Search Documents

By Takashi Sasaoka

A great deal of coal will be left under the final end-walls in Chinese surface coal mines because of lower slope angle in shoveltruck mining systems and larger mining depths. In traditional surface mining systems, the coal under the end-walls will be buried by the inner dumping site, and these coal resources are generally abandoned. Considering these situations, the application of end-wall mining systems was considered in order to recover the residual coal around the end-wall. This mining system can improve economic benefits by exploiting haulage and ventilation roadways from end-walls and utilizing the existing transportation systems. In order to develop the appropriate pillar design methodology for the end-wall mining system, several empirical formulas and methods were discussed based on the formulas developed so far and the mechanics properties of coal and rocks in the Chinese coal mine. From the results of a series of theoretical and numerical analyses, it can be concluded that the coal pillar width calculated by the Mark- Bieniawski formula may serve as an important reference for pillar design in end-wall mining systems, and the end-wall mining system can increase the coal recovery from residual coal resources around highwall and reduce the effect of underground mining operation on slope stability

Jan 1, 2013

By L. A. Willey

IN 1953, a method for filtering a liquid phase from solid phases while in equilibrium at elevated temperatures was devised at the Alcoa Aluminum Research Laboratories. Since then, it has been applied to the investigation of liquid-solid equilibrium in metallic systems. In application, the method simplifies the centrifuge filt.ration procedure as developed by Scheil and described by Gebhardt Fig. 1 shows a sketch of the filtering apparatus located within a thermal analysis furnace. It consists of a stainless steel filter crucible A, into the bottom of which a porous carbon filter disk B, 1 3/4 in. diam by 1/4 in. thick, is sealed to the shoulder and rim with carbonaceous cement. The base of the filter crucible, machined to an angle, fits into a tapered seat at the mouth of a stainless steel vacuum chamber C. A connecting tube from the vacuum chamber to a vacuum line also serves as a means for supporting the apparatus from the base of the furnace. An alundum crucible D of 25 ml capacity is placed with- in the vacuum chamber below the filter for collecting the filtrate. Two thermocouples E, in stainless steel protection tubes, which extend from 1/16 to in. above the center of the filter, are mounted on the rim of the filter crucible. One thermocouple is used in differential connection with the furnace control thermocouple to regulate rates of heating and cooling. The other serves as a means for recording the temperature of the alloy prior to filtering. A suitable mold coating is used on exposed surfaces of stainless steel parts to guard against attack upon these parts as well as to avoid contamination of the alloy samples. A mold wash prepared from precipitated CaCO, is suitable for aluminum alloys. The porous carbon for the filter disks and the carbonaceous cement, grade 200 (graphite base), were obtained from the National Carbon Co. Porous car-bon, grade Nos. 10 to 60, has been employed. Grade No. 40, however, appeared to give the optimum advantages in operation. In operation, an alloy sample is remelted and heated to about 50°C above its liquidus temperature. At the same time, the filter apparatus is preheated to about the same temperature. The alloy then is cast into the filter crucible.

Jan 1, 1957

By Louise Corriveau

Exploration strategies have traditionally considered felsic gneiss complexes of the Canadian Shield sterile. This paradigm is challenged with the discovery of extensive granulite-facies Cu-Au, Fe oxides-bearing hydrothermal systems in the 1.4 Ga Bondy and 1.5 Ga La Romaine volcano-plutonic complexes of the Grenville Province. Early identification of magnetite-rich units in association with meta-exhalite and pelite-like units was key to targeting the search for mineralization, protolith information and indicators of pre-metamorphic hydrothermal activity during regional surveys of these frontier terrains. Textural evidences for a volcano-plutonic setting were found. There remained, however, numerous impediments to the recognition that the ubiquitous magnetite-laden units and associated aluminous gneiss were hydrothermal in origin. Many metamorphic reactions form magnetite at the amphibolite to granulite facies transition, and hydrothermally-leached rocks resemble metapelite or migmatitic restite, while carbonate alteration zones may look like marble or calc-silicate rock. Non-typical metamorphic mineral assemblages, modes and colours arise when hydrothermally-derived rock types are metamorphosed. These effective markers served as tools for reliable field identification of hydrothermally-altered rocks. In our case-studies, we traced pre-metamorphic hydrothermally-driven Fe-oxide precipitation in association with sericitization, albitization, pyrophyllite alteration, chloritization, and B enrichment by mapping unusually high contents of (1) magnetite or hematite, (2) biotite, (3) albite, (4) sillimanite, (5) orthopyroxene or phlogopite with cordierite, and (6) tourmaline or kornerupine. The unveiled garnetite, tourmalinite, and aluminous gneiss had assemblages that vary according to metamorphic grade and composition. To assess if high mode of Fe-Mg-Al phases resulted from partial melting (restitic residue) or metamorphism of hydrothermal rocks, we compared leucosome mineral assemblages, shape and amount with that expected of in situ partial melting reactions. In both areas there is no compelling evidence for these units to be restites. In contrast, the presence of lapilli in garnet-cordierite-sillimanite gneiss, though extremely rare, constitutes conclusive evidence for extreme pre-metamorphic high-sulphidation alteration of a volcanic protolith, while Fe-oxides or sillimanite-bearing nodules and veins record a less pervasive alteration. Geochemical research on element mobility and mass balance calculations further testified of an hydrothermal origin for these gneisses. The magnetite-rich units, together with calc-silicate rocks, garnetite, hornblendite, albitite among amphibolite, provided effective guides to sites of fluid discharge and led to the discovery of Cu and Cu-Au showings. With the presence of highsulphidation alteration, these features suggest early Cu-Au VHMS-type alteration halos within a predominantly felsic composite volcano-plutonic arc setting for both case-studies. Evidences for subsequent F-driven orthomagmatic fluid activity are also present.

May 1, 2003

By Pedro Ruiz

Dado que los relaves mineros generan un impacto ambiental -en tanto las propiedades físicas, químicas y biológicas de los suelos no son las mismas para el crecimiento y desarrollo de las especies vegetales. En este sentido, el presente texto plantea la fitorremediación como alternativa adecuada para el crecimiento de la vegetación a través de dos técnicas utilizadas en Europa y Estados Unidos de Norteamérica. La fitoextracción y fitoestabilización son utlizadas para la limpieza de suelos contaminados con metales pesados. micorrizas. Así, la aplicación de la tecnología de fitorremediación se presenta como una excelente opción para la descontaminación y restauración de los más de 8,000 relaves abandonados existentes en el Perú.

Aug 1, 2013

By D. F. Botkin, B. H. Sage, W. N. Lacey

Joule-THomson coefficients for two natural gases were determined at pressures up to 600 lb. per sq. in. throughout the temperature interval between 70" and 310°F. From these primary data and available information relating to the isobaric heat capacities of the components at infinite volume, the heat capacities of these gases were computed throughout the above-mentioned range of pressures and temperatures. The enthalpies of the gases were computed as a function of state and the results compared with values obtained by several methods of prediction currently available. Table i .—Composition of Gas Samples Components Gas A Gas B Carbon dioxide................ 0.0090a 0 .042 0 Methane...................... 0.8255 0.8385 Ethane.......................0.0901 0 .0637 Propane....................... 0.0462 0.0374 Isobutane..................... 0.0074 0.0039 n-butane................ ...... 0. 0126 0 .0095 Isopentane.................... 0.0032 0.0016 n-pentane..................... 0.0022 0.0011 Hexanes and Heavier........... 0.003& 0.0023 Experimentally determined Joule-Thom. son coefficients for natural gases afford a satisfactory means of checking the accuracy of prediction of their thermodynamic properties from the behavior of the components in the pure state and in binary mixtures. Relatively small samples of these natural gases were available, together with their analyses, and the Joule-Thomson coeffi- The Joule-Thomson coefficients were determined by measuring the change in temperature resulting from the passage of the gas through a porous thimble with a known pressure difference and under such conditions that the process was substantially isonthalpic. The details of the apparatus employed for this purpose have been described.' It is believed that the changes in temperature and pressure were ascertained with an uncertainty of not more than 0.3 per cent. However, as a result of deviations from steady flow, it is probable that uncertainties as large as 2 per cent may exist in the measured Joule-Thomson coefficient. The gases utilized in this work were taken from high-pressure separators and were dried prior to use by passage over calcium chloride at pressures in excess of 300 lb. per sq. in. The gases were subjected to the conventional fractionation and Orsat analyses. The results are recorded in Table I. The composition is typical of gases from such sources, with the possible exception of the presence of significant quantities of carbon dioxide in each of the samples. The experimental results obtained for the two natural gases are graphically Portrayed in Figs. I and 2. The experimental

Jan 1, 1943

By W. N. Lacey, D. F. Botkin, B. H. Sage

Joule-THomson coefficients for two natural gases were determined at pressures up to 600 lb. per sq. in. throughout the temperature interval between 70" and 310°F. From these primary data and available information relating to the isobaric heat capacities of the components at infinite volume, the heat capacities of these gases were computed throughout the above-mentioned range of pressures and temperatures. The enthalpies of the gases were computed as a function of state and the results compared with values obtained by several methods of prediction currently available. Table i .—Composition of Gas Samples Components Gas A Gas B Carbon dioxide................ 0.0090a 0 .042 0 Methane...................... 0.8255 0.8385 Ethane.......................0.0901 0 .0637 Propane....................... 0.0462 0.0374 Isobutane..................... 0.0074 0.0039 n-butane................ ...... 0. 0126 0 .0095 Isopentane.................... 0.0032 0.0016 n-pentane..................... 0.0022 0.0011 Hexanes and Heavier........... 0.003& 0.0023 Experimentally determined Joule-Thom. son coefficients for natural gases afford a satisfactory means of checking the accuracy of prediction of their thermodynamic properties from the behavior of the components in the pure state and in binary mixtures. Relatively small samples of these natural gases were available, together with their analyses, and the Joule-Thomson coeffi- The Joule-Thomson coefficients were determined by measuring the change in temperature resulting from the passage of the gas through a porous thimble with a known pressure difference and under such conditions that the process was substantially isonthalpic. The details of the apparatus employed for this purpose have been described.' It is believed that the changes in temperature and pressure were ascertained with an uncertainty of not more than 0.3 per cent. However, as a result of deviations from steady flow, it is probable that uncertainties as large as 2 per cent may exist in the measured Joule-Thomson coefficient. The gases utilized in this work were taken from high-pressure separators and were dried prior to use by passage over calcium chloride at pressures in excess of 300 lb. per sq. in. The gases were subjected to the conventional fractionation and Orsat analyses. The results are recorded in Table I. The composition is typical of gases from such sources, with the possible exception of the presence of significant quantities of carbon dioxide in each of the samples. The experimental results obtained for the two natural gases are graphically Portrayed in Figs. I and 2. The experimental

Jan 1, 1943

By Daniel Paulo Santos, João José dos Santos Carvalho, Leonardo Passos Perdigão, Alexandre Santos Tardin, Filipe Sathler, Leonardo Barbosa de Oliveira Mello, Odilon José da Silva, Marcelo Tardin Alves

A estabilidade operacional do alto-forno depende da qualidade de suas matérias-primas, sendo a resistência mecânica do coque após a reação – Coke Strength after Reaction (CSR) um dos principais parâmetros de controle da qualidade do coque para verificar a degradação granulométrica do coque após sua reação com CO2. O desafio das empresas siderúrgicas está em produzir um coque de baixo custo e elevada qualidade com resultados precisos e consistentes para atendimento às especificações requeridas pelo alto-forno. Neste trabalho em particular, utilizando a metodologia Seis Sigma, foi desenvolvido e validado uma equação matemática (modelo de regressão linear múltipla) para previsão do CSR produzido pela coqueria da ArcelorMittal Tubarão, a partir de dados estatísticos correlacionados à parâmetros da mistura de carvão (teor de cinzas totais, enxofre médio e a composição química das cinzas expresso pelo índice de basicidade).

Oct 1, 2019

By Bailey DJ

Loader cut and fill stoping was first used at New Broken Hill Consolidated Limited mine in 1966. The equipment used included single boom pneumatic jumbos for drilling up- holes, diesel loaders for ore removal and diesel utility vehicles for rockbolting and servicing. Since 1966, there have been many modifi- cations and changes both in the equipment and stoping method. Twin boom pneumatic or hy- draulic drilling jumbos have replaced single boom pneumatic jumbos, electric loaders have replaced diesel loaders, diesel forklifts have replaced utility vehicles and "'flatbacking" has superseded uphole stoping. Concurrent with this has been the introduction of cable dowels in stope backs which has enabled loader cut and fill stoping to be used more extensiv- ely than in the past. There are now six loader cut and fill stopes at both mines and this paper traces the evolution of this method outlining the reasons for changes in technique and equipment.

Jan 1, 1982

By Jesse Puller, Ken W. Mills, Owen Salisbury

"An underground coal mine located in New South Wales has a target coal seam located 160-180 m deep directly below a 16-20 m thick conglomerate unit that has been associated with significant periodic weighting events on the longwall face. As part of the investigations to better understand the causes of periodic weighting at the mine, inclinometers capable of measuring horizontal shear movements through the full section of the overburden strata were installed ahead of mining at two locations approximately 1 km apart above the centre of two longwall panels. These inclinometers were monitored as the longwall approached each site. This paper presents the details of the installation, the results of the inclinometer monitoring at both sites, and the insights that these measurements provide for overburden behaviour about longwall panels.Horizontal shear movements were observed to develop on shear horizons that correlate closely across the two sites suggesting a mechanism that is consistent across a large area of the mine. Shear movements were observed to develop on a single horizon near the top of the conglomerate strata that was mobilised almost immediately after initial formation of the longwall goaf at a distance of 425 m ahead of the longwall face. The direction of horizontal movement was consistent with the relief of the major principal horizontal stress. As the longwall face approached each inclinometer, other horizons within the upper part of the overburden strata begin to shear with the upper strata moving toward the approaching goaf more than the lower strata. Within the last 30 m of longwall approach, tilting of the strata associated with the increase in vertical subsidence toward the extracted goaf caused a change in the style of deformation with tilting and reverse shear offsets.INTRODUCTIONLongwall mining is recognised from subsidence monitoring, surface extensometer measurements, and various other observations to cause significant disturbance to the overburden strata directly above the extracted goaf of each longwall panel. Disturbance to the overburden strata beyond the limits of each longwall panel is not so well understood. Subsidence monitoring indicates that horizontal movements beyond the edges of the extracted longwall panel are generally greater in magnitude than vertical subsidence and horizontal movements may extend up to several kilometres from the edge of the panel in some circumstances (Reid 1998, Reid 2001, Hebblewhite et al 2000, Mills 2001, Mills 2014). The mechanics of how these movements are accommodated within the overburden strata is only poorly understood and there are few direct measurements."

Jan 1, 2015

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By S. R. Dunbas, D. C. Jillson, E. A. Anderson

THE present work was undertaken to furnish information, lacking in the literature, on the deformation mechanisms active in pure titanium at room temperature. Since it was started, Rosi, Dube, and Alexander' have indicated that slip can occur in coarse-grained (2 to 6 mm diameter) titanium on the {1010} and {1011} planes and twinning can take place on the {1072}, (1122) and (1151) planes. Liu and Steinberg,' working with titanium flakes produced by fused salt electrolysis, found evidence of twinning on the {1032$, {1121), {1122}, (1123}, and (1154) planes. The crystals used in the present work were substantially longer (up to nearly 2 in. in length) and possibly purer. Production of Large Crystals It was the purpose of this part of the work to provide single crystal or large grain specimens for use in the deformation studies rather than to study the mechanism of crystal growth. Accordingly, all further exploratory studies on methods were abandoned when it was found that cold-rolled bars sealed in vacuo in individual Vycor tubes and given three or more cycles of 4 hr at 1200°C and three to five days at 850°C, gave large grains. Eighteen specimens about 0.2 in. square x 2 in. long yielded 33 useful grains, ranging from Va in. to nearly 2 in. in length, with an agreeably wide range of orientations, Fig. l. The 0.25 in. thick strip from which the starting specimens were cut had been reduced 67 pct on 18 in. diameter rolls from a scalped, hot-forged (959" to 1000°C), arc-melted, iodide titanium ingot. Thc bar was at room temperature, but the rolls were at 200°C. Reductions of about 0.03 in. per pass were used. The bar was cut into four segments, each of which was rolled in a somewhat different manner. No effect on the growth of large grains was noted. The composition of the titanium, determined on turnings from the ingot scalping operations, is given in Table I. The Rockwell A hardness of the ingot was 26. The standard starting specimens, about 1/4x1/4x2 in., were milled on all four sides, hand polished on 280 and 400 mesh emery papers, etched for 3 min in a 50 HF-50 glycerine solution, rinsed, and dried in alcohol and ether just before sealing them in Vycor tubes. The average specimen weight was 7.5 g, and the tube volume was 6.5 cc. A vacuum of less than 1 micron pressure was applied. The specimen tubes were placed in an evacuated Inconel muffle to minimize the danger of collapse of the glass tubes at temperature. In practice the specimens were first heated to 1200 °C for 4 hr and then transferred fairly quickly to an 850°C furnace where they were held for three to five days. This cycle was repeated at least three times before the specimens were cooled, removed from the tubes, lightly polished and etched on one surface for examinstion. Those in which large grains had not developed were resealed in Vycor and returned to the cycling. Satisfactory specimens (about one out of every four cycled) were polished with emery paper on all four side;, then metallographically polished using ctchinz between wheels to remove distorted metal and, finally, given a very light etch to reveal the grain boundaries. This was necessary because the surface was roughened by the sublimation of titanium under high temperature vacuum conditions. Specimens were identified by TiXl numbers using supplementary letters to designate specific grains.

Jan 1, 1954

By Oliver Bowles

In 1943 the Bureau of Mines began a review of trends in consumption and prices of the more important nonmetallic minerals. The first report covering building materials4/ appeared in December of that year. The present paper, which deals with chemical raw materials and fertilizers, is the second of the series. The 34 years from 1910 to 1943, for which statistics are presented herein, comprise periods of uneventful peace, unparalleled prosperity, industrial depression almost to the point of stagnation, and two wars of world proportions.

Jan 1, 1945

By K. Takahashi, G. Dodbiba, T. Fujita, N. Sato, S. Matsuo, K. Okaya

Different materials are used for manufacturing various parts of a cellular phone. Considering that a great number of mobile phones are being discarded every year, it is important to recover these materials and then recycle them in order to save resources. The primary objective of this work is therefore to find and suggest ways on how to recover various materials from discarded cellular phones for recycling. Much effort, for example, has been put in recovering and recycling tin oxide (ITO), a mixture of indium (III) oxide, (UI2O3) and tin(IV) oxide from the discarded liquid crystal displays (LCDs). Here we report a simple and cost-effective process, which includes a HC1 treatment process for altering the structure of the indium (III) compound into a chlorideinduced indium compound, in order to facilitate the vaporization of indium at a relatively low temperature. The experimental results indicated that 96.2 % of indium can be recovered from ITO, when the sample was heated at 973 K for 90 minutes. In addition, some thermodynamic calculations were also carried out in order to better understand the mechanism for chlorideinduced vaporization of indium.

Jan 1, 2011

By Ross W. Whipple

Applying geophysical techniques in potential geothermal areas has received: little attention in the United States, though it is widely used and accepted in New Zealand and Italy. In those countries it has been demonstrated that geophysical surveys can be useful in locating new geothermal areas and in directing test drilling programs. Geophysical studies in a thermal region can provide structural information and, if conditions are right directly; locate subsurface hot waters. They can give indications of sub-alluvial rock types and of the thickness of alluvial cover. In certain cases they can be used to estimate the power potential of a hydrothermal system.

Jan 1, 1963

By M. Hawker, M. Kreuh

The mining and metallurgy industry is known to be of cyclical nature associated with price volatility. As such, some years are quite lucrative and other years require mining companies to tighten their belts. The field is a mix of junior, mid-tier, and major mining companies. One thing that is common to all of them is the time required and the cost to develop a flowsheet in accordance with best practices. Although a long list of factors can impact flowsheet development, this paper will include the impacts of: experienced metallurgical engineers and laboratories, representative samples for high quality and valuable testwork results, and following engineering development stages. The paper also provides typical time frames to complete selected engineering flowsheet development steps.

Jan 1, 2014

By B. M. Davis

Frequently ore reserve studies utilize samples from a series of drilling or other types of sampling campaigns. Sometimes there is a mix of sample types, say for instance, channel samples from underground workings and drill core from surface drilling. Since drilling, sampling, logging, and sample preparation protocols tend to change over time, there is always a question whether the samples give similar results that vary only by chance alone. The problem of comparing the various campaigns is complicated by the presence of spatial relationships among the samples. Geostatistical tests take the spatial correlation into account, but these tests may be complicated and cumbersome to implement. A comparison method based on familiar statistical graphics is presented which accounts for the spatial relationships. It allows comparisons to be made quickly by using simple statistical graphs such as scatterplots and boxplots.

Jan 1, 1996

By E. Siami-Irdemoosa, S. R. Dindarloo

"Discrete event simulation is a stochastic mathematical modeling tool with applications in queuing systems. Many mining operations, both surface and underground, can be simulated in the context of queuing theory , for example open pit loading and haulage operation, underground level and vertical transportation, and mineral processing circuits. A computer simulation model of the operation is an invaluable tool to study both the system’s dynamics and conducting sensitivity analysis on different effective elements on system performance. In this paper, merits of discrete event simulation in decision making in mining engineering is discussed. Moreover, a stochastic simulation framework for selection and sizing of shovels and dump trucks in surface mining is presented to elaborate one example for applicability of the method in mining operations. INTRODUCTION Mathematical modeling is a valuable tool in design, optimization, and decision making in both surface and underground mining operations. Several researchers have tried to study different aspects of mining operations using a wide range of mathematical techniques such as linear programming[1], analytical hierarchy process [2], non-linear programming[3], genetic algorithms[4-5] ,mixed integer programming [6], machine repair model[7], queuing theory [8], and conventional spreadsheet calculations based on experience and engineering judgments. There are different uncertainties in typical mining operations (e.g. material loading and haulage, drilling, and blasting). For example, in a truck-shovel operation, different governing activities such as loading, haulage, and dumping cycles are stochastic variables. Moreover, analytical modeling of a large truck-shovel operation is very complicated. Thus, application of analytical and/or deterministic techniques cannot guarantee a solution for different problems that are encountered in daily mining operations. Discrete-event system simulation (DES) is a modeling method for such time discrete and probabilistic phenomena [9]. DES has been employed by different researchers in mining engineering through available software and languages such as GPSS, SIMAN- ARENA, and SLAM [10-14]. Most of the studies so far, tried to evaluate some “what-if” scenarios, to understand the possible effects of changing different input variables on overall mine economics. For instance, Baffi and Ataeepur (1996) used Arena to simulate a truck-shovel operation [10]. Also, Sturgul has conducted extensive studies in the application of DES in the mining engineering field [15- 17]. A very good background review of application of this technique in the industry can be found in [15-16]. Previous studies have shown that, different approaches including deterministic, stochastic, and experimental methodologies result in considerable differences in outputs [18]. These techniques lead to different solutions, regardless of the quality of technique/software itself or knowledge of the modeling team. Hence, the first step is to develop a comprehensive simulation framework to obtain nearly the same optimal results for the same input variables, regardless of the employed technique."

Jan 1, 2016

By K. Severin, B. Flanigan, P. Marion

"Plutonic-related" gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As- (Sb-Hg) are a good empirical indicator of the depth of emplacement and distance from causative pluton. These associations have been used successfully in exploration. Results from several analytical techniques also suggest a phenomenological cause for these metal associations. Gold and bismuth have paired mineralogy at high temperatures and, thus, are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2003

By William A. Kapp

INTRODUCTION Coal is being mined from beneath residential areas, structures, bodies of water and other surface features in the coalfields to the north, south and west of Sydney. The particular problems faced by mine operators in these areas vary considerably due to differences in the overlying strata, the variation in the depths of cover and also depend on the number of seams being mined. Detailed subsidence work first commenced in the Southern Coalfield in 1965 and is now being carried out over areas of extraction at roost collieries. The analysis of the results of the early investigations and of the work which continues in other areas has shown that there is a consistent relationship between subsidence and mine geometry and has led to a reliable empirical method for the prediction of subsidence. In addition, particular aspects of each of the studies in the Southern Coalfield results in a clearer understanding of strata movements and of the resulting subsidence. The features of a subsidence trough apply generally to all areas but the magnitudes of specific features vary according to the stratigraphy of the particular coalfield. The aim of the subsidence work is to quantify the effects of subsidence for a range of mining geometries and mining conditions to enable the maximum safe recovery of coal from beneath surface features. The importance of local subsidence investigations is becoming more evident to mine operators and to authorities or organisations with surface interests. The subsidence work also provides important information on the stabilities of pillars of coal which remain unmined between panels of extracted coal. These pillars are not extracted either because of poor mining or geological conditions, or because pillar extraction is not part of the particular mining operation. Subsidence studies over these coal pillars clearly establish whether the pillars have remained stable or have failed to support the overlying strata. With subsidence studies continuing over several years, it is possible to assess the stabilities of these pillars on a long term basis. BACKGROUND TO THE STUDY OF SUBSIDENCE Geographical setting Most of the black coal production in Australia comes from the Sydney Basin. The coal seams extend for approximately 350 km along the coast of New South Wales and inland for distances up to 150 km. The City of Sydney is located near the centre of the coastal extent of the Basin where coal has been mined at a depth of 900 m. The Sydney Basin is part of the Main Coal Province of NSW and is divided into several coal- fields. The Southern Coalfield to the south of Sydney contained 15 operating mines and produced 12.7 million tonnes of raw coal during the 12 months to June 1981. The collieries discussed later are shown in Fig. 1. The prominent topographical feature of the area is the Illawarra Escarpment which rises to 400 m above sea level, or 300 m above the coastal strip along the South Pacific Ocean. The escarpment is mainly sand- stone and the weathering of the cliff line has resulted in a covering of talus material at its base. Several collieries are located near the seams which outcrop along the escarpment. The city of Wollongong is located in a scenically attractive area on the coastal plain. The suburbs of Wollongong extend north along the coastline, south to beyond Lake Illawarra and west to the lower slopes of the escarpment. The Illawarra Escarpment forms the eastern boundary of the Woronora Plateau. On a regional scale the surface dips gently to the west and thus forms a watershed for the rivers, most of which flow in a general north westerly direction, sometimes forming steep gorges in the sandstone. These rivers join the Nepean and Hawkesbury River system and flow into the Pacific Ocean north of Sydney. Seven dam have been constructed over the Southern Coalfield (Fig. 1) and with one large dam further to the west, their stored waters provide the needs of the Cities of Sydney and Wollongong and the surrounding districts. A large part of the area affected by mining is the undeveloped bushland of the associated catchment areas. In general no special precautions have been required with respect to subsidence with the exception of the dam structures and stored waters. With the increase in coal mining activities and the expanding residential development south of the City of Campbelltown in the outer Sydney Metropolitan area, subsidence is becoming an increasingly important area of research. Structures which have been affected or considered are townships and extensive residential areas, buildings of historical importance, major tollways, and a high pressure natural gas pipeline. The subsidence effects of mining beneath natural features within national parks is coming under study as mining approaches these areas. Geological setting The coal seams of the Southern Coalfield lie within the Illawarra Coal Measures. They contain high rank coking coal used in the local steel industry and for export. The Bulli Seam is mined extensively through- out the Southern Coalfield with the lower Wongawilli Seam being second in importance with regard to coal production. The top of the Bulli Seam is taken to be the marker horizon between the Permian Coal Measures

Jan 1, 1982

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots.The four rounds were the standard 26-hole test rounds designed to break 4 feet of rock. The procedure for drilling and blasting these rounds is described in Report of Investigations 3509.Before the regular test rounds were blasted, about 1,200 bounds of fine rock was placed on the steel mucking sheets that covered the end of the adit track; the wails, hack, and floor of the adit were washed thoroughly; and the fine rock on the mucking sheets was completely wetted.Each of the 5 bomb shots consisted of 10 sticks of dynamite tied together and hung at midpoint of the adit, 8 feet from the fall."

Dec 1, 1942