Search Documents

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By F. Dinter, S. A. C. Hockaday, Q. G. Reynolds

The thermal decomposition of carbonate minerals as pre-treatment before smelting reduces the energy requirement for smelting. It can also make the combustion of fossil fuels for heating unnecassary. Thermal decomposition may become important in reducing greenhouse gas emissions when producing ferromanganese alloys while simultaneously reducing electrical energy demand during smelting. A kinetic reaction rate model for the thermal decomposition of manganese ores is presented, based on published reaction rate kinetics for the decomposition of manganese oxides and calcium carbonate. The model was validated against thermogravimetric data for two carbonaceous manganese ore samples and one ferruginous manganese ore sample. The reaction rate model shows that carbonate minerals in the manganese ores are decomposed at temperatures above 900 °C while pyrolusite is decomposed at temperatures from 450 °C to 500 °C. Mn2O3 decomposes rapidly at 550 °C. Braunite decomposition at temperatures below 1000 °C was negligible. The presence of organic carbon in the samples led to further reduction of the samples during thermal treatment.

Aug 3, 2023

By Paul Lynch

"Since being reported to the 2012 UMI in Shanghai, the Cook Islands has been steadily developing for the commencement of it Seabed Minerals sector in its large Exclusive Economic Zone which contain a vast and unique Manganese Nodule resource, estimated at 10 billion tonnes1. At the 2013 UMI in Brazil, it was reported that the Seabed Minerals Act had commenced and all the necessary complex Technical aspects of this developmental work was being undertaken. At the 2014 UMI in Portugal, full details of the final developments leading to the opening of the Tender of Exploration Blocks in the Cook Islands EEZ will be presented in a brief but comprehensive method, using Poster displays, Powerpoint and active Website interaction. This will show the drafted Regulations, prepared on best international standards, to address both Licencing and Environmental requirements, to give clarity and security to the Resources Owner, industry and stakeholders. This work in being coordinated by the Cook Islands Seabed Minerals Authority, with the valuable collaboration of many international, regional and national stakeholders, including the Cook Islands NGOs, Marine Resources, Marine Park and National Environment Service."

Sep 1, 2014

By G. W. Birge

Carbonizing properties of the principal coalbeds of Elk, Clarion, Jefferson, Clearfield, and Centre Counties, Pa,, are described in this Bureau of Mines report, Twenty-six samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, and Brookville beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AM) method, and yields of products and physical properties of cokes were determined. Expansion or contraction of the majority of the samples was measured in the Bureau of Mines sole-heated oven. Chemical analyses, agglutinating values, and free-swelling indexes are given for all samples. In this area the coals generally are characterized by high sulfur and moderately high ash content, and their suitability for metallurgical use would depend largely upon satisfactory cleaning. The samples from Elk, Clarion, and Jefferson Counties were high-volatile A bituminous In rank, whereas, most samples from Clearfield County and all those from Centre County were of medium-volatile rank. Coals from Clarion County had dry, mineral- matter-free fixed-carbon contents ranging from 56.5 to 60.3 percent and were weakly coking. With the exception of two samples which contained excessive ash, the medium-volatile coals of Clearfield and Centre Counties were strongly coking and, as indicated by sole-oven expansion results, would require blending with lower rank coal to avoid oven damage.

Jan 1, 1963

By James Pile

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan's geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro¬active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

Jan 1, 2003

By M. A. Georgiana

The Emerald Mine No. 1, located in southwestern Pennsylvania is presently owned and operated by Cyprus Minerals of Englewood, Colorado. High volatile bituminous coal is produced from the Pittsburgh No. 8 seam by both longwall and continuous mining methods. The coal is then mechanically cleaned on site utilizing a combination of heavy media separation and froth flotation methods prior to shipment to both the metallurgical and steam coal markets. The Emerald Mine is presently producing 2.8 million raw tons per year, while liberating approximately 6.5 million ft per day of methane. In light of the methane liberation rate, ventilation requirements have been significant and have always received utmost priority and consideration. Figure 1 shows the locations of the current and proposed shafts. Emerald utilizes two Joy (Model M120-58-880) axial vane fans on shafts No. 1, No. 2R, No. 3R. (one operational, one stand-by) The use of computer simulation of various ventilation networks was initially employed during the design stages (1975-1977) and has been utilized through the present. Obviously, the initial planning, under the ownership of Lykes Resources, was strictly theoretical. All the quantities were proposed and the resistances were based on prior simulations of other mines and mathematical formulas. However, once the mine was moderately developed, actual values were recorded and utilized. This procedure consists of: a) layout pressure and quantity points b) measure all air quantities where an air course splits

Jan 1, 1986

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

By J. A. Maree

After the South Deep complex was purchased by Goldfields in 2006a re-feasibility study was done and the life of mine (LOM) was extended to 52 years. This also implied that the mine?s infrastructure would have to be enhanced. One of the changes was the proposal of five new main orepass systems to be excavated before the mine reaches full production in 2013. Excavations started to show signs of scaling, and in some cases, whole new excavations were lost. This particular area was exposed to very high stresses and the geology was prone to body delimination rendering the relevant areas unstable. This paper investigates the conditions at the location of one of the proposed orepass systems, and the best possible orientation was suggested to ensure that the orepass system would be stable and have a practical life. It was, however, found that the fourth leg of the orepass system would require further support to be classified as stable by the chief rock engineer and the section geologist of South Deep. Several support methods and orepass system linings would then be analysed and evaluated to give calculated recommendations on how to productively and practically support an orepass system. Keywords Main orepass system, stresses, body delamination, impact and abrasion, rock support, concrete lining.

Jan 1, 2011

By W. R. Matizamhuka

"The consolidation of nano-sized composite materials presents a challenge using conventional hot pressing methods. Spark plasma sintering (SPS) technology has shown great promise in the successful sintering of nanoreinforced composite materials. This qualitative review seeks to impart knowledge gathered, and progress made over the years on the consolidation of nanocomposite materials using SPS technology. The review is aimed at introducing this technology to the South African science and engineering community. Emphasis is on improving the mechanical properties of structural ceramic nanocomposite materials, which over the years have shown great promise in a wide range of applications, including transport, energy, mining, and the environment. Although success has been achieved within the laboratory for research purposes, there are still great opportunities to commercialize the technology for the production of larger components with more complex shapes.IntroductionSince the pioneering work of Niihara and Nakahira (1991) over a decade ago there have been extensive attempts to harness the potential of nanostructural metals, ceramics, and composites in a number of applications (Niihara and Nakahira, 1991; Selaho et al., 1997; Sekino and Niihara, 1995; Khalil, 2012; Aalund, 2008). It is generally realized that reducing the grain size of materials to nanoscale offers a significant improvement in properties. Attempts to synthesize nanostructured compacts by conventional sintering methods have not succeeded owing to the uncontrollable high rates of grain growth driven by long dwelling times at the sintering temperatures and large powder surface areas (Sergueeva et al., 2009; Gua, Khora, and Chieng, 2004; Tang et al., 2009). Following the development of spark plasma sintering (SPS) technology, it is now possible to process nanocrystalline materials with controlled grain growth. SPS, also referred to as the field-assisted sintering technique (FAST) or pulsed electric current sintering (PECS), was developed with the aim of improving on the well-established hot pressing (HP) technology (Kessel and Hennicke, 2007;"

Jan 1, 2016

By U. C. Galimidi, J. M. Stewart, A. J. Van Rensburg

The effect of body movement on convective heat transfer from a man performing a block-stepping task was investigated experimentally by direct measurements of convective heat transfer. A series of experiments was conducted in which a nude man was required to stand at rest or to block step at 12 and 24 steps per minute. Wind speed, which was kept constant during each experiment, spanned the range 0,5 to 3,5 m/so Air temperature was kept constant at 43 °C in all the experiments. The results showed conclusively that the convective heat-transfer coefficient depends on the stepping rate. The effect of body motion can be regarded as being equivalent to an increase in the velocity of the free stream. The equivalent increase in air speed was found to be 0,36 and 0,77 m/s for 12 and 24 steps per minute respectively. Data from various sources, including the present study, indicate that wind speed should be increased by about 0,30,0,55, and 0,80 m/s to account for low, moderate, and vigorous body movements respectively. These findings are of direct relevance to the practical assessment of heat stress.

Jan 1, 1979

By E. A. Gyawu, L. L. Eng, M. Fikru, K. Awuah-Offei

Investors and other stakeholders are increasingly concerned about the quality and quantity of sustainability disclosures as well as the extent to which such disclosures correlate with sustainability practices of mining firms. This is because disclosure policies vary widely across firms in terms of extensiveness, materiality, and disclosed topic. In this paper, we conduct a preliminary examination of the relationship between sustainability performance and disclosure. We use sustainability performance indicators such as water and energy use and the Sustainability Accounting Standards Board’s (SASB’s) standards to evaluate disclosures. Our preliminary results show that some measures of sustainability performance (energy use) are negatively correlated to the amount and quality of disclosures while others (water use) are not. Thus, investors should not judge sustainability performance based solely on the amount and quality of sustainability disclosures. In addition, our results suggest that firm size and ownership as well as institutional membership could impact the strength of correlations between disclosure policy and sustainability performance

Mar 2, 2022

By Kenneth E. Gray

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By B. T. Brady

Rock mechanics, like all engineering disciplines, must have a theoretical foundation. The subject of this chapter is the formulation of analytical methods that may aid in the rational design and determination of the stability of engineering structures in competent brittle rock materials. By an engineering structure in rock, we mean any (1) excavated sub- surface opening, (2) open surface structure, or (3) system of openings in rock that is virtually self-supporting-that is, not requiring artificial systems to carry structural stresses.

Jan 1, 1970

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

By J. B. Dilworth

The purpose of this paper is, first, to give a general account of a little-known coal-district of SE. Kentucky, its topography, drainage, and mineral resourcee, for those who may be interested in its economic development; and secondly, so to describe the geologic features of the field as to furnish available data to those engaged on the broader problems of Appalachian coal-geology. The data from which the major portion of the paper has been prepared were obtained, in professional investigations for private individuals and corporations, within the last decade. The area under review, defined by a heavy line on the map, Fig. 1, lies between Little Black and Pine mountains, and extends from Harlan on the west to a N-S. line crossing Looney creek 3 miles from its mouth on the east. This area can be divided for description into a Western and an Eastern Division. The character of investigatioil pursued in the Western Division, below Fugitt creek, was very different from that employed in the Eastern. In the former, only a rapid reconnois-sance was attempted: such coal-openings as had been made by prospectors or by citizens in obtaining fuel were visited, their

Jan 1, 1913

By C. M. McCulloch

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas con-tent of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and des orbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By Benjamin Tillson

To MOST mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount f drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be so handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau f Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 5, 1921

By Benj. F. Tillson

To most mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount of drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be SO handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau of Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 1, 1922

By S. B. Patton, T. Novak

To fully utilize a ventilation simulator as a planning and production tool, the network database must keep pace with mining progress. By using AutoCAD's™ attribute-definition function, the branch data and node coordinates can be stored as part of the branch-diagram file and updated with the drawing. Attributes are drawing entities that contain text which can he extracted in a standard spreadsheet format or as an ASCII text file. The data can be subsequently loaded into a ventilation simulator. This paper presents the methodology for using AutoCAD's™ attribute feature in a ventilation simulation format.

Jan 1, 1995

By S Bouzalakos, W Timms, H Malli

Combining ultramafic mine tailings and acidic mine drainage via mineral carbonation to sequester carbon dioxide, presents an opportunity to minimise waste on mine sites. Low pH mine water with trace element concentrations can be effectively treated by high magnesium mine tailings, a useful source of finely ground reactive matrix. By using milled tailings for mineral carbonation, there are negligible energy requirements for communition of ore rocks to reduce particle size. This study aimed to assess the technical applicability of reacting ultramafic tailings and acidic mine water through mineral carbonation technology in the mining industry. Dissolution has been identified as the rate limiting stage in mineral carbonation; hence the study focused on identifying optimal dissolution conditions. Ultramafic tailings (particle size <100 µm) derived from serpentinite ore, were reacted with a typical mine water that was synthesised in the laboratory. Through variances in the solid to liquid ratios and temperature of dissolution, a maximum five per cent magnesium dissolution efficiency was reached at 50 g/L and 100°C. The acidic mine water was neutralised (from pH <2 to pH ~6) and iron, copper and zinc ion concentrations reduced significantly during the formation of solid precipitates. Carbonation was undertaken by injecting carbon dioxide into the magnesium-rich solution to form stable carbonates. The experimental work demonstrated proof of concept; however, dissolution efficiency and carbon dioxide sequestration was low, indicating that further research would be required before larger scale implementation.CITATION:Malli, H, Bouzalakos, S and Timms, W, 2015. Ultramafic mine tailings to treat acidic mine water and lock away carbon through mineral carbonation, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 133–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015