Search Documents

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By G. Eaton

Safety management is an important mortal and business function in construction. Contractors have traditionally tracked and reported lagging indicators, e.g. fatalities and lost-time accident rates, to measure their safety performance and stay in compliance with relevant regulations. Over the last several decades, contractors became more proactive in their approach to safety and developed programs that track leading indicators, e.g. safety audits and safety climate. In particular, safety climate measures workers? perception of safety management and its effectiveness in the workplace. Past literatures indicated that, while some industrial construction contractors ignore safety climate measures, others are limited by a lack of a formal means to measure safety climate. In this study, a survey approach is used to measure an industrial construction contractor?s safety climate through three key areas: management commitment, job control, and general safety climate. As a pilot study, a total of 214 individuals at a fabrication facility participated in the survey to verify the validity and effectiveness of the proposed survey approach. This survey study also confirms that job control and management commitment have a positive correlation and that worker demographics have an effect on respondents? perceptions of management commitment.

Aug 1, 2013

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By J. A. Restrepo, K. D. Luxbacher

"The U.S. underground coal mining industry has recently seen the occurrences of several multifatality events that have interrupted an otherwise steadily improving safety record. These events transpired even with an unprecedented level of government regulations and safety technologies. These events may indicate that current safety practices have reached a level of diminishing returns. Risk management, a safety approach that has been successfully applied in numerous industries including mining, may provide a means to overcome this plateau. Riskgate is an Australian mining risk management program that may be successfully applied in the United States. However, fundamental differences between the Australian and U.S. coal mining industries prevent direct implementation. This paper discusses aspects of the Riskgate body of knowledge that require adaptation for its application in the United States. IntroductionThe underground coal mining industry in the United States has recently seen the occurrences of several high profile, multifatality events. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with minimal declines in fatal and nonfatal injuries over the past decade may signify that current safety practices have reached a level of diminishing returns. In order to surpass this plateau, a modification to the manner in which the mining industry approaches worker safety may be warranted.The implementation of a risk-management- based approach may potentially provide a means for not only surmounting the current safety stagnation but also for achieving the long-desired objective of zero harm.Riskgate is an Australian risk-management- based body of knowledge that shows great potential for application in the United States. This paper discusses aspects of the Riskgate body of knowledge that require adaptation for the U.S. mining industry. The proposed adaptations are based on differences in operating practices and government regulations. This discussion will focus on the three major U.S. risk areas of explosion prevention, ground control and moving equipment."

Jan 1, 2015

By Glen Mann, H. G. Vestberg, Robert D. Holtz

"Underpinning of residential and commercial structures is often accomplished using a number of driven-in-place small diameter steel pipe piles. These piles, at least in the Seattle area, are typically described as pin-piles and are driven with an air compressor operated jack hammer to a refusal criterion developed from an empirical basis. Over the past twenty years or so, the materials have improved in quality and strength, and the driving equipment has improved in efficiency and capability. These improvements have resulted in damage to the pin-piles during driving as well as to the driving equipment. The primary objectives of this load testing study were to develop a relationship between the driving penetration resistance of 2-inch diameter pin-piles and the ultimate bearing capacity when piles were driven at different penetration rates and, based on the load test results, to develop an opinion regarding an increase in the allowable axial load capacity [ultimate load capacity divided by a factor of safety] of a 2-inch diameter pin-pile over the currently used permissible load capacity of 4 kips in the Seattle area. Also, if feasible, a reduction in the present driving penetration rate was to be recommended to help reduce the rate and magnitude of pile and equipment damage whilst maintaining the allowable load capacity. The recorded ultimate bearing capacities were also compared with the Tagnent-line and the Davisson analytical methods in an effort to determine if either of these provided a reasonable determination of the pile load capacity.IntroductionThis paper describes the results of a series of load tests performed on small diameter, 2-inch, driven-in-place steel pin (pipe) piles and based on these results, provides the support for a modification to the presently used allowable axial pin-pile capacities.The intent of the load testing program was to determine how much influence the penetration resistance might have on the individual piles' ability to support the allowable axial load without undergoing any significant vertical deformation. For the purposes of this paper the ""allowable load capacity"" is considered to be the ultimate pile load capacity divided by a minimum factor of safety, typically considered to be 2.0 in this area. A pin (pipe) pile comprises an open or closed ended, schedule 80 steel tube which is driven-in-place, usually with an air compressor operated 90 pound pneumatic jack hammer. These jack hammers typically operate at a rate of about 1,200 blows per minute, (Haggard, Holtz and Mann, 2001 )."

Jan 1, 2005

By Robert Perlman

The paper point out which area of conflict between international companies y and less developed countries. The lost year the lees developed countries were received invesment very low as to that they can grow and expan. Likewise the foreign investment led easily to its fair share of explicitation and bloodshed. In the same way, the alternative to a particular development being undertaken by foreign capital is either that investment does not take place at all or that capital resources are diverted from somewhere in the domestic economics, in which case some other piece of investment does not take place.

Nov 20, 1969

By Ron Hatch, M. K. Witte

"INTRODUCTIONThe proper selection of carbon for a gold carbon in pulp (CIP) circuit involves careful evaluation of several physical, chemical and economic factors. A series of evaluations are required to maximize gold recovery at the lowest capital and operating costs, whether the carbon is selected for an existing gold mill circuit or a new mill under design.Although evaluation may proceed through various stages, it is the intent of this paper to outline some of the preliminary testwork that should be carried out to screen potential carbons for a particular application.An examination of the specification sheets supplied by the various carbon manufacturers may indicate some desirable properties on which to make cursory selection. This exercise by itself will not provide the basic data needed for selecting the best carbon for a particular ore pulp and metallurgical circuit. The necessity of further metallurgical evaluation is indicated by the fact that different carbons perform differently depending on the physical and chemical nature of the leach pulp. In the case of an existing mill, actual leach slurries using mill water are available and should be used for testwork. In the case of new mills, leach pulps must be prepared to simulate the proposed circuit.Five coconut shell activated carbons were obtained from various suppliers, all reported to be 6 x 16 mesh carbons recommended for CIP circuits. A metallurgical evaluation was made utilizing two leach pulps with significantly different characteristics. This paper describes the test procedures utilized and the results obtained from the testwork."

Jan 1, 1985

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By H. E. James

Much has been said and written about the need to reduce South Africa's dependence on gold. To compensate for the decline in the country's foreign-exchange earnings resulting from the phasing out of gold, which must inevitably occur at some future date, a far higher priority will have to be placed on the mining, beneficiation, and export of the 59 other mineral commodities produced in South Africa. The basic strategy of the mining and metallurgical industries should be to move from the traditional approach of establishing a resource base to the establishment of a market base; to turn from production orientation to market orientation; and to rely less on exploration and economies of scale and more on process innovation and product development. The enthusiasm, entrepreneurial spirit, and commitment of the leaders in the mining and metallurgical industry will clearly be of decisive importance in the establishment of new industries for the beneficiation and export of added-value mineral-based products. The State can make a significant contribution by the provision of a welldeveloped and efficient infrastructure, including rail and harbour facilities, communications and health services, roads, and of electricity and water supplies. In our search for a new development strategy for the beneficiation and export of South Africa's minerals, we need to recognize that no one nation has all the mineralresources that it needs. Commercial and strategic manipulation of mineral supplies should no longer be tolerated. The future of the human species lies in international cooperation and in a greater understanding of the limitations of the world we live in.

Jan 1, 1985

By James C. Ray

DURING the summer of 1931, I spent four months in a study of the Willow Creek district, Alaska. This work was part of a general investigation of the territory contiguous to the route of the Government- owned Alaska Railroad. It was conducted by the U. S. Geological Survey to determine the real and potential merits of the mineral deposits, to stimulate development of them, and thus to increase the traffic on the Alaska Railroad.

Jan 1, 1932

By S. Vennos

As a result of Synopsis 73-16 Dynadyne responded with an unsolicited proposal offering the Bureau of Mines to develop an ultra-low volume coal mine dust personal sampler. In the ensuing technical discussions the choice of a desirable volumetric rate became a focal point. While, the initial proposal was based on a volumetric rate in the area of 50 cc/min the Government expressed interest in a variety of mass flow rates ranging from 50 cc/min to 2000 cc/min. The physical characteristics such as weight, volume and configuration of a personal sampler are to a large extent - dependent on the operating volumetric rate. It became readily apparent that the optimum size of such an instrument as a function of volumetric rate was not known and that a study of the choice of optima was essential prior to beginning the development, Hence, the Government authorized a two phase approach to this project. Phase I was to include a Technical Evaluation Study of optimum characteristics in the range between 0. 1 to 2. 0 lpm. Based on these findings and in consultation with MESA personnel, the Bureau of Mines was to authorize the second phase that is, the development. Phase II, was to include the drawing of a set of performance specifications stating among others the desired operating volumetric rate. In this report, every effort was made not only to present the actual work done over the course of this development, but to reflect also our engineering "thinking" providing answers as to the "why" we preferred certain solutions over others. We believe that this added dimension is not only useful for the Government official evaluating this report, but also that the Government is entitled to it providing the official with an educational content useful in avoiding future costly repetitions of similar situations.

Jan 1, 1975

By Sam Tour

OF the new alloys achieving commercial prominence during the year, an aluminum-silicon magnesium casting alloy, which is similar in many respects to the 4 per cent copper alloy, developed about 1921, which has attained such a wide field of service, may be mentioned. The new alloy, like the old, is a heat-treatable type and develops about the same physical properties. The alloy casts easily and is relatively insensitive to high pouring temperatures. Its ability to produce substantially leak- proof castings is noteworthy. A second casting alloy development is the new Aluminum Co. of America No. 132, "Lo-Ex" piston alloy, a result of nearly eight years of research. The alloy contains about 14 per cent silicon and varying amounts of nickel, copper, and magnesium. It exhibits a low coefficient of expansion and thus permits small piston clearances. Its lower specific gravity is a further advantage.

Jan 1, 1932

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Christopher Mark

"Many problems in rock mechanics are limited by our imperfect knowledge of the material properties and failure mechanics of rock masses. Mining problems are somewhat unique, however, in that plenty of real world experience is generally available and can be turned into valuable experimental data. Every pillar that is developed, or stope that is mined, represents a full-scale test of a rock mechanics design. By harvesting these data, and then using the appropriate statistical techniques to interpret them, mining engineers have developed powerful design techniques that are widely used around the world. Successful empirical methods are readily accepted because they are simple, transparent, practical, and firmly tethered to reality.The author has been intimately associated with empirical design for his entire career. But where his past papers have described the application of individual techniques to specific problems, the focus of this paper is the process used to develop a successful empirical method. A six-stage process is described:1. Identification of the problem, and of the end users of the final product2. Development of a conceptual rock mechanics model, and identification of the key parameters in that model3. Identification of measures for each of the key parameters, and the development of new measures (such as rating scales) where necessary4. Data sources and data collection5. Statistical analysis6. Packaging of the final productEach of these stages has its own potential rewards and pitfalls, which will be illustrated by incidents from the author’s own experience. The ultimate goal of this paper is to provide a new and deeper appreciation for empirical techniques, as well as some guidelines and opportunities for future developers."

Jan 1, 2015

By D. E. Deegan, G. Holcroft, T. P. Johnson

"The rising cost of extracting metals from existing traditional deposits, increasingly stringent environmental regulations and a greater awareness of corporate social responsibility issues are all factors in stimulating the examination of mine tailings and small-scale alluvial deposits as a potential source of new raw materials. Furthermore, despite tougher economic times the demand for commodities remains strong, in no small part as a result of the growth of the world’s emerging economies.This combination of social and economic factors looks set to continue in the long term which will encourage greater recovery of materials from previously ignored sources such as mine tailings and ores from alluvial deposits.An expansion in the recovery of useful materials from mining-related activities is likely to require the use of robust and innovative techniques that have a built-in degree of future-proofing; DC plasma technology is one such technology.As a result of its ability to separate the valuable metal and minerals from the waste material while destroying hazardous compounds, Tetronics’ DC arc technology offers an alternative approach to resource recovery from a wide range of mine ores. Harmful cyanide compounds and the vast quantities of water used in conventional hydrometallurgical processing are avoided when plasma processing is adopted. DC arc technology also brings additional benefits, including: the extremely effective destruction of organic materials, the conversion of the inorganic material into a re-useable aggregate and the high tolerance of the process to fine and dusty materials. This paper presents details of Tetronics’ DC arc technology as one of the key pyro-metallurgical solutions available for the recovery of valuable materials from traditional mine ores and tailings, as well as giving specific examples of how the technology has been successfully employed in the recovery of enriched slags, ferroalloys and other metals."

Jan 1, 2016

By Ott F. Heizer

This paper describing the practice at the tungsten concentrator of the Nevada-Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on milling practices, methods, and costs in the United States. The ore, which contains about 1.10 per cent of scheelite (CaW04), is concentrated on tables and by means of a magnetic separator and roasters. A product containing 70.43 tungsten trioxide is shipped. The plant was designed for a capacity of 100 tons per 24 hours, but at present 142 tons of ore are milled per day. The author acknowledges the assistance of William O. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in preparing this paper.

Jan 1, 1930

By Charles L. Morgan

In June 1996, the United Nations International Seabed Authority opened shop in Kingston, Jamaica as an autonomous international organization charged with the administration of seabed mineral developments in all areas beyond national jurisdictions. The Authority is a consequence of the 16 November, 1994 entry into force of the 1982 United Nations Convention on the Law of the Sea (UNCLOS) and the 1994 Agreement relating to the Implementation of Part XI of UNCLOS. The total seabed area included within the Authority?s purview has yet to be assessed accurately, but clearly constitutes the largest single jurisdiction on the planet. The Authority is governed by legislative bodies called the Assembly and the Council and an administration called the Secretariat. The Assembly includes representatives of the 132 member states which are currently parties both to UNCLOS and to the 1994 Agreement. These member states directly fund the operations of the Secretariat. They include most of the world?s developed nations, island nations, and others among the 188 independent countries which are members of the United Nations. Notably absent are the United States and Canada, which are the only developed coastal states not represented. The Council is a 36-member subset of the Assembly representatives selected through a somewhat involved process designed to achieve a balanced representation of the specific interests of the members. Ultimate responsibility for the Authority?s actions resides in the Assembly, but most initiatives originate in the Council. Also included in the Authority are two subsidiary advisory bodies, the Finance Committee, which reviews the Secretariat?s budget, and the Legal and Technical Commission, which evaluates claims and drafts technical regulations. The Secretariat itself includes a staff of about 30, including 15 highly qualified and competent attorneys, accountants, engineers, and scientists. Details describing the composition and activities of these bodies can be found at the Authority?s website (http://www.isa.org.jm).

Jan 1, 2000

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By Stuart D. Miller, Clayton L. Rumble

"A field net acid generation (NAG) test procedure has been utilized on-site to identify, classify and map potentially acid forming overburden at the PT Kaltim Prima Coal (K.PC) mining operation situated in the tropical equatorial region of East Kalimantan, Indonesia. The field procedure involves routine use of a calibrated, site specific NAG test (rapid oxidation test using hydrogen peroxide) which has a tum-around time of less than 24 hours and requires minimal sample preparation. It is used on geological drill-hole samples, for forward planning and overburden management; blast-hole samples, for day-to-day operational control and overburden scheduling; and final dump surface samples, for verification testing. This operational monitoring program has been in use at KPC for the past four years.Calibration and implementation of the field procedure has involved validating the NAG test using conventional acid-base accounting techniques, producing an overburden geochemical classification scheme, optimizing laboratory and sample preparation procedures, and ongoing quality management. This paper presents background theory and practical application in a case study format."

Jan 1, 1999

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022