Search Documents

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By Jeff Ardron

Unlike the first predicted deep-sea mining (DSM) boom 35 years, the public response to the re-emergent possibility of DSM is this time round is not entirely optimistic, with serious economic, social, and environmental concerns being voiced. In the intervening years, the troubling notion of the ‘resource curse’ has been popularized, whereby the economies of developing nations rich in natural resources (agriculture, minerals, and fuels), paradoxically appear to fare more poorly than their brethren who have fewer such resources. There have been a variety of explanations and counter-arguments regarding why the resource curse occurs, including how it can be ‘escaped’, and even some disagreement on whether it in fact does occur. Nevertheless, many commentators appear to agree that that the quality of governance is strongly implicated in the socioeconomic success, or failure, of these resource-dependent nations, and could indeed be the deciding factor. Unlike nations with diversified economies, the majority of the income from natural resource economies, in the form of royalties and rents, flows through national government; hence, good governance and fiscal management is of particular concern.

Sep 1, 2014

By Telésforo Márquez, Jose Marquez

"El proceso Isasmelt al ser una tecnología con poco tiempo de operación presentó problemas operativos no observados en otros hornos Isasmelt del mundo debido a su mayor dimensión, (Altura 15.6 y diámetro 5.5 m) que a lo largo del tiempo se han ido corrigiendo en base a pruebas y posteriormente cambios, en especial en el diseño de lanza, caldero que recibe los gases/polvo, ladrillo refractario, controles operativos y de proceso. El presente trabajo recopila toda esta información y trabajos realizados para alcanzar una alta performance operativa, que continua en proceso de mayor optimización, ya que el proceso de mejora continua nunca se detiene. "

Sep 1, 2017

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By L. B. Berger

"Additions to List Published in Information Circular 7444 NEW APPROVALSThe following respiratory protective devices have been approved by the United States Department of the Interior, Bureau of Mines, since Information Circular 7444 was issued (March 1948):Gas Masks Approved Under Schedules 14, 14A, 14B) 11+D, and 14E Type N: Universal Gas MasksUniversal gas masks with filters that afford respiratory protection against smoke from ordinary fires and limited respiratory protection against dusts, fumes, mists, and fogs but do not afford respiratory protection against the toxic smokes of warfare.Willson WUG-Nl universal gas mask. Approval BM-1443, issued to Willson Products, Inc., May 25, 1948.Bullard universal as mask. Extension of approval BM-1443, issued to E. D. Bullard Co., January 12, 19 9.Supplied-air Respirators Approved Under Schedules 19 and 19A Type C: Air-line Respirators4. METCO air-line respirator. Extension of approval BM-1920, issued to Metallizing Engineering Co., Inc., December 8, 1948.Type CE: Abrasive Blasting Helmets, Hoods, or Masks9. M.S.A. abrasive mask. Approval BM-1920, issued to Mine Safety Appliances Co., April 30, 1948."

Apr 1, 1949

By Alan A. Campoli

"Pumpable crib support for longwall gates and ventilation bleeder entries is becoming more prevalent in United States coal mines (Figure 1). The pumpable crib selection and spacing design has been greatly refined by the full-scale testing conducted at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator. The peak load on 24-, 27-, 30-, and 36- inch diameter J-Cribs is, on average, 300, 400, 450, and 650 kips, respectively. Standard J-Cribs have useful deformation of approximately 8 inches. The maximum useful deformation can be extended to 18–20 inches with an exterior reinforcement layer or an interior double wall, for all four J-Crib diameters. J-Crib diameter is primarily limited by a maximum 4.5:1 height-to-diameter aspect ratio. Spacing is controlled by immediate roof stability, anticipated pillar deformation, and roof bolting practice. Approximately 500,000 J-Cribs have been successfully placed in 18 different United States longwall coal mines. The selection and spacing of the J-Crib utilized to date is summarized for each mine.IntroductionLongwall productivity and safety depend on ground stability in gate and ventilation bleeder entries. Numerous support technologies have been developed and employed in United States longwall mines since the 1990s to replace traditional wooden cribbing. Many, if not all, of these technologies have been evaluated at the NIOSH Pittsburgh Research Laboratory since the mid-1990s (Mucho, et al., 1999). The NIOSH Mine Roof Simulator has a 3,000-kip vertical load and 24-inch displacement capacity, which has facilitated in-depth analysis of complex multimaterial support technologies like the pumpable crib. The extreme cost and human exposure risk associated with modern longwall mining prevent the trial and error development that would have been required absent the Mine Roof Simulator research. As a direct result of this research, pumpable cribs are becoming a major component of the standing support industry, providing the peak capacity and extended deformation characteristics necessary for successful gate and bleeder support. Recent research by Zhang, et al. (2012) and others have defined the required performance characteristics."

Jan 1, 2015

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

By O. D. A. Pease, C. D. Young, C. H. Strand

In an effort to employ cast steel of a stronger structure than that found in the annealed steel casting, the possibilities of heat treatment which will increase the strength without materially decreasing the ductulity may be resorted to.

Jan 1, 1915

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

By C. R. Watts

The feasibility of producing composites containing nickel or molybdenum fibers in a beryllium matrix was inrestigated. The composties studied were jabricaled by powder mallurgical techniques. The 1-mil-diarr nickel fibers reacled completely below 900°C, converling the fibers .from nickel to Ni5Be2,. As the /LO/-pressing temperalure as raised above 1110oC, tlie nickel diffused outward from the beryllide fibers. The solid solubility of nickel in beryllium was clboul 20 wt pet at the 1100°C pressing temperature a1 the zone-fiber interface. The 1.5-mil-diam molybdenum fibers slzolred no evidence of reaction and little evidence of diffitsion after pressing at 900°C. Between 1000° and 1050°C pressing conditions, the fibers began lo react , producing 1ayers of MoBe2 and MoBe12, respectively surrounding the molybdenurn core. The struture remained the same at 1100°C with no evidenre of solid solubility of the molybdenum in the berylium or vice versa. In recent years a considerable amount of attention has been devoted to the determination of methods for improving the mechanical properties of materials through the use of fiber or whisker reinforcement. Previous work with metal matrix composites indicates that the study of the chemical compatibility of the fiber and matrix is an area requiring greater understanding. The metal-metal or ceramic-metal interface is frequently subject to chemical reactions that may result in the formation of hard brittle intermetal-lic compounds and/or low melting point eutectic compositions. The reaction products may reduce both the low-temperature and elevated-temperature strength of the composite by weakening the fiber-matrix bond, producing premature failure at the interface. It is well-known that most metal-metal systems and many metal-ceramic systems of interest for structural composites are thermodynamically unstable,'-" particularly at elevated temperatures. If, however, the rate of reaction under the conditions of fabrication is sufficiently low. composites can be fabricated that can be used efficiently for indefinite periods at low temperatures and for short periods at elevated temperatures. This paper presents the results of a series of tests to determine the compatibility of nickel and molybdenum fibers with beryllium at various hot-pressing temperatures. Nickel was selected as a candidate fiber material primarily because the relatively ductile fibers might be useful as crack arresters in applications such as ballistic impact where crack growth can result in catastrophic failure. The high density and the reactivity of nickel were primary factors detracting from its selection as a possible reinforcement. Molybdenum with a modulus of elasticity of 52 Xlo6 psi is one of the few metallic materials having a modulus higher than beryllium (42 X lo6). Its high modulus, coupled with its refractory characteristics, made molybdenum an attractive candidate for a relatively stable fiber reinforcement for beryllium. Its density, being higher than that of nickel and over five times that of beryllium: detracted from its other characteristics. EXPERIMENTAL PROCEDURE The specimens were prepared from beryllium powder with a dispersed phase of fibers by powder metallurgical techniques. P-20 grade powder, Table I, from Berylco was used as the matrix material. Short lengths of 0.001-in.-nominal-diam nickel fibers supplied by the Sigmund Cohn Corp. and 0.0015-in.-nominal-diam molvbdenum fibers obtained from the General Electric Co. were used as the dispersed phase. The composite constituents were combined under an argon atmosphere by mechanically mixing the powders and fibers. The compositions used were nominally 1 vol pct fibers. After mixing. the composites were hot-pressed into a-in.-diam pellets under an argon atmosphere at 900°, 1000". 1050". and 1100°C at a pressure of 6000 psi with no hold time at these temperatures so that a comparison could be made between the resultant microstructure and hot-pressing temperature. The billet was heated at a rate on the order of 30°C per min to the desired temperature and then cooled at a somewhat slower rate. The microstructure obtained should be considered as characteristic of the integrated time-temperature history of the sample, as well as the maximum temperature attained. Upon removal from the hot-pressing dies. the specimens were cut. mounted. and polished by standard procedures. No etchant was used in specimen preparation. Photomicrographs, electron microprobe scans, and electron back-scatter pictures were made. X-ray dif-fractometer patterns were made of several of the specimens. but only the lines for beryllium could be resolved. Specimens for optical and electron microprobe examination were selected partially for the roundness of the cross section. A round cross section was taken to indicate that the body of the fiber was approximately normal to the surface and that therefore effects due to fiber material immediately below the surface could be neglected. RESULTS AND DISCUSSION The microprobe scans indicated that nickel reacted as low as 900°C, converting the entire fiber cross section to NisBe21. Fig. l(a). There was no evidence of further reaction from the optical or the back-scatter pictures, Figs. 2(n) and 3(a).

Jan 1, 1970

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

I had hoped when the time came for me to address this meeting that gold mining would be in a much happier position than we find it to-day.As it is, and because of the demands of national security, we find this great and valuable primary industry relegated to the background and in danger of temporary extinction.These notes refer mainly to gold mining in Western Australia, whence comes the major portion of Australia's production, and their purpose is to record a brief review of the industry immediately prior to the general disorganization that is following the call-up of men from the mines.During this period of reduced production the loss of comparable statistical data will make it impossible to follow the progress of the industry, and, since the period may be long, it occurred to me that information might be derived from an examination of the trend of recent production that would indicate what may be expected of the industry when full production is resumed in the future.Since the revival of gold mining, which started in 1931, most of the old-established mines have reorganized and, in some cases, completely renewed and enlarged their equipment in order to achieve maximum production, and old mines hitherto unpayable have been re-opened and equipped. At the same time large sums have been spent in scientific prospecting and in search for new mines, and it is safe to say that at the end of 1939, when gold production reached its peak, practically every known mine in Western Australia that could be worked profitably was in production.During this period the number of men employed in the industry rose from 5,961 in 1931 to approximately 15,000 in 1939. From the outbreak of war in 1939 to the end of 1941 the output from the mines was maintained at full pressure, maximum tonnage beingrecorded in 1940, although a reduction in the grade of ore treated caused a slight falling off in gold production.During 1941 there was a. fall in both tonnage and grade. The decline in tonnage was due partly to the closing of the Lancefield and Mount Magnet mines, and partly to the shortage of labour brought about by the response of the goldfields to the call for men for the fighting services, the average number of men in the industry in this year being reduced to 12,929.With the entry of the United States into the war in December last and the pooling of the resources of the allied nations, the need for gold as a purchasing medium passed, and with its passing there arose the demand for the transfer of the man-power engaged in gold mining to other fields of industry directly connected with the war effort.There was a ready response by those connected with the industry who...

Jan 1, 1942

By Oscar J. Restrepo

Through reactions in solid form at high temperatures, using iron oxide (Fe3O4) and chromium oxide (Cr2O3) in fixed proportions as precursors, the compound was synthesized with spinel structure type FeCr2O4. For different temperatures synthesis was conducted the characterization of the material obtained through X-ray diffraction (XRD), spectroscopy UV-VIS-NIR, scanning electron microscopy (SEM), energy dispersion analysis of X-ray (EDX) thermal analysis (DTA / TGA) and magnetic susceptibility of alternating current. The changes in the spectra of reflectance changes are related to the phase identified, the degree of crystalline structure, the spatial order of cations and the magnetic behavior obtained.

Jan 1, 2009

By Richard R. Klimpel

INTRODUCTION Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Froth flotation is a physico-chemical process for separating finely ground minerals from their associated gangue material. The process involves chemical treatment of a finely divided (ground) ore in a water pulp to create conditions favorable for the attachment of certain of the mineral particles to air bubbles. The air bubbles then carry the selected minerals, called valuable, to the surface of the pulp to form a stabilized froth which is removed and recovered. The unattached gangue material remains submerged in the pulp and is either discarded or reprocessed. To obtain the adherence of the desired mineral particles to the air bubbles, at least two specific steps must occur: a hydrophobic (water hating) surface film must be formed on the particles to be floated along with a hydrophillic (water wetting) film on all other particles; and a controlled bubble surface tension interface must be maintained, allowing for high particlelbubble collision frequency and efficient attachment or sticking of the particle to the bubble once collision has taken place. In most flotation applications, the above two steps are controlled by chemical flotation reagents. The collector is a chemical reagent which produces the hydrophobic film on the valuable mineral particle and is the primary driving force that initiates the flotation process. The frother is a chemical reagent which influences the collision frequency and attachment efficiency of hydrophobic particles and air bubbles. Thousands of research papers and books have been published on the chemical theory behind sulfide mineral collectors, e.g., Fuerstenau (1962), Fuerstenau (1976), Fuerstenau, et. al. (1985), King (1982), Leja (1982) and Moudgil and Somasundaran (1987), This article will only address and summarize some of the more practical aspects of collector usage. The industrial scale practice of froth flotation in sulfide mineral concentration has changed little since the 1950's. For example, of the approximately 80,000 metric tons of sulfide mineral collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago. A very interesting and informative history of collector development has been given by Crozier (1984). In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920's with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years. As a result of the above environment which makes reagent cost/performance analysis difficult for new reagents, there is a strong tendency for the flotation operation to use, and reagent companies to supply, as cheap as possible raw materials and manufactured products that are quite general in application. In the last 20 years or so, there has been increasing technical effort to tailor make reagents for specific applications, but to date such work has had little commercial impact. It is clearly the hope of this author and others that this situation will change in future years as technology improves and pressure for improved flotation performance intensifies. This article is a condensation of collector usage trends quantified as part of a comprehensive industrially oriented applications program on froth flotation organized by Klimpel and coworkers (1979-1987) and as reported in various countries that participated in the program from 1978-1983. No attempt will be made to provide specific.

Jan 1, 1986

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

By D. H. Platt

Bauxite, the principal source of aluminum, has been mined from deposits in Saline and Pulaski Counties, Ark., since 1899; war needs have greatly stimulated production. Many of the ore deposits are basin-shaped and either outcrop or are covered by a shallow-depth overburden at their peripheries; these are mined by stripping and open-pit methods. When stripping becomes economically impracticable, incline shafts or slopes are sunk on the dips of the deposits, and underground mining is done on the retreat, using a room-and-pillar method.

Jan 1, 1945

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

By T. J. Otto, I. D. Ungerer, G. C. Lindeque, T. J. van Heerden

Anglo American Kumba Iron Ore (Kumba) continues to implement technologies focussed on improving safety and productivity; this forms part of the groups FutureSmart Mining initiative. The paper provides insights into the implementation of three technology solutions that improves the productivity of heavy mining equipment (HME). Enhancements to the short term mine planning (STMP) process, the effective use of a fleet management system (FMS) and the deployment of drones or Remotely Piloted Aircraft Systems (RPAS) are discussed. The implementation of these and other technologies contributed to a 13% and 22% increase in the overall equipment efficiency (OEE) of the primary HME at Kumba’s Sishen and Kolomela mines respectively. Four key success factors (KSF) are highlighted namely that Kumba’s technology implementation drive is a key enabler to the company’s strategy, has a strong focus on value-add, is underpinned by a holistic and integrated implementation approach and is people-centric.

Sep 1, 2021

By M McLean

This paper deals with change strategies on brownfield and greenfield sites in extractive industries. It draws upon contemporary experiences across Australian, Indonesia and Papua New Guinea (PNG). Change strategies can be used when owners of an extractive industry operation want to optimise their resource. This paper draws upon many tried and proven theories and practices, including the findings of the Tavistock Institute (Trist, Emmery, Bamford, Jaques), as well as the concepts of Adult Learning espoused by Malcolm Knowles and is supported by learnings of Australian based management consultants. This paper reviews a range of approaches that have succeeded in the integration of systems, machines and people, with the key corporate objectives of: increasing productivity; decreasing cost; improving on-time delivery performance and achieving long-term survival. Such integration needs to be measured to show the outcomes from the change strategies and the authors have worked within many measurement regimes and metrics but for the most part, found that JaquesÆ set of metrics being æquality, quantity, resources and timeÆ has gained currency across many Australian operations. This paper contends that investing money in machines alone without a commensurate investment into the people side is counter-productive. Further, if there is not an understanding of processes, ie stable and capable, core and support processes, then all that new technologies will do, is to make what is done badly, only quicker. Recent interventions for the most part, have been cognisant of this balanced approach towards change management. The change strategies described are across extractive industry implementations, using a number of tools and techniques drawn from Continuous Improvement and Six SigmaÖ (registered trade and service mark of Motorola Corporation, USA).

Jan 1, 2006