Search Documents

By R. P. Abendroth

The hydrogen-water vapor ratio at which Fe-Cr alloy, chromium oxide, andiron chromite coexist in equilibrium was determined between 900" and 1200°C. A thermogravimetric method was used to determine equilibrium conditions. The results fit a straight-line relationship in the temperature region studied, and are given by Reduction experiments were also performed to confirm the results of the equilibrium investigation. ThE oxygen pressures at which Fe-Cr alloy, chromium oxide, and iron chromite coexist in equilibrium have been previously determined by Boericke and angert,' Morozov and Novokharski,' and Katsura and uan. Only one determination (at 1300°C) was made by Katsura and Muan, but it agrees with the results of orozov and Novokharski. The results of Boericke and Bangert, however, differ appreciably from the results of these investigators. Previous studies have assumed that the equilibrium metallic phase is pure iron, but Dahl and Van vlack have shown that the iron contains from about 1 wt pct Cr at 1000°C to over 2 wt pct above 1300°C. The chromium oxide also contains a small amount of iron in solid solution. In the present study, hydrogen-water vapor mixtures were equilibrated with the condensed phases, using a therrnogravimetric method to determine equilibrium conditions. The reaction can be written EXPERIMENTAL General Procedure. The starting material was a sintered pellet of Fe2O3-Cr2O3 solid solution with a hole in the center, and was placed on a fused silica hook. This assembly was raised into the preheated hot zone of the furnace in a helium atmosphere, hooked onto a fused silica hangdown suspended from one arm of an Ainsworth Model RV-AU-1 recording balance, and the starting weight determined. A flowing hydrogen-water vapor atmosphere was then exchanged for the helium by evacuation, and the sample reduced until the weight loss indicated the sample composition to be in the alloy-Cr2O3-chromite field. The tem- perature was adjusted incrementally until constant sample weight was achieved for several hours, to within 0.02 mg. A hydrogen-water vapor atmosphere of different composition was then admitted, and the same procedure carried out. At the end of a series of determinations, the sample was examined by X-ray diffraction to verify the presence of the desired phases. Microscopic examination of the silica hook showed no interaction with the sample, nor did it lose any weight. Several criteria were used to insure equilibrium besides constancy of weight. For a given hydrogen-water vapor composition, equilibrium was approached from both oxidizing and reducing sides by varying the furnace temperature slightly. The resulting slow weight loss or gain was observed for several hours. Constant weight could be re-established by returning to the original furnace temperature. The last criterion used was varying the relative amounts of the phases by further reduction or oxidation, and observing any changes in temperature required for constant weight for a given hydrogen-water vapor atmosphere. None were observed. This procedure was essentially the same as approaching the equilibrium from oxidizing and reducing sides, but larger weight excursions were carried out. Sample Preparation. Reagent-grade Fe2O3 and Cr83 powders were mixed in the desired proportions and heated in air at 1250°C for 2 hr. The mixture was re-ground and heated in air overnight at 1250°C. X-ray diffraction showed complete solid-solution formation as a result of this procedure. The solid solution was then pressed into l/2-in.-diam pellets using Carbowax 4000 as a binder. The hole was drilled in the center, and the pellets were sintered 24 hr at 1250°C in air on a bed of Fe2O3-Cr2O3 of the same composition, contained in an alundum boat. After cooling, the pellet surfaces were abraded with 310 paper to remove any surface compositional differences, such as loss of Cr2O3. Chemical analysis of the sintered pellets was 67.16 wt pct CrP3 and 33.02 wt pct Fe203. Atmosphere Generation and Control. The hydrogen-water vapor atmospheres were generated by passing Matheson ultrahigh-purity hydrogen, with no further purification, through two water bubblers contained in a constant-temperature water bath. Since the water-vapor dew points required in this study were below room temperature, the bath was insulated, and was cooled by thermoelectric-immersion devices. The bath temperature was controlled to 0.0l0C. Since rather high flow rates of about 900 ml per min were used through the furnace tube, an independent check of the dew point was made to insure saturation of the hydrogen by the water vapor. Although the dew point could only be determined to within 1/2"C, the determined dew points agreed with the water-bath temper-

Jan 1, 1967

By G. Richard Dreese

Most coal mining states have passed or amended laws restricting strip ruining in the past two years. In light of this and in anticipation of further restrictions by the states and the federal government on strip mining this paper attempts to show the Impact of these new laws on the structure of the coal mining industry in Ohio and specifically on one small stripping firm in Ohio. The implications of the study are applicable to other states under similar circumstances and to other industries which are being caught up in the ecological-economic struggle.

Jan 1, 1973

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By Gerhard Braüner

The report gives a review of the methods of predicting mine subsidence; these methods are used particularly in European coalfields. The methods are subdivided into two groups, based on mathematical expressions either for the trough profile or for the influence of infinitesimal extraction elements. The fundamental relationships common to all methods described herein are the principles of superposition and of equivalent extraction areas. The involved parameters are derived from field observations. For calculating horizontal displacements, their relation to the slope of the subsidence profile is applied. The time-dependent development of the subsidence process is characterized by the empirical "time factor." Modifications for the case of inclined strata are considered. A brief review of experimental and theoretical model investigations is given.

Jan 1, 1973

By Richard Sillitoe

"The paper point out the zinc in the epithermal environmet. The zinc deposits are well known in a variety of sedimentary settings as well as in association with igneous centers, but have attracted little attention in theepithermal environment. Nevertheless, zinc accompanied by gold and silver occurs in several styles of both high- and intermediate-sulfidation epithermal mineralization. However, low-sulfidation deposits are everywhere zinc-poor. High-grade epithermal zinc deposits are hosted by carbonate rocks in transition zones between the HS and IS environments, whereas large tonnages of lowgrade epithermal zinc mineralization of either HS or IS type occur in diatreme breccias or impregnate lacustrine sedimentary rocks around volcanic centers."

Apr 24, 2001

Accurately modeling and predicting long term mill throughput is one of the challenges facing metallurgists, geologists and mine engineers in their quest to consistently deliver accurate life of mine business plans. Batu Hijau has systematically improved long and short term mill throughput predictions since feasibility and commissioning in 1999. This has been achieved through a combination of ongoing improvement to the geology ore hardness and grade characterisation model, drill and blast optimisation and, by application of these data to model mill throughput. Batu Hijau has demonstrated the ability to consistently estimate long term mill throughput within ±2% accuracy. Aside from reliably predicting expected production rates with the existing plant configuration, this predictive ability provides a solid foundation for identifying operating and design criteria for short term grinding circuit optimisation and future expansions. This paper discusses ongoing throughput prediction model development at Batu Hijau based on geo-metallurgical characterisation. Also discussed are tools used for day to day production performance management. This includes on line "Mine to Mill" variable monitoring to improve operations parameter ecision making and performance assessment.

Nov 1, 2011

By F. Wirfiyata

"Accurately modeling and predicting long term mill throughput is one of the challenges facing metallurgists, geologists and mine engineers in their quest to consistently deliver accurate life of mine business plans.Batu Hijau has systematically improved long and short term mill throughput predictions since feasibility and commissioning in 1999. This has been achieved through a combination of ongoing improvement to the geology ore hardness and grade characterisation model, drill and blast optimisation and, by application of these data to model mill throughput.Batu Hijau has demonstrated the ability to consistently estimate long term mill throughput within ±2% accuracy. Aside from reliably predicting expected production rates with the existing plant configuration, this predictive ability provides a solid foundation for identifying operating and design criteria for short term grinding circuit optimisation and future expansions.This paper discusses ongoing throughput prediction model development at Batu Hijau based on geo-metallurgical characterisation. Also discussed are tools used for day to day production performance management. This includes on line ""Mine to Mill"" variable monitoring to improve operations parameter decision making and performance assessment."

Jan 1, 2012

By D. Murray

"The Mine Improvement and New Emergency Response (MINER) Act included the need for improved chemical technologies to address respiratory protective device inadequacies and refuge alternative development. The National Institute for Occupational Safety and Health’s (NIOSH) National Personal Protective Technology Laboratory (NPPTL) invests in research and development to improve the carbon dioxide (CO2) scrubbing technologies built into these mine safety systems. Testing at NIOSH NPPTL is performed using a custom-designed test system containing a chemical reactor and sensors in a constant flow of simulated expired breath to evaluate chemical performance for the scrubber materials. Current testing procedures focus on device duration or capacity, but do not report criteria needed to effectively optimize chemical performance. In this presentation, testing results which identify the chemical performance roles for CO2 scrubber components will be reported, and specific component chemical activities will be linked to both duration and CO2 absorption capacities. Chemical components being evaluated include hydroxyl, superoxides, metal, and amine active sites, distributed in salts, zeolites, metal-organic frameworks, and microporous materials. INTRODUCTION CO2 absorbents and oxygen sources are at the heart of closed circuit breathing air supply systems used in mining escape and rescue operations. CO2 absorbent technology was first developed for diving rebreathers and has been in use for over a century. Typically these devices include a soda lime formulation of pellets in the 8-12 mesh range. Larger 4-8 mesh particles are used in medical grade “low-flow” applications, since these particles present a lower flow resistance regime more amenable for use with resting individuals. Potassium superoxide and lithium hydroxide formulations are also used, where in each case the formulations involve bulk solid pellets or materials affixed to surfaces. CO2 capture technologies are now under intensive study in the energy and automotive industries, where the pursuit of optimal combustion processes has led to the development of new materials to capture, convert and store CO2, oxygen and carbon monoxide gases. Recent advances in nano-structured and high surface area catalysis have produced novel materials demonstrating chemical performance improvements in these industries, and these improvements may now also be adapted to enhance chemical efficiency and performance in escape and rescue devices. Higher surface area materials offer promise for improving the efficiency, or decreasing the burdens associated with the use of closed circuit respiratory protective devices containing CO2 absorbents. Novel chemicals that display advantages in chemical performance or decreased burden will be examined for inclusion in developing systems such as the next-generation closed-circuit mining escape respirator or refuge alternatives."

Jan 1, 2018

By R. J. Durrheim

The DEEPMINE Collaborative Research Programme was established to create the technological and human resources platform that would make it possible to mine gold safely and profitably at depths of 3 to 5 km. The DEEPMINE Programme has four goals: to acquire knowledge of and develop appropriate technology for new ultra-deep level mines, to stimulate education and training, to establish a culture of innovation, and to encourage rapid technology transfer and implementation. The research programme was launched in July1998 and will be completed in March 2002, with the final year focusing on the transfer of knowledge to the industrial partners. DEEPMINE represents a new model for conducting mining research: it is driven by industry needs; emphasizes collaboration between industrial partners, research organizations and tertiary education institutions; and has a novel joint-funding mechanism. DEEPMINE has employed a range of vehicles to transfer knowledge to its industrial partners. Novel aspects include: (a) electronic publication of Summary Reports and Guideline Handbooks that seek to consolidate the huge body of knowledge comprehensively and concisely, (b) a series of DEEPMINE Schools designed to enable industry practitioners to apply the knowledge to their current work situation, and (c) Consultancy Reviews, where DEEPMINE specialists seek to apply knowledge to specific real problems on mines.

Jan 1, 2002

By J. S. Ll. Leach, L. R. Rubin, M. B. Bever

The energies of formation of ordered and disordered solid solutions of composition CusAu and the energy of ordering in this alloy were determined by tin solution calorimetry. The degree of order was measured by X-ray diffraction and electrical resistance and microhardness measurements were made on ordered and disordered specimens. AMONG the phenomena associated with the order-disorder transformation of a solid solution, the change in internal energy is of special interest because of the part it plays in the various theories of ordering. Published values for the decrease in internal energy accompanying the formation of a superlattice from a disordered solid solution of composition CuAu range from —370 to —2260 cal per gram-atom. Some of these values represent calculations based on theory and others are the results of experimental measurements. The distinction between the change in internal energy, AE, and the change in enthalpy, AH, can here be neglected, because they are approximately equal for solid-state reactions at normal pressure. An analysis of ordering by Bragg and Williams' predicts an energy change of —605 cal per gram-atom for the formation of a superlattice in the alloy Cuau from a completely random solution. Peierls" application to Cuau of Bethe'sb earest-neighbor theory yields —560 cal per gram-atom for the formation of a superlattice from a matrix which initially contains short-range order. Cowley' extended the nearest-neighbor approach to include as many as five shells of neighbors; on this basis a change in energy of —500 cal per gram-atom is expected. Eguchi," using a quantum-mechanical treatment, calculated a value of —2260 cal per gram-atom for the difference in the energy of completely disordered and completely ordered Cu,Au. Sykes and Jones- eated a completely ordered alloy and measured its heat capacity as a function of temperature. This measured heat capacity agrees closely with the corresponding value found by the Kopp-Neumann (or mixture) rule up to about 250°C and above this temperature exceeds it, especially near the critical temperature for ordering. The difference between the integrals with respect to temperature of the observed and the Kopp-Neumann heat capacities was considered to be the energy of ordering. By this method Sykes and Jones found a value of —530 cal per gram-atom. This value is not adjusted for the short-range order remaining above the critical temperature. The pres- ence of such short-range order is suggested by the difference between the measured heat capacity and the extrapolated Kopp-Neumann heat capacity immediately above the critical temperature. Values reported by Weibke and von Quadt' and by Hirabayashi, Nagasaki, and Maniwaa were obtained in the course of investigations primarily aimed at other objectives. Weibke and von Quadt measured the temperature coefficient of the electromotive force of a Cu-CuAu cell. They obtained a value of —1010 cal per gram-atom for the heat of formation of the alloy at 500°C, at which temperature there is no long-range order. They also obtained —1380 cal per gram-atom as the heat of formation of the ordered alloy at 370°C. Considering the heat of formation of the disordered alloy to be independent of temperature, they estimated the energy of ordering at 370°C as —370 cal per gram-atom. At this temperature long-range order is incomplete and the degree of order changes rapidly with temperature. Hirabayashi, Nagasaki, and Maniwa," using an annealing calorimeter, investigated an alloy containing 23.4 rather than 25.0 atomic pct Au and thus could not obtain complete order. Thelr value of the energy of ordering was —490 cal per gram-atom. Orianis has recently investigated the Au-Cu system by the galvanic emf technique. He reports values for the heats of formation of Cu-Au alloys, from which the heat of formation at 427 OC of an alloy of composition CuAu may be found by interpolation. This value is —1080 cal per gram-atom. In the work here reported, disordered and ordered alloys of composition CuAu and corresponding mixtures of gold and copper were dissolved in liquid tin and the heat effects measured. These heat effects are small, since the dissolution of gold in tin is exothermic and the dissolution of copper is endothermic. The method, therefore, yields fairly precise values of the heats of formation of disordered and ordered alloys and of the energy of ordering. Experimental Procedure The calorimeter consisted of a long-necked Dewar flask immersed in a constant temperature salt bath and has been described by Ticknor and Bever." The chief changes in this equipment were an improvement in vacuum and the replacement of the mercury thermoregulator by a resistance thermometer control circuit. The solvent, which was maintained at a constant temperature near 350°C, consisted of 500 grams of 99.99 pct pure tin. The solute samples were mixtures of gold and copper in the proportion corresponding to the composition Cu,Au or solid solutions

Jan 1, 1956

By AIME AIME

A PAPER prepared by James A. Adams, development engineer of the fitline & Smelter Supply Co., and presented at the last Annual Meeting of the A.I.M.E. in New York City, de- scribed a new automatic pulp density controller which has had a most favorable reception. Manual control has until now been the universal practice in spite of its shortcomings; samples of pulp for density determination were often improperly taken, and only at the operator's convenience, so that the trend in density changes was frequently missed, and the grinding circuit al- lowed to operate under something less than the most efficient conditions.

Jan 1, 1940

By E. Machaka, A. Cornah

"Mineral resources are typically informed by multiple data sources of varying reliability throughout a mining project life cycle. Abundant data which are imprecise or biased or both (‘secondary data’) are often excluded from mineral resource estimations (the ‘base case’) under an intuitive, but usually untested, assumption that this data may reduce the estimation precision, bias the estimate, or both.This paper demonstrates that the assumption is often wasteful and realized only if the secondary data are naively integrated into the estimation. A number of specialized geostatistical tools are available to extract maximum value from secondary information which are imprecise or biased or both; this paper evaluates cokriging (CK), multicollocated cokriging (MCCK), and ordinary kriging with variance of measurement error (OKVME).Where abundant imprecise but unbiased secondary data are available, integration using OKVME is recommended. This re-appropriates kriging weights from less precise to more precise data locations, improving the estimation precision compared to the base case and to Ordinary Kriging (OK) of a pooled data-set. If abundant secondary data are biased and imprecise, integration through CK is recommended as the biased data are zero-sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case."

Jan 1, 2015

By García B., Wolff E.

In Colombia, northeast of Antioquia, there is a gold deposit that has produced continuously since the middle of the XIX century, located within mining title RPP-140, property of Gran Colombia Gold Segovia (GCGS) since 2010. Mining materials are taken to the “María Dama” Processing Plant where 1500 tonnes of materials are processed daily. Before 2010, the previous owner of the mining title processed about 600 tpd and directly discharged almost all tailings, given that they had no capacity to put them into final deposits. El Chocho was conceived as a final tailings deposit to store the pulp produced by the processing plant; it was divided into two phases with two dams (upper dam and lower dam) given that the presence of illegal miners at the lower phase impeded a single dam design. A squatter impeded construction of the upper dam; so afterwards, starting at the higher end was necessary (owned by GCGS), building dam 1B to store tailings in pulp; after the squatter returned the lands to the owner (GCGS), construction of tailings dam 1A was required and thus complete construction of dam 1C or the upper dam. While all of this was happening, GCGS decided to acquire a 1500 tpd filter press which currently dehydrates tailings in order to take them to the valley controlled by dam 1A. Construction of dam 1A was designed following the containment wall model, made with geotextile tubes. These improvements generated reduced pressure on renewable natural resources because water is recirculated and less fresh water contributions are required; less pressure is placed on soil, flora and fauna because the area intervened for tailings storage will have a higher storage capacity and, as such, a longer useful life.

Jun 17, 2024

The necessary funds have been provided for the award in 1915 of three prizes, respectively of $50, $30, and $20, for the best essays, or other papers, submitted in competition by Junior Members and Members of Affiliated Student Societies. The following rules for the competition are therefore established in accordance with the instructions of the Board of Directors May 22, 1914: (1) A competitor for the President's Prizes must be, at the time of submitting his essay, either a Junior Member or a Member of an Affiliated Student Society of this Institute.

Jan 1, 1917

By M. J. Soria-Aguilar, F. R. Carrillo-Pedroza, S. Preciado-Nuñez

"Dust originated from the Iron Blast Furnace (BF) and the Basic Oxygen Furnace (BOF) containing alkalis and zinc are not completely recycled because due affects the process efficiency. These types of dust represents an economical lost as a consequence of values contents of iron and carbon. Several processes in aqueous media have been developed to treat the steelmaking dust. This work presents a laboratory study for reduce zinc and alkali containing in BF and BOF dust, using different acid and alkaline solutions and oxidants as ozone. The results obtained show that the elimination of zinc and alkalis can vary from 5 % to 80 % depending on the treatment conditions (the solution, the oxidant and the temperature). The dust obtained from this treatment can to be recycling to the steelmaking processes to recovery iron and carbon values.IntroductionEach one of the steel making industry processes generate several sub-products and residues containing useful units of iron, carbon and other elements that are or could be recycled to the productive process. Some of those sub products are the dust from the gas cleaning system of the blast furnace and the dust from BOF reductive process; such dusts are sent to the sedimentary lagoons. The dust represent a lost of 2 % of the total iron and coal mineral’s content feed to the process.The typical iron, carbon and zinc content of the blast furnace dust is approximately 40, 24 and 0.3 % and the content of the BOF dust are 50, 15 and 0.9 % weight respectively, with physics - chemical characteristics that became them susceptible to be agglomerated and feed to the blast furnace. But the high content of zinc does not allow recycling it into the process. At the blast furnace the presence of zinc propitiate the formation of film in the furnace wall; these elements are vaporized in the low section of the cube of the furnace and they are dragged by the gases to the top and condensed again at the cube. Part of these condensed materials strongly adheres to the furnace cover harming it and reducing the empty space of that section, causing eventually a severe perturbation of the ascendant gas flux [1]."

Jan 1, 2008

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By Drew M. Kurtz, Jeff L. Rai, Sara F. Frailey, Mohammad Ayub Iqbal

"This paper presents the foundation changes made for a five-span bridge over the Lehigh River constructed as a design-build project. During excavation within the cofferdam at Pier 2 for the construction of a spread footing to bear on rock, it proved extremely difficult to control the water entering the excavation as the sheet pile tips were variable due to the bedrock pinnacles and a weathered rock zone above the top of rock allowing water to pass below the sheeting. Water also entered from the bottom of the excavation, possibly due to the presence of solution openings within the dolomite bedrock. After repeated failures to achieve subgrade elevation and maintain a dry excavation, a design change to drilled shafts was made. Additional borings were performed for each of the shaft locations to explore the area underlain by karstic dolomite rock. A seal consisting of tremie concrete with adequate weight was placed to counter the differential head of water and the three drilled shafts (with minimum 25 feet [7.62 meter] rock sockets) were installed. A detailed construction sequence was followed and advanced quality control testing was performed. The construction of Pier 2 was completed successfully.1. INTRODUCTIONThis paper presents the description of the design change made from spread footing to drilled shafts as a result of site conditions encountered during the excavation for the spread footing for a bridge pier in the Lehigh River in Allentown, Pennsylvania. The bridge is located in an area underlain with dolomite rock, presenting karstic conditions including irregular top of rock and solution openings that provided high hydraulic conductivity below the top of rock. Also, the presence of a zone of weathered rock and pinnacle rock prevented the advancement of sheet piles when constructing the cofferdam. Thus, the difficulties of advancing the excavation to the desired spread footing level resulted in the design change to drilled shafts during construction. Since the project was Design-Build, the design could be changed by a collaborative process through the efforts of the Contractor, its geotechnical and structural engineers, and the State's (owner's) geotechnical and structural engineers and construction management staff."

Jan 1, 2016

By Michael S. Moats, John Bailey Fletcher

The performance of grinding media can be misrepresented in marked ball wear tests due to galvanic interactions between dissimilar media. The possible galvanic interaction of media materials during marked ball wear tests has not been adequately explored. Corrosion rates and potentials of modern high carbon steel and high chromium white iron grinding media materials were measured using electrochemical testing as a function of pH and chloride content in a simulated mill water. The results replicate previous research with the high chromium white iron sample being more noble (higher corrosion potential) and corrosion resistant (small corrosion current) than high carbon steel. Using the experimental data and corrosion theory, the effects of galvanic coupling on corrosion rates were calculated to examine what could happen during a marked ball wear test or when a mixed media charge is present. This analysis indicates that high carbon steel can cathodically protect high chromium white iron leading to significant decreases in the corrosion rate (up to 99%) of this material during marked ball wear tests. The magnitude of the protection is a function of the pH of the mill water.

Dec 21, 2022