issues related to future water supply and sustainable water management become increasingly important. Across Australia several mining operations co-exist in a single surface water and/or groundwater catchment area. The management of water on a mine by mine or a community by community basis is illogical and must be reconsidered based on a single water catchment and a whole-of-community basis. Mine water should be considered on a full life cycle basis where the quality is assessed for specific mine site applications. This paper addresses technical challenges that include surface water and groundwater supply in semi-arid regions, operational water in the mining industry, beneficial uses of water, water economics and demand management. In much the same way as emissions trading evolved into a multi-stakeholder forum, mining regions offer scope for innovative thinking in water supply and reuse. In addition, this paper considers a number of initiatives taken by Australian mining companies that are entering a prefeasibility stage and contrasts these initiatives against the established success within a South African mining region. The challenges and potential solutions to this initiative are presented for future consideration.

Jan 1, 2006

By Michael J. Peacock

The Powhatan No. 4 Mine is located in southeastern Ohio along the Ohio River in Monroe County. The mine produces approximately 3.2 million tons of steam coal annually from the Pittsburgh No. 8 seam. The Pittsburgh No. 8 seam in this area dips to the southeast in varying amounts from 10-feet to 40-feet per mile. The seam is made up of a main bench coal (4' to 5f' ) containing several thin and variable partings and a rider ("roof") coal (0" to 18") which is separated from the main bench by a parting (0" to 18") that is reasonably consistent in occurrence and position. Strata overlying the seam varies from a bedded to nonbedded calcareous mudstone-claystone (6' to 12') in the north and east regions of the mine to a sandstone (Pittsburgh Sandstone C10' to 40'1 in the south and west regions. The Redstone Limestone (10' to 18' ) overlying the mudstone-claystone in the north and east thins and rises toward the area of sandstone deposition in the south and west. From its opening in April of 1971 until late 1981, primary roof support in the long-1 ived entries at Quarto Mining Company's Powhatan No. 4 Mine had been achieved with 8-foot and 10-foot. 518-inch mechanical roof bolts using a Single expansion shell. These bolts were installed so that the expansion shell achieved a competent anchorage in the limestone. However, as the mine developed westward, the limestone began to trend upward becoming inaccessible as an anchorage medium at the 8-foot and 10-foot horizons. Anchorage achieved in the underlying mudstone-claystone strata was failure-prone due to weathering (after exposure to air and moisture) and inconsistencies in the anchorage horizon, leading to an increase in the incidence of reportable roof falls at the mine. Responding to the threat to safety and productivity posed by the increase in roof falls. Mine Management through its Safety and Engineering Departments, sought solutions to the problem. In seeking a solution to the problem, the safest and en engineering groups examined the reportable roof falls to determine the cause of those failures. Their examination pinpointed two items which were found to be a common link in the majority of those falls; namely, anchor integrity and geologic trends. Analysis of the roof falls indicated that due to effects of air and moisture on the anchoraae zones in the mudstones and clay- itones, the integrity of the anchorage over time could not be maintained. Geologic trends noted included the upward trend of the -main limestone as mining progressed westward, inconsistencies in the amount of roof coal and draw slate in the immediate mine roof and increasing evidence of heavily slickensided immediate mine roof. In the absence of the protective barrier provided by the roof coal, the immediate strata and particularly the draw slate, is susceptible to deterioration due to the weathering effects of air and moisture and thus is prone to "eat out" around the roof bolts and cause roof falls. The presence of heavily slickensided roof creates a need for increased contact surface such as that provided by plank and header blocks to aid in holding up the roof and tends to make the behavior of such roof very unpredictable. Having determined the causes of the roof falls. Mine Management began to identify the kind of roof support which would best solve these problems, while at the same time providing the mine with a safe, cost effective and efficient roof support system. This paper will provide an analysis of how this decision was reached, the background that was researched to aid in forming the decision, the considerations that played key roles in the formulation of the plan, the mechanics of following through and implementing the new roof support system, and an assessment of the resultant gains in safety, productivity and improved costs derived from the implementation of the new roof support system.

Jan 1, 1986

By C Rizos

Many of the ‘new paradigms in mining’ and notions of ‘sustainable mining’ have at their core the requirement for reliable, continuous centimetre-level positioning accuracy to enable increased automation of mining operations. The deployment of precision systems for navigating, controlling and monitoring machinery such as drills, dozers, draglines and shovels with real time position information increase their operational efficiency, and reduce the need for humans to be exposed to hazardous conditions. The Global Positioning System (GPS) is the best known, and only currently fully operational, Global Navigation Satellite System (GNSS) providing positioning capability anywhere in the globe, on a continuous 24/7 basis, with accuracies ranging from the dekametre-level to the sub-centimetre-level depending on hardware and operational configuration. Despite this versatility, GNSS cannot satisfy the high accuracy positioning requirements for many applications in mine surveying, and mine machine guidance and control. The reason is that increasingly open cut mines are getting deeper, resulting in a reduction of the ‘sky-view’ necessary for GNSS systems to operate satisfactorily. Yet, to date there have been no viable alternatives to GNSS that can be deployed in mine environments that can meet the challenging requirements in open cut mines.Locata Corporation, a Canberra-based company, has invented a terrestrial high accuracy positioning system known as ‘Locata’ that can augment GNSS with extra terrestrial signals to permit cm-level positioning accuracy even when there are insufficient GNSS satellite signals for reliable positioning and navigation. Locata relies on a network of synchronised ground-based transceivers that transmit positioning signals that can be tracked by suitably equipped user receivers. Hence Locata can be considered a new type of ‘local constellation’, able to provide high accuracy positioning coverage where GNSS fails. This paper introduces some of the technical aspects of this Australian technology and describes tests conducted by Leica Geosystems over the last few years at Newmont Boddington Gold in Western Australia. A recent news announcement by Leica Geosystems (12 January 2011) has confirmed that their new mine management system will have combined GNSS + Locata positioning capability – the first commercial product that integrates GNSS and Locata capabilities into a single high accuracy and high availability navigation device for open cut mine machine automation applications.

Nov 22, 2011

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

By Ava Segal, Doga Cagdas Demirkan, Abhidipta Mallik, Sebnem Duzgun, Andrew J. Petruska

Search and rescue operations in mining heavily rely on humans. In the context of emergency situations within underground tunnels, the potential to utilize sensory technology for navigation assistance holds the promise of saving human lives. Our research introduces a device configuration designed to enhance the performance of search and rescue teams. This setup integrates LIDAR and thermal cameras with the Microsoft Hololens, facilitated by the NUC computer and ROS Bridge. Performance assessment involves quantifying the extent to which a user is willing to venture into a light-deprived section of the mine prior to necessitating supplementary illumination. The preliminary outcomes highlight the significant potential of augmented reality assistance in offering indispensable aid to first responders, thereby greatly augmenting the efficiency of search and rescue missions conducted during critical circumstances.

Feb 1, 2024

By Kefton H. Teague

An article entitled "The Rule of the Geologist in the Industrial Mineral Field" by G. R. Gullet, was published in the August, 1967, issue of the Canadian Mining Journal. Mr. Gullet defined industrial minerals as follows: "Industrial minerals are largely non-metallic minerals and rocks that find value because of their physical or chemical properties." This definition is brief, but all-inclusive. Mr. Gullet continues, "They include all useful minerals and mineral commodities except those used as fuels and those from which metals are extracted. Factors in the evaluation of an industrial mineral deposit are generally as different from those used in the evaluation of a metal deposit as is the assessment of a potential oil field. The key to the successful development of an industrial mineral, deposit is more often a balance of accessibility, transport, and proximity to markets than to any natural quality advantage of the deposit itself."

Jan 1, 1972

By Oliver W. Marsden, John O. Marsden

This paper presents the results of a hypothetical case study that evaluates the potential transition of a large copper mining and extraction operation to 90% renewable energy. The case study considers three phases to accomplish such a transition; phase I considers installation of renewable power generation at the site to meet a portion of the current electric power needs, phase II considers conversion of diesel combustion mining equipment to electric equipment, and phase III considers implementation of renewable energy generation coupled with energy storage systems to provide approximately 90% of the total mine site energy requirements. The paper evaluates the results in the context of a range of purchased electric power unit costs ($0.065, $0.100, and $0.135/kWh) as well as various carbon tax scenarios ($0, $5.00, and $37.30/t CO2). While the case study is hypothetical and considers a range of assumptions, it clearly identifies a pathway to potentially economically viable transitions to a renewable energy platform for mining companies. This represents an approach that mining companies can use to help to meet emissions targets, as well as social responsibility and reporting requirements.

Jun 4, 2021

By David C. Lynch

FeCl3 particulate of 10 to 100 um in diameter was reacted with radicals produced in an oxygen plasma at pressures between 1 to 20 Torr. The particulate, in a fluidized bed, was positioned above the plasma to avoid over heating the oxide product which is known to lead to crust and clinker formation[ 1 ]. Reaction between the iron chloride and the gas phase occurred at temperatures between 66 and 226 °C. Oxygen radicals react with the surface material to a depth of approximately 2.5 4m. Surface material, analyzed with a x-ray technique, indicates that the maximum amount of FeCl3 reacted on a weight basis was found to be approximately 67%. More typically, 40 to 50 wt% of the chloride was reacted within 30 minutes to 1 hour.

Jan 1, 1996

THE first session of the Institute was held on Tuesday evening, September 16th, in the William Molson Hall, of McGill University, Dr. T. Sterry Hunt, Chairman of the Local Committee of Arrangements, in the chair. Dr. Hunt introduced Monsieur S. Rivard, Mayor of Montreal, who spoke as follows : GENTLEMEN: We welcome you with pleasure to our city, and we are proud to find that you have deemed it worthy of your visit. I understand that your association was founded in 1871 with some thirty courageous members, and that so valuable has it been esteemed, and so attractive was it found, that nearly one thousand have now enrolled their names as members and associates. But we must regard your profession as dating back to the stone age and mingling therewith ; how remote that is none of us can tell. Much of civilization is due to the discovery of metals, and the magnitude of our works to their widespread abundance. If you have not accomplished what the alchemists aimed at, which was to turn the ruder materials into gold, you manage, by your subtle skill, to turn stones into gold value. Europe has long since been-dug into and perforated with shafts and galleries in search of metals, and great wealth, and power, and comfort have arisen there-from ; but by an increase of knowledge, and more than European enterprise and energy, America is following rapidly in the race, and by means of natural advantages of a geological character has out-stripped the Old World. We are pleased to see you, gentlemen, as an evidence of the unity of this continent. Maps may have various delineations, but the veins and arteries of commerce and the nerves of science knit all together into one social organism with the same vital functions. We live here on the margin of the world, and can claim but a modest share in. the great works of modern times, but such as we have that can interest you we gladly offer for your observation.' Our Victoria Bridge may he considered appropriate, for without mining engineers to precede the civil and mechanical, no bridge would be there to-day. In truth, the same may be said of all works of metal, and of all that are executed by tools and machinery made of metal. The Mont

Jan 1, 1880

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the high funding level program plan.

Jan 1, 1980

By M Scamardella

The CSA Mine is located at Cobar, New South Wales, where it was in continuous operation from 1966 to the time it went into receivership on 29 January 1998. When it closed it was under the ownership of Golden Shamrock. Glencore International, in conjunction with Mt Lyell Mining, undertook a due diligence study to determine the feasibility to re-open the mine. This envisaged operating CSA Mine as a low-cost, copper concentrate producer under the direction of Cobar Management Pty Ltd (CMPL). The new workforce would consist of contractor trades people in operating functions under the co-ordination of CMPL staff, both on the surface and underground. This was the key to establishing the new culture in the workforce. The orebodies at CSA Mine are steeply dipping with copper-lead-zinc mineralisation in zones of strong alterations in a fine-grained siltstone host sequence. The predominant economic minerals are chalcopyrite, sphalerite and galena. The major gauge minerals are pyrrhotite, pyrite, chlorite, sericite and quartz. Ore for the project is being developed and mined from two high grade copper lenses within the QTS North system. Chalcopyrite occurs in two forms. The first consists of coarse chalcopyrite grains in association with pyrrhotite or pyrite. The second form consists of chalcopyrite grains intergrown with pyrrhotite grains. This form of chalcopyrite is quite rare. It allows electrochemical interactions between grains, resulting in rapid oxidation of the chalcopyrite surface. Physically this ore looks like, and has been mistaken for æpeacock oreÆ, ie bornite, but is infact oxidised chalcopyrite.

Jan 1, 2000

By M. H. Salsbury

This report describes the tunneling at the Leadville drainage tunnel, which was resumed in September 1950 with funds made available in the 1950 appropriation of the Department of the Interior. It brings up to date the account of the first project, carried on from December 1943 to August 1945, published by the Bureau of Mines which supervised both the first and second projects. In this report Leadville mining history, particularly related to drainage efforts, and the possibilities for future mine drainage are discussed briefly. An account of the second project, including a description of the operating cycle, exploratory drilling done as a safety measure, surveying procedures, geology, cost data, and other pertinent information, completes the report.

Jan 1, 1956

By W. Perkins

The Smoky Canyon Mine has recently installed a PROMPTED GAMMA NEUTRON ACTIVATION ANALYSIS (PGNAA) on-line analyzer as part of a long-term advanced process control program. The on-line analyzer was adapted from a continuous dry analyzer and a large on-stream wet analyzer to a compact, multiplexed 3" slurry analyzer. The analyzation feed system utilizes a multiplexer system to accommodate up to fourteen (14) different plant process streams. The corresponding sampling system also provides for dewatering of sample streams too dilute for timely analysis. Key analysis includes, but is not limited to, phosphorus, aluminum, magnesium, calcium, and potassium. This data currently allows plant operations to be manually evaluated and controlled. Future development of a plant-wide supervisory control system will utilize the data for plant operations. This paper discusses the design, installation, and operation of the PGNAA on-line analyzer at the Smoky Canyon Mine.

Jan 1, 1996

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954