Search Documents

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962

By Franziska Günther, Helmut Mischo

The calculation of costs for an underground mine, as well as the planning of the equipment and materials to be used, is a complex and time-consuming process. The estimation depends on a multitude of parameters, and all mining processes are interconnected. A novel tool has been developed that enables automated calculation of underground mines and allows for the comparison of the effects of changing individual parameters. Previously, changing individual planning parameters often necessitated a complete recalculation of the mine. The newly developed calculation tool provides an innovative planning aid that allows for more efficient and accurate mine planning and cost estimation. The tool enables the user to implement continuously up-to-data costs and prices. This allows for more accurate planning data and results. The underlying concept of the calculation tool, its implementation at a planned quartz porphyry mine in Germany, and the verification of the tool at an existing underground mine will be presented.

Feb 1, 2025

By H. Nagel, A. P. Schissler

"INTRODUCTION Anadarko Petroleum Corporation (Anadarko) owns a region of oil shale properties acquired as part of the original Union Pacific Land Grant of the 1800’s in southern Wyoming. These holdings are greater than 2 million acres and occur throughout the Green River Formation in southwestern Wyoming. One area was prioritized for further study by Anadarko Minerals called the Kinney Rim in the Washakie Basin due to low environmental impact, proximity to infrastructure, high ore grade, and low mining cost. The area is a low-overburden oil shale resource that can be developed using surface mining methods, processed by conventional surface retort, and placing waste rock disposal back on the bench for a design capacity of 10,000 barrel per day. The purpose of this papers is to present the results of environmental analysis and timeline, the mine plan, and surface ore processing to offer a resource-ready energy source.Mineral rights for the Kinney Rim area are owned by Anadarko, the United States Bureau of Land Management (BLM) and the State of Wyoming. Mining of oil shale for this study targets Anadarko owned mineral resources.GEOLOGY The study area is in the Green River and Washakie Basins in western Wyoming. The host geologic member is the Laney Oil Shale. Figure 2 illustrates the Laney shale within a generalized lithologic cross section.OIL SHALE LEASING The proposed Kinney Rim oil shale mining project is located in an area dominated by a 1 square mile checkerboard landownership pattern with every other section typically administered by Bureau of Land Management (BLM) and Anadarko. Surface and mineral ownership is a split estate legal entity. The immediate Kinney Rim mine plan is all on Anadarko sections."

Jan 1, 2015

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and laboratory testing of dust collectors for use on double drum shearers. Systems tested included: ? High Capacity Flooded Bed Scrubber ? Water Powered Extraction Cowls ? Water Powered Extraction Drums ? Water Powered spot Scrubbers. The systems were tested using tracer gas in a full-scale model of a longwall shearer face. This report provides a detailed description of the test facility, test methods, and system test results.

Jan 1, 1982

By H. D. Bemis

This paper describing the milling practice of the American Metal Co. at its Pecos con¬centrator is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. ACKNOWLEDGMENT The author acknowledges the assistance rendered by Guy Martin, metallurgist, H. E. Brown and J. H. Hastings, chemists, and Thomas J. Fahey, accountant, in gathering and pre¬paring the data presented in this paper.

Jan 1, 1932

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By R. H. Bedford, F. T. Johnson

"In California the history of tin mining began in Riverside County in 1853, with the discovery of the Temescal deposit. This deposit remained the only one with a production record until recent small shipments were made from Kern and San Bernardino Counties.According to the California State Division of Mines, Temescal's total output has been about 125 tons of tin, all of which was produced in 1891 and 1892. It was idle from 1892 to 1928.An extensive but unsuccessful development campaign carried on in 1928 and 1929 by the American Tin Corp. produced only half a ton of the metal, and the property again was idle until 1943, when an attempt to resume operations proved unsuccessful. After 1929 no production is recorded from California until 1944 end 1945, when small shipments of sorted ore from Kern County returned about 2 tons of tin and 1-1/3 tons was recovered from sorted ore and concentrates from San Bernardino County. The total output of tin from California has been less than 150 tons, and less than 4 percent of this was produced in the last 50 years, in spite of numerous attempts during that period to promote tin mines,So marked a scarcity of a metal essential in war makes any occurrence interesting. When some prospects were reported to the Bureau of Mines in July 1942, in a new field 10 miles east of Gorman, they were at once examined and the preliminary exploration by the owners closely followed. Eventually one was explored by bulldozing end diamond drilling as a joint project by the Bureau of Mines and the Geological Survey.To supplement this joint project, the authors undertook independently a general survey of tin in California - a survey designed to check reported occurrences and to bring their status up to date. In this work, the 37 places described in the text and spotted on the accompanying map, (fig. 1) were visited end sampled. Although traces of tin were found in many pieces, nothing that suggested a tin mine was found anywhere, and it is difficult to base much hope for appreciable future tin production upon anything found thus far in California."

Apr 1, 1946

The Engineering Index Service, 29 West 39th St , |New York, N Y. (A division of the American Society of Mechanical Engineers ) This Service is the most complete guide to engineering articles as they are published in current engineering literature of the world All branches of engineering are covered It is prepared on standard library filing cards which are mailed every week. Each card contains complete information as to the source of the article indexed and an annotation, or a description, in which there is sufficient information to enable one to select articles of particular interest. With this Service those interested in any phase of engineering may, with a minimum of time, keep in immediate touch with engineering developments throughout the world There are 225 divisions of the full Service, 31 deal directly with mining engineering, and 15 with metallurgical engineering Divisions may be subscribed to separately or in any desired combinations The cost depends upon the extent to which the Service is used Many divisions are priced at $7 a year. Complete information may be had upon request. A suggested mining engineering group of divisions only, follows Division 1, Abrasive industry, 17, Bituminous materials, 21, Brick industry; 33, Clay products industry, 35, Coal mining industry, 36, Coal preparation industry, 76, Fuel engineering, 78, Geology, 79, Geophysics, 82, Gypsum industry, 99, Insulating materials, 108, Lime and limestone products industry, 109, Liquid fuels, 111, Lubricants and lubrication; 122, Metal mining industry, 127, Mineralogy and rare metals and elements, 128, Mine safety and ventilation, 129, Mining engineering and mineral industry; 130, Mining geology; 136, Natural gas and gasoline industry; 141, Nonmetallic minerals industry, 143, Oil field operation, 146, Ore treatment, 151, Petroleum engineering and industry, 152, Petroleum geology; 153, Petroleum refining industry, 154, Petroleum

Jan 1, 1933

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By Berger

A detailed description is given of radio apparatus for controlling a coincidence outfit for relative gravity measurements. This is probably of little interest, since many types of apparatus could be used. The general method employed is the interesting thing about this paper. As long ago as 1883 von Sterneck made a proposal to control two coincidence boxes with the, seine, clock, and many persons have suggested the use of radio for this purpose. In accomplishing this it would appear to the reviewer that this method is probably inferior to that used by the Marland Oil Co., but Berger and Brückner must be given the credit for important advances in the coincidence method. In their apparatus a clock at a central station actuates a relay, which operates a short-wave transmitter (40 m.). At the receiving station the amplification is accomplished at low frequencies... The signal operates a relay which moves a slitted screen in a coincidence apparatus. This screen has been improved considerably, to decrease the mean error in observing a coincidence. As usual, a telescope is used to observe the flashes of light. It has a scale in its focal plane and positions of successive flashes are easily read off and recorded by a second observer. This makes possible' a: higher accuracy in determining the exact instant at which coincidence would have occurred at the zero point on this scale. This method obviously depends on the constance of the mechanical and electrical lag inn both sending and receiving apparatus, and may be adversely criticized from this standpoint. -- A. E. Ruark.

Jan 1, 1929

By Maureen McGuiness

"The pastefill circuit at the Bell Allard Mine in Matagami, Quebec started up in August 1999. The surface pastefill plant produces a cemented paste which is sent underground by gravity through a vertical pipeline in the mine ventilation shaft. Difficulties with paste flow during the start-up highlighted the importance of understanding paste rheology and the effect of operating procedures on line wear. By June 2000, the original circuit had been modified to include a paste pump to transport the paste to the shaft.The steps taken during the paste plant commissioning are discussed. The final flow sheet is presented, focussing on the use of instrumentation to ensure full column flow and proper distribution underground. Resistance modelling and accelerated curing of samples are examined as possible ways of predicting paste resistance to ensure compliance with the mine’s paste specifications.INTRODUCTIONCommissioning a new plant can be difficult and time consuming. The start-up of Noranda’s Bell Allard paste backfill plant was no exception. Since the first day it went into operation, the paste circuit could not meet the tonnage and paste quality requirements of the mine because the paste would not flow by gravity into the vertical pipeline in the mine’s ventilation shaft.Diagnosis of the pastefill problems proved difficult. It was only when the rheology of the Bell Allard paste was understood that the flow problems were solved. To ensure that the paste placed in the stopes meets mine requirements, two methods of paste resistance prediction are being developed."

Jan 1, 2002

By R. F. Linfield

Figure 1-1 shows the basic transmitter design concepts used for the pulse system, the half-wave CW system, and the full-wave CW system. The antenna current waveform is also shown for each transmitter for typical operating frequencies and antennas. The switches shown in Figure 1-i were actually implemented using solid state devices. In all three systems the signaling format may be interrupted to conserve power and thereby extend battery life. Frequency accuracy and stability is achieved using a tuning fork oscillator in the transmitters and tuning fork filters in the receivers for all three systems. This provides the narrow reception bandwidths needed to enhance signal detectability. All three systems also use frequency assignment for identification purposes. The location schemes employed are likewise identical, each being based on detecting the null (signal minimum) of the horizontal magnetic field on the surface. Since these systems are basically similar, the primary purpose is to select the system which gives the maximum signal detectability on the surface from a manpack transmitter operating in the mine. Both the pulse and half-wave C W systems use a d. c. pulse to energize the loop antenna. However, with the pulse system, this pulse duration is short compared to the pulse repetition rate (prf), whereas with the half-wave C W system the pulse duration equals one-half the period of the switching frequency. In the pulse system, energy from the battery is stored in a capacitor so that during the switching interval the internal resistance of the power source can be considered almost negligible. Both transmitters must drive a loop antenna which is a reactive load having inductance, L, and resistance, Ra.

Jan 1, 1973

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

By D. A. Reynolds

THIS REPORT gives results of an investigation of the carbonizing properties of two Tennessee coals, one from the Jellico bed in Campbell County and the other from the Sewanee bed in Marion County. Jellico coal and blends with 20 and 30 percent Pocahontas No. 3 coal were carbonized at 800° and 900° C. by the BM-AGA method. Sewanee coal was carbonized by the same method at 800°, 900°, and 1,000° C.; blends with coals of similar and different ranks were carbonized at 800° and 900° C. The coals were subjected to various physical and chemical tests, including complete chemical analyses, low-temperature assays, and agglutinating, free-swelling, friability, plasticity, and expansion tests. The Tennessee coal field is a part of the Appalachian field, which extends from northern Pennsylvania to central Alabama. The Jelico bed, one of the most important in the State, is part of the Jellico formation, which is above the Lee formation of the Lower Pottsville. Sewanee coal bed belongs to the Sewanee conglomerate and is stratigraphically lower than the Jellico bed.

Jan 1, 1953

By Aarne Visnapuu

Unmodified pneumatic rock drills may have noise levels of 115 to 130 dB at the operator's position. Experimental modifications have been made to a standard drill to suppress the noise from the three main sources: the air exhaust noise, the noise radiated from the drill, and the resonance noise of the steel drill rods. A prototype model developed at the Bureau of Mines, Rolla Metallurgy Research Center, operates at a noise level below 100 dB. A close-fitting case and muffler unit, consisting of a metallic skeleton filled with viscoelastic absorber and having a durable cover, provided both muffling and noise absorption. Damping alloys were used at strategic points in the drill. Drill steel resonance noise was reduced by a constrained-layer treatment on the outside of the drill rod. The singular and combined effects of the treatments are presented in detail.

Jan 1, 1973

Since the days of Adam Smith and Milton Friedman the discussion of corporate citizenship and sustainability has been flooded with multiple contradictions, with proponents of sustainability saying that it is a crucial cog in the business strategy, while those against, maintain that æthe business of business is businessÆ and therefore sustainability issues are just add-ons. Sustainability arises from a deeply held vision by corporate leaders that businesses can and should play a role beyond just making money. Businesses should embrace the understanding that everything that a company does has an impact both internally and externally (communities, employees and customers), and the natural environment. This paper highlights the approach that led to a view that there is a contradiction between profitability, sustainability and community development, and we provide a further argument to the contrary. This argument is based on a comprehensive literature review of over three decades by various scholars linking corporate social performance and corporate financial performance. Driefontein Gold MineÆs approach is that of linking the community development, natural environmental and employee well-being initiatives and projects to the mineÆs business strategy. The paper further highlights the coordination and implementation mechanism of sustainability at the mine where the accountability lies with the head of the mine operations. A two pronged approach is employed where there is an internal dialogue on sustainability between the various departments coordinated by the sustainable development department and an external tri-sector partnership with local government, interested and affected parties and the mine. These approaches are closely linked to the contributions towards the mineÆs financial bottom line.

Jan 1, 2009

By Daniel C. Jackling

WHAT is written here features some of the things that I would say if I were to de- liver a Presidential address during the Annual Meeting to be held this month in New York. I am aware that custom favors written rather than vocal delivery of such a discourse; and, as this accords exactly with my own preference, I assure readers that they will never be called upon to hear these remarks spoken- anyhow, not by me. My year as President is drawing to a close. As I look back I like to classify and analyze the impressions that have been left with me. It has been a delightful and fascinating experience to me personally; I have appreciated the courtesies and aids, and have been deeply gratified at the honors accorded me. Perhaps the source of greatest satisfaction is the opportunity I have had to sense more about the provinces of this Institute and about the useful functions of the profession that it represents. For 38 years I have been a member. I served two terms as Director-one in 1914-'16 and again in 1927-'29. I have been honored by selection as a Saunders Medalist. I thought I was reasonably familiar with the functions, the ideals, and the activities of the Institute. But the things that I have discerned during the past year have dispelled that conceit. I still think that, a year ago, I was as well informed as most members; but since then I have had the rare privilege of executive service and insight. That has given me a perspective that I feel can be obtained in no other way-as I think the illustrious engineers who have preceded me in office will agree. I wish that I had the power to translate to every member somewhat of the feelings of pride in our organization that a year as President cannot help but instill.

Jan 1, 1939

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By Karl V. Lindell

THE Jeffrey mine of the Canadian Johns-Manville Co., Asbestos, Que. has operated for a number of years, supplying the parent company, Johns-Manville, raw material for asbestos products. The mine is situated in the 70-mile-long serpentine belt running from Asbestos, Que. on the west to East Broughton on the east. This district is the most important producing area in the world of quality spinning-fiber asbestos, with 11 operating mines supplying 70 pct of the world's needs. The Jeffrey mine, located 90 miles from Montreal and approximately 35 miles southwest of Thetford, accounts for 50 pct of the Canadian asbestos output. Production from the Canadian serpentine belt is the chrysotile asbestos, which is considered the best available for spinning. Consumers in the United States prefer the clean, fine fibers of the Canadian chrysotile of the type produced by the Jeffrey mine. Mining In 1881, when the mine was first opened, all work, including drilling, was done by hand. The deposit, located on a hillside, was first worked as a sidehill cut by hand drilling 15-ft holes and blasting with black powder. The fiber was chiselled from the broken rock. Hand derricks, later powered by horses, were used to raise the rock as the pit deepened. Eventually, the pit became so deep that derricks were, by necessity, replaced by aerial tramways. In the late 1930's, further deepening of the open pit, with the resulting constriction of the pit bottom brought about the need for altering the mining system then in use. The high ratio of overburden to be handled to mill ore mined and the value of surface structures, not company property, that would be destroyed in expanding the area of the pit, definitely indicated vertical rather than horizontal expansion would have to be used. One exception to this was that a small area on company property to north and east of the pit could be opened up. The mining problem then resolved itself into two phases; make the small lateral expansion and as rapidly as possible choose a mining method that would expand the mine vertically. Several methods for vertical expansion were studied and rejected. Methods considered included shrinkage stoping, block caving, glory holing, and various modifications of open workings. Block caving was finally accepted as the most suitable method of underground development. Cost factors and production were important factors in the decision, also, the asbestos mines in the Thetford area were already having success with this method. Original plans provided for the lateral expansion of the open mine where possible and beginning the underground operation. This program was based on the open pit being worked out in 1954, with the underground development and production gradually increasing until the open mine was depleted. In 1949, the plan was changed to allow underground development to progress at maximum so that underground output would be 550 tons per hr by 1951. Any deficit in ore would be mined from the open pit. This change permitted extending the life of the open pit through 1964 and in this time would make available a large quantity of readily attained ore. Block Caving at The Jeffrey Mine Plans for the underground operation were formulated on a 12,000-ton-per-day basis, and the adaptability of block caving methods to high production presented a desirable situation. As shown in the main-haulage plan, a continuous loop was laid out for smooth operation of the underground railroad from the loading points to the underground crusher. A feature encountered at the Jeffrey mine, as well as other asbestos mines using caving methods, is the large size of caved material, requiring that ore be crushed before hoisting.

Jan 1, 1952